COLEMAN / EVCON IND. Furnace/Heater, Electric Manual L0611481
EB10B EB10B COLEMAN EVCON FURNACE/HEATER, ELECTRIC - Manuals and Guides L0611481 View the owners manual for your COLEMAN EVCON FURNACE/HEATER, ELECTRIC #EB10B. Home:COLEMAN EVCON:/ Furnace Parts:COLEMAN EVCON furnace parts:#EB10B COLEMAN EVCON furnace parts:#EB10B COLEMAN EVCON furnace/heater, electric manual
User Manual: COLEMAN COLEMAN / EVCON IND. Furnace/Heater, Electric Manual COLEMAN / EVCON IND. Furnace/Heater, Electric Owner's Manual, COLEMAN / EVCON IND. Furnace/Heater, Electric installation guides
Open the PDF directly: View PDF 
.
Page Count: 20
| Download | |
| Open PDF In Browser | View PDF |
DOWNFLOW/UPFLOW ELECTRIC FURNACE MODELS: EB SERIES Incorrect installation may create condition where the operation of the product could cause personal injury or property damage. The furnace shah be installed cal components are protected so the electrifrom water. CAUTION] This product must be installed in strict compliance with the enclosed installation instructions and any applicable Local, State and National Codes including, but not limited to building, electrical, and mechanical codes. Improper installation will void the warranty. 66669 035-15266-003 Rev. A (0804) 035-15266-003 Rev.A (0804) GENERAL INFORMATION CODES The electric EB FURNACE NOTES following The following regarding list includes the EB furnace 1. Furnace 2. Heating 3. Filters 4. Filter size is universal important facts and and its packaging are furnished thermostat Standard inclusions: is rated at 240 volts, 60 Hz, single and Cooling information is packed tilating phase. for the Installation (NFPA National Systems Electric Canadian A 1-7/8 B 2-5/8 C 3-1/2 D SUB-BASE, IF USED, ADDS 7/8" MORE TO TOTAL HEIGHTAND 3/8" TO WIDTH. of Warm 90B) (NFPA 70) Code, for servicing any furnace. F 5-1/2 G 5-13/16 Part l (CSA 1 J 1-3/4 K 7-13-16 L 8-5/8 M N 9-7/16 16-1/2 for access access may furnace 24 inches FURNACE Electric THERMOSTAT WIRING to the heating is approved material inlet or outlet duct paragraph on Return RETURN AIR must have a certain M FOR for zero (0) in. clearance work. Clearances WIRING ENTRY OPTIONAL BOTTOM FIELD HEATING must be and provided of 200 sq. inches free open- other above than shown see to work Use Return Minimum thermostat operation See Figure for heating Grille with minimum AND Coil cavity 8. All furnaces 200 in 2 free area opening. HP UP TO 3 1/2-TONS Grille 7900-287P/B, 1FG0620BK Door 3500-1581,3500-5851 Or any Return Grille with minimum (hinged), (bulk pack), 250 in 2 free area opening. and cooling. FOR A/C UP TO 5-TONS 7. air. 250 in 2 free area opening. Or Louvered 1. or alcove for return Grille 7900-287P/B, Use Return size is the same for all models. a closet ONLY FURNACE FOR A/C UP TO 4-TONS FIGURE 1 : FURNACE DIMENSIONS properly, total free area opening 200 in 2 free area opening. Or any Return AND HP UP TO 4-TONS built into furnace. are equipped and is AiC or Heat Pump 9. Holding 10. This furnace strap furnished is designed Page 6 for upflow This furnace with an air conditioner Minimum blower ready. for downflow Or any Return how- The return air opening (See a sidewall above instruction.) the furnace. without side the front walls height, furnace and its components equipment combination as a system ries for the United States listed sticker on the A/C were by Underwriter's and Canada. listed Laborato- in or closet 6 inches side where furnace grille door return grille cannot (bulk pack), anywhere in a closet front door or or in a Iouvered air is located below furnace must be provided is located to provide installed start more clearance above than casing on the for proper air is not required the furnace three door on in the floor, clearance 2. The 6 " minimum is a return This return casing, for the return minimum (hinged), 330 in 2 free area opening. can be located the furnace If opening flow. See Figure if there 1FG0125 Grille with minimum application; conversion Pump 1 RF1025BK, Door 3500-1591,3500-5861 to an upflow application. must not be operated Heat Grille Or Louvered panel installed. This furnace 330 in 2 free area opening. Use Return on top rear of furnace. ever, it may be converted 2 to com- exterior Air. for the furnace Minimum and the wall or partition. for a minimum In order NOTE: This or by locating N ENTRY 11. and controls. door of in front of the on all or any part of the furnace WIRING Four-wire in the location elements by a closet from a facing FIELD 6. factor of 24 inches ing for return air. For clearances Furnace C22.1) CLEARANCE furnace bustible a minimum be provided above the furnace 5. and Air codes take precedence over any recmade in these instructions. is an important Provide furnace the ENTRY Air Heating (state/county/township). All applicable ommendation Access 5-1/16 H and Ven- LOCATION 1 E with the of Air Conditioning (NFPA Code Electrical All local codes NOTE: 19-5/8 in accordance 90A) for the Installation Conditioning - 16 x 20 x 1. must be installed Systems Standard with furnace. with each model. to all models furnace codes: height. feet above the height. Unitary Products Group 035-15266-003 Rev.A(0804) There must be at least 2 ft. of space available in front of furnace for servicing the furnace when necessary. 23" MIN. DUCT SYSTEM Electric sure. furnace is designed In order to assure tribution system external rating 20" _ that even home. (WITH is required if the space between furnace and enclosure is used for return air, 24" MIN. J / For Upflow : ALCOVE When installing accessible only sealed return furnace casing Openings or the ceiling See Figure door, a minimum securely if there ducts must be sealed and the living starting of 200 and be in the outside pass through to prevent walls, air leakage 3. FIGURE 3 • UPFLOW CLOSET CLEARANCE Provisions from shall be made all rooms the circulating and living air supply ply may cause improper to cycle on the limit. to permit the return of circulating air spaces, except the bathroom(s) to inlet of the furnace. heating and Failure may cause to com- the furnace refer instructions away from wall facing or of components. 2. must be available (blower in front of fur- or element removal, fur- FOR ELECTRIC FINGERED SCREW STYLE TAB STYLE 7990-6211 7990-60! 1 7990-6221 7990-6021 14, 7990-6241 14, 14, 7990-6041 14, 6" 7990-626! 7999-6961 7" 7990-6271 7990-6071 8" 7990-628! 7990-6081 11" CLOSET Series), the 2" 10" I part 1" 9" 30" _1 WIDE DOOR TO DIMENSIONS 5" 25-1/2 .... (7900 carefully removal Table 1: DUCT CONNECTOR FURNACES MAX. _ AIR air. See Figure etc.). FLOOR PASS THROUGH FRAME WIDTH easy nace removal, 4" RETURN the you need. Read conveniently servicing 3" 30" the sub- for servicing. nace for future DUCT 1-5/8" MIN., 2-3/8 to eliminate the installation. clearance Two (2) feet of space area. 32" the A minimum of six (6) inches should be maintained between the furnace and closet door when door is used for return is The sup- attached are grilles where before adequate 2. be such throughout 1 will help you in deciding Provide to permit should CONNECTOR) DUCT provided 3. or room which air must be provided. air must be ducted, closet wide by 30 inches closet an outside for return to the furnace into or from 32 inches in a separate through door to the closet. the floor a closet of registers a new duct connector furnace pressure INSTALLATION instructions. partitions the dispressure the static is provided our duct connector Table pres- plate. See Table 3. of the new duct connector Locate the furnace, not exceed heat to the following 1. CLEARANCES wide door is necessary. sq. in. free opening ply and & CLOSET installations, deep with a 30-inch SERIES If you are installing f- FIGURE 2 7900 requirement. number of static so that the static rating FURNACE We have redesigned base does size and placement distribution at a given air flow through on the furnace DOWNFLOW A 6 in. clearance proper to operate must be designed to the furnace shown The number, _ DESIGN 14, 7990-6301 14, 14, 7990-6101 14, 12" 7990-6321 7990-6121 13" 1? 1? 14" NA NA 15" NA NA 1"4,- Indicates connector above or below could be used depending on tolerance in floor to duct dimension. 1"1"- Indicates connector above could be used depending on tolerance in floor to duct dimension. 4,4,- Indicates connector below could be used depending on tolerance in floor to duct dimension. Unitary Products Group 3 035-15266-003 Rev. A (0804) DUCT CONNECTORS (7990 SERIES) These duct connectors are for connecting the furnace to an under the floor supply duct system. The furnace may be installed on combustible flooring without a separate sub-base. DUCT CONNECTORS FOR SCREW ATTACHMENT DUCT CONNECTORS TAB ATTACHMENT FOR 18¼ 18 42_43 4 14_ _14_ o _L _13 _DUCT 11 _ : DUCT W__ _ ........ .................. // m _ i & i , / 2_1/8 ,,, FLOOR CUT*OUT , FOR DUCT CONNECTOR j_FLOOR , _ ( i i SERIES) i _ /_ "!_ _/ , I (7990 ° CEILING CUT-OUT FOR ROOF JACK / "_ ,,': , , I | DIMENSIONS o _° _o CONNECTOR REAR WALL OF ENCLOSURE DIMENSIONS CUTOUT o_o FIGURE 4 11 5 i _ !l i _ I FURNACE ) JN °UTL'NE DUCT CONNECTOR DEPTH SUPPLY OPT ONAL ELECTRIC ...... [_4- DUCT ENTRANCE lq/8 FLOOR FUTURE REFRIGERANT LINE ENTRANCE FIGURE 5 : RECOMMENDED SERIES) 4 FLOOR CUT-OUT (7990 FIGURE 6 : DUCT CONNECTOR (7990 SERIES) DEPTH Unitary Products Group 035-15266-003 Rev.A(0804) LOCATOR BRACKET NAILS, FLAT HEAD SCREWS LOCATOR BRACKET OR STAPLES OR STAPLES _ BENDTABSUNDER DUCT OPENING TO NAILS, FLAT HEAD SCREWS SECURE TO THE SUPPLY DUCT. SCREWS ! FLOOR SUPPLY DUCT FIGURE 7 • SUPPLY DUCT DUCT CONNECTOR ATTACHMENT INSTALLATION CONNECTOR OF SCREW SCREW ATTACHMENT 1. Make floor cut out as shown Determine the depth Place in Figure of the floor duct connector locating bracket to the back edge 4. Apply a water attachment 5. Determine from INSTALLATION When properly duct connector air duct and select See Figure Use screws the supply 8. duct as required duct and insert it through to secure the duct connector to to the supply should duct. If sealant tape the mating flanges and tape must be classified HUD Standard 3280.715, used to provide a better by the applicable National U.L. Standard air seal should or Local was not to pro- Place 4. Determine Products Group bracket 5. cavity from the surface air duct and select which (supplied with the duct connector) of the four positions 5. Mark cut-out location duct connector. 6. Cut out the opening 7. Bend tabs down duct. 8. Secure to the supply through duct and remove 8. the duct. and back up under the supply to the floor with nails, flat or staples. is designed for use on ducts in width. When using the connector there will not be sufficient clearance sides of the duct connector. 181A. Tape In such cases See Figure the duct connector duct and insert it through on the supply the duct connector The duct connector duct by using the from the chart. best centers over the supply the floor cutout. the tabs may sheet be attached metal screws down to 12" on smaller width ducts, to bend the tabs on two to the sides or other suitable of the fasteners. Holes for sheet metal screws are provided in three (3) tabs on each side of the duct connector. If more than 3 tabs need to be used to provide a more the can remaining screws Unitary locating as meeting be approved Code. of the floor duct connector head screws air seal. Duct sealant the depth in Figure of the floor to the top of the supply the duct connector duct. used, the installer NOTE: Determine 3. DUCT to the rear of the floor area for the furnace. aligned with the supply duct, secure the to the floor with nails, fiat head screws or Cut out the opening vide a good 2. of the duct connector. of the four positions ATTACHMENT Make floor cut out as shown 7. to the 1/2" supply TAB (7990 SERIES) appropriate staples. 7. OF TAB (7990 SERIES) 1. the with the duct connector) based duct sealant which from the surface the chart. (supplied best centers over the supply the floor cutout. 6. DUCT 5. cavity of the floor opening. flange DUCT CONNECTOR CONNECTOR of the floor to the top of the supply 3. 8 : ATTACHMENT (7990 SERIES) 2. appropriate FIGURE (7990 SERIES) tabs after drilling secure also the required and air tight be fastened screw connection, to the duct with holes. 5 035-15266-003 Rev.A (0804) PARALLELDUCTSYSTEM TheEBDuctConnector Insert37323716001 maybeusedon EBSeriesElectricManufactured Housing Furnaces where theductsystem runsparallel to thefurnace. SeeFigure9. TheEBDuctConnector Insertshould notbeusediftheduct system runsperpendicular tothefurnace orif theductsystemextends onlyonedirection fromthefurnace. TheDuctConnector Insertcannotbeusedwith 1" and 2" Duct Connectors 7990-6221 Follow (7990-6011, 7990-6211, Upfiow Instruction with the Duct Connector furnace ing the steps Provide 1. conversion listed adequate Before UPFLOW is easily accomplished by follow- below: clearance Conversion, removal for servicing: locate the furnace or partitions and installation 035-20632-001 Two (2) feet of space conveniently to permit easy of components. must be available nace for future servicing nace removal, etc.). (blower in front of fur- or element removal, fur- Insert. 3500-5451" Plate Adapter JRNACE DOO LAYOUT Box and/or Kit are needed 3500-7211" prior to following Upflow steps Assemble the 3500-5451 vided with kit. 2. Remove furnace 3. Remove air filter. 4. Remove strap on the top of the unit, saving Turn entire floor. 6. Remove two (2) screws kit 3500-7211 screws pro- panel. unit upside-down, the top. Obtain FIGURE 9 : DUCT SYSTEM CONFIGURATION filter box per installation the screw for later use. 5. PARALLEL LAYOUT Flange below: 1. and strap PERPENDICULAR TO away from wall facing 2. Kit Installation CONVERSION APPLICATION and ). Accessory provided 7990-6021, FURNACE so the filter box is on the that are on the front of the unit at front panel hanger *. Secure removed angle the hanger from the upflow angle with two (2) from the furance casing See Figure 11. HANGER ANGLE _. FURNACE SEATED AGAINST THE LOCATOR BRACKET SCREW x 2 FIGURE 11 : HANGER ANGLE ATTACHMENT FIGURE 10 : INSTALLATION OF FURNACE INSTALLATION 1. Install the duct flange Secure the front of the furnace Secure holes provided. with two screws See Figure the top of the furnace as shown 9. bracket. at the 10. to a structural member in Figure If installaing Optional position Strap may be moved to any of the holes be pushed equivalent side. method, such Installer as screws may provide through an the casing Standard or Deluxe start collar for the Economy the strap at the top of the furnace. along plate on top of the inverted furnace 12. Air Systems, pro- POS system shipped with 3500-7211" can be used for blend air flex duct installation. Punch the lineset knockout out and screw through located POS, in Step 4 to the top, ceed to Step 10. using the top back of the furnace. 6 8. OF THE FURNACE the Iocator mounting 3. Attach the strap that was removed side or back of the furnace. Remove the front panels and set the furnace onto the duct connector. Slide it back until the rear of the unit engages 2. 7. the start collar under can be used to capture Secure collar over it. Duct connector the casing flange the other and screws edge can provided end of duct connector. to top of furnace. Unitary Products Group 035-15266-003 Rev.A(0804) 10.Flange plateshipped with3500-7211" ismounted tothe furnace witheight(8)screws provided. Two(2)blunt screws arefortheholesinthefrontofthefurnace. See Figure 12. 11.Ifupflowadapter boxkit3500-5451" isnotused,then ouroptional filterbracket isprovided with3500-7211" kit. Thisfilterbracket maybe usedtoretainfilterinsideits original location inthefurnace. 12.Secure thetopofthefurnace toa structural member usingscrews andthestrapontopofthefurnace. The mobile homemanufacturer mayprovide anequivalent strap,ifrequired, tosecure thefurnace. 13.Ifexcessive movement isexpected, thensomeblower support isrecommended. WIRING Furnace for the power diagram and should side through than side of furnace 22 gauge. Power of the unit or through the bottom through the between These in place the furnace entrance, cable will also be no through and the floor. Thus, must be any strain serve in wiring connectors also the located bringing and to relieve connectors and Thermostat enter 1). When of the furnace, to hold wiring wiring. Figure sizes. can the auxiliary of the unit. (See the bottom installed wires supply (or Table 2) for wire wire connect as a on seal additional sealing is Canadian Electrical not required. (Refer to the National breakers. the inside circuit. means JCONNECTOR circuit LINESET branch circuit of the furnace Additionally, breakers requirements. with either These these of disconnecting tect the KNOCKOUT material are equipped amp circuit wiring Code, for wiring The furnaces short DUCT Electrical and local codes NOTE: FLANGE PLATE WITH except See wiring wires smaller USE BLUNT SCREWS) is complete wires. and fuse size. See Table 2 for ground Code (MOUNTED wiring the thermostat one or two 60 breakers in the breakers the power protect event a to the unit. The in the furnace are not meant circuit between wiring of a provide to pro- the furnace and the home's breaker panel. General wire and breaker sizes are shown in Table 2. If sheathed EB SERIES _(UPFLOW FURNACE) cable is used, refer to National Electrical Code, Canadian Electrical Code and local codes for additional requirements concerning supply circuit Electrical Data can be found in Table 4. IMPORTANT rated at 60°C on the furnace FIGURE - All installation on field wiring or higher. Please refer to the wiring or this book for more information. wiring. must be diagrams 12 : BLOWER BRACKET AND DUCT FLANGE ATTACHMENT Table 2: MODELS Single Branch Circuit Service Nominal Circuit Load - AMPS EB20B EB17B EB15B 94.0 84.0 2 L__ads + 1 Ground CK [#! 70.7 64.1 50.7 44.0 #2 #1 #0 #6 #3 #2 #1 #6 #4 #3 #2 #8 #4 #4 #3 #8 #6 #6 #4 #8 #8 #6 #6 #10 70 60 EB23B * Minimum Wire Size (90 ° ) Minimum Wire Size (75 ° ) Minimum Wire Size (60 ° ) Ground Wire Size + Max. Fuse (or C.B.) - AMPS Dual Branci_ £;ircult service Branch Circuit Load - AMPS Branch Circuit Min. - AMPS Minimum Wire Size (90 ° ) Minimum Wire Size (75 ° ) Minimum Wire Size (60 ° ) Ground Wire Size + Max. Fuse (or C.B.) - AMPS C:K.I #1 47.3 125 C:K.I #Z 46.7 C:K.I #1 44.0 110 C:K.I #Z 40.0 90 I EB12BI 90 C:K.I #1 47.3 C:K.I #Z 23.4 C:K.I #1 44.0 C:K.I #Z 20.1 59.2 #6 #6 #4 58.4 #6 #6 #4 55.0 #8 #6 #6 50.0 #8 #8 #6 59.2 #6 #6 #4 29.3 #!0 #!0 #10 55.0 #8 #6 #6 25.2 #!0 #!0 #!0 #10 60 #10 60 #!0 60 #10 50 #!0 60 #10 30 #!0 60 #10 30 EB10B NOT APPROVED * Requires Jumper Bars (P/N 3500-3781") - Dual Supply for U.S. Only. Refer to National Electrical Code. Table 310-16 for Non-Sheathed Conductors. + Refer to National Electrical Code. Table 250-95 for Non-Sheathed Conductor Ground Wire. Unitary Products Group 7 035-15266-003 Rev.A (0804) Table 3: EB SERIES BLOWER PERFORMANCE Low Speed Heating Speed Static Pressure (Inches of WC) .0 .! .2 .3 .4 .5 .6 .7 .8 Models EB10, 12, 15 CFM (STD. Air) 945 936 936 924 915 889 870 813 705 Medium Speed Heating Speed Static Pressure (Inches of WC) .0 .! .2 .3 .4 .5 .6 .7 .8 Models EB17, 20, 23 CFM (STD. Air) 1160 1145 !145 1140 !129 1109 1073 !027 935 Static Pressure Medium High with A-Coil in place (inches of WC) .0 .1 .2 .3 .4 .5 .6 .7 .8 CFM (STD. Air) 1340 1317 1290 !252 1208 1158 1095 !021 876 Static Pressure High with A-Coil in place Table 4: ELECTRICAL MODEL D.O.E. Output OUTPUT CAPACITY (inches of WC) .0 .! .2 .3 .4 .5 .6 .7 .8 CFM (STD. Air) 1573 !534 1490 !435 1369 !309 1237 1135 10!9 DATA NUMBER EB23B EB20B EB17B EB15B EB12B EBIOB 56,000 51,000 39,000 34,000 240 VAC 60 Hz. 1 Phase BTU 77,000 67,000 KW 22.6 19.6 230 VAC 60 Hz. 1 Phase BTU 7! ,000 61,000 KW 20.8 17.9 220 VAC 60 Hz. BTU 65,000 57,000 KW !9.1 16.7 KW 21.6 19.2 16.0 14.4 11.2 9.6 AMPS 90.0 80.0 86.7 60.0 46.7 40.0 50.7* 44.01 1 Phase EIement Capacity @ 240 VAC 16.4 15.0 11.4 52,000 47,000 36,000 31,000 15.2 13.8 !0.6 9.1 48,000 43,000 33,000 29,000 14.1 12.6 9.7 8.5 4.0 Maximum Motor AMPS @ 240 V. Circuit Load AMPS @ 240 V. CKT 1 47.3 44.0 47.3 44.0 CKT 2 46.7 40.0 23.4 20.0 1. Approved for Single Branch Circuit Service Only Casing or Cabinet must be Permanently Grounded in Accordance Models for EB23B, nected to a single or dual branch These units shipped power supply 8 are EB20B, connections. EB17B from 10.0 and circuit. the For single EB15B (See factory power may be con- Table 2.) set up for supply dual with National Electrical Code or other Applicable Codes. tions, jumper bars (P/N available from the factory. with jumper bars in place. 3500-378P*) are required Model for EB12B is factory and are shipped connec- Unitary Products Group 035-15266-003 Rev.A(0804) SEQUENCERS CIRCUIT BREAKERS II / ,L THERMOSTAT WIRES / 3500-378P* JUMPER BARS (FOR SINGLE BRANCH CIRCUIT J SERVICE) @ NOTE: AS SHIPPED, THE JUMPER BAR ASSEMBLY IS SET-UP FOR BOTTOM ENTRY. FOR SiDE ENTRY, THE TOP LUG CAN BE REMOVED AND RE-POSITIONED, AS SHOWN, TO PROVIDE PROPER WIRE BENDtNG CLEARANCES, J TRANSFORMER ® J LIMIT SWITCHES L ® ® _ OI } _GROUND O0 LUGS @ FIGURE 13 : CONTROL BOX THERMOSTAT The adjustable _WARNING For personal safety power at the household the "OFF" furnace circuit be sure breakers to turn before or maintenance operations. should never any requires opening Furnace is equipped field wiring pleted, (See connection. shield electrical electric Figure when electrical box and attempting In some at any Homeowners maintenance with a protective When field which shield wiring to prevent using furnace over is comhazard disconnect. 14.) which of heat anticipator This cases case eliminating setting in the thermostat should the thermostat no Amp. be should checked is pre-set at the may be a "self-setting" setting will be found the need for any field Thermostat box door. must be replaced shock the service service perform 0.4 Amps. installation INSTALLATION be located time at of type in on the thermostat, adjustment. on an inside wall in an open area to more closely regulate average room air, preferably, where there is air movement back to furnace. Care should be used to locate ings, lights, Thermostat thermostat floor. This is sometimes If a condenser Thermostat contacts tems. away from hot air discharge with called its own with this furnace, to prevent the comfort Transformer interconnection of Class to make sure it will operate Maintenance and operating accompanying Give the customer zone. shares use a thermostat Cycle furnace envelope open- etc. Locating height of thermostat is important. should be located 52 to 66 inches above the instructions a Heat/Cool with isolating II 24 Volt Sys- correctly. are in the customer the furnace. envelope to the home owner. CIRCUIT BREAKERS BLOWER ELECTRIC //PANEL J FIELD WIRING PROTECTIVE SHIELD FIGURE 14 : FIELD WIRING SHIELD Unitary Products Group 9 035-15266-003 Rev.A (0804) CAUTION When using separate thermostats, interlock system must be provided taneous operation of the furnace Simultaneous operation heating, equipment Figures 15 and 16.) Do not connect outdoor unit is instafled. can damage Yellow a HEATING THERMOSTAT thermostat to prevent simul- and air conditioner. result in coach and energy wire COOLING THERMOSTAT over- waste. to thermostat (See until DOUB %L o% ,TCH an TO AiR CONDITIONER TO FURNACE FIGURE 15 : THERMOSTAT WIRING All furnaces The EB*B* Furnaces are A/C ready. installations should include a minimum of four conductor wiring to accommodate future air conditioning installations, thermostat THERMOSTAT WiRiNG SCHEMATIC FOR: BLEND AIR AND FURNACE RED NOT STANDARD OR DELUXE BLEND AIR CONTROL BOX FACTORY INSTALLED Z uJ uJ Four-conductor wire is required for thermostat connection, Attach the 4 low voltage wires extending from the control box as follows: 1. RED wire from Furnace to thermostat RED wire. © 2. WHITE wire from Furnace to thermostat WHITE wire. 3. GREEN wire from Furnace to thermostat GREEN wire. WIRES FROM FURNACE 4. BLACK wire from Furnace to condensing 5. Thermostat YELLOW wire to condensing unit contactor. unit contactor. FIGURE 16 : THERMOSTAT WIRING OPTIONAL AIR CONDITIONING ACCESSORIES This furnace system up to 3-1t2 downflow adding Failure could to result install this in damage insulation sonal injury. Liability and warranty facturer could also be void. 10 and coil to equipment from shelf and/or is already to add-on tons. Insulation or 3500-8961" on such equipped air conditioning remote with a blower and control up to 4 tons and heat pump and coil shelf for upflow) air conditioning kit (3500-8941" must be installed for when systems. kit per- the manu- Unitary Products Group 035-15266-003 Rev.A(0804) HIGH PERFORMANCE BLOWER ACCESSORY All EB furnaces trol system PACKAGE pump around openings in the coil sheff should Use some the line sets, drain moldable compound the area. Failure formance and premature WIRING would hoses and other be sealed or caulking to do so may result compressor in loss air tighL than the up to 5-tons, blower and heat pump of per- tions tion. packed with etc. Please would package for more air Acces- insulation, refer to the installation the accessory package deliver up to 4-tons. blower, heat more the furnace blower package (3500-7901")includes trap, clamps, failure. inside blower with an accessory conditioning package and production This accessory shelf, and con- up to 4-tons is to achieve have to be replaced to seal with a blower If the requirement 3500-7901". sory equipped air conditioning up to 3 1/2-tons. than specified CAUTION I All areas are already to add-on coil instrucinforma- DIAGRAMS CONTROL 4-SPEED BLOWER EB SERIES FURNACES Z BOX HEAT/COOL T'STAT BLEND A]i COND UNIT CONTACTOR A A 2 SPADE (]NSUL) TERMINALS USED WHEN CHANGING SPEEDS BLOWER TRANSFORMER CIRCUIT #1 BREAKER [_ 60 Hz I PHASE t 24° VAC GND LUG MODEL: EB10B SINGLE BRANCH CfRCUfT SERVICE ELEMENTS LIMIT SWITCHES 240 VAC - 60 Hz - 1 PHASE NOTE:IF ANY OF THE ORIGINAL WIRE SUPPLIED WITH THIS UNIT MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE 105°C THERMOPLASTIC OR ITS EQUIVALENT. FACTORY WIRING SHOWN SOLID, FIELD WIRING SHOWN BROKEN, WIRING MUST CONFORM TO LOCAL CODES APPROVED FOR CU CONDUCTORS ONLY, FIGURE D,O,E, OUTPUT CAPACITY - BTU MAX, MOTOR-FLA SINGLE BRANCH CIRCUIT SERVICE NOMINAL CIRCUIT LOAD-AMPS 34,000 4,0 2 LEADS + 1 GROUND 44,0 WIRE SIZE (75/' C) COPPER #6 WIRE SIZE (60 ° C) COPPER #6 MAX, FUSE SIZE (OR CB) -AMPS 60 17 : EB10B WIRING DIAGRAM Unitary Products Group 11 035-15266-003 Rev. A (0804) CAPACITOR BLEND AIR CONTROL BOX 4-SPEED BLOWER EB SERIES FURNACES HEAT/COOL T'STAT CONDUNIT CONTACTOR A A E13 2 SPADE (INSUL)TERMINALS USED WHEN CHANGING SPEEDS GRN WHT FUSE BLK BLOWER RELAY BLK CIRCUIT #1 BREAKER YEL 240 VAC • 60 Hz I PHASE GND MODEL: EB12B LUG SINGLE BRANCH C]RCUIT SERVICE ELEMENTS NOTE:IF ANY OF THE ORIGINAL WIRE SUPPLIED WITH THIS UNIT MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE 105°C THERMOPLASTIC OR ITS EQUIVALENT. FACTORY WIRING SHOWN SOLID, FIELD WIRING SHOWN BROKEN, WIRING MUST CONFORM TO LOCALCODES APPROVED FOR CU CONDUCTORS ONL_ LIMIT SWITCHES 240 VAC - 60 HZ - 1 PHASE 3,O,E, OUTPUT CAPACITY - BTU V_AX, MOTOR-FLA BINGLE BRANCH 31RCUIT SERVICE qOMINAL CIRCUIT LOAD-AMPS 39,000 4,0 2 LEADS + 1 GROUND 50,7 NIRE SIZE (75 ° C) COPPER #6 NIRE SIZE (60 ° C) COPPER #4 V_AX, FUSE SIZE (OR CB) -AMPS 7O FIGURE 18 : EB12B WIRING DIAGRAM 12 Unitary Products Group 035-15266-003 Rev.A(0804) CAPACfTOR 4-SPEED BLOWER EB SERIES FURNACES BLEND AIR BOX CONTROL _F_ z m _ v MODEL: EB15B IT CONTACTOR CIRCU]T #1 BREAKER 2 SPADE (INSUL) TERMINALS USED WHEN / GRN WHT TRANSFORMER__ ILINE, £_ RED FUSE _ _ F BLK RED SINGLE BRANCH CIRCUIT SERVICE 2401 60pHAsEVACHz BREAKER [] CIRCUIT #2 y[ GND , YEL CRCL h. L_ OR_',_ER \ GND LUG -1 LUG C,RCO,T_ 24EOVAzC DUAL BRANCH CIRCUIT SERVICE C'RDU'T% LO0 L _ = _A L ^ ^ ^^ ^_1_ _VVVVVV4_RI ELEMENTS LIMIT SWITCHES NOTE: IF ANY OF THE ORIGINAL WIRE SUPPLIED WITH THIS UNIT MUST BE REPLACED. IT MUST BE REPLACED WITH TYPE 105°C THERMOPLASTIC OR ITS EQUIVALENT. FACTORY WIRING SHOWN SOLID, FIELD WIRING SHOWN BROKEN, WIRING MUST CONFORM TO LOCAL CODES APPROVED FOR CU CONDUCTORS ONLY, D.O.E. OUTPUT CAPACITYMAX. MOTOR-FLA SINGLE BRANCH CIRCUIT SERVICE NOMINAL CIRCUIT BTU $ LOAD-AMPS WIRE SIZE (75 ° C) COPPER WIRE SIZE (60 ° C) COPPER MAX. FUSE SIZE (OR CB) - AMPS DUAL BRANCH CIRCUIT SERVICE BRANCH CKT. LOAD-AMPS BRANCH CKT. MIN. AMPACITY WIRE SIZE (75 ° C) COPPER WIRE SIZE (60 ° C) COPPER MAX. FUSE SIZE (OR CB) - AMPS $ REQUIRES JUMPER 51,000 4.0 2 LEADS + 1 GROUND 64.0 #4 #3 9O 4 LEADS + 2 GROUNDS CKT #1 - CKT #2 44 20.1 55 25.2 #6 #10 #6 #10 60 30 BARS (PIN 3500-378/*) FIGURE 19 : EB15B WIRING DIAGRAM Unitary Products Group 13 035-15266-003 Rev.A (0804) MODEL: EB17B 2 SPADE (INSUL) TERMINALS USED CHANGING SPEEDS WHEN BLOWER CIRCUIT ..... I _ #1 BREAKER TJ L _ [_ _] UND LUG ' I d PHASE RED - f# OK _---,._-_ 1 ._r9 240 0 BREAKER L_ DUAL BRANCH CIRCUIT SERVICE VAC 60 Hz [_ • ELEMENTS CIRCUIT1 240 VAC BREAKER | LIMIT SWITCHES NOTE: IF ANY OF THE ORIGINAL WIRE SUPPLIED WITH THIS UNIT MUST BE REPLACED. IT MUST BE REPLACED WITH TYPE 105°C THERMOPLASTIC OR ITS EQUIVALENT. FACTORY WIRING SHOWN SOLID, FIELD WIRING SHOWN BROKEN, WIRING MUST CONFORM TO LOCAL CODES APPROVED FOR CU CONDUCTORS ONLY, GND I PHASE LUG-- 240 VAC - 60 Hz - 1 PHASE D.O.E. OUTPUT CAPACITY - BTU MAX. MOTOR-FLA SINGLE BRANCH $ CIRCUIT SERVICE NOMINAL CIRCUIT LOAD-AMPS WIRE SIZE (75 ° C) COPPER WIRE SIZE (60 ° C) COPPER MAX, FUSE SIZE (OR CB) - AMPS DUAL BRANCH CIRCUIT SERVICE BRANCH CKT. LOAD-AMPS BRANCH CKT. MIN. AMPACITY WIRE SIZE (75 ° C) COPPER WIRE SIZE (60 ° C) COPPER MAX, FUSE SIZE OR CB) - AMPS SREQUtRES JUMPER 56,000 4.0 2 LEADS + 1 GROUND 70.7 #3 #2 9O 4 LEADS + 2 GROUNDS CKT #1 - CKT #2 47.3 23.4 59.2 29.3 #6 #10 #4 #10 60 30 BARS (P/N 3500-378/*) FIGURE 20 : EB17B WIRING DIAGRAM 14 Unitary Products Group 035-15266-003 Rev.A(0804) BLENDAIR CONTROL BOX HEAT/COOL T'STAT MODEL: EB20B CONTACTOR A[Z_ CIRCUIT #1 BREAKER ,A SINGLE BRANCH CIRCUIT SERVICE 2 SPADE (INSUL) TERMINALS USED WHEN CHANGING SPEEDS 124OVA c I PHASE CIRCUIT #2 BREAKER [_ GND CIRCUIT #1 F_ GND LUG 1 CfRCUff 240 VAC 60 Hz I PHASE LUG DUAL BRANCH CIRCUIT SERVICE CIRCU]T 2 240 VAC CIRCU]T #2 r_ BREAKER GNDLUG ] 60 Hz 1 PHASE 240 VAC ELEMENTS UMIT SWITCHES NOTE: IF ANY OF THE ORIGINAL WIRE SUPPLIED WITH THIS UNIT MUST BE REPLACED. IT MUST BE REPLACED WITH TYPE 105°C THERMOPLASTIC OR ITS EQUIVALENT. FACTORY WIRING SHOWN SOLID. FIELD WIRING SHOWN BROKEN. WIRING MUST CONFORM TO LOCAL CODES APPROVED FOR CU CONDUCTORS ONLY. - 60 Hz - 1 PHASE D.O.E. OUTPUT CAPACITY - BTU MAX. MOTOR-FLA SINGLE BRANCH $ CIRCUIT SERVICE NOMINAL CIRCUIT LOAD-AMPS WIRE SIZE (75 ° C) COPPER WIRE SIZE (60 I, C) COPPER MAX, FUSE SIZE (OR CB) - AMPS DUAL BRANCH CIRCUIT SERVICE BRANCH CKT. LOAD-AMPS BRANCH CKT. MIN. AMPACITY WIRE SIZE (75 ° C) COPPER WIRE SIZE (60 I, C) COPPER MAX, FUSE SIZE (OR CB) - AMPS $ REQUIRES JUMPER 67,000 4.0 2 LEADS + 1 GROUND 84.0 #2 #1 110 4 LEADS + 2 GROUNDS CKT #1 - CKT #2 44.0 40 55 50 #6 #8 #6 #6 60 50 BARS (P/N 3500478/*) FIGURE 21 : EB20B WIRING DIAGRAM Unitary Products Group 15 035-15266-003 Rev.A (0804) CAPACITOR BLENDAIR CONTROL 4-SPEED BLOWER EB SERIES FURNACES BOX HEAT/COOL T'STAT MODEL: EB23B CONTACTOR A CIRCUIT #1 CIRCUIT #2 SINGLE CfRCUiT A BRANCH SERVICE GRN 2 SPADE (INSUL) TERMINALS USED WHEN CHANGING SPEEDS RELAY BREAKER _] j GND CIRCUIT #1 BREAKER LUG Z [_ CIRCUIT 1 240 VAC 60 Hz I PHASE DUALBRANCH CIRCU]T SERVICE CIRCUIT 2 240 VAC 60 Hz I PHASE GND LUG 240 VAC - 60 Hz - 1 PHASE D.O.E. OUTPUT CAPACITY - BTU MAX, MOTOR-FLA SINGLE BRANCH :I: CIRCUIT SERVICE NOMINAL CIRCUIT LOAD-AMPS ELEMENTS L]MIT SWITCHES NOTE:IF ANY OF THE ORIGINAL WIRE SUPPLIED WITH THIS UNIT MUST BE REPLACED. IT MUST BE REPLACED WITH TYPE 105°C THERMOPLASTIC OR ITS EQUIVALENT. FACTORY WIRING SHOWN SOLID. FIELD WIRING SHOWN BROKEN. WIRING MUST CONFORM TO LOCAL CODES APPROVED FOR CU CONDUCTORS ONLY. WIRE SIZE (75 ° C) COPPER WIRE SIZE (60 I' C) COPPER MAX, FUSE SIZE (OR CB) - AMPS DUAL BRANCH CIRCUIT SERVICE BRANCH CKT. LOAD-AMPS BRANCH CKT. MIN. AMPACITY WIRE SIZE (75 ° C) COPPER WIRE SIZE (60 I' C) COPPER MAX, FUSE SIZE (OR CB) - AMPS :I:REQUIRES JUMPER 77,000 4.0 2 LEADS + 1 GROUND 94.0 #1 #0 125 4 LEADS + 2 GROUNDS CKT #1 - CKT #2 47.3 48.7 59.2 58.4 #6 #6 #4 #4 60 60 BARS (P/N 3500-378/*) FIGURE 22 : EB23B WIRING DIAGRAM 16 Unitary Products Group 035-15266-003 Rev.A(0804) REPAIR PARTS LIST MODELS ii iii IIS E8108 EB128 E8158 E8178 iii iii uI E82OB E823B " °r [ v J Unitary Products Group 17 035-15266-003 Rev. A (0804) ITEIV 1 2 DESCRIPTION Thermostat (Heat!Cool) Front Panel EB10B EBI2B EBISB 025-38746-000 025-38746-000 025-38746-000 3500-1751/B 3500-1581 3500-159! 1214-2511 1214-2521 3500-1751/B 3500-1581 3500-159! 1214-2511 1214-2521 3 Filter (16 x 20 x 1) Filter (2o x 2o x 1) (Front Return Panel) 3500-!751/B 3500-1581 3500-1591 12!4-2511 12!4-2521 4 5 Support Angle Cover, Electric Box 3500-1861 3500-1861 3500-1861 3500-2351/A 3500-2361/A 3500-2361/A 6 Cover (Service Entrance) 7 8* Sub-base (Optional) Sub-base (M10)(Optional) 3500-!271 3500-1071/B 3500-1271 3500-1071/B 3500-1271 3500-1071/B 3500-5221 3500-5221 3500-522! 9 Blower Motor (For furnaces produced before 2/99) 1488-243P/A 1488-243P/A 1468-243P/A 10 Blower Motor (For furnaces produced after 2/99) 024-27651-000 024-27651-000 024-27651-000 11 12 Capacitor (7.5MFD/370V) !499-4461 1499-4461 1499-446! 3110-3301 3110-3301 3110-3301 13 Relay Motor Mount Assembly 373-19831-09! 373-19831-001 373-19831-001 14 15 Blower Wheel 1472-2831 1472-2831 1472-2831 Limit Baffle (For furnaces produced before 3/98) Heater Element (For furnaces produced before 3/98) 3500-!29 3500-!01 3500-101 (9.6Kw) 3500-4101 (11.2Kw) 3500-412! (4.8Kw) & (9.6Kw) 3500-405! & 3500-419! Front Panel (Front Return 4-Ton) Front Panel (Front Return 5-Ton) 16" 17 (! PC) (Kit) 18 Heater Element 19 20 Transformer Sequencer 21 Bracket (Circuit Breaker) 22 Limit Switch (For furnaces produced before 3/98) 23 Circuit Breaker (1 Req'd) Circuit Breaker (2 Req'd) 24 (See Note 3) (See Note 2) 26 27 Drain Tube (See Note 1) 28 Coil Shelf Coil Shelf Panel Insulation, Cover Panel 29 30 31" Condensate (11.2Kw) 3500-412 P/A 3300-3861 3390-3861 3110-3571 3!10-3571 3500-!28 3500-!28 3500-!28 2 ea. 7142-3091 2 ea. 3500-3121 3 ea. 3500-3151/A (240/24V-40A) Buss Bar Ground Lug (Large) Ground Lug (Small) 25 (9.6Kw) 3500-419 P/A Trap (Open 150, Close 110) 3500-377P/A (Open150, Ctose120) (4.8Kw) & (9.6Kw) 3500-405P/A& 3500-410P/A 3390-3861 3!10-357! (Open 150, Close 110) 3500-377P/A 3500-377P/A 3500-378P 3500-378P 3500-378P 1216-231 1216-231 1216-231 12!6-229 029-22!84-001 3240-3051 029-22!84-001 3240-3051 029-22184-001 3240-3051 (See Note 1) (See Note 1) 3500-174 3500-174 3500-174 3500-!71 3500-171 (See Note !) 9!0-69111-001 (See Note 1) 9!0-6911!-001 3500-171 010-6911!-001 32* See Page 20 Field Fix Kits 33* 34* 35* 36* NOTE: Wiring diagram Fuse 035-!5274-001 925-32746-026 035-!5275-001 925-32746-026 035-!5276-001 025-32746-026 *Not Shown Major components and suggested stocking items are shown with shaded item number. --- Not applicable to specified model. All parts with three digit suffix numbers are "Special Order" parts avaitabitity and require extra time for detivery 1 Not Standard with furnace, 2 Standard on EB12B. 18 contained in accessory These parts are subject to factory kit no. 3500-8941. Unitary Products Group 035-15266-003 Rev.A(0804) ITEM 1 2 3 DESCRIPTION Thermostat (Heat/Cool) Front Panel Front Front Filter Filter Panel (Front Return 4-Ton) Panel (Front Return 5-Ton) (16 x 20 x 1) (20 x 2o x 1) (Front Return Panel) 4 5 Support Angle Cover, Electric Box 6 Cover (Service Entrance) 7 Sub-base (Optional) 8 9 Sub-base (M10) (Optional) Blower Motor (For furnaces produced 10 before 2/99) Blower Motor (For furnaces produced after 2/99) 11 12 EB17B EB20B EB23B 025-38746-000 3500-!751/B 3500-!581 3500-!591 025-38746-000 3500-1751/B 3500-1581 3500-1591 025-38746-000 3500-1751/B 3500-!581 3500-!59! 1214-2511 12!4-2521 1214-2511 12!4-2521 1214-2511 1214-252! 3500-186! 3500-236!/A 3500-1861 3500-236!/A 3500-1881 3500-2361/A 3500-1271 3500-1271 3500-127! 3500-!071/B 3500-5221 3500-1071/B 3500-5221 3500-1071/B 3500-5221 1468-243P/A 1468-243P/A 1488-243P/A 024-27651-000 024-27651-000 024-27651-000 Capacitor (7.5MFD/370V) !499-4461 1499-4461 1499-446! Relay 3110-3301 3!10-3301 3110-3301 373-19831-001 373-19831-001 373-19831-001 13 Motor Mount Assembly (1 PC) (Kit) 14 15 Blower Wheel 1472-283! 1472-2831 1472-2831 Limit Baffle (For furnaces produced before 3/98) Heater Element (For furnaces produced before 3/98) 3500-!29 3500-!29 3500-129 (4.8Kw) & (11.2Kw) 3500-4051 & 3500-4121 2 Ea.(9.6Kw) 3500-4101 (10.4Kw) & (11.2Kw) 3500-4111 & 3500-4121 (5.6Kw) & (!0.4Kw) 3500-406P/A & 3500-411P/A 2 Ea. (9.6Kw) 3500-410P/A (10.4Kw) & (11.2Kw) 3500-411P/A & 3500-412P/A 16 17 18 Heater Element 19 20 Transformer Sequencer 21 Bracket (Circuit Breaker) 22 Limt Switch (For furnaces before 3/98) produced Circuit Breaker Buss Bar (See Note 2) 23 24 25 26 27 28 29 30 31" (See Note 3) (240/24V-40A) (2 Req'd) Ground Lug (Large) Ground Lug (Small) Drain Tube Condensate (See Note 1) (See Note 1) Trap Coil Shelf (See Note 1) Coil Shelf Panel Insulation, Cover Panel (See Note 1) (See Note !) 3300-3861 3300-3861 3300-3861 3115-3571 3500-128 3!20A3571 3500-!28 3129A3571 3500-128 3 ea. 7142-3091 (Open 158, Close 110) 3500-377P/A 4 ea. 7142-3091 (Open150, Close 110) 3500-377P/A 4 ea. 7142-3091 (Open 150, Ctose 110) 3500-377P/A 3500-378P 1216-231 3500-378P 12!6-231 3500-378P 1216-231 1216-229 029-22!84-001 12!6-229 029-22!84-001 1216-229 029-22184-001 3240-3051 3500-!74 3240-3051 3500-174 3240-3051 3500-174 < 3500-17!1 3500-1711 3500-!71! < 010-691!1-001 010-691!1-001 0!0-6911!-001 < 32* See Page 20 For Field Fix Kits 33* 348 35* 36* NOTE: Wiring diagram Fuse 035-!5277-001 025-32746-026 035-!5278-901 025-32746-026 035-15279-001 025-32746-026 *Not Shown Major components and suggested stocking items are shown with shaded item number. --- Not applicable to specified model. All parts with three digit suffix numbers are "Special OrdeP parts. These parts are subject to factory availability and require extra time for delivery 1 Not Standard with furnace, 2 Standard on EB12B. Unitary Products Group contained in accessory kit no. 3500-8941 19 FIELD FIX KIT FOR EB12 FIELD (A&B) MANUFACTURED FIX KT 3500-7121 1995 CONTAINS: DESCRIPTION PART NO. 31" ! Each Limit Baffle 3500-101 32* 2 Each Limit Switch 3500-3121 FIX KIT FOR EB15 FIELD (A&B) MANUFACTURED FIX KT 3500-7151 PRIOR TO AUGUST 1995 CONTAINS: ITEM DESCRIPTION PART NO. 33* ! Each Limit Baffle 3500-101 34* 2 Each Limit Switch 3500-3151/A Subject to change without notice. Printed in U.S.A. Copyright t-: by York International Corp. 2004. All rights reserved. Group TO AUGUST ITEM FIELD Unitary Products PRIOR Supersedes: RO. Box 19014 035-15266-003 035-15266-002 Rev. A (0804) Rev. D (0304) Wichita KS 67204-9014
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 20 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Wed Aug 18 04:15:13 2010 Author : Title : Subject :EXIF Metadata provided by EXIF.tools