CIG 802W WiFi Module for use in Extender Products User Manual Host

Download:
Mirror Download [FCC.gov]
Document ID	3625428
Application ID	iKMfzTFFohu/m86x7ncZcw==
Document Description	User Manual (Host)
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	24.72kB (308979 bits)
Date Submitted	2017-11-01 00:00:00
Date Available	2018-04-30 00:00:00
Creation Date	2017-09-27 13:49:58
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2017-09-27 13:49:59
Document Title	User Manual (Host)
Document Creator	Adobe InDesign CC 2017 (Windows)

G.hn
Solid Amber: Device is ON but G.hn is not
paired with any device.
Blinking Amber: Trying to discover and
pair with other G.hn devices.
Solid Green: Device is paired with anther
G.hn device and link is up.
Fast blinking Green: G.hn is trying to
connect to other devices.
Slow blinking Green: G.hn connected as
the backhaul transmission
LAN
Solid Green: Ethernet port link is up
Slow blinking Green: G.hn connected as
the backhaul transmission
OFF: No Ethernet connectivity
Wi-Fi
Solid Amber: Default SSID is broadcasted
(“Guide_xxxxxxxx”)
Solid Green: Specified SSID is broadcasted
Slow blinking Green: G.hn connected as
the backhaul transmission
OFF: No SSID is broadcasted
Pairing
button
G.hn pairing: Pressing the button more
than 1s, less than 10 seconds(Amber G.hn
LED starts blinking(0.5s on, 0.5s off)), after release it, starts the pairing procedure
and opens the configuration period.
Factory reset: Press the paring button
and hold until all LEDs turn on(It takes
longer than 10 seconds)
Boot
up
During booting, all green LEDs turn on until
the booting process completed
1. Overview
• G.hn wave 2 over powerline
Quick Start Guide
WF-802GW
G.hn+Wi-Fi extender
• Integrated Wi-Fi mesh extender (*Note that
WF-802GW can be used in combination with WF802G which is not equipped with an integrated
Wi-Fi mesh extender)
• 2x2 2.4Ghz 802.11n and 2x2 5Ghz 802.11ac
• 1x GbE RJ45 LAN
• Push-button pairing
• Status LEDs
CIG Shanghai Co., Ltd.
5/F Building 8, 2388 Chenhang Rd.,
Minhang District Shanghai 201114,
China
Tel: +86-21-8023-3300
support@cambridgeig.com
G.hn: Green/Amber
Ethernet: Green
Wi-Fi: Green/Amber
2. Installatation
Step 1: Plug a WF-802GW into the power outlet
close to the home gateway.
Step 4: Repeat Step 3 to add more WF-802GW
at different locations which Wi-Fi network extension is required.
3. Pairing
Step 2: Using Ethernet cable connect the
WF-802GW to a LAN port of your residential
gateway.
Step 3: Plug another WF-802GW into the power
outlet at the location that the Wi-Fi network
extension is required.
Step 1: Once the G.hn LED is solid amber, push
the pairing button between 1 to 10 seconds,
until the G.hn LED is starts blinking.
6. Management App
Step 2: Repeat Step 1 for all plugged-in WF802GW devices.
For IOS, please scan the following QR code to
download:
You can download the HomeMesh App to monitor
and configure the WF-802GWs.
Step 3: The green G.hn LED shows that the
WF-802GW devices are paired. If the G.hn LED
is OFF, factory reset is required by pushing the
paring button for more than 10 seconds and
then repeating Step 1 to pair the device with
the network.
Step 4: Repeat Steps 1-3 to connect a newly
installed WF-802GW.
For Android, please scan the following QR code
to download:
4. Ethernet Connectivity
WF-802GW can be connected to computer via
Ethernet cable.
5. Wi-Fi initialization
Step 1: Use a computer/smartphone to search
and connect to the Wi-Fi network of Guide_
xxxxxxxx (x is a digit). Here is an example of
broadcasted Wi-Fi network.
Step 2: Once the computer/smartphone is connected to the Wi-Fi network, the below window
pops-up. If not, open an Internet browser and
enter a URL address (e.g., www.cambridgeig.
com) or IP address of 192.168.1.100.
Step 3: Within the webpage, set your home
network SSID and password (this information
will be used for your phone, tablet, or computer
to connect to the network). When apply button is
clicked, the information will be saved and applied
to the all paired WF-802GWs automatically. The
Wi-Fi LEDs of all devices will be changed from
solid amber to solid green.
After install and connected to your home Wi-Fi
network, please input your Wi-Fi password to
login.
Federal Communications Commission (FCC)
Interference Statement
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment may generate, uses and can radiate
radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:(1)
This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the device and your body.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Language                        : zh-CN
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c137 79.159768, 2016/08/11-13:24:42
Create Date                     : 2017:09:27 13:49:58+08:00
Metadata Date                   : 2017:09:27 13:49:59+08:00
Modify Date                     : 2017:09:27 13:49:59+08:00
Creator Tool                    : Adobe InDesign CC 2017 (Windows)
Instance ID                     : uuid:6344a50d-b501-4750-b0c1-7305f66d5d55
Original Document ID            : xmp.did:f89eebd6-dde2-4175-8672-069c59bba3ce
Document ID                     : xmp.id:9cfec1f2-08cd-204d-b1d8-c902cd65d8c9
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:0ce3ced0-83a4-a740-a0fe-24469a75cbe9
Derived From Document ID        : xmp.did:0ce3ced0-83a4-a740-a0fe-24469a75cbe9
Derived From Original Document ID: xmp.did:f89eebd6-dde2-4175-8672-069c59bba3ce
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Windows)
History Changed                 : /
History When                    : 2017:09:27 13:49:58+08:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CC 2017 (Windows)

EXIF Metadata provided by EXIF.tools