Cadi Scientific TSS900 ThermoSensor User Manual
Cadi Scientific Pte. Ltd. ThermoSensor
User Manual
TSS-800/900 ThermoSENSORTM Wireless Temperature Sensor User Guide Cadi Scientific Pte Ltd Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. COPYRIGHT Specifications are subject to change without notice. Copyright © 2003 Cadi Scientific Pte Ltd. All rights reserved. Cadi Scientific Pte Ltd 1003 Bukit Merah Central #04-40 Singapore 159836 Singapore http://www.cadi.com.sg Cadi Scientific Pte Ltd Introduction The TSS-800/900 ThermoSENSORTM is a wireless temperature sensor for measuring a patient’s body temperature. It is part of the SmartSense Wireless Integrated Sensing System – a system designed for monitoring of vital signs, tracking of the location of people and equipment, contact-tracing between people, and providing alert notification of people or equipment that has arrived at designated locations. The ThermoSENSORTM is to be attached to patients’ body, at the lower abdomen area, with the use of a comfortable and hypoallergenic dressing, such as the 3M Tegaderm, to continuously measure patient’s body temperature. Every 30 seconds, the sensor will take a temperature measurement and transmits the measured temperature to the SMN-800/900 SmartNODE. Cadi Scientific Pte Ltd Features • • • • • • Each ThermoSENSORTM has a unique ID Measures patient’s body temperature by contact with patient’s skin Wirelessly transmits ID and temperature data to the SMN-800/900 SmartNODE Sensor is activated or deactivated using SSW SmartSWITCH Sensor has a lifespan of up to 12 months of continuous usage (based on 30 seconds transmit interval) Water-resistant enclosure that allows cleaning using water or alcohol Cadi Scientific Pte Ltd Instruction for use Identify an area for ThermoSENSOR™ to be pasted. 1. Place 3 fingers down from the navel. Refer to diagram. 2. Place the first layer of adhesive dressing about half the distance from the center to the side of the body. Refer to diagram. 3 fingers down 3. Place ThermoSENSOR™ on another layer of adhesive dressing*. The second layer of dressing should be pasted over the front of the sensor. Do not paste the dressing on the metal part of the sensor. You may use any suitable medical adhesive dressing e.g. 3M tegaderm 4. Place ThermoSENSOR™ (with the second layer of adhesive dressing) over the first layer of adhesive dressing. Cadi Scientific Pte Ltd 5. For cleaning before use, wipe the ThermoSENSOR™ with an alcohol swab. • Cadi Scientific recommends 3M Tegederm dressing for use with the ThermoSENSOR as it has been tested to have no adverse effect on the user/ThermoSENSOR. 0434 Medical Device Safety Service, GmbH Schiffgraben 41, 30175 Hannover, Germany CADI SCIENTIFIC 1003 Bukit Merah Central, #04-40, Singapore 159836 Tel: (65) 62762676 Fax: (65) 62766216 Email: info@cadi.com.sg URL: www.cadi.com.sg Made In Singapore Cadi Scientific Pte Ltd Specifications Technical Data General Unique Sensor ID Thermistor accuracy 24 bits +/- 0.2oC (32.0 to 42.0oC) Transmission Rate Data transmission rate Every 30 seconds (on average) RF RF Frequency Transmit Power US (TSS-9xx): 919.8MHz or 925MHz Europe (TSS-8xx): 868.4MHz Less than -2dBm Power Source Power source Estimated battery life Internal 3V lithium cell 12 months (@30 sec transmit interval) Environment Operating temperature range Water resistant 10 – 50oC Yes Physical Dimension Weight Compliance Certification RF Compliance EMC Compliance 36mm DIA, 11.6mm HT 12g CE, FCC ETSI EN 300 220 ETSI EN 301 489
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 7 Producer : GPL Ghostscript 8.15 Create Date : 2007:10:22 18:18:15 Modify Date : 2007:10:22 18:18:15 Title : Microsoft Word - TSS-800 900 ThermoSENSOR User Guide.doc Creator : PScript5.dll Version 5.2 Author : nghoncheongEXIF Metadata provided by EXIF.tools