CHINA DRAGON TECHNOLOGY CDT-H18188E-NX WIFI Module User Manual
CHINA DRAGON TECHNOLOGY LIMITED WIFI Module
User manual
␡ൣᐲѝ嗉䙊⭥ᆀ、ᢰᴹ䲀ޜਨ CHINA DRAGON User TECHNOLOGY LIMITED Manual Part Name: WIFI Module Part No.: 8188 series Date: 2014-6-25 Part 1˖ ˖Introduction This product is a new generation module, It is based on USB interface, accord with Wifi wireless network standard embedded module, the built-in wireless network protocol IEEE802.11 protocol stack, and TCP/IP protocol stack, save electricity intelligent control procedures , realize the user serial data to the wireless network conversion between. The entire module needs a power supply of product has integral antennaantenna and alternative PCBantenna) antenna totouse of 3.3 3.3 volt, volt, and and the it has two Antenna(integral and PCB use. for But it isn't a MIMO equipment. Botha of the antenna was used independent. Whenwas used a different product. But it isn’t MIMO equipment. Both of the antenna the customer need a PCB antenna, and the integral antenna will be take out, vise versa. independent. When the customer need a PCB antenna, and the integral antenna will be take out, vise versa. Through the Wifi module, the traditional serial equipment also can easily access wireless network. gInterface˖PIN gPower supply voltage: +3.3V gWireless Features: -- Compatible completely with IEEE 802.11 a/b/g/n standards -- Compliant to IEEE 802.11 a/b/g/n Wireless LAN Standard -- Channel frequency: 2412-2462MHz for 802.b/g/11n H20 mode ; 2422-2452MHz for 802.11n H40 mode -- 802.11b/802.11g /802.11n(HT20): 11channels 802.11(HT40): 7channels gExternal Antenna can choose miniature coaxial connector˄U.FL˅type gOthers: -- Supports many kinds of network protocols: TCPǃUDPǃDHCPǃICMPǃ DNS etc -- Supports USB transmission mode -- Can provide a user interface to set configuration parameters gApplication: Temperature controllerǃSmart meterǃHousehold applianceǃ remote controlǃSecurity ProductsǃToy, and other IOT industry(sunch as retail business and medical care etc). Part 2˖Product Description This part comprehensively introduces hardware interface and product function of the WIFI module, in this way can help user to the familiar with using the WIFI module quickly and efficiently, and can start using it sooner. Module Interface : Standard 2.54 PIN System Interface: can using socket or connection terminal mode WIFI Module Top View WIFI WIFI Module ModuleBottom BottomView View(copper covered) WIFI module Size and PIN Description No Pin name LED GND D+ DVCC WPS Antenna Description It is connected to an external LED to show the module operating status Ground USB Data + USB Data ̢ 3.3V It is connected to an external push button to activate WPS. Integral antenna PCB Antenna This product has integral antenna and alternative PCB antenna to use . But it isn't a MIMO equipment. Both of the antenna was used independent. When the customer need a PCB antenna, and the integral antenna will be take out, vise versa. Integral antenna: 2.0dBi PCB Antenna: 0dBi Antenna Information˖ IPX antenna interfaceˈthrough miniature coaxial connector˄U.FL or IPEX˅ connection to WIFI module 2.4GHzWIFI antenna L=145mm FCC statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example, USB dongle like transmitters is forbidden. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: ROWCDT-H18188E-NX Or Contains FCC ID: ROWCDT-H18188E-NX ” when the module is installed inside another device, the user manual of this device must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : CDT2820 Create Date : 2015:04:20 18:18:28+08:00 Modify Date : 2015:04:20 18:18:28+08:00 Subject : XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Metadata Date : 2015:04:20 18:17:52+08:00 Creator Tool : Acrobat PDFMaker 11 Word 版 Document ID : uuid:31d30001-def5-4970-a579-589dc374cc2e Instance ID : uuid:7b3fab8b-8530-45d3-8231-eefdd632e176 Format : application/pdf Title : Description : Creator : CDT2820 Producer : Acrobat Distiller 9.0.0 (Windows) Keywords : Source Modified : D:20150417031436 Company : Manager : Comments : Category : KSO Product Build Ver : 2052-9.1.0.4716 Page Count : 6EXIF Metadata provided by EXIF.tools