Cal Comp Electronics CHYN4590 Bluetooth Headset User Manual Revised

Cal-Comp Electronics (Thailand) Co. Ltd. Bluetooth Headset Revised

UserManual.wiki >

Cal Comp Electronics >

CHYN4590 User Manual

Revised user manual

Putting On the Headset  Put on the Headset with the ear clip behind your ear.  Ensure the microphone is pointing toward your mouth.

Charging The Headset comes with a rechargeable battery included. The battery is not fully charged when it is new. For first time use, insert the adaptor into the Headset to charge until the indicator light turns green.  It takes 1-1.5hours to fully charge the battery.  To indicate that the Headset runs on low power, the Headset indicator light flashes red when the Headset is on.  When the Headset is turned off during the process of charging, the indicator light shows a steady red light, and flashes red when the Headset is on.  When the headset is turned off once the battery is fully charged, the indicator shows a steady green light, or shows green light if the Headset is on.  After battery fully charged, do not recommend charging again while indicator light flashes green. Which Charger Can I Use Please use MOTOROLA travel charger to the Headset. How to Charge the Battery . Connect the adaptor into the Headset as shown in the picture. Gently press the adaptor until it clicks into place. Volume Adjustment Listening volume adjustment Headset listening volume can be adjusted during a call. To adjust the listening volume  To turn down the volume, slide and return the Headset button SW1.  To turn up the volume, slide and return the Headset button SW2. Note: The orientation of the volume button must be changed when you change the ear on which the Headset

is worn. Making and Receiving Calls Once the Headset is successfully paired with your phone, you can use the Headset to make and receive calls, provided that the Headset is on and operated within up to 10m/ 30ft. with no solid obstructions of the phone. The Headset can be used with voice dialing if your phone supports this feature. For detailed operation on voice control, please refer to your phone’s user’s manual. The Headset light indicator will flash slower during an ongoing call. The Headset button has following functions:  make a call (by using voice control and redial)  receive a call  terminate a call  transfer the sound from the phone to the Headset The following is for user’s reference should you be using the Headset with a built-in Bluetooth phone. Making Calls Using voice dialing to make a call 1. Be sure the phone and the Headset are power on and are within close proximity to each other. Single click ”SW3” on the Headset. 2. Once a beep is heard, voice dial as you normally would. 3. Press “SW3” button on the Headset to end the call, or press the NO key on the phone. How to redial last phone call Be sure the phone and the Headset are power on and are within close proximity to each other. Press ”SW3” on the Headset for a few seconds to automatically redial last phone call. Should the phone not supporting voice dialing, you can also make a call using the phone’s keypad or phone book Using the phone keys to make a call 1. Ensure the Headset and the phone is turned on and within 10m/ 30ft of each other. 2. Enter the number as you normally would. 3. With a built-in Bluetooth mobile: Once the call has been connected, press the Headset button “SW3” to transfer the sound to the Headset. 4.

Press the Headset button “SW3” or the NO key to end the call. Answering Calls  When the Headset rings, press the button “SW3” on the Headset to answer a call.  Single click “SW3” on the Headset or the NO key to end the call.  Press ”SW3” on the Headset for a few seconds or the NO key to refuse all the phone calls. To answer a second call During a conversation, you can answer a second incoming call by pressing the “SW3” for a few seconds, and you can still use the Headset for talking and listening. Transferring the sound from phone to Headset You can still transfer the sound to the Headset if you make a call without using it. Make sure the Headset is on and within close range to the phone. Transferring calls Calls can be transferred from the cell phone to the Headset and from the Headset to the cell phone. Transferring the sound from phone to Headset 1. With a Bluetooth phone, press the button on the Headset to transfer the sound to the Headset. 2. If you turn on the Headset after receiving the phone call, you could press “SW3” to transfer the sound to the Headset. Transferring sound from Headset to phone Use with a built-on Bluetooth phone. During an ongoing call, scroll to Ongoing Call, choose “Yes”, then select “Transfer Call” and press “Yes” to confirm the transfer.

Additional information Troubleshooting This section lists some problems that you might encounter while using your Headset. The Headset Indicator Light Flashes Red This indicates that the Headset is running on low battery and has limited talk time and standby time left. Charge the Headset for approximately 1 to 1.5 hours. No Sound Contact Between Headset and Other Device In order for the Headset and the device you are using to recognize one another, they ought to be paired. Make sure the Headset and the device you are using with are no more than 10 m. /30 ft. apart, so they are within operable range. No Indication of Charging is Shown For the Headset battery that is empty, or has not been used for a long time, it may take several minutes for the indicator to show charging status (a steady red light). Guidelines for Safe and Efficient Use Note: Read this information before using your Bluetooth Headset.

Product Care and Maintenance Please read the following to get the most out of your sophisticated Bluetooth Headset about product care, safe and efficient use. For any queries about any exceptions when using Bluetooth equipment, due to national requirements or limitations, please visit www.bluetooth.com. Product Care • Use of non-Motorola original accessories may result in performance deterioration, product damage, injury, or electronic shock, and warranty termination. • Do not attempt to disassemble your Headset, as it does not contain any components serviceable or repairable by consumers. • Do not paint your product as the paint could prevent normal use. • Do not place the Headset in a dusty area, and only use soft cloth to clean your Headset. • Do not allow children to play with your Headset, as they might injure themselves or others as well as damaging the Headset. • When the Headset is not in use, always place it in its case. • Do not place the Headset in extreme hot or cold temperature if the Headset will not be used for a while. Potentially Explosive Atmospheres When surrounded by possible explosive atmosphere, turn off the electronic device as it may generate sparks which can cause an explosion or fire. Explosive atmosphere may include gas stations, fuel or chemical storage facilities, and in environment where metal powders, grain, dust are contained in the air. For safety reasons, do not carry or store flammable goods such as gas, liquid in your vehicle compartment containing an electronic device. Power Supply • Power supply must be connected to designated power sources as marked on the product. • To avoid potential damage to the electric cord, only remove it by grasping onto the AC adaptor rather than the cord itself from the outlet. • Ensure the cord is well positioned as to avoid potential damage. • Before attempting to clean, please unplug the unit from any power source to avoid potential electric shock. • The charger is designed for indoor use only, and must not be used outdoors. Children Do not allow children to play with your Headset since small parts may become a choking hazard. Emergency Calls

IMPORTANT! Connection cannot be guaranteed at all times under all conditions as the Headset used with the electronic device operates using radio signals, landline and cellular networks. Therefore its not recommended depending primarily on any electronic device for essential communication (e.g. 911 calls). Keep in mind that when making or receiving calls, the Headset and the electronic device connected to it must be turned on and within signal strength. Emergency calls can sometimes be disturbed on certain cellular phone networks or when certain network services and/or phone features are in use. Check with your local cellular service provider for details. Battery Information New Batteries The battery is not fully charged when it is new. For first time use, insert the adaptor into the Headset to charge it full until the indicator light turns green. Battery use and care Note: Only Qualified Service Centers are authorized to remove or replace the battery. If treated with care, a rechargeable battery has a long service life. A new battery, or one that has not been used for a long period of time, could have reduced capacity the first few times it is used. • Use only Motorola original accessories. Use of non-original Motorola accessories could be risky and the warranty is void should the product failure is caused by using non-Motorola original accessories. • Do not expose your battery in an environment temperature above +55°C (+131°F). If the battery is operated in cold temperatures, the battery capacity is reduced. Use your battery in room temperature for maximum battery capacity. • The battery can only be charged when the temperature is between +10°C (+50°F) and +45°C (+113°F).

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. 15.21 Federal Communications Commission (FCC) Statement The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures: ---Reorient or relocate the receiving antenna. ---Increase the separation between the equipment and receiver. ---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ---Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. Installation and use of this Bluetooth Headset device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines.