Cambium Networks XI-N450 802.11abgn 3x3 Module User Manual xirrus PDF
Xirrus, Inc. 802.11abgn 3x3 Module xirrus PDF
Contents
Manual (Part 1 of 2)
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1507766 |
| Application ID | buglAaioT2+KEb0U97H2XA== |
| Document Description | Manual (Part 1 of 2) |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 352.4kB (4404974 bits) |
| Date Submitted | 2011-07-24 00:00:00 |
| Date Available | 2011-09-26 00:00:00 |
| Creation Date | 2010-12-30 12:23:51 |
| Producing Software | Acrobat Distiller 9.4.0 (Windows) |
| Document Lastmod | 2010-12-30 12:24:07 |
| Document Title | xirrus_PDF.book |
| Document Creator | Adobe Illustrator CS3 |
| Document Author: | Shelly |
DRAFT December 17, 2010 Release 5.0 Wi-Fi Array ™ XR4420, XR4430, XR4820, XR4830 XN16, XN12, XN8, XN4 XS16, XS8, XS4 All rights reserved. This document may not be reproduced or disclosed in whole or in part by any means without the written consent of Xirrus, Inc. Part Number: 800-0xxx-001 (Revision A) Trademarks is a registered trademark of Xirrus, Inc. All other trademarks and brand names are marks of their respective holders. Please see Legal Notices, Warnings, Compliance Statements, and Warranty and License Agreements in “Appendix F: Notices” on page 467. Xirrus, Inc. 2101 Corporate Center Drive Thousand Oaks, CA 91320 USA Tel: Fax: 1.805.262.1600 1.800.947.7871 Toll Free in the US 1.866.462.3980 www.xirrus.com Wi-Fi Array Table of Contents List of Figures...................................................................................... xi Introduction ......................................................................................... 1 The Xirrus Family of Products ............................................................................... 2 Nomenclature .................................................................................................... 4 About this User’s Guide .......................................................................................... 5 Organization ...................................................................................................... 5 Notes and Cautions .......................................................................................... 7 Screen Images .................................................................................................... 7 Your User’s Guide as a PDF Document ........................................................ 7 Hyperlinks ......................................................................................................... 7 Window or Page? .............................................................................................. 7 Why Choose the Xirrus Wi-Fi Array? ................................................................... 8 Wi-Fi Array Product Overview ............................................................................. 9 Enterprise Class Security ................................................................................. 9 Wi-Fi Array Product Family ......................................................................... 10 XR4000 Family of Arrays ........................................................................ 10 XN Family of Arrays ............................................................................... 11 XS Family of Arrays ................................................................................ 12 Deployment Flexibility .................................................................................. 13 Power over Gigabit Ethernet (PoGE) .................................................... 14 Enterprise Class Management ...................................................................... 14 Key Features and Benefits ..................................................................................... 17 High Capacity and High Performance ........................................................ 17 Extended Coverage ......................................................................................... 18 Flexible Coverage Schemes .................................................................... 19 Non-Overlapping Channels .......................................................................... 19 SDMA Optimization ...................................................................................... 20 Fast Roaming ................................................................................................... 20 Easy Deployment ............................................................................................ 20 Secure Wireless Access .................................................................................. 20 Applications Enablement .............................................................................. 20 Advanced Feature Sets .......................................................................................... 20 Wi-Fi Array Xirrus Advanced RF Performance Manager (RPM) .................................. 21 Xirrus Advanced RF Security Manager (RSM) .......................................... 22 Xirrus Advanced RF Analysis Manager (RAM) ......................................... 22 Product Specifications — XR4400 and XR4800 Series ........................................ 23 Product Specifications — XN16, XN12, and XN8 ............................................... 31 Product Specifications — XN4 .............................................................................. 38 Product Specifications — XS16 and XS8 .............................................................. 45 Product Specifications — XS4 ............................................................................... 51 Installing the Wi-Fi Array ................................................................. 57 Installation Prerequisites ...................................................................................... 57 Optional Network Components ................................................................... 59 Client Requirements ....................................................................................... 59 Planning Your Installation .................................................................................... 60 General Deployment Considerations .......................................................... 60 Coverage and Capacity Planning ................................................................. 62 Placement .................................................................................................. 62 RF Patterns ................................................................................................ 63 Capacity and Cell Sizes ........................................................................... 65 Fine Tuning Cell Sizes ............................................................................. 66 Roaming Considerations ........................................................................ 67 Allocating Channels ................................................................................ 67 Deployment Examples ............................................................................ 70 IEEE 802.11n Deployment Considerations ................................................. 72 MIMO (Multiple-In Multiple-Out) ........................................................ 73 Multiple Data Streams — Spatial Multiplexing ................................... 75 Channel Bonding ..................................................................................... 76 Improved MAC Throughput ................................................................. 77 Short Guard Interval ............................................................................... 77 Obtaining Higher Data Rates ................................................................. 78 802.11n Capacity ...................................................................................... 79 Failover Planning ............................................................................................ 80 Port Failover Protection .......................................................................... 80 Switch Failover Protection ..................................................................... 81 Power Planning ............................................................................................... 82 AC Power .................................................................................................. 82 Power over Gigabit Ethernet ................................................................. 82 ii Wi-Fi Array Security Planning ............................................................................................ 83 Wireless Encryption ................................................................................ 83 Authentication ......................................................................................... 83 Meeting PCI DSS Standards ................................................................... 84 Meeting FIPS Standards ......................................................................... 84 Port Requirements .......................................................................................... 86 Network Management Planning .................................................................. 89 WDS Planning ................................................................................................. 90 Common Deployment Options .................................................................... 93 Installation Workflow ........................................................................................... 94 Installing Your Wi-Fi Array .................................................................................. 96 Choosing a Location ....................................................................................... 96 Wiring Considerations ............................................................................ 97 Mounting the Array ....................................................................................... 99 Dismounting the Array .................................................................................. 99 Powering Up the Wi-Fi Array ............................................................................ 100 Array LED Operating Sequences ............................................................... 101 LED Boot Sequence ............................................................................... 101 LED Operation when Array is Running ............................................ 102 Establishing Communication with the Array .................................................. 103 Using the Serial Port ..................................................................................... 103 Using the Ethernet Ports .............................................................................. 103 Logging In ...................................................................................................... 104 Entering the License ............................................................................................ 104 Performing the Express Setup Procedure ......................................................... 106 Procedure for Performing an Express Setup ............................................ 107 The Web Management Interface ................................................ 113 An Overview ........................................................................................................ 114 Structure of the WMI ........................................................................................... 115 User Interface ....................................................................................................... 117 Utility Buttons ........................................................................................ 119 Logging In ............................................................................................................. 121 Applying Configuration Changes ..................................................................... 121 Character Restrictions .................................................................................. 121 iii Wi-Fi Array Viewing Status on the Wi-Fi Array............................................... 123 Array Status Windows ........................................................................................ 123 Array Summary ............................................................................................ 124 Content of the Array Summary Window .......................................... 124 Array Information ........................................................................................ 127 Array Configuration ..................................................................................... 128 Admin History .............................................................................................. 129 Network Status Windows ................................................................................... 129 Network ......................................................................................................... 130 Network Map ................................................................................................ 131 Content of the Network Map Window .............................................. 131 Spanning Tree Status .................................................................................... 133 Routing Table ................................................................................................ 135 ARP Table ...................................................................................................... 135 DHCP Leases ................................................................................................. 136 Connection Tracking/NAT ......................................................................... 136 CDP Neighbors ............................................................................................. 137 Network Assurance ...................................................................................... 138 RF Monitor Windows .......................................................................................... 139 IAPs ................................................................................................................. 140 Spectrum Analyzer ...................................................................................... 141 Intrusion Detection ...................................................................................... 145 Station Status Windows ...................................................................................... 147 Stations ........................................................................................................... 148 Location Map ................................................................................................. 149 RSSI ................................................................................................................. 153 Signal-to-Noise Ratio (SNR) ........................................................................ 155 Noise Floor ..................................................................................................... 157 Max by IAP .................................................................................................... 159 Statistics Windows ............................................................................................... 160 IAP Statistics Summary ................................................................................ 160 Per-IAP Statistics ........................................................................................... 161 Network Statistics ......................................................................................... 163 VLAN Statistics ............................................................................................. 164 WDS Statistics ................................................................................................ 165 Filter Statistics ............................................................................................... 166 Station Statistics ............................................................................................ 166 iv Wi-Fi Array Per-Station Statistics ..................................................................................... 167 System Log Window ........................................................................................... 168 Configuring the Wi-Fi Array .......................................................... 171 Express Setup ........................................................................................................ 173 Network ................................................................................................................. 179 Network Interfaces ...................................................................................... 180 Network Interface Ports ........................................................................ 181 DNS Settings .................................................................................................. 187 CDP Settings .................................................................................................. 189 Services .................................................................................................................. 191 Time Settings (NTP) ..................................................................................... 192 NetFlow .......................................................................................................... 194 Wi-Fi Tag ....................................................................................................... 195 System Log ..................................................................................................... 196 SNMP .............................................................................................................. 199 DHCP Server ................................................................................................. 202 VLANs ................................................................................................................... 205 Understanding Virtual Tunnels .......................................................... 205 VLAN Management ..................................................................................... 207 Security .................................................................................................................. 209 Understanding Security ........................................................................ 210 Certificates and Connecting Securely to the WMI ............................ 213 Using the Array’s Default Certificate ................................................. 214 Using an External Certificate Authority ............................................. 215 Admin Management .................................................................................... 215 Admin Privileges .......................................................................................... 216 Admin RADIUS ............................................................................................ 218 About Creating Admin Accounts on the RADIUS Server ............. 219 Management Control ................................................................................... 222 Access Control List ....................................................................................... 229 Global Settings .............................................................................................. 231 External Radius ............................................................................................. 234 About Creating User Accounts on the RADIUS Server .................. 235 Internal Radius .............................................................................................. 238 Rogue Control List ........................................................................................ 241 SSIDs ...................................................................................................................... 243 Wi-Fi Array Understanding SSIDs ............................................................................ 244 Understanding QoS Priority on the Wi-Fi Array .............................. 245 SSID Management ........................................................................................ 248 SSID List (top of page) .......................................................................... 249 SSID Limits ............................................................................................. 253 Web Page Redirect Configuration Settings ....................................... 254 WPA Configuration Settings .............................................................. 258 RADIUS Configuration Settings ......................................................... 258 Active IAPs .................................................................................................... 259 Per-SSID Access Control List ...................................................................... 260 Groups ................................................................................................................... 262 Understanding Groups ......................................................................... 262 Using Groups ......................................................................................... 263 Group Management ..................................................................................... 264 Group Limits .......................................................................................... 266 IAPs ........................................................................................................................ 268 Understanding Fast Roaming .............................................................. 270 IAP Settings ................................................................................................... 271 Global Settings (IAP) ................................................................................... 277 Beacon Configuration ........................................................................... 279 Station Management ............................................................................. 279 Advanced Traffic Optimization .......................................................... 280 Global Settings .11a ...................................................................................... 284 Global Settings .11bg .................................................................................... 287 Global Settings .11n ...................................................................................... 291 Advanced RF Settings .................................................................................. 294 About Standby Mode ............................................................................ 294 About Blocking Rogue APs .................................................................. 295 RF Intrusion Detection .......................................................................... 296 RF Resilience .......................................................................................... 297 RF Power & Sensitivity ......................................................................... 298 RF Spectrum Management ................................................................... 299 LED Settings .................................................................................................. 303 WDS ....................................................................................................................... 305 About Configuring WDS Links ........................................................... 305 WDS Client Links .......................................................................................... 307 Filters ..................................................................................................................... 310 vi Wi-Fi Array Filter Lists ...................................................................................................... 311 Filter Management ....................................................................................... 313 Clusters .................................................................................................................. 316 Cluster Definition ........................................................................................ 317 Cluster Management ................................................................................... 318 Cluster Operation ........................................................................................ 319 Using Tools on the Wi-Fi Array..................................................... 323 System Tools ......................................................................................................... 324 About Licensing and Upgrades ........................................................... 325 System ..................................................................................................... 326 Automatic Updates from Remote Image or Configuration File .... 327 Configuration ......................................................................................... 328 Diagnostics ............................................................................................. 330 Web Page Redirect ................................................................................. 332 Network Tools ........................................................................................ 333 Progress and Status Frames ................................................................. 335 CLI ......................................................................................................................... 336 Options .................................................................................................................. 337 Logout .................................................................................................................... 340 The Command Line Interface ...................................................... 341 Establishing a Secure Shell (SSH) Connection ................................................. 341 Getting Started with the CLI .............................................................................. 343 Inputting Commands ................................................................................... 343 Getting Help .................................................................................................. 343 Top Level Commands ......................................................................................... 346 Root Command Prompt ............................................................................... 346 configure Commands ................................................................................... 347 show Commands .......................................................................................... 350 statistics Commands ..................................................................................... 353 Configuration Commands .................................................................................. 355 acl .................................................................................................................... 355 admin .............................................................................................................. 356 cdp ................................................................................................................... 357 clear ................................................................................................................. 358 cluster ............................................................................................................. 359 vii Wi-Fi Array contact-info .................................................................................................... 360 date-time ........................................................................................................ 361 dhcp-server .................................................................................................... 362 dns ................................................................................................................... 363 file .................................................................................................................... 364 filter ................................................................................................................. 367 group .............................................................................................................. 369 hostname ........................................................................................................ 369 interface .......................................................................................................... 370 load ................................................................................................................. 371 location ........................................................................................................... 371 management .................................................................................................. 372 more ................................................................................................................ 373 netflow ............................................................................................................ 374 no ..................................................................................................................... 375 quit .................................................................................................................. 377 radius-server .................................................................................................. 377 reboot .............................................................................................................. 378 reset ................................................................................................................. 378 restore ............................................................................................................. 379 run-tests .......................................................................................................... 380 security ........................................................................................................... 382 snmp ............................................................................................................... 383 ssid .................................................................................................................. 384 syslog .............................................................................................................. 385 uptime ............................................................................................................. 386 vlan .................................................................................................................. 387 wifi-tag ........................................................................................................... 388 Sample Configuration Tasks .............................................................................. 389 Configuring a Simple Open Global SSID .................................................. 390 Configuring a Global SSID using WPA-PEAP ......................................... 391 Configuring an SSID-Specific SSID using WPA-PEAP ........................... 392 Enabling Global IAPs ................................................................................... 393 Disabling Global IAPs .................................................................................. 394 Enabling a Specific IAP ................................................................................ 395 Disabling a Specific IAP ............................................................................... 396 Setting Cell Size Auto-Configuration for All IAPs .................................. 397 viii Wi-Fi Array Setting the Cell Size for All IAPs ................................................................ 398 Setting the Cell Size for a Specific IAP ....................................................... 399 Configuring VLANs on an Open SSID ...................................................... 400 Configuring Radio Assurance Mode (Loopback Tests) .......................... 401 Appendices..................................................................................... 403 Appendix A: Servicing the Wi-Fi Array ............................................................. 405 Removing the Access Panel ................................................................................ 407 Reinstalling the Access Panel ............................................................................. 410 Replacing the FLASH Memory Module ........................................................... 412 Replacing the Main System Memory ................................................................ 414 Replacing the Integrated Access Point Radio Module ................................... 416 Replacing the Power Supply Module ............................................................... 419 Appendix B: Quick Reference Guide ............................................................... 421 Factory Default Settings ...................................................................................... 421 Host Name ..................................................................................................... 421 Network Interfaces ....................................................................................... 421 Serial ........................................................................................................ 421 Gigabit 1 and Gigabit 2 ......................................................................... 422 Fast Ethernet ........................................................................................... 422 Integrated Access Points (IAPs) .................................................................. 423 Server Settings ............................................................................................... 424 NTP .......................................................................................................... 424 Syslog ...................................................................................................... 424 SNMP ...................................................................................................... 424 DHCP .............................................................................................................. 425 Default SSID .................................................................................................. 425 Security .......................................................................................................... 426 Global Settings - Encryption ............................................................... 426 External RADIUS (Global) .................................................................. 426 Internal RADIUS .................................................................................... 427 Administrator Account and Password ...................................................... 428 Management .................................................................................................. 428 Keyboard Shortcuts ............................................................................................. 428 Appendix C: Technical Support ........................................................................ 431 General Hints and Tips ....................................................................................... 431 ix Wi-Fi Array Frequently Asked Questions .............................................................................. 432 Multiple SSIDs ............................................................................................... 432 Security ........................................................................................................... 434 VLAN Support .............................................................................................. 438 Array Monitor and Radio Assurance Capabilities .......................................... 440 Enabling Monitoring on the Array ..................................................... 440 How Monitoring Works ............................................................................... 440 Radio Assurance ........................................................................................... 441 Radio Assurance Options ..................................................................... 442 RADIUS Vendor Specific Attributes (VSAs) for Xirrus ................................. 443 Upgrading the Array via CLI ............................................................................. 446 Sample Output for the Upgrade Procedure: ............................................. 447 Power over Gigabit Ethernet Compatibility Matrix ....................................... 451 Contact Information ............................................................................................ 453 Appendix D: Implementing PCI DSS ............................................................... 455 Payment Card Industry Data Security Standard Overview .......................... 455 PCI DSS and Wireless .......................................................................................... 456 The Xirrus Array PCI Compliance Configuration .......................................... 457 The pci-audit Command ..................................................................................... 458 Additional Resources .......................................................................................... 459 Appendix E: Implementing FIPS Security ....................................................... 461 Appendix F: Notices ........................................................................................... 467 Notices ................................................................................................................... 467 EU Directive 1999/5/EC Compliance Information ........................................ 470 Compliance Information (Non-EU) ................................................................... 477 Safety Warnings ................................................................................................... 478 Translated Safety Warnings ............................................................................... 479 Software License and Product Warranty Agreement ..................................... 480 Hardware Warranty Agreement ....................................................................... 486 Glossary of Terms.......................................................................... 489 Index................................................................................................ 501 Wi-Fi Array List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Figure 31. Figure 32. Figure 33. Figure 34. Xirrus Arrays............................................................................................... 2 The Xirrus Management System .............................................................. 3 Wi-Fi Array (XN16) .................................................................................... 9 Wireless Coverage Patterns .................................................................... 13 XP8 - Power over Ethernet Usage .......................................................... 14 WMI: Array Status.................................................................................... 15 Layout of IAPs (XN16)............................................................................. 17 Naming of IAPs (XS16) ............................................................................ 18 Coverage Schemes (XS16 shown)........................................................... 19 Wall Thickness Considerations .............................................................. 61 Unit Placement.......................................................................................... 62 Full (Normal) Coverage........................................................................... 63 Adjusting RF Patterns .............................................................................. 64 Custom Coverage ..................................................................................... 64 Connection Rate vs. Distance.................................................................. 65 Transmit Power......................................................................................... 66 Overlapping Cells..................................................................................... 67 Allocating Channels Manually ............................................................... 69 Deployment Scenario (54 Mbps) — Per Sector...................................... 70 Deployment Scenario (36 Mbps) — Per Sector...................................... 70 Deployment Scenario (18 Mbps) — Per Sector...................................... 71 Classic 802.11 Signal Transmission ........................................................ 73 MIMO Signal Processing ......................................................................... 74 Spatial Multiplexing................................................................................. 75 Channel Bonding ...................................................................................... 76 MAC Throughput Improvements.......................................................... 77 Computing 802.11n Data Rates .............................................................. 78 802.11n Increases Capacity...................................................................... 79 Port Failover Protection ........................................................................... 80 Switch Failover Protection ...................................................................... 81 Port Requirements for XMS .................................................................... 86 WDS Link................................................................................................... 90 A Multiple Hop WDS Connection ......................................................... 91 WDS Failover Protection ......................................................................... 91 List of Figures xi Wi-Fi Array Figure 35. Figure 36. Figure 37. Figure 38. Figure 39. Figure 40. Figure 41. Figure 42. Figure 43. Figure 44. Figure 45. Figure 46. Figure 47. Figure 48. Figure 49. Figure 50. Figure 51. Figure 52. Figure 53. Figure 54. Figure 55. Figure 56. Figure 57. Figure 58. Figure 59. Figure 60. Figure 61. Figure 62. Figure 63. Figure 64. Figure 65. Figure 66. Figure 67. Figure 68. Figure 69. Figure 70. Figure 71. xii Installation Workflow .............................................................................. 94 Array Placement ....................................................................................... 96 LED Locations (XN16) ........................................................................... 100 Network Interface Ports......................................................................... 103 Express Setup .......................................................................................... 106 LEDs are Switched On ........................................................................... 111 Web Management Interface .................................................................. 114 WMI: Frames ........................................................................................... 117 WMI: Utility Buttons.............................................................................. 119 Feedback Form........................................................................................ 120 Logging In to the Wi-Fi Array .............................................................. 121 Array Summary ...................................................................................... 124 Disabled IAP (Partial View) .................................................................. 125 IAP Cells .................................................................................................. 126 Array Information .................................................................................. 127 Show Configuration ............................................................................... 128 Admin Login History............................................................................. 129 Network Settings .................................................................................... 130 Network Map .......................................................................................... 131 Spanning Tree Status.............................................................................. 134 Routing Table .......................................................................................... 135 ARP Table ................................................................................................ 135 DHCP Leases........................................................................................... 136 Connection Tracking .............................................................................. 136 CDP Neighbors ....................................................................................... 137 Network Assurance................................................................................ 138 RF Monitor — IAPs ................................................................................. 140 RF Spectrum Analyzer........................................................................... 142 Intrusion Detection/Rogue AP List..................................................... 145 Stations ..................................................................................................... 148 Location Map........................................................................................... 149 Controls for Location Map .................................................................... 150 Minimizing stations................................................................................ 151 Station RSSI Values ................................................................................ 153 Station RSSI Values — Colorized Graphical View ............................. 154 Station Signal-to-Noise Ratio Values................................................... 155 Station SNR Values — Colorized Graphical View.............................. 156 List of Figures Wi-Fi Array Figure 72. Figure 73. Figure 74. Figure 75. Figure 76. Figure 77. Figure 78. Figure 79. Figure 80. Figure 81. Figure 82. Figure 83. Figure 84. Figure 85. Figure 86. Figure 87. Figure 88. Figure 89. Figure 90. Figure 91. Figure 92. Figure 93. Figure 94. Figure 95. Figure 96. Figure 97. Figure 98. Figure 99. Figure 100. Figure 101. Figure 102. Figure 103. Figure 104. Figure 105. Figure 106. Figure 107. Figure 108. Station Noise Floor Values .................................................................... 157 Station Noise Floor Values — Colorized Graphical View ................. 158 Max by IAP .............................................................................................. 159 IAP Statistics Summary Page................................................................ 161 Individual IAP Statistics Page (for IAP abg(n)1) ............................... 162 Network Statistics................................................................................... 163 VLAN Statistics....................................................................................... 164 WDS Statistics ......................................................................................... 165 Filter Statistics ......................................................................................... 166 Station Statistics ...................................................................................... 166 Individual Station Statistics Page......................................................... 167 System Log ............................................................................................. 168 WMI: Express Setup ............................................................................... 173 LEDs are Switched On ........................................................................... 178 Network Interfaces ................................................................................. 179 Network Settings .................................................................................... 180 Network Interface Ports......................................................................... 181 Port Modes (a-b) ..................................................................................... 183 Port Modes (c-d) ..................................................................................... 184 Port Modes (e-f) ...................................................................................... 185 DNS Settings............................................................................................ 187 CDP Settings............................................................................................ 189 Services..................................................................................................... 191 Time Settings (Manual Time)................................................................ 192 Time Settings (NTP Time Enabled)...................................................... 193 NetFlow.................................................................................................... 194 Wi-Fi Tag.................................................................................................. 195 System Log .............................................................................................. 196 SNMP ....................................................................................................... 199 DHCP Management ............................................................................... 202 VLANs...................................................................................................... 205 VLAN Management ............................................................................... 207 Security..................................................................................................... 209 Import Xirrus Certificate Authority..................................................... 214 Admin Management .............................................................................. 215 Admin Privileges .................................................................................... 217 Admin RADIUS ...................................................................................... 220 List of Figures xiii Wi-Fi Array Figure 109. Figure 110. Figure 111. Figure 112. Figure 113. Figure 114. Figure 115. Figure 116. Figure 117. Figure 118. Figure 119. Figure 120. Figure 121. Figure 122. Figure 123. Figure 124. Figure 125. Figure 126. Figure 127. Figure 128. Figure 129. Figure 130. Figure 131. Figure 132. Figure 133. Figure 134. Figure 135. Figure 136. Figure 137. Figure 138. Figure 139. Figure 140. Figure 141. Figure 142. Figure 143. Figure 144. Figure 145. xiv Management Control ............................................................................. 222 Pre-login Banner ..................................................................................... 223 Access Control List ................................................................................. 229 Global Settings (Security) ...................................................................... 231 External RADIUS Server ....................................................................... 234 Internal RADIUS Server ........................................................................ 238 Rogue Control List ................................................................................. 241 SSIDs......................................................................................................... 243 Four Traffic Classes ................................................................................ 245 SSID Management .................................................................................. 248 SSID Management .................................................................................. 252 WPR Internal Splash Page Fields (SSID Management)..................... 254 Customizing an Internal Login or Splash Page.................................. 257 Setting Active IAPs per SSID ................................................................ 259 Per-SSID Access Control List ................................................................ 260 Groups...................................................................................................... 262 Group Management ............................................................................... 264 IAPs........................................................................................................... 268 Source of Channel Setting ..................................................................... 269 IAP Settings ............................................................................................. 271 Global Settings (IAPs) ............................................................................ 277 Global Settings .11a ................................................................................ 284 Global Settings .11bg.............................................................................. 287 Global Settings .11n ................................................................................ 291 Advanced RF Settings............................................................................ 294 LED Settings ............................................................................................ 303 WDS .......................................................................................................... 305 .Configuring a WDS Link ...................................................................... 306 WDS Client Links ................................................................................... 307 Filters ........................................................................................................ 310 Filter Lists ................................................................................................ 311 Filter Management ................................................................................. 313 Clusters .................................................................................................... 316 Cluster Definition ................................................................................... 317 Cluster Management.............................................................................. 318 Cluster Mode Operation........................................................................ 319 Cluster Mode Activation ....................................................................... 319 List of Figures Wi-Fi Array Figure 146. Figure 147. Figure 148. Figure 149. Figure 150. Figure 151. Figure 152. Figure 153. Figure 154. Figure 155. Figure 156. Figure 157. Figure 158. Figure 159. Figure 160. Figure 161. Figure 162. Figure 163. Figure 164. Figure 165. Figure 166. Figure 167. Figure 168. Figure 169. Figure 170. Figure 171. Figure 172. Figure 173. Figure 174. Figure 175. Figure 176. Figure 177. Figure 178. Figure 179. Figure 180. Figure 181. Figure 182. Viewing Statistics in Cluster Mode...................................................... 320 Status Display in Cluster Mode............................................................ 321 System Tools............................................................................................ 324 Saving the Diagnostic Log..................................................................... 331 Managing WPR Splash/Login page files............................................ 332 System Command (Ping)....................................................................... 333 Radius Ping Command.......................................................................... 333 Radius Ping Output................................................................................ 334 CLI Window ............................................................................................ 336 WMI Display Options ............................................................................ 337 iPhone Style Option................................................................................ 338 Login Window ........................................................................................ 340 Logging In................................................................................................ 342 Help Window.......................................................................................... 344 Full Help .................................................................................................. 345 Partial Help.............................................................................................. 345 Configuring a Simple Open Global SSID............................................ 390 Configuring a Global SSID using WPA-PEAP................................... 391 Configuring an SSID-Specific SSID using WPA-PEAP..................... 392 Enabling Global IAPs............................................................................. 393 Disabling Global IAPs............................................................................ 394 Enabling a Specific IAP.......................................................................... 395 Disabling a Specific IAP......................................................................... 396 Setting the Cell Size for All IAPs.......................................................... 397 Setting the Cell Size for All IAPs.......................................................... 398 Setting the Cell Size for a Specific IAP ................................................ 399 Configuring VLANs on an Open SSID................................................ 400 Configuring Radio Assurance Mode (Loopback Testing)................ 402 Disconnecting Power from the Array.................................................. 405 Removing the Access Panel Screws ..................................................... 407 Removing the Access Panel .................................................................. 408 Disconnecting the Power Supply and Fan.......................................... 408 Reconnecting the Fan and Power Supply ........................................... 410 Reinstalling the Access Panel................................................................ 410 Removing the FLASH Memory Module ............................................. 412 Removing the DIMM Memory Module .............................................. 414 Removing the Chassis Cover Screws................................................... 416 List of Figures xv Wi-Fi Array Figure 183. Figure 184. Figure 185. Figure 186. Figure 187. Figure 188. Figure 189. Figure 190. xvi Removing the Chassis Cover ................................................................ 416 Lifting the Integrated Access Point Module ....................................... 417 Disconnect the Integrated Access Point Module ............................... 417 Installing a New Access Panel (with Power Supply) ........................ 419 Sample output of pci-audit command................................................. 459 Applying Three Seals to XS16/XS8...................................................... 462 Applying Two Tamper-evident seals to the XS4 or XN4 ................. 463 Security - Management Control Window .......................................... 464 List of Figures Wi-Fi Array Introduction These topics introduce the Xirrus Wi-Fi Array, including an overview of its key features and benefits, and a detailed listing of the product’s physical, environmental, technology and regulatory specifications. “The Xirrus Family of Products” on page 2. “About this User’s Guide” on page 5. “Why Choose the Xirrus Wi-Fi Array?” on page 8. “Wi-Fi Array Product Overview” on page 9. “Key Features and Benefits” on page 17. “Advanced Feature Sets” on page 20. “Product Specifications — XR4400 and XR4800 Series” on page 23. “Product Specifications — XN16, XN12, and XN8” on page 31. “Product Specifications — XN4” on page 38. “Product Specifications — XS16 and XS8” on page 45. “Product Specifications — XS4” on page 51. Introduction Wi-Fi Array The Xirrus Family of Products Figure 1. Xirrus Arrays The Xirrus family of products includes the following: The XS Series of Xirrus Wi-Fi Arrays (XS16 / XS8 / XS4) XS Arrays integrate multiple Integrated Access Points — radios with highgain directional antennas for increased range and coverage. The Array also incorporates an onboard multi-gigabit switch, Wi-Fi controller, and firewall into a single device, along with a dedicated Wi-Fi threat sensor and an embedded spectrum analyzer. The Wi-Fi Array provides more than enough bandwidth, security, and control to replace switched Ethernet to the desktop as the primary network connection. The XS16 has 16 IAPs, the XS8 has 8 IAPs, and the XS4 has 4 IAPs. The XN Series of Xirrus Wi-Fi Arrays (XN16 / XN12 / XN8 / XN4) The XN series of Wi-Fi Arrays add the speed and reach of IEEE 802.11n technology to the XS series of Arrays. The XN Series of Arrays feature the capacity and performance needed to replace switched Ethernet to the desktop. The XN16 has 16 IAPs, the XN12 has 12 IAPs, the XN8 has 8 IAPs, and the XN4 has 4 IAPs. Introduction Wi-Fi Array The XR 4000 Series of Xirrus Wi-Fi Arrays The newest Xirrus Wi-Fi Arrays have been completely redesigned to optimize the speed and reach of IEEE 802.11n technology. The XR4000 Series of Arrays have increased the capacity and performance needed to replace switched Ethernet to the desktop. 8-radio and 4-radio models are avialable Xirrus Management System (XMS) XMS is used for managing large Array deployments from a centralized Web-based interface. The XMS server is available pre-installed on the Xirrus XM-33xx-CC Management Appliance series, or as a software package (XA-3300-CC) to be installed on your own server hardware. Figure 2 illustrates the elements of the Xirrus Management System. Users start the XMS client simply by entering the URL of the XMS server on a web browser. The XMS server manages a number of Wi-Fi Arrays via SNMP. Figure 2. The Xirrus Management System Introduction Wi-Fi Array If you need detailed information about this product, refer to the XMS User’s Guide, part number 800-0007-001. Xirrus Power over Gigabit Ethernet (PoGE) The PoGE modules eliminate the need for running separate power cabling. Additionally, an eight port module provides distributed power to multiple Arrays, facilitating backup power when connected via a UPS. Nomenclature Throughout this User’s Guide, the Xirrus Wi-Fi Array is also referred to as simply the Array. In some instances, the terms product and unit are also used. When discussing specific products from the Xirrus family, the product name is used (for example, XN16 or XS8). The Wi-Fi Array’s operating system is referred to as the ArrayOS. The Web Management Interface for browser-based management of the Array is referred to as WMI. The XS series of Arrays have two types of radios — the 5 GHz 802.11a radios are named a1 to a12 (for 16-port models). The 802.11a/b/g radios are named abg1 to abg4, and they support both 2.4GHz and 5 GHz. The XN and XR4000 series of Arrays also have two types of radios — the 5 GHz 802.11a/n radios are named an1 through an12 (for 16-port models). The 802.11a/b/g/n radios are named abgn1 to abgn4, and they also support both 2.4GHz and 5 GHz. When referring to a port that may be on either an XR4000, XN or XS model, the nomenclature abg(n) and a(n) will be used, e.g., abg(n)2 or a(n)6. The Xirrus Management System is referred to as XMS. The Power over Gigabit Ethernet system may be referred to as PoGE. Introduction Wi-Fi Array About this User’s Guide This User’s Guide provides detailed information and procedures that will enable wireless network administrators to install, configure and manage the Wi-Fi Array so that end users can take full advantage of the product’s features and functionality without technical assistance. Organization Topics and procedures are organized by function under the following chapter headings: Introduction Provides a brief introduction to wireless technology, an overview of the product, including its key features and benefits, and presents the product specifications. Installing the Wi-Fi Array Defines prerequisites for deploying and installing the Array and provides instructions to help you plan and complete a successful installation. The Web Management Interface Offers an overview of the product’s embedded Web Management Interface, including its content and structure. It emphasizes what you need to do to ensure that any configuration changes you make are applied, and provides a list of restricted characters. It also includes instructions for logging in to the Array with your Web browser. Viewing Status on the Wi-Fi Array Describes the status and statistics displays available on the Array using its embedded Web Management Interface. Configuring the Wi-Fi Array Contains procedures for configuring the Array using its embedded Web Management Interface. Using Tools on the Wi-Fi Array Contains procedures for using utility tools provided in the Web Management Interface. It includes procedures for upgrading the system Introduction Wi-Fi Array firmware, uploading and downloading configurations and other files, using diagnostic tools, and resetting the Array to its factory defaults. The Command Line Interface Includes the commands and the command structure used by the Wi-Fi Array’s Command Line Interface (CLI), and provides a procedure for establishing a Telnet connection to the Array. This chapter also includes some sample key configuration tasks using the CLI. Appendix A: Servicing the Wi-Fi Array Contains procedures for servicing the Array, including the removal and reinstallation of major hardware components. Appendix B: Quick Reference Guide Contains the product’s factory default settings. Appendix C: Technical Support Offers guidance to resolve technical issues, including general hints and tips to enhance your product experience, and a procedure for isolating problems within an Array-enabled wireless network. Also includes Frequently Asked Questions (FAQs) and Xirrus contact information. Appendix D: Implementing PCI DSS Discusses meeting security standards with the Array, including FIPS and PCI DSS. Appendix F: Notices Contains the legal notices, licensing, and compliance statements for the Array. Please read this section carefully. Glossary of Terms Provides an explanation of terms directly related to Xirrus product technology, organized alphabetically. Index The index is a valuable information search tool. Use the index to locate specific topics discussed in this User’s Guide. Simply click on any page number in the index to jump to the referenced topic. Introduction Wi-Fi Array Notes and Cautions The following symbols are used throughout this User’s Guide: This symbol is used for general notes that provide useful supplemental information. This symbol is used for cautions. Cautions provide critical information that may adversely affect the performance of the product. Screen Images Some screen images of the Web Management Interface have been modified for clarity. For example, an image may have been cropped to highlight a specific area of the screen, and/or sample data may be included in some fields. Your User’s Guide as a PDF Document This User’s Guide is also made available as a secure PDF (Portable Document Format) file and can be viewed using the Adobe® Acrobat Reader® product. It cannot be edited or modified. If you don’t have Acrobat Reader, you can downloaded it free-of-charge from: http://www.adobe.com. Hyperlinks If you click on body text that appears in the color TEAL (with the exception of headings or notes) the embedded hyperlink within the text will immediately take you to the referenced destination. All internal and external cross-references, including page numbers within the List of Figures and the Index, have associated hyperlinks. After “jumping” to a referenced topic, if you want to return to the previous page (reference source), simply click on Acrobat’s previous page button. Window or Page? Is a window a page, or is a page a window? There seems to be some dispute as to what the correct term should be. For the sake of consistency, this document uses the term Window when referring to how the Wi-Fi Array’s Web Management Interface is displayed on your monitor. Introduction Wi-Fi Array Why Choose the Xirrus Wi-Fi Array? The deployment of wireless LANs is becoming increasingly common as businesses strive for greater flexibility in the workplace and the need for employee mobility rises. The only requirements for an effective wireless deployment are a power source, a couple of screws, and a little imagination. Wireless LAN is also fully compatible with standard Ethernet protocols, so connectivity with existing wired infrastructures is transparent to users — they can still access and use the same applications and network services that they use when plugged into the company’s wired LAN infrastructure (it’s only the plug that no longer exists). Wireless LAN has come a long way in the past few years and now offers the performance, reliability and security that Enterprise customers have come to expect from their networks. The technology is being driven by four major IEEE standards: 802.11a Operates in the 5 GHz range with a maximum speed of 54 Mbps. 802.11b Operates in the 2.4 GHz range with a maximum speed of 11 Mbps. 802.11g Supports a higher transmission speed of 54 Mbps in the 2.4 GHz range and is backwards compatible with 802.11b. 802.11n Uses multiple antennas per radio to boost transmission speed as high as 300 Mbps, increasing throughput, range, and maximum number of users. 802.11n is backwards compatible with 802.11a/b/g. Whether you have just a handful of users or thousands of users, wireless has the scalability and flexibility to serve your needs. Introduction Wi-Fi Array Wi-Fi Array Product Overview Part of the family of Xirrus products, the Wi-Fi Array is a high capacity, multimode device designed for the Enterprise market, with twice the range and up to eight times the capacity of competitive wireless products. Figure 3. Wi-Fi Array (XN16) The Wi-Fi Array (regardless of the product model) is Wi-Fi® compliant and simultaneously supports 802.11a, 802.11b and 802.11g clients. XR and XN model arrays add the enhanced abilities of 802.11n to this combination. Active Enterprise class features such as VLAN support and multiple SSID capability enable robust network compatibility and a high level of scalability and system control. The optional Xirrus Management System (XMS) allows global management of hundreds of Arrays from a central location. Multiple versions of the Array with different numbers of Integrated Access Points (IAPs) support a variety of deployment applications: 16 IAPs (XN16, XS16), 12 IAPs (XN12), 8 IAPs (XR4820, XR4830, XN8, XS8), and 4 IAPs (XR4420, XR4430, XN4, XS4). Enterprise Class Security The latest and most effective wireless encryption security standards, including WPA (Wi-Fi Protected Access) and WPA2 with 802.11i AES (Advanced Encryption Standard) are available on the Wi-Fi Array. In addition, the use of an embedded RADIUS server (or 802.1x with an external RADIUS server) ensures user authentication — multiple Arrays can authenticate to the optional XMS, ensuring only authorized Arrays become part of the wireless network. With the Introduction Wi-Fi Array Xirrus Advanced Feature Sets, rogue AP detection, site monitoring, and RF spectrum analysis are performed in the background by the Array automatically. Wi-Fi Array Product Family The following tables provide an overview of the main features supported by the Wi-Fi Array product family. XR4000 Family of Arrays Feature XR4820 XN4420 Number of 802.11a/b/g/n radios Number of 802.11a/n radios Number of integrated antennas 24 12 Integrated Wi-Fi switch ports Yes Yes Wi-Fi bandwidth 2.4 Gbps 1.2 Gbps Users supported 768 384 Total radios Integrated RF spectrum analyzer, threat sensors Uplink Ports 10 Introduction Wi-Fi Array XN Family of Arrays Feature XN16 XN12 XN8 XN4 Number of 802.11a/b/g/n radios Number of 802.11a/n radios 12 16 12 Number of integrated antennas 48 36 24 12 Integrated Wi-Fi switch ports 16 12 Integrated RF spectrum analyzer, threat sensors Yes Yes Yes Yes Wi-Fi bandwidth 4.8 Gbps 3.6 Gbps 2.4 Gbps 1.2 Gbps Users supported 1536 1152 768 384 Total radios Uplink Ports Introduction 11 Wi-Fi Array XS Family of Arrays Feature XS16 XS8 XS4 Number of 802.11a/b/g radios Number of 802.11a radios 12 16 Integrated Wi-Fi switch ports 16 Integrated RF spectrum analyzer and threat sensors Yes Yes Yes Wi-Fi bandwidth 864 Mb 432 Mb 216 Mb Users supported 1,024 512 256 Total radios Uplink Ports 12 Introduction Wi-Fi Array Deployment Flexibility Xirrus’ unique multi-radio architecture generates 360 degrees of sectored highgain 802.11a/b/g/n or 802.11a/b/g coverage that provides extended range and the highest possible data rates for a large volume of clients. Each sector can be controlled automatically or manually, creating a pattern of wireless coverage perfectly tailored to individual customer needs. For example: outside wall Figure 4. Wireless Coverage Patterns Figure 4 depicts the following two scenarios: Full pattern coverage All radios are activated with coverage spanning 360 degrees. If within range, clients will always receive coverage regardless of their geographic position relative to the Array. Partial pattern coverage If desired, the Wi-Fi Array can be deployed close to an exterior wall. In this case, half of all available radios have been deactivated to prevent redundant signals from “bleeding” beyond the site’s perimeter wall. This configuration may also be used in those cases where you want to restrict wireless coverage to selected areas of the building’s interior. See also, “Flexible Coverage Schemes” on page 19. Introduction 13 Wi-Fi Array Power over Gigabit Ethernet (PoGE) The Xirrus XP1, XP2, and XP8 Power over Gigabit Ethernet modules provide power to your Arrays over the same Cat 5e or Cat 6 cable used for data, eliminating the need to run power cables and provide an AC power outlet in proximity to each unit. Managed modules provide the ability to control power using XMS. Figure 5. XP8 - Power over Ethernet Usage Specific models of the Array are compatible with specific PoGE modules. For details, please see “Power over Gigabit Ethernet Compatibility Matrix” on page 451. Enterprise Class Management The Wi-Fi Array can be configured with its default RF settings, or the RF settings can be customized using the Array’s embedded Web Management Interface 14 Introduction Wi-Fi Array (WMI). The WMI enables easy configuration and control from a graphical console, along with a full compliment of troubleshooting tools and statistics. Figure 6. WMI: Array Status In addition, a fully featured Command Line Interface (CLI) offers IT professionals a familiar management and control environment. SNMP (Simple Network Management Protocol) is also supported to allow management from an SNMP compliant management tool, such as the optional Xirrus Management System. Introduction 15 Wi-Fi Array 16 For deployments of more than five Arrays, we recommend that you use the Xirrus Management System (XMS). The XMS offers a rich set of features for fine control over large deployments. Introduction Wi-Fi Array Key Features and Benefits This section describes some of the key product features and the benefits you can expect when deploying the Wi-Fi Array (the XN16 product is highlighted in this section). High Capacity and High Performance an12 an11 abgn4 an1 abgn1 an10 an2 an3 an9 an8 an4 abgn3 abgn2 an7 an5 an6 Mode(s) abgn2 (RF monitoring) IAP number Figure 7. Layout of IAPs (XN16) The XN16 version of the Wi-Fi Array (Figure 7) easily handles time-sensitive traffic such as voice, and can enable wireless connectivity for 1,024 users. The unit includes two Gigabit uplink ports for connection to the wired network. A total of sixteen IAPs provides a maximum wireless capacity of 4.8 Gbps, which offers ample reserves for the high demands of current and future applications. Of the sixteen IAPs, twelve operate as 802.11a/n radios (5 GHz band), and four operate as 802.11a/b/g/n radios (5 GHz or 2.4 GHz bands), providing backwards compatibility with 802.11b and 802.11g. Introduction 17 Wi-Fi Array In the recommended configuration, IAP (radio) abg(n)2 is configured in RF monitoring and rogue AP detection mode. a12 a11 a1 abg4 abg1 a10 a2 a3 a9 a8 a4 abg3 abg2 a7 abg2 (RF monitoring) a5 a6 Mode(s) IAP number Figure 8. Naming of IAPs (XS16) Extended Coverage One XN16 solution enables you to replace up to sixteen access points (includes one omnidirectional IAP for monitoring the network). Fifteen IAP radios with integrated directional antennas provide increased wireless range and enhanced data rates in all directions. With a Wi-Fi Array deployed, far fewer access points are needed and wired-like resiliency is delivered throughout your wireless network. Your Wi-Fi Array deployment ensures: 18 Continuous connectivity if an IAP (radio) fails. Continuous connectivity if an Array fails. Continuous connectivity if a WDS link or switch fails. Continuous connectivity if a Gigabit uplink or switch fails. Introduction Wi-Fi Array Flexible Coverage Schemes Your Wi-Fi Array offers flexible coverage schemes for each wireless technology. Figure 9. Coverage Schemes (XS16 shown) 802.11a/n, 802.11a Delivers 60° wireless coverage per IAP, with 6 dBi of gain. 802.11b/g/n, 802.11b/g Delivers 180° wireless coverage, with 3 dBi of gain. 802.11a/b/g/n, 802.11a/b/g (monitor only) Delivers 360° wireless coverage, with 2 dBi of gain. Non-Overlapping Channels Complete use of non-overlapping channels limits interference and delivers maximum capacity. On the XN16, up to 16 non-overlapping channels are fully utilized across the 5GHz and 2.4GHz spectrums (up to 12 across the 5GHz spectrum plus up to 3 across the 2.4 GHz spectrum — typically, one additional radio is used as a dedicated RF monitor). Introduction 19 Wi-Fi Array SDMA Optimization SDMA (Spatial Division Multiple Access) technology provides full 360° coverage while allowing independent channel and power output customization. Also supports fast inter-zone handoffs for time-sensitive applications and roaming. Fast Roaming Utilizes the Xirrus Roaming Protocol (XRP) ensuring fast and seamless roaming capabilities between IAPs or Arrays at both Layer 2 and Layer 3. Easy Deployment The Xirrus Management System (XMS) offers real time monitoring and management capabilities for the wireless network — ideal for the Enterprise market. It also allows you to import floor plans to help you plan your deployment. The Xirrus Wi-Fi Array chassis has a plenum rated, lockable and tamper resistant case. Secure Wireless Access Multiple layers of authentication and encryption ensure secure data transmissions. The Wi-Fi Array is 802.11i compliant with line-rate encryption support for 40 and 128 bit WEP, WPA and WPA2 with TKIP and AES encryption. Authentication is provided via 802.1x, including PEAP, EAP-TLS, EAP-TTLS, and LEAP (Lightweight Extensible Authentication Protocol) passthrough. Applications Enablement The Wi-Fi Array’s QoS (Quality of Service) functionality combined with true switch capabilities enable high density video and Voice over Wireless LAN deployments. Compliant with 802.1p and 802.1Q standards. Advanced Feature Sets The Wi-Fi Array offers a family of powerful functionality packages, including the RF Performance Manager (RPM), RF Security Manager (RSM), and RF Analysis Manager (RAM). These packages are separately licensed for operation on your Array. 20 Introduction Wi-Fi Array Xirrus Advanced RF Performance Manager (RPM) The Xirrus RPM optimizes the bandwidth usage and station performance of 802.11n Wi-Fi networks. Leveraging the multiple integrated access point (multiradio) design of the Xirrus Wi-Fi Array, RPM manages the allocation of wireless bandwidth to wireless stations across multiple RF channels. The result maximizes overall network performance with superior flexibility and capacity. Today's wireless infrastructure is faced with ever increasing numbers and variations of Wi-Fi enabled clients, whether in the form of notebooks, netbooks, smart phones, IP phones, printers, projectors, cameras, RFID tags, etc. The advent of higher speed 802.11n Wi-Fi and its increased use of the 5GHz spectrum adds to the number of variables today's wireless networks must accommodate. Backwards compatibility with older clients is crucial, however their operation in a Wi-Fi network can significantly hinder the performance of faster clients. As an example, 802.11b Wi-Fi stations communicate more than 10 times slower than 802.11n stations. With each of the Array’s multiple radios operating on a different channel, RPM selects the ideal radio for each station. High-speed stations are grouped together on radios with other high speed stations, while lower speed stations are combined with other lower speed stations. This ensures optimal performance for high-speed 802.11n stations without compromise. The complete feature set of the RPM package includes: WDS (Wireless Distribution System) for point-to-point communication Wi-Fi Mode per IAP Sharp Cell technology Wireless Data Rate Optimization Wireless Traffic Shaping Wireless Voice Call Admission Control Fast Layer 2 and 3 Roaming Standby Mode Introduction 21 Wi-Fi Array Xirrus Advanced RF Security Manager (RSM) The Xirrus RSM improves security and minimizes the risk in deploying 802.11n wireless networks. Leveraging an integrated 24/7 threat sensor and hardwarebased encryption/decryption in each Array, RSM secures the Wi-Fi network from multiple types of threats. The result delivers uncompromised overall network security with superior flexibility and performance. Today's Wi-Fi networks face a number of potential security threats in the form of rogue access points, ad-hoc clients, unauthorized clients, wireless-based attacks, eavesdropping, etc. As 802.11n is increasingly adopted in enterprise networks, defending against these threats becomes more critical. With the Array’s dedicated threat sensor radio scanning all channels in the 2.4GHz and 5GHz spectrums, RSM searches for security threats and automatically mitigates them. High performance encryption/decryption in the enterprise Wi-Fi network is a must. The Wi-Fi network needs to support each client using the highest level of encryption (WPA2 Enterprise/128 bit AES) and without degrading the overall performance of the network. Xirrus incorporates hardware-based encryption/ decryption into each Array, delivering line-rate encryption at the edge of the network instead of at a choke point within a centralized controller. The complete feature set of the RSM package includes: Wireless IDS/IPS (Intrusion Detection/Prevention System) Wireless stateful firewall User group policies Authenticated guest access gateway NAC integration PCI audit compliance enforcement Xirrus Advanced RF Analysis Manager (RAM) The RF Advanced Analysis Manager (RAM) tests and troubleshoots 802.11n wireless networks. The deployment of 802.11n presents a set of unique challenges based on technology differences with legacy 802.11a/b/g networks, both on the wireless infrastructure and client side. Xirrus' RAM equips each Wi-Fi Array with a powerful set of tools and features to optimally tune and verify an 802.11n 22 Introduction Wi-Fi Array installation, as well as give IT administrators the ability to troubleshoot issues that may occur within the wireless environment. The 802.11n standard will continue to evolve over the next several years with additional performance and optional functions, along with ongoing stream of IEEE 802.11 amendments. This changing wireless landscape mandates that appropriate tools are available to the user to analyze, optimize, and troubleshoot their changing environments. The distributed architecture of the Array enables the execution of powerful wireless and networking analysis at the edge of the network where packets traverse the wireless-to-wired boundary. The Array includes an embedded Wi-Fi Controller with the necessary computing and memory resources to provide these functions securely at the network's edge. The key elements of the RAM package include: RF Analysis – An embedded Spectrum Analyzer leverages the dedicated threat sensor radio in each Wi-Fi Array to provide a continual view of utilization, interference, and errors across all available Wi-Fi channels. Packet Analysis – Integrated packet capture provides filterable views of all traffic traversing on the wired and wireless interfaces of the Array. Performance Analysis – Embedded traffic generation enables the throughput of the Array’s wireless or wired interfaces to be analyzed. Failure Recovery – Radio Assurance provides an automatic self-test and self healing mechanism that ensures continuous system operation. Netflow Support Network Tools: ping, RADIUS ping, traceroute Product Specifications — XR4400 and XR4800 Series Introduction 23 Wi-Fi Array ??xxx Please review VERRRRRY carefully!! Element Number of Users XR4000 Series Specifications Maximum of 96 associated users per radio XR48xx: 768 users per Array XR44xx: 384 users per Array Physical Diameter: 12.58 inches (31.95 cm) Height: 2.58 inches (6.55 cm) Weight: 4lbs (1.81 kg) Environmental Operating Temperature: 0°C to 55°C 0% to 90% relative humidity (non-condensing) Storage Temperature: -20°C to 60°C 5% to 95% relative humidity (non-condensing) System 700 MHz CPU 1 GB RAM 1 GB system flash Integrated Switch 2.1 Gbps integrated wireless switch Chassis Lockable mounting plate, Kensington lock slot Electrical PoGE (DC) Input Power: Power over Gigabit Ethernet — no splitter required, 48VDC, Maximum 2A Nominal Power: XR48xx: 60W XR44xx: 35W See “Power over Gigabit Ethernet Compatibility Matrix” on page 451. 24 Introduction Wi-Fi Array Element Interfaces XR4000 Series Specifications Serial Console Port: 1 x RS232 – RJ45 connector, for local configuration Ethernet Interfaces: 2 x Gigabit 100/1000 Mbps uplink ports for link aggregation, redundancy, or bridging 1 x Fast Ethernet 10/100 Mbps, for out of band management Status LEDs: System status, Ethernet, Radio Networking DHCP client, DHCP server (multiple DHCP pools), DNS Client, NTP client, NAT Management Xirrus Management System (XMS) — Layer 3 Element Management System HTTPS Web Management Interface (WMI) CLI via SSHv2, Telnet, local serial Console Enable/disable management for any interface Read-write and read-only admin accounts may be authenticated via RADIUS SNMP v2c, v3 Configuration Files — text-based files may be imported, exported, or compared NetFlow — IP flow information (traffic statistics may be sent to an external Collector FTP, TFTP Syslog reporting for alerts/alarms — messages may be stored on internal Syslog server or sent to up to three external syslog servers. Cisco Discovery Protocol (CDP) — obtain protocol addresses and platform information for neighboring devices Introduction 25 Wi-Fi Array Element Quality of Service (QoS) Support XR4000 Series Specifications Multiple SSIDs: 16 unique SSIDs per Array Each SSID beacons a unique BSSID per radio VLAN and QoS settings for each SSID VLANs: Up to 16 VLANs, 802.1Q, 802.1p Prioritization: 802.11e wireless prioritization 802.1p wired prioritization Fair queuing of downstream traffic Wireless Voice Support 26 Introduction Wi-Fi Array Element Security XR4000 Series Specifications Wireless Encryption Line speed, hardware-accelerated encryption modes: WPA TKIP WPA2 AES WEP 40/64 WEP 104/128 Wireless Authentication: Open Pre-shared Key 802.1X EAP PEAP EAP-TLS EAP-TTLS EAP-LEAP Pass-through Web Page Redirect (Captive Portal) MAC Address Access Control List (ACL) CHAP, PAP Firewall: Integrated stateful-inspection, rules-based firewall Rogue AP detection and blocking: Integrated Rogue AP detection and alerting via dedicated internal RF Threat Sensor. Rogue AP can be shielded Integrated RADIUS Server: Integrated 802.1x Authentication Server supporting EAP-PEAP Introduction 27 Wi-Fi Array Element Security (continued) XR4000 Series Specifications Time of Day Access: Specify when access is allowed, per SSID or User Group Station-Station Blocking: Station-to-Station traffic blocking option Wireless Wireless Standards: 802.11a 802.11b 802.11d 802.11g 802.11e 802.11h 802.11i 802.11j 802.11n Number of Radios: ??OK?? XR48xx: 4 x 802.11a/n radios 4 x 802.11a/b/g/n radios Advanced RF design includes 36 integrated antennas XR44xx: 4 x 802.11a/b/g/n radios Advanced RF design includes 20 integrated antennas Spectrum Analyzer: 1 integrated into Array 28 Introduction Wi-Fi Array Element Wireless (continued) XR4000 Series Specifications Frequency Bands: 11a/n: 4.945 – 4.985 (restricted Public Safety band) 11a/n: 5.15-5.25 GHz (UNII 1) 11a/n: 5.15-5.25 GHz (TELEC) 11a/n: 5.25-5.35 GHz (UNII 2) 11a/n: 5.470-5.725 (ETSI) 11a/n: 5.725-5.825 GHz (UNII 3) 11b/g/n: 2.412-2.462 GHz (FCC) 11b/g/n: 2.412-2.472 GHz (ETSI) 11b/g/n: 2.412-2.484 GHz (TELEC) Channel Selection: Manual and Automatic 802.11a/n Antennas Integrated 6dBi, sectorized 802.11b/g/n Antennas Integrated 3dBi, sectorized Wi-Fi Monitoring: 1 Integrated Access Point can be set as a dedicated Wi-Fi Threat Sensor 2 dBi 360° omni-directional antenna 802.11a/b/g/n External Antenna Connectors: 3 RP-TNC connectors (NOTE: TNC antenna connection is not for outside plant connection.) Performance Client Load Balancing Automatic load balancing between system radios Introduction 29 Wi-Fi Array Element Compliance XR4000 Series Specifications Electromagnetic: ICES-003 (Canada) EN 301.893 (Europe) EN 301.489-1 and -17 (Europe) Safety: EN 60950 EN 50371 to 50385 CE Mark Additional information in “Appendix F: Notices” on page 467. Certifications Wi-Fi Alliance: 802.11a/b/g/n, WPA, WPA2, and extended EAP types. Our certifications may be viewed here. Additional information in “Appendix F: Notices” on page 467. Warranty Hardware: Five Year Standard (extendable) Software: 90 Days Standard (extendable) 30 Introduction Wi-Fi Array Product Specifications — XN16, XN12, and XN8 Element Number of Users XN16/XN12/XN8 Specifications Maximum of 96 associated users per radio XN16: 1536 users per Array XN12: 1152 users per Array XN8: 768 users per Array Physical Diameter: 18.65 inches (47.37 cm) Height: 3.87 inches (9.83 cm) Weight: 10 lbs (3.63 kg) Environmental Operating Temperature: 0°C to 55°C 0% to 90% relative humidity (non-condensing) Storage Temperature: -20°C to 60°C 5% to 95% relative humidity (non-condensing) System 1 GHz CPU 1 GB RAM 1 GB system flash Integrated Switch 2.1 Gbps integrated wireless switch Chassis Lockable mounting plate, Kensington lock slot Introduction 31 Wi-Fi Array Element Electrical XN16/XN12/XN8 Specifications XN8, XN12, XN16 powered by PoGE only PoGE (DC) Input Power: Power over Gigabit Ethernet — no splitter required, 48VDC, Maximum 2A Nominal Power: XN16: 90W XN12: 75W XN8: 60W All Models: For PoGE, see “Power over Gigabit Ethernet Compatibility Matrix” on page 451. Interfaces Serial Console Port: 1 x RS232 – RJ45 connector, for local configuration Ethernet Interfaces: 2 x Gigabit 100/1000 Mbps uplink ports for link aggregation, redundancy, or bridging 1 x Fast Ethernet 10/100 Mbps, for out of band management Status LEDs: System status, Ethernet, Radio Networking 32 DHCP client, DHCP server (multiple DHCP pools), DNS Client, NTP client, NAT Introduction Wi-Fi Array Element Management XN16/XN12/XN8 Specifications Xirrus Management System (XMS) — Layer 3 Element Management System HTTPS Web Management Interface (WMI) CLI via SSHv2, Telnet, local serial Console Enable/disable management for any interface Read-write and read-only admin accounts may be authenticated via RADIUS SNMP v2c, v3 Configuration Files — text-based files may be imported, exported, or compared NetFlow — IP flow information (traffic statistics may be sent to an external Collector FTP, TFTP Syslog reporting for alerts/alarms — messages may be stored on internal Syslog server or sent to up to three external syslog servers. Cisco Discovery Protocol (CDP) — obtain protocol addresses and platform information for neighboring devices Quality of Service (QoS) Support Multiple SSIDs: 16 unique SSIDs per Array Each SSID beacons a unique BSSID per radio VLAN and QoS settings for each SSID VLANs: Up to 16 VLANs, 802.1Q, 802.1p Prioritization: 802.11e wireless prioritization 802.1p wired prioritization Fair queuing of downstream traffic Wireless Voice Support Introduction 33 Wi-Fi Array Element Security XN16/XN12/XN8 Specifications Wireless Encryption Line speed, hardware-accelerated encryption modes: WPA TKIP WPA2 AES WEP 40/64 WEP 104/128 Wireless Authentication: Open Pre-shared Key 802.1X EAP PEAP EAP-TLS EAP-TTLS EAP-LEAP Pass-through Web Page Redirect (Captive Portal) MAC Address Access Control List (ACL) CHAP, PAP Firewall: Integrated stateful-inspection, rules-based firewall Rogue AP detection and blocking: Integrated Rogue AP detection and alerting via dedicated internal RF Threat Sensor. Rogue AP can be shielded Integrated RADIUS Server: Integrated 802.1x Authentication Server supporting EAP-PEAP 34 Introduction Wi-Fi Array Element Security (continued) XN16/XN12/XN8 Specifications Time of Day Access: Specify when access is allowed, per SSID or User Group Station-Station Blocking: Station-to-Station traffic blocking option Wireless Wireless Standards: 802.11a 802.11b 802.11d 802.11g 802.11e 802.11h 802.11i 802.11j 802.11n Number of Radios: XN16: 12 x 802.11a/n radios 4 x 802.11a/b/g/n radios Only 12 radios should be used as 802.11a/n radios (i.e., 5 GHz band) concurrently. 48 integrated antennas XN12: 8 x 802.11a/n radios 4 x 802.11a/b/g/n radios 36 integrated antennas XN8: 4 x 802.11a/n radios 4 x 802.11a/b/g/n radios Advanced RF design includes 36 integrated antennas Spectrum Analyzer: 1 integrated into Array Introduction 35 Wi-Fi Array Element Wireless (continued) XN16/XN12/XN8 Specifications Frequency Bands: 11a/n: 4.945 – 4.985 (restricted Public Safety band) 11a/n: 5.15-5.25 GHz (UNII 1) 11a/n: 5.15-5.25 GHz (TELEC) 11a/n: 5.25-5.35 GHz (UNII 2) 11a/n: 5.470-5.725 (ETSI) 11a/n: 5.725-5.825 GHz (UNII 3) 11b/g/n: 2.412-2.462 GHz (FCC) 11b/g/n: 2.412-2.472 GHz (ETSI) 11b/g/n: 2.412-2.484 GHz (TELEC) Channel Selection: Manual and Automatic 802.11a/n Antennas Integrated 6dBi, sectorized 802.11b/g/n Antennas Integrated 3dBi, sectorized Wi-Fi Monitoring: 1 Integrated Access Point can be set as a dedicated Wi-Fi Threat Sensor 2 dBi 360° omni-directional antenna 802.11a/b/g/n External Antenna Connectors: 3 RP-TNC connectors (NOTE: TNC antenna connection is not for outside plant connection.) Performance Client Load Balancing Automatic load balancing between system radios 36 Introduction Wi-Fi Array Element Compliance XN16/XN12/XN8 Specifications Electromagnetic: ICES-003 (Canada) EN 301.893 (Europe) EN 301.489-1 and -17 (Europe) Safety: EN 60950 EN 50371 to 50385 CE Mark Additional information in “Appendix F: Notices” on page 467. Certifications Wi-Fi Alliance: 802.11a/b/g/n, WPA, WPA2, and extended EAP types. Our certifications may be viewed here. Additional information in “Appendix F: Notices” on page 467. Warranty Hardware: Five Year Standard (extendable) Software: 90 Days Standard (extendable) Introduction 37 Wi-Fi Array Product Specifications — XN4 Element XN4 Specifications Number of Users Maximum of 96 associated users per radio, 384 users per XN4 Physical Diameter: 12.58 inches (31.95 cm) Height: 2.58 inches (6.55 cm) Weight: 4lbs (1.81 kg) Environmental Operating Temperature: 0°C to 55°C 0% to 90% relative humidity (non-condensing) Storage Temperature: -20°C to 60°C 5% to 95% relative humidity (non-condensing) System 825 MHz CPU 512 MB RAM 1 GB system flash Integrated Switch 2.1 Gbps integrated wireless switch Chassis Lockable mounting plate, Kensington lock slot Electrical XN4 supports Power over Gigabit Ethernet (PoGE) only, no splitter required PoGE (DC) Input Power: 48VDC, Maximum 2A Nominal Power: 35W For PoGE, see “Power over Gigabit Ethernet Compatibility Matrix” on page 451. 38 Introduction Wi-Fi Array Element Interfaces XN4 Specifications Serial Console Port: 1 x RS232 – RJ45 connector, for local configuration Ethernet Interfaces: 1 x Gigabit 100/1000 Mbps uplink port Status LEDs: System status, Ethernet, Radio Networking DHCP client, DHCP server (multiple DHCP pools), DNS Client, NTP client, NAT Management Xirrus Management System (XMS) — Layer 3 Element Management System HTTPS Web Management Interface (WMI) CLI via SSHv2, Telnet, local serial Console Enable/disable management for any interface Read-write and read-only admin accounts may be authenticated via RADIUS SNMP v2c, v3 Configuration Files — text-based files may be imported, exported, or compared NetFlow — IP flow information (traffic statistics may be sent to an external Collector FTP, TFTP Syslog reporting for alerts/alarms — messages may be stored on internal Syslog server or sent to up to three external syslog servers. Cisco Discovery Protocol (CDP) — obtain protocol addresses and platform information for neighboring devices Introduction 39 Wi-Fi Array Element Quality of Service (QoS) Support XN4 Specifications Multiple SSIDs: 16 unique SSIDs per Array Each SSID beacons a unique BSSID per radio VLAN and QoS settings for each SSID VLANs: Up to 16 VLANs, 802.1Q, 802.1p Prioritization: 802.11e wireless prioritization 802.1p wired prioritization Fair queuing of downstream traffic Wireless Voice Support 40 Introduction Wi-Fi Array Element Security XN4 Specifications Wireless Encryption Line speed, hardware-accelerated encryption modes: WPA TKIP WPA2 AES WEP 40/64 WEP 104/128 Wireless Authentication: Open Pre-shared Key 802.1X EAP PEAP EAP-TLS EAP-TTLS EAP-LEAP Pass-through Web Page Redirect (Captive Portal) MAC Address Access Control List (ACL) CHAP, PAP Firewall: Integrated stateful-inspection, rules-based firewall Rogue AP detection and blocking: Integrated Rogue AP detection and alerting via dedicated internal RF Threat Sensor. Rogue AP can be shielded Integrated RADIUS Server: Integrated 802.1x Authentication Server supporting EAP-PEAP Introduction 41 Wi-Fi Array Element Security (continued) XN4 Specifications Time of Day Access: Specify when access is allowed, per SSID or User Group Station-Station Blocking: Station-to-Station traffic blocking option Wireless Wireless Standards: 802.11a 802.11b 802.11d 802.11g 802.11e 802.11h 802.11i 802.11j 802.11n Number of Radios: 4 x 802.11a/b/g/n radios Advanced RF design includes 20 integrated antennas Spectrum Analyzer: 1 integrated into Array 42 Introduction Wi-Fi Array Element Wireless (continued) XN4 Specifications Frequency Bands: 11a/n: 4.945 – 4.985 (restricted Public Safety band) 11a/n: 5.15-5.25 GHz (UNII 1) 11a/n: 5.15-5.25 GHz (TELEC) 11a/n: 5.25-5.35 GHz (UNII 2) 11a/n: 5.470-5.725 (ETSI) 11a/n: 5.725-5.825 GHz (UNII 3) 11b/g/n: 2.412-2.462 GHz (FCC) 11b/g/n: 2.412-2.472 GHz (ETSI) 11b/g/n: 2.412-2.484 GHz (TELEC) Channel Selection: Manual and Automatic 802.11a/n Antennas Integrated 3dBi, sectorized 802.11b/g/n Antennas Integrated 1dBi, sectorized Wi-Fi Monitoring: 1 Integrated Access Point can be set as a dedicated Wi-Fi Threat Sensor 2 dBi 360° omni-directional antenna 802.11a/b/g/n External Antenna Connectors: 1 RP-TNC connector (NOTE: TNC antenna connection is not for outside plant connection.) Performance Client Load Balancing Automatic load balancing between system radios Introduction 43 Wi-Fi Array Element Compliance XN4 Specifications Electromagnetic: ICES-003 (Canada) EN 301.893 (Europe) EN 301.489-1 and -17 (Europe) Safety: EN 60950 EN 50371 to 50385 CE Mark Additional information in “Appendix F: Notices” on page 467. Certifications Wi-Fi Alliance: 802.11a/b/g/n, WPA, WPA2, and extended EAP types. Our certifications may be viewed here. Additional information in “Appendix F: Notices” on page 467. Warranty Hardware: Five Year Standard (extendable) Software: 90 Days Standard (extendable) 44 Introduction Wi-Fi Array Product Specifications — XS16 and XS8 Element Number of Users XS16/XS8 Specifications Maximum of 64 associated users per radio 1024 users per Array (XS16) 512 users per Array (XS8) Physical Diameter: 18.65 inches (47.37 cm) Height: 3.87 inches (9.83 cm) Weight: 8lbs (3.63 kg) Environmental Operating Temperature: -10°C to 50°C 0% to 90% relative humidity (non-condensing) Storage Temperature: -20°C to 60°C 5% to 95% relative humidity (non-condensing) System 1 GHz CPU 1 GB RAM 1 GB system flash Expansion slot for future options Interfaces Serial: 1 x RS232 – RJ45 connector Ethernet Interfaces: 2 x Gigabit 100/1000 Mbps w/failover 1 x Fast Ethernet 10/100 Mbps Status LEDs: System status, Ethernet, Radio Introduction 45 Wi-Fi Array Element Electrical XS16/XS8 Specifications XS16/XS8: Each Array supports both AC and PoGE AC Input Power: 90-265VAC at 47-63Hz PoGE Input Power: Power over Gigabit Ethernet — no splitter required, 48VDC Nominal Power: XS16: 70W XS8: 45W For PoGE, see “Power over Gigabit Ethernet Compatibility Matrix” on page 451. Networking DHCP client, DHCP server, NTP client, NAT VLAN Support 802.1Q, 802.1p VLAN Supports up to 16 VLANs Multiple SSID Support Performance Allows up to 16 separate SSIDs to be defined with map security, VLAN and QoS settings for each SSID Client Load Balancing Automatic load balancing between system radios Quality of Service: 802.1p wired traffic prioritization Wireless packet prioritization MAP CoS to TCID Fair queuing of downstream traffic 46 Introduction Wi-Fi Array Element Security XS16/XS8 Specifications Wireless Security: WEP 40bit/128bit encryption WPA and WPA2 with TKIP and AES encryption Rogue AP detection, with alerts and classification User and System Authentication: WPA and WPA2 Pre-Shared Key authentication Internal RADIUS Server, supports EAP-PEAP only 802.1x EAP-TLS 802.1x EAP-TTLS/MSCHAPv2 802.1x PEAPv0/EAP-MSCHAPv2 802.1x PEAPv1/EAP-GTC 802.1x EAP-SIM 802.1x EAP-LEAP Passthrough External RADIUS servers Authentication of Wi-Fi Arrays to the Xirrus Management System (XMS) Introduction 47 Wi-Fi Array Element Wireless XS16/XS8 Specifications Number of Radios: 12 x 802.11a radios 4 x 802.11a/b/g radios Only 12 radios should be used as 802.11a radios concurrently. XS16: XS8: 4 x 802.11a radios 4 x 802.11a/b/g radios Wireless Standards: 802.11a/b/g and g-only mode 802.11e, 802.11i Channel Selection: Manual and Automatic Frequency Bands: 11a: 4.945 – 4.985 (restricted Public Safety band) 11a: 5.15-5.25 GHz (UNII 1) 11a: 5.15-5.25 GHz (TELEC) 11a: 5.25-5.35 GHz (UNII 2) 11a: 5.470-5.725 (ETSI) 11a: 5.725-5825 GHz (UNII 3) 11b/g: 2.412-2.462 GHz (FCC) 11b/g: 2.412-2.472 GHz (ETSI) 11b/g: 2.412-2.484 GHz (TELEC) Antennas (XS16): 12 x internal 6 dBi 60° 802.11a sectorized 4 x internal 3 dBi 180° 802.11b/g sectorized 1 x internal 2 dBi 360° omni-directional (for RF monitoring) 3 x external RP-TNC connectors for three 802.11a/ b/g radios * 48 Introduction Wi-Fi Array Element Wireless (continued) XS16/XS8 Specifications Antennas (XS8): 4 x internal 6 dBi 60° 802.11a sectorized 4x internal 3 dBi 180° 802.11b/g sectorized 1 x internal 2 dBi 360° omni-directional (for RF monitoring) 3 x external RP-TNC connectors for three 802.11a/ b/g radios * Radio Approvals: FCC (United States) and EN 301.893 (Europe) * Note: External RP-TNC antenna connectors are not for outside plant connection. Management Web-based HTTPS SNMP v2c, v3 CLI via SSHv2 or Telnet FTP TFTP Serial Xirrus Management System (XMS) Syslog reporting for alerts/alarms Compliance UL / cUL 60950 and EN 60950 FCC Part 15.107 and 15109, Class A EN 301.489 (Europe) EN60601 EU medical equipment directive for EMC Additional information in “Appendix F: Notices” on page 467. Introduction 49 Wi-Fi Array Element Certifications XS16/XS8 Specifications Wi-Fi Alliance: 802.11a/b/g, WPA, WPA2, and extended EAP types. Our certifications may be viewed here. Federal Information Processing Standard (FIPS) Publication 140 -2, Level 2. Payment Card Industry Data Security Standard (PCI DSS) verified by VeriSign Additional information in “Appendix F: Notices” on page 467. Warranty 50 One year (hardware and software) Introduction Wi-Fi Array Product Specifications — XS4 Element XS4 Specifications Number of Users Maximum of 64 associated users per radio (256 users per Array) Physical Diameter: 12.58 inches (31.95 cm) Height: 2.58 inches (6.55 cm) Weight: 4lbs (1.81 kg) Environmental Operating Temperature: -10°C to 50°C 0% to 90% relative humidity (non-condensing) Storage Temperature: -20°C to 60°C 5% to 95% relative humidity (non-condensing) System 825 MHz CPU (XS4) 512 MB RAM, expandable (XS4) 512 MB system flash, expandable Expansion slot for future options Electrical XS4: Each Array supports both AC and PoGE AC Input Power: 90-265VAC at 47-63Hz Nominal power usage: 27W Power over Gigabit Ethernet (PoGE): all 4-port models work with all Xirrus PoGE modules, splitter required, 48VDC See “Power over Gigabit Ethernet Compatibility Matrix” on page 451. Introduction 51 Wi-Fi Array Element Interfaces XS4 Specifications Serial: 1 x RS232 – RJ45 connector Ethernet Interfaces: 1 x Gigabit 100/1000 Mbps Status LEDs: System status, Ethernet, Radio Management Web-based HTTPS SNMP v2c, v3 CLI via SSHv2 or Telnet FTP TFTP Serial Xirrus Management System (XMS) Syslog reporting for alerts/alarms Networking DHCP client, DHCP server, NTP client, NAT VLAN Support 802.1Q, 802.1p VLAN Supports up to 16 VLANs Multiple SSID Support Allows up to 16 separate SSIDs to be defined with map security, VLAN and QoS settings for each SSID Performance Client Load Balancing Automatic load balancing between system radios Quality of Service: 802.1p wired traffic prioritization Wireless packet prioritization MAP CoS to TCID Fair queuing of downstream traffic 52 Introduction Wi-Fi Array Element Security XS4 Specifications Wireless Security: WEP 40bit/128bit encryption WPA and WPA2 with TKIP and AES encryption Rogue AP detection, with alerts and classification User and System Authentication: WPA Pre-Shared Key authentication Internal RADIUS Server, supports EAP-PEAP only 802.1x EAP-TLS 802.1x EAP-TTLS/MSCHAPv2 802.1x PEAPv0/EAP-MSCHAPv2 802.1x PEAPv1/EAP-GTC 802.1x EAP-SIM 802.1x EAP-LEAP Passthrough External RADIUS servers Authentication of Wi-Fi Arrays to the Xirrus Management System (XMS) Introduction 53 Wi-Fi Array Element Wireless XS4 Specifications Number of Radios: 4 x 802.11a/b/g radios Wireless Standards: 802.11a/b/g and g-only mode 802.11e, 802.11i Channel Selection: Manual and Automatic Frequency Bands: 11a: 4.945 – 4.985 (restricted Public Safety band) 11a: 5.15-5.25 GHz (UNII 1) 11a: 5.15-5.25 GHz (TELEC) 11a: 5.25-5.35 GHz (UNII 2) 11a: 5.470-5.725 (ETSI) 11a: 5.725-5825 GHz (UNII 3) 11b/g: 2.412-2.462 GHz (FCC) 11b/g: 2.412-2.472 GHz (ETSI) 11b/g: 2.412-2.484 GHz (TELEC) Radio Approvals: FCC (United States) and EN 301.893 (Europe) Compliance UL / cUL 60950 and EN 60950 FCC Part 15.107 and 15109, Class A EN 301.489 (Europe) EN60601 EU medical equipment directive for EMC Additional information in “Appendix F: Notices” on page 467. 54 Introduction Wi-Fi Array Element Certifications XS4 Specifications Wi-Fi Alliance: 802.11a/b/g, WPA, WPA2, and extended EAP types. Our certifications may be viewed here. Federal Information Processing Standard (FIPS) Publication 140 -2, Level 2. Payment Card Industry Data Security Standard (PCI DSS) verified by VeriSign Additional information in “Appendix F: Notices” on page 467. Warranty Introduction One year (hardware and software) 55 Wi-Fi Array 56 Introduction Wi-Fi Array Installing the Wi-Fi Array The instructions for completing a successful installation include the following topics: “Installation Prerequisites” on page 57. “Planning Your Installation” on page 60. “Installation Workflow” on page 94. “Installing Your Wi-Fi Array” on page 96. “Powering Up the Wi-Fi Array” on page 100. “Establishing Communication with the Array” on page 103. “Performing the Express Setup Procedure” on page 106. Installation Prerequisites Your Wi-Fi Array deployment requires the presence of hardware and services in the host wired/wireless network, including: Power Source Most Arrays are powered via Xirrus Power over Gigabit Ethernet. PoGE supplies power over the same Cat 5e or Cat 6 cable used for data, thus reducing cabling and installation effort. PoGE power injector modules are available in 1-, 2-, and 8-port configurations and are typically placed near your Gigabit Ethernet switch. An AC outlet is required for each injector module. Current Array models have integrated splitters, so no separate splitter is required. Specific models of the Array are compatible with specific PoGE modules. For details, please see “Power over Gigabit Ethernet Compatibility Matrix” on page 451. If your Arrays are equipped to accept AC power (and you are not using PoGE), you need a dedicated power outlet to supply AC power to each unit deployed at the site. Installing the Wi-Fi Array 57 Wi-Fi Array Ethernet port You need at least one 100/1000 BaseT port to establish wired Gigabit Ethernet connectivity (via the product’s Gigabit 1 or Gigabit 2 port) and one 10/100 BaseT port (if desired) for product management. The Array’s Ethernet ports should be connected to an Ethernet switch, not an Ethernet hub — if a hub is used, we recommend that you connect only one Ethernet port. The Gigabit1 Ethernet interface is the primary port for both data and management traffic. If a single Ethernet connection is used, it must be connected to the Gigabit1 Ethernet interface. See also, “Port Failover Protection” on page 80. The 10/100 Ethernet Port may be used for managing the Array out of band from the Gigabit Ethernet ports. The 10/100 port will route only management traffic, using a static route that may be configured for this interface. See “interface” on page 370. Secure Shell (SSH) utility To establish secure remote command line access to the Array, you need a Secure Shell (SSH) utility, such as PuTTY. The utility must be configured to use SSH-2, since the Array will only allow SSH-2 connections. Secure Web browser Either Internet Explorer (version 6.0 or higher), Netscape Navigator (version 7.0 or higher), or Mozilla Firefox (version 1.01 or higher). A secure Web browser is required for Web-based management of the Array. The browser must be on the same subnet as the Array, or you must set a static route for management as described in the warning above. 58 Serial connection capability To connect directly to the console port on the Array, your computer must be equipped with a male 9-pin serial port and terminal emulation software (for example, HyperTerminal). The Xirrus Array only supports serial cable lengths up to 25’ per the RS-232 specification. Installing the Wi-Fi Array Wi-Fi Array Use the following settings when establishing a serial connection: Bits per second 115,200 Data bits Parity None Stop bits Flow control None Optional Network Components The following network components are optional. Xirrus Management System (XMS) The optional XMS offers powerful management features for small or large Wi-Fi Array deployments. External RADIUS server Although your Array comes with an embedded RADIUS server, for 802.1x authentication in large deployments you may want to add an external RADIUS server. Client Requirements The Wi-Fi Array should only be used with Wi-Fi certified client devices. See Also Coverage and Capacity Planning Deployment Examples Failover Planning Planning Your Installation Installing the Wi-Fi Array 59 Wi-Fi Array Planning Your Installation This section provides guidelines and examples to help you plan your Xirrus Wi-Fi Array deployment to achieve the best overall coverage and performance. We recommend you conduct a site survey to determine the best location and settings for each Array you install. The following topics are discussed: “General Deployment Considerations” on page 60 “Coverage and Capacity Planning” on page 62 “IEEE 802.11n Deployment Considerations” on page 72 “Failover Planning” on page 80 “Power Planning” on page 82 “Security Planning” on page 83 “Port Requirements” on page 86 “Network Management Planning” on page 89 “WDS Planning” on page 90 “Common Deployment Options” on page 93 For a complete discussion of implementing Voice over Wi-Fi on the Array, see the Xirrus Voice over Wi-Fi Application Note in the Xirrus Library. General Deployment Considerations The Wi-Fi Array’s unique multi-radio architecture generates 360 degrees of sectored high-gain 802.11a/b/g/n or 802.11a/b/g coverage that provides extended range. However, the number, thickness and location of walls, ceilings or other objects that the wireless signals must pass through may affect the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise at your location. To maximize wireless range, follow these basic guidelines: 1. 60 Keep the number of walls and ceilings between the Array and your receiving devices to a minimum — each wall or ceiling can reduce the Installing the Wi-Fi Array Wi-Fi Array wireless range from between 3 and 90 feet (1 to 30 meters). Position your devices so that the number of walls or ceilings is minimized. 2. Be aware of the direct line between each device. For example, a wall that is 1.5 feet thick (half a meter) at 90° is actually almost 3 feet thick (or 1 meter) when viewed at a 45° angle. At an acute 2° degree angle the same wall is over 42 feet (or 14 meters) thick! For best reception, try to ensure that your wireless devices are positioned so that signals will travel straight through a wall or ceiling. 90° 45° 2° > 42 feet\ 14 m 1.5 feet/ .5 m ~ 3 feet/ 1m Figure 10. Wall Thickness Considerations 3. Try to position wireless client devices so that the signal passes through drywall (between studs) or open doorways and not other materials that can adversely affect the wireless signal. See Also Coverage and Capacity Planning Deployment Examples Common Deployment Options Installation Prerequisites Installing the Wi-Fi Array 61 Wi-Fi Array Coverage and Capacity Planning This section considers coverage and capacity for your deployment(s), including placement options, RF patterns and cell sizes, area calculations, roaming considerations, and channel allocations. Note that several advanced features in this section are part of the Xirrus Advanced RF Performance Manager (RPM). They require the license installed on the Array to include support for RPM. Please see “About Licensing and Upgrades” on page 325. Placement Use the following guidelines when considering placement options: 1. The best placement option for the Array is ceiling-mounted within an open plan environment (cubicles rather than fixed walls). 2. Keep the Array away from electrical devices or appliances that generate RF noise. Because the Array is generally mounted on ceilings, be aware of its position relative to lighting (especially fluorescent lighting) — we recommend maintaining a distance of at least 3 to 6 feet (1 to 2 meters). 100 ft/ 30m 100 ft/ 30 m 100 ft/ 30 m Figure 11. Unit Placement 62 Installing the Wi-Fi Array Wi-Fi Array 3. If using multiple Arrays in the same area, maintain a distance of at least 100ft/30m between Arrays if there is direct line-of-sight between units, or at least 50ft/15m if a wall or other barrier exists between units. RF Patterns The Wi-Fi Array allows you to control — automatically or manually — the pattern of wireless coverage that best suits your deployment needs. You can choose to operate with full coverage, half coverage, or custom coverage (by enabling or disabling individual sectors). Full (Normal) Coverage In normal operation, the Array provides a full 360 degrees of coverage. Figure 12. Full (Normal) Coverage Half Coverage If installing a unit close to an exterior wall, you can deactivate half of the radios to prevent redundant signals from “bleeding” beyond the wall and extending Installing the Wi-Fi Array 63 Wi-Fi Array service into public areas. The same principle applies if you want to restrict service to an adjacent room within the site. outside wall Figure 13. Adjusting RF Patterns Custom Coverage Where there are highly reflective objects in proximity to the Array, you can turn off specific radios to avoid interference and feedback. reflective object Figure 14. Custom Coverage 64 Installing the Wi-Fi Array Wi-Fi Array Capacity and Cell Sizes Cell sizes should be estimated based on the number of users, the applications being used (for example, data/video/voice), and the number of Arrays available at the location. The capacity of a cell is defined as the minimum data rate desired for each sector multiplied by the total number of sectors being used. Figure 15. Connection Rate vs. Distance Figure 15 shows relative connection rates for 802.11n vs. 802.11a/g and 802.11b, and the effect of distance on the connection rates. Wireless environments can vary greatly so the actual rates may be different depending on the specific network deployment. The XS4 and XN4 have a smaller range than the larger Arrays. Installing the Wi-Fi Array 65 Wi-Fi Array Fine Tuning Cell Sizes Adjusting the transmit power allows you to fine tune cell sizes. There are four standard sizes — Small, Medium, Large, or Max (the default is Max). There is also an Auto setting that automatically determines the best cell size, and a Manual setting that allows you to choose your power settings directly. Small Medium Large Figure 16. Transmit Power Auto Cell Size is an automatic, self-tuning mechanism that balances cell size between Arrays to guarantee coverage while limiting the RF energy that could extend beyond the organizational boundary. Auto Cell uses communication between Arrays to dynamically set radio power so that complete coverage is provided to all areas, yet at the minimum power level required. This helps to minimize potential interference with neighboring networks. Additionally, Arrays running Auto Cell automatically detect and compensate for coverage gaps caused by system interruptions. To enable the Auto Cell Size feature, go to “RF Power & Sensitivity” on page 298. For a complete discussion of the Auto Cell size feature, see the Xirrus Auto Cell Application Note in the Xirrus Library. If you are installing many units in proximity to each other, we recommend that you use Auto Cell Size; otherwise, reduce the transmit power using manual settings to avoid excessive interference with other Arrays or installed APs. See also, “Coverage and Capacity Planning” on page 62. 66 Installing the Wi-Fi Array Wi-Fi Array Sharp Cell This patented Xirrus RF management option automatically creates more intelligently defined cells and improves performance by creating smaller, highthroughput cells. By dynamically limiting each cell to a defined boundary (cell size), the trailing edge bleed of RF energy is reduced, thus minimizing interference between neighboring Wi-Fi Arrays or other Access Points. To enable the Sharp Cell feature, go to “RF Power & Sensitivity” on page 298. For more information about this feature, see the Xirrus Sharp Cell Application Note in the Xirrus Library. Roaming Considerations Cells should overlap approximately 10 - 15% to accommodate client roaming. ROAMING 10 - 15% overlap Figure 17. Overlapping Cells Allocating Channels Because the Wi-Fi Array is a multi-channel device, allocating the best channels to radios is important if peak performance is to be maintained. Automatic Channel Selection We recommend that you allow the Array to make intelligent channel allocation decisions automatically. In the automatic mode, channels are allocated dynamically, driven by changes in the environment. Auto Channel assignment is Installing the Wi-Fi Array 67 Wi-Fi Array performed by scanning the surrounding area for RF activity on all channels, then automatically selecting and setting channels on the Array to the best channels available. This function is typically executed when initially installing Arrays in a new location and may optionally be configured to execute periodically to account for changes in the RF environment over time. Auto Channel selection has significant advantages, including: Allows the Array to come up for the first time and not interfere with existing equipment that may be already running, thereby limiting cochannel interference. More accurately tunes the RF characteristics of a Wi-Fi installation than manual configuration since the radios themselves are scanning the environment from their physical location. May be configured to run periodically. To set up the automatic channel selection feature, go to “Advanced RF Settings” on page 294. For more information about this feature, see the Xirrus Auto Channel Application Note in the Xirrus Library. 68 Installing the Wi-Fi Array Wi-Fi Array Manual Channel Selection You can manually assign channels on a per radio basis, though manual selection is not recommended (and not necessary). To avoid co-channel interference, do not select adjacent channels for radios that are physically next to each other. Maintain channel separation Figure 18. Allocating Channels Manually See Also Deployment Examples Failover Planning Installation Prerequisites Installing the Wi-Fi Array 69 Wi-Fi Array Deployment Examples The following examples employ 802.11a cells, each offering minimum throughputs of 54 Mbps, 36 Mbps, and 18 Mbps per sector respectively, and assume a floor plan covering a total area of about 60,000 square feet (5574 sq m). Figure 19. Deployment Scenario (54 Mbps) — Per Sector Figure 20. Deployment Scenario (36 Mbps) — Per Sector 70 Installing the Wi-Fi Array Wi-Fi Array Figure 21. Deployment Scenario (18 Mbps) — Per Sector See Also Coverage and Capacity Planning Failover Planning Planning Your Installation Installing the Wi-Fi Array 71 Wi-Fi Array IEEE 802.11n Deployment Considerations IEEE 802.11n features are supported only on XR and XN Array models, and this section applies only to those Arrays. Note that the license installed on the Array must include support for 802.11n. Please see “About Licensing and Upgrades” on page 325. The Xirrus XR and XN Arrays support IEEE 802.11n on all IAPs, in both 2.4 GHz and 5 GHz bands. Use of 802.11n offers significant benefits: Higher data rates Higher throughput Supports more users More robust connections Increased coverage area More secure connections — supports WPA2 (Wi-Fi Protected Access 2) These benefits result in better support for a wide range of applications such as voice and video, intensive usage such as CAD/CAM and backups, dense user environments, and for manufacturing and warehousing environments. While 802.11n increases coverage area by almost doubling the reach, you must consider the legacy wireless devices in your network. Wireless stations connecting using 802.11a/b/g will still be subject to a reach of up to 100 feet, depending on the environment. The techniques that 802.11n uses to realize these performance improvements, and the results that can be expected are discussed in: 72 “MIMO (Multiple-In Multiple-Out)” on page 73 “Multiple Data Streams — Spatial Multiplexing” on page 75 “Channel Bonding” on page 76 “Improved MAC Throughput” on page 77 “Short Guard Interval” on page 77 “Obtaining Higher Data Rates” on page 78 “802.11n Capacity” on page 79 Installing the Wi-Fi Array Wi-Fi Array Two very important techniques to consider are Channel Bonding and Multiple Data Streams — Spatial Multiplexing because they contribute a large portion of 802.11n’s speed improvements and because they are optional and configurable, as opposed to the parts of 802.11n that are fixed. While the settings for 802.11n IAPs come pre-configured on the Array for robust performance in typical usage, you should review the settings for your deployment, especially channel bonding. A global setting is provided to enable or disable 802.11n mode. See “Global Settings .11n” on page 291 to configure 802.11n operation. MIMO (Multiple-In Multiple-Out) MIMO (Multiple-In Multiple-Out) signal processing is one of the core technologies of 802.11n. It mitigates interference and maintains broadband performance even with weak signals. Prior to 802.11n, a data stream was transmitted via one antenna. At the receiving end, the antenna with the best signal was selected to receive data. (Figure 22) Figure 22. Classic 802.11 Signal Transmission Installing the Wi-Fi Array 73 Wi-Fi Array MIMO Processed Signal Antenna 1 Signal Attenuation Receiver Antenna 2 Signal Antenna 3 Signal Frequency Across Subcarriers Figure 23. MIMO Signal Processing MIMO signal processing uses multiple antennas to send and receive data. It takes advantage of multipath reflections to improve signal coherence and greatly increase receiver sensitivity (Figure 23). Multipath signals were considered to be interference by 802.11a/b/g radios, and degraded performance. In 802.11n, these signals are used to enhance performance. This extra sensitivity can be used for greater range or higher data rates. The enhanced signal is the processed sum of individual antennas. Signal processing eliminates nulls and fading that any one antenna would see. MIMO signal processing is sophisticated enough to discern multiple spatial streams (see Multiple Data Streams — Spatial Multiplexing). There are no settings to configure for MIMO. 74 Installing the Wi-Fi Array Wi-Fi Array Multiple Data Streams — Spatial Multiplexing Spatial Multiplexing transmits completely separate data streams on different antennas (in the same channel) that are recombined to produce new 802.11n data rates. Higher data rates are achieved by splitting the original data stream into separate data streams. Each separate stream is transmitted on a different antenna (using its own RF chain). MIMO signal processing at the receiver can detect and recover each stream. Streams are then recombined, yielding higher data rates. Data Stream Tx 1 Rx 1 Tx 2 Rx 2 Transmitter Tx N Receiver Data Stream Rx M Figure 24. Spatial Multiplexing Spatial multiplexing can double, triple, or quadruple the date rate, depending on the number of transmit antennas used. You can configure the number of chains (i.e., streams) separately for transmitting and receiving. By default, the Array uses three chains for transmitting and receiving (see “Global Settings .11n” on page 291). Installing the Wi-Fi Array 75 Wi-Fi Array Channel Bonding Channel bonding increases data rates by combining two adjacent 20 MHz channels into one 40 MHz channel. This increases the data rate to slightly more than double. A bonded 40 MHz channel is specified in terms of the Primary channel and the adjacent channel to Bond. The Bond channel is represented by +1 to use the channel above the Primary channel, or -1 to use the channel below. In the example shown, Channel 40 is the Primary channel and it is bonded to Channel 36, the channel below it, by specifying -1. Be aware that Channel Bonding can make channel planning more difficult, since you are using two channels for an IAP. We recommend the use of the 5 GHz band, since it has many more channels than the 2.4 GHz band, and thus more channels are available for bonding. The Array provides an Automatic Channel Bonding setting that will automatically select the best channel for bonding on each IAP. If you enable this option, you may select whether bonding will be dynamic (the bonded channel changes in response to environmental conditions) or static (the bonded channel will not be changed. See “Global Settings .11n” on page 291. To configure channel bonding manually, on a per-IAP basis, see “IAP Settings” on page 271. Ch# 36 Ch# (40, -1) 40 20 MHz 20 MHz Standard 802.11 channels are effectively 20MHz wide. 40 MHz Channel bonding combines two adjacent 20MHz channels into a single 40MHz channel providing increased throughput. Figure 25. Channel Bonding 76 Installing the Wi-Fi Array Wi-Fi Array Improved MAC Throughput These changes make 802.11n transmission of MAC frames 40% more efficient than legacy transmission: MAC data frames are combined and given a single PHY header. Implicit Block ACK acknowledges all data frames within a combined frame. Spacing between frames is reduced. Frame Aggregation Legacy Operation Data Frame ACK Frame Data Frame ACK Frame High Throughput Operation Data Frame ACK Frame Data Frame sss PHY Header Block ACK Frame MAC Header sss sss 1 2 Data Frame Payload ACK Frame Payload RIFS Usage (Reduced Inter-Frame Spacing) Legacy Operation Data Frame Data Frame ACK Frame ACK Frame SIFS sss ACK Frame SIFS High Throughput Operation Data Frame Data Frame Data Frame Data Frame sss RIFS Block ACK Request Frame Block ACK Response Frame 1 2 RIFS sss SIFS Figure 26. MAC Throughput Improvements Short Guard Interval This option reduces the wait time between signals that are being sent out over the air. The guard interval provides immunity to propagation delays and reflections, and is normally 800 ns (long). By using a short guard interval (400 ns), the data rate is increased by approximately 11%. The short interval may be used in many environments (especially indoors). If the short guard interval is used in an Installing the Wi-Fi Array 77 Wi-Fi Array inappropriate environment, the signal quality will suffer and throughput will decrease. See “Global Settings .11n” on page 291 to configure the guard interval. Obtaining Higher Data Rates The data rate increase obtained by using 802.11n on an Array is incremental, based on the technologies that are applied and the options that you select: Higher encoding rates (Mandatory in 802.11n) Spatial Streams (Mandatory, but multiplier varies directly with number of streams selected.) Channel Bonding (Mandatory in 802.11n, apply multiplier to IAP if it is bonded.) Short Guard Interval (Optional) See Figure 27 to compute your 802.11n data rate increase for an IAP. Apply this increase to the 802.11 a, b or g data rates selected for the Array. Choose New Base Encoding + Modulation BPSK (6.5) QPSK (13, 19.5) QAM-16 (26, 39) QAM-64 (58.5, 65) Optionally Multiply by 2, 3, 4 for the Number of Additional Spatial Streams Expected 802.11n Data Rates 802.11a 802.11g Rates 12 18 24 36 48 54 11n Mandatory Data Rates 6.5 13 19.5 26 39 52 58.5 65 One Spatial Stream With Channel Bonding (40MHz) 13.5 27 40.5 54 81 108 121.5 135 Optionally Multiply By 2.077 to Bond Two 20MHz Channels Optionally Multiply by 1.11 for Shorter Guard Interval to Increase Symbol Rate New 11n Data Rate Expected First Generation Device Data Rates With Short Guard Interval 15 30 45 60 90 120 135 150 Two Spatial Streams With Channel Bonding (40MHz) 27 54 81 108 162 216 243 270 Two Spatial Streams 13 26 39 52 78 104 117 130 With Short Guard Interval 30 60 90 120 180 240 270 300 Figure 27. Computing 802.11n Data Rates 78 Installing the Wi-Fi Array Wi-Fi Array 802.11n Capacity 802.11n offers major increases in capacity over previous 802.11 standards, as shown in Figure 28. Note that this chart shows figures for 802.11n (with one spatial stream and channel bonding). 802.11a/n Capacity 150 23 channels * 150Mbps = 3.4Gbps 802.11a Capacity 23 channels * 54Mbps = 1.2 Gbps 802.11g/n Capacity 3 channels * 150Mbps = 450 Mbps 802.11g Capacity 3 channels * 54Mbps = 162 Mbps 802.11b Capacity 3 channels * 11Mbps = 33 Mbps Figure 28. 802.11n Increases Capacity Installing the Wi-Fi Array 79 Wi-Fi Array Failover Planning This section discusses failover protection at the unit and port levels. Port Failover Protection To ensure that service is continued in the event of a port failure, you can utilize the Gigabit 1 and Gigabit 2 ports simultaneously. Multiple port connections Ethernet switch Figure 29. Port Failover Protection In addition, the Array has full failover protection between the Gigabit 1 and Gigabit 2 Ethernet ports (see following table). Interface Bridges Data? Bridges Management Traffic? Fails Over To: IP address Fast Ethernet No Yes None DHCP or static Gigabit 1 Yes Yes Gigabit 2 DHCP or static Gigabit 2 Yes Yes Gigabit 1 Assumes the IP address of Gigabit 1 The Wi-Fi Array Gigabit Ethernet ports actually support a number of modes: 80 802.3ad Link Aggregation Installing the Wi-Fi Array Wi-Fi Array Load Balancing Broadcast Link Backup Bridged Mirrored For more details on Gigabit port modes and their configuration, please see “Network Interface Ports” on page 181. Switch Failover Protection To ensure that service is continued in the event of a switch failure, you can connect Arrays to more than one Ethernet switch (not a hub). Ethernet connections Backup switch Ethernet switch Figure 30. Switch Failover Protection Gigabit Ethernet connections must be on the same subnet. See Also Coverage and Capacity Planning Deployment Examples Installation Prerequisites Network Management Planning Planning Your Installation Power Planning Security Planning Installing the Wi-Fi Array 81 Wi-Fi Array Power Planning All XR and XN Series Array models and XS16/8/4 Arrays support Power over Gigabit Ethernet (PoGE) with an integrated splitter. AC power is also supported on some versions of the XS8 and XS16.? True?? This section discusses the AC and PoGE power options. AC Power The AC power option requires a direct connection between the Array and a dedicated AC power outlet. The power cord is provided with the unit. Power over Gigabit Ethernet To deliver power to the Array, you may use the optional XP1, XP2, or XP8 Power over Gigabit Ethernet (PoGE) modules. They provide power over Cat 5e or Cat 6 cables to the Array without running power cables — see Figure 5 on page 14. Specific models of the Array are compatible with specific PoGE modules. For details, please see “Power over Gigabit Ethernet Compatibility Matrix” on page 451. When using Cat 5e or Cat 6 cable, power can be provided up to a distance of 100m. See Also Coverage and Capacity Planning Deployment Examples Failover Planning Network Management Planning Security Planning 82 Installing the Wi-Fi Array Wi-Fi Array Security Planning This section offers some useful guidelines for defining your preferred encryption and authentication method. For additional information, see “Understanding Security” on page 210 and the Security section of “Frequently Asked Questions” on page 432. Note that several advanced features in this section are part of the Xirrus Advanced RF Security Manager (RSM). They require the license installed on the Array to include support for RSM. Please see “About Licensing and Upgrades” on page 325. Wireless Encryption Encryption ensures that no user can decipher another user’s data transmitted over the airwaves. There are three encryption options available to you, including: WEP-40bit or WEP-128bit Because WEP is vulnerable to cracks, we recommend that you only use this for legacy devices that cannot support a stronger encryption type. Wi-Fi Protected Access (WPA) This is much more secure than WEP and uses TKIP for encryption. Wi-Fi Protected Access (WPA2) with AES This is government-grade encryption — available on most new client adapters — and uses the AES–CCM encryption mode (Advanced Encryption Standard–Counter Mode). Authentication Authentication ensures users are who they say they are, and occurs when users attempt to join the wireless network and periodically thereafter. The following authentication methods are available with the Wi-Fi Array: RADIUS 802.1x 802.1x uses a remote RADIUS server to authenticate large numbers of clients, and can handle different authentication methods (EAP-TLS, EAPTTLS, EAP-PEAP, and EAP-LEAP Passthrough). Administrators may Installing the Wi-Fi Array 83 Wi-Fi Array also be authenticated via RADIUS when preferred, or to meet particular security standards. Xirrus Internal RADIUS server Recommended for smaller numbers of users (about 100 or less). Supports EAP-PEAP only Pre-Shared Key Uses a pass-phrase or key that is manually distributed to all authorized users. The same passphrase is given to client devices and entered into each Array. MAC Access Control Lists (ACLs) MAC access control lists provide a list of client adapter MAC addresses that are allowed or denied access to the wireless network, and can be used in addition to any of the above authentication methods. ACLs are good for embedded devices, like printers and bar-code scanners (though MAC addresses can be spoofed). The Array supports 1,000 ACL entries. Meeting PCI DSS Standards The Payment Card Industry (PCI) Data Security Standard (DSS) was developed by major credit card companies. It lays out a set of requirements that must be met in order to provide adequate security for sensitive data. The Wi-Fi Array may be configured to satisfy PCI DSS standards. For details, please see Appendix D: Implementing PCI DSS. Note that the license installed on the Array must include the Xirrus Advanced RF Security Manager (RSM) to support PCI audit compliance enforcement. Please see “About Licensing and Upgrades” on page 325. Meeting FIPS Standards The Federal Information Processing Standard (FIPS) Publication 140-2 establishes a computer security standard used to accredit cryptographic modules. The standard is a joint effort by the U.S. and Canadian governments. To implement Level 2 security requirements of FIPS Level 2 on the Wi-Fi Array, see Appendix E: Implementing FIPS Security. 84 Installing the Wi-Fi Array Wi-Fi Array See Also Failover Planning Network Management Planning Power Planning Installing the Wi-Fi Array 85 Wi-Fi Array Port Requirements A number of ports are used by various Array features and by the Xirrus Management System (XMS). The Port Requirements table on page 87 lists ports and the features that require them (XMS port requirements are included in the table for your convenience). If you are using a feature, please make sure that the ports that it requires are not blocked by firewalls or other policies, and that they do not conflict with any other port assignments. As an example, XMS port requirements are illustrated in Figure 31. XMS requires ports 161, 162, and 443 to be passed between Arrays and the XMS server. Similarly, ports 9090 and 9091 are required for communication between the XMS server and XMS clients, and port 25 is typically used by the XMS server to access an SMTP server to send email notifications. SSID Traffic on VLANs A, B, etc. Management over Native VLAN Internal Resources Trunked 802.1q VLAN Connection Traffic from Arrays VLAN A Traffic from Arrays VLAN B L2 Switching Infrastructure External Network / Internet Firewall XMS Server Ports: 161, 162, 443 XMS Client* SMTP Server* Ports: 9090, 9091 Ports: 25 * XMS Client and SMTP Server may be internal or external resources. Figure 31. Port Requirements for XMS 86 Installing the Wi-Fi Array Wi-Fi Array The following table lists port requirements for the Array and for XMS, how they are used, and whether they may be changed. Port Application Peer Configurable Array 20 tcp 21 udp FTP Client Yes 22 tcp SSH Client Yes 23 tcp Telnet Client Yes 25 tcp SMTP Mail Server No 69 tcp TFTP TFTP Server No 161 tcp/udp SNMP XMS Server No 162 tcp/udp SNMP Traphost Note Up to four Traphosts may be configured. XMS Server Yes - but required by XMS 443 tcp HTTPS (WMI,WPR) Client Yes 514 udp Syslog Syslog Server No 1812, 1645 udp RADIUS (some servers use 1645) RADIUS Server Yes 1813, 1646 udp RADIUS Accounting (some servers still use 1646) RADIUS Accounting Server Yes 2055 udp Netflow Client Yes 5000 tcp Virtual Tunnel VTUN Server Yes Installing the Wi-Fi Array 87 Wi-Fi Array Port Application Peer Configurable XMS 25 tcp SMTP Mail Server Yes 161 udp SNMP Arrays No 162 udp SNMP Traphost 1 Arrays Via XMS config file HTTPS Arrays No 514 udp Resident Syslog server Internal* Via XMS config file 1099 tcp RMI Registry Internal* No 2000 tcp XMS Back-end Server Internal* No 3306 tcp MySQL Database Internal* No 8001 tcp Status Viewer Internal* No 8007 tcp Tomcat Shutdown Internal* During installation 8009 tcp Web Container Internal* During installation 9090 tcp XMS Webserver XMS client During installation 9091 tcp XMS Client Server XMS client Via XMS config file 443 tcp * Internal to XMS Server, no ports need to be unblocked on other network devices See Also Management Control External Radius Services VLAN Management 88 Installing the Wi-Fi Array Wi-Fi Array Network Management Planning Network management can be performed using any of the following methods: Command Line Interface, using an SSH (Secure Shell) utility, like PuTTY. The utility must be set up to use SSH-2, since the Array will only allow SSH-2 connections. Web-based management, using the Array’s embedded Web Management Interface (WMI). This method provides configuration and basic monitoring tools, and is good for small deployments (one or two units). Centralized Web-based management, using the optional Xirrus Management System (XMS), which can be run on a dedicated Xirrus appliance (XM-3300) or your own server. The XMS is used for managing large Wi-Fi Array deployments from a centralized Web-based interface and offers the following features: Globally manage large numbers of Arrays (up to 500) Seamless view of the entire wireless network Easily configure large numbers of Arrays Rogue AP monitoring Easily manage system-wide firmware updates Monitor performance and trends Aggregation of alerts and alarms See Also Failover Planning Power Planning Security Planning Installing the Wi-Fi Array 89 Wi-Fi Array WDS Planning WDS (Wireless Distribution System) creates wireless backhauls between arrays, allowing your wireless network to be expanded using multiple Arrays without the need for a wired backbone to link them (see Figure 32). WDS features include: One to three IAPs may be used to form a single WDS link, yielding up to 900 Mbps bandwidth per link (up to 162 Mbps for XS model Arrays). Up to three different WDS links may be created on a single Array. Automatic IAP Load Balancing If desired, you may allow clients to associate to a BSS on the same radio interface used for a WDS Host Link. This will take bandwidth from the WDS link. Figure 32. WDS Link 90 Multiple links per Array allow you to configure multi-hop connections. Installing the Wi-Fi Array Wi-Fi Array Figure 33. A Multiple Hop WDS Connection Multiple WDS links can provide link redundancy (failover capability - see Figure 34). A network protocol (Spanning Tree Protocol — STP) prevents Arrays from forming network loops. Figure 34. WDS Failover Protection Installing the Wi-Fi Array 91 Wi-Fi Array WDS links have a Host/Client relationship similar to the usual IAP/station pattern for Arrays: A WDS Client Link associates/authenticates to a host (target) Array in the same way that a station associates to an IAP. The client side of the link must be configured with the root MAC address of the target (host) Array. A WDS Host Link acts like an IAP by allowing one WDS Client Link to associate to it. An Array may have both client and host links. WDS configuration is performed only on the client-side Array. See “WDS” on page 305. Note that both Arrays must be configured with the same SSID name. 92 Installing the Wi-Fi Array Wi-Fi Array Common Deployment Options The following table lists some typical and recommended deployment options for a number of the features that have been discussed in this chapter. Number of Wi-Fi Arrays Function One or Two Three or More AC (some Array models) AC (some Array models) Power over Gigabit Ethernet Power over Gigabit Ethernet UPS backup (recommended) Failover Recommended Highly recommended VLANs Optional Optional use, Power Can be used to put all APs on one VLAN or map to existing VLAN scheme Encryption Authentication WPA2 with AES (recommended) WPA2 with AES (recommended) PSK or 802.1x 802.1x keying Internal RADIUS server EAP-PEAP External RADIUS server Pre-Shared Key Management Internal WMI XMS (SNMP) Internal CLI (via SSHv2) See Also Coverage and Capacity Planning Deployment Examples Network Management Planning Planning Your Installation Power Planning Security Planning Installing the Wi-Fi Array 93 Wi-Fi Array Installation Workflow This workflow illustrates the steps that are required to install and configure your Wi-Fi Array successfully. Review this flowchart before attempting to install the unit on a customer’s network. Determine the number of Arrays needed Choose the location(s) for your Wi-Fi Arrays Run Ethernet cables for PoGE (<100m total distance from switch) Install the mounting plate Connect the cables and turn on the power Verify that the Ethernet link and radio LEDs are functioning correctly Log in to WMI and enter your license Perform the Express Setup procedure Figure 35. Installation Workflow See Also Coverage and Capacity Planning Deployment Examples 94 Installing the Wi-Fi Array Wi-Fi Array Common Deployment Options Failover Planning Installation Prerequisites Planning Your Installation Power Planning Wi-Fi Array Product Overview Product Specifications — XN16, XN12, and XN8 Product Specifications — XS16 and XS8 Product Specifications — XS4 Security Planning Installing the Wi-Fi Array 95 Wi-Fi Array Installing Your Wi-Fi Array This section provides instructions for completing a physical installation of your Xirrus Wi-Fi Array. Choosing a Location Based on coverage, capacity and deployment examples previously discussed, choose a location for the Array that will provide the best results for your needs. The Wi-Fi Array was designed to be mounted on a ceiling where the unit is unobtrusive and wireless transmissions can travel unimpeded throughout open plan areas. You also have the option of mounting the Array on a wall, using the optional wall mount assembly kit. Choose a location that is central to your users (see the following diagram for correct placement. WRONG RON RO ON WRONG RON RO O G ON CORRECT ORRE ORREC Figure 36. Array Placement 96 Installing the Wi-Fi Array Wi-Fi Array Wiring Considerations If you are using the Xirrus Power over Gigabit Ethernet modules (PoGE) to distribute power, see “Power over Gigabit Ethernet (PoGE)” on page 14. If you prefer to use AC power and you have an Array that supports AC, an AC power outlet must be available to the Array. Once you have determined the best location for your Wi-Fi Array, you must run cables to the location for the following services: Power One of the following options: No power cable to the Array is required if using PoGE modules. The PoGE module requires a dedicated AC power outlet (100 240 VAC). Dedicated AC power if PoGE is not in use. A UL-approved cord is shipped with all AC-equipped Arrays. You must use a ULapproved cord if using AC power. Network Gigabit 1 — If using PoGE modules, the total of all Cat 5e or Cat 6 cable segments from the Gigabit Ethernet switch to the Array must be less than 100m long. The Array must be connected to PoGE networks without routing cabling to the outside plant, to ensure that cabling is not exposed to lightning strikes or possible high voltage crossover. Gigabit 2 (optional, not available on the four-port Arrays) Fast Ethernet (optional, not available on the four-port Arrays) Serial cable (optional) — cable lengths up to 25’ per the RS-232 specification. Installing the Wi-Fi Array 97 Wi-Fi Array Important Notes About Network Connections Read the following notes before making any network connections. When the unit’s IP address is unknown or a network connection has not been established, the serial cable is used for connecting directly with the Command Line Interface (CLI) via HyperTerminal. When a network connection is established, the Array can be managed from any of the available network connections, either Fast Ethernet, Gigabit 1 or Gigabit 2. The Array’s Ethernet ports should be plugged into an Ethernet switch, not an Ethernet hub — if a hub is used, we recommend that you connect only one Ethernet port. The Gigabit1 Ethernet interface is the primary port for both data and management traffic. If a single Ethernet connection is used, it must be connected to the Gigabit1 Ethernet interface. See also, “Port Failover Protection” on page 80. The 10/100 Ethernet Port may be used for managing the Array out of band from the Gigabit Ethernet ports. The 10/100 port will route only management traffic, using a static route that may be configured for this interface. See “interface” on page 370. See Also Failover Planning Installation Prerequisites Installation Workflow Mounting the Array Power over Gigabit Ethernet (PoGE) 98 Installing the Wi-Fi Array Wi-Fi Array Mounting the Array A number of options are available for mounting Arrays: Ceiling mount Wall mount Secure mount in a locking indoor enclosure Outdoor enclosure I-Beam mount in a protective enclosure (gymnasium mount) Factory enclosure A detailed Quick Installation Guide is provided with the mounting option that you selected when ordering your Array. Please follow the provided instructions carefully. Dismounting the Array To dismount any other Array model For all Array models other than the XS-3700/3900, push up on the Array (i.e., push it against the mounting plate). Then turn the Array to the left to remove it. This is similar to dismounting a smoke detector. Installing the Wi-Fi Array 99 Wi-Fi Array Powering Up the Wi-Fi Array When powering up, the Array follows a specific sequence of LED patterns showing the boot progress, and following a successful boot will provide extensive status information. Ethernet Activity LEDs Status LED IAP LEDs (x16) Figure 37. LED Locations (XN16) Array LED settings may be altered or disabled entirely for diagnostic purposes or for personal preference. Changes are made via the Array’s Command Line Interface or the Web Management Interface — refer to “LED Settings” on page 303. 100 Installing the Wi-Fi Array Wi-Fi Array Array LED Operating Sequences Use the following tables to review the operating sequences of the Array’s LEDs. “LED Boot Sequence” on page 101 “LED Operation when Array is Running” on page 102 LED Boot Sequence The normal boot LED sequence is as follows: Array Activity Status LED IAP LEDs Power ON Blinking GREEN All OFF Boot loader power ON self-test Blinking GREEN All ON Image load from compact FLASH Blinking GREEN Spinning pattern (rotate all to ON, then all to OFF) Image load failure Blinking ORANGE All OFF Hand off to ArrayOS Solid GREEN All OFF System software initialization Solid GREEN Walking pattern — (LED rotating one position per second) Up and running Solid GREEN ON for IAPs that are up: OFF for IAPs that are down. Behavior may be changed using “LED Settings” on page 303. Installing the Wi-Fi Array 101 Wi-Fi Array LED Operation when Array is Running The normal LED operation when the Array is running is shown in the table below. Note that behavior may be modified using “LED Settings” on page 303 or via the CLI. LED Status Reason IAP LED is OFF IAP is down IAP LED is solid ON IAP is up, but no associations and no traffic IAP LED heartbeat IAP is up, with stations associated but no traffic IAP LED flashing IAP is up, passing traffic Flashing at 10 Hz Flashing at 5 Hz Flashing at 2.5 Hz Traffic > 1500 packets/sec Traffic > 150 packets/sec Traffic > 1 packet/sec IAP LED is GREEN IAP is operating in the 2.4 GHz band IAP LED is ORANGE IAP is operating in the 5 GHz band IAP LED flashing ORANGE to GREEN at 1 Hz IAP abg(n)2 is in monitor mode (standard intrude detect) Ethernet LEDs are dual color Ethernet LED is ORANGE Transferring data at 1 Gbps Ethernet LED is GREEN Transferring data at 10/100 Mbps See Also Installation Prerequisites Installation Workflow Installing Your Wi-Fi Array LED Settings 102 Installing the Wi-Fi Array Wi-Fi Array Establishing Communication with the Array The Array can be configured through the Command Line Interface (CLI) or the graphical Web Management Interface (WMI). You can use the CLI via the serial management port, the Fast Ethernet port, or either of the Gigabit Ethernet ports. You can use the WMI via any of the Array’s Ethernet ports. Serial Fast Ethernet Gigabit 1 Gigabit 2 Figure 38. Network Interface Ports Using the Serial Port If using the serial port to make your connection, use serial settings of 8 bits, no parity, no flow control, 1 stop bit (8N1) and a speed setting of 115200 baud. Use the communication package of your choice. Using the Ethernet Ports By default, the Array's Ethernet interfaces use DHCP to obtain an IP address. If the Array is booted and does not receive DHCP addresses on either the Fast Ethernet or Gigabit Ethernet ports, the Fast Ethernet port will default to an IP address of 10.0.1.1 and both Gigabit Ethernet ports will default to 10.0.2.1. If the Array is connected to a network that provides DHCP addresses, the IP address can be determined by the following two methods: 1. Examine the DHCP tables on the server and find the addresses assigned to the Array (Xirrus MAC addresses begin with 000F7D). 2. Query the Array using the CLI via the serial port. Use the show ethernet command to view the IP addresses assigned to each port. Installing the Wi-Fi Array 103 Wi-Fi Array Logging In When logging in to the Array, use the default user name and password — the default user name is admin, and the default password is admin. See Also Installation Workflow Performing the Express Setup Procedure Powering Up the Wi-Fi Array Entering the License A license is needed to operate the Wi-Fi Array at full functionality. Without a license, the Array may only be powered up and have a basic network configuration. The Array’s license determines many of the features that are available on the Array. For example, automatic cell sizing and channel allocation require a license supporting the RF Performance Manager (RPM). Also, IEEE 802.11n operation on XR and XN model Arrays requires a license. The Array’s license is not installed at the factory. You must enter your license before proceeding to the next step, Performing the Express Setup Procedure. The procedure below describes entering the license key using the WMI. If you are using the Xirrus Management System (XMS), you may use it to easily manage and upgrade large numbers of licenses for the wireless network. 104 1. This procedure assumes that you have pointed a browser to the Array’s IP address to start WMI, and that you have logged in with the default username and password above. 2. In the left had frame, in the Tools section, click System Tools. 3. License Key: Enter the key that was provided for the Array. The key was provided to you in an email as an attachment in the form of an Excel file (.xls). Enter the key exactly as it appears in the file. Click the Upgrade button to apply the key. Installing the Wi-Fi Array Wi-Fi Array 4. Now you may verify the features provided by the key. In the Status section of the left hand frame, click Array and then click Information. Check the items listed in the License Features row. If you are installing a large number of licenses and do not have XMS, a Xirrus Licensing Tool may be acquired from Xirrus Support to help push licenses to large number of Arrays. Installing the Wi-Fi Array 105 Wi-Fi Array Performing the Express Setup Procedure The Express Setup procedure establishes global configuration settings that enable basic Array functionality. Changes made in this window will affect all radios. Figure 39. Express Setup 106 Installing the Wi-Fi Array Wi-Fi Array Procedure for Performing an Express Setup 1. Host Name: Specify a unique host name for this Array. The host name is used to identify the Array on the network. Use a name that will be meaningful within your network environment, up to 64 alphanumeric characters. The default is Xirrus-WiFi-Array. 2. Location Information: Enter a brief but meaningful description that accurately defines the physical location of the Array. In an environment where multiple units are installed, clear definitions for their locations are important if you want to identify a specific unit. 3. Admin Contact: Enter the name and contact information of the person who is responsible for administering the Array at the designated location. 4. Admin Email: Enter the email address of the admin contact you entered in Step 3. 5. Admin Phone: Enter the telephone number of the admin contact you entered in Step 3. 6. Configure SNMPv2: Select whether to Enable SNMPv2 on the Array, and change the SNMP Community Strings if desired. If you are using the Xirrus Management System (XMS), these strings must match the values used by XMS. The default values for the Array match the defaults in XMS. For more details, including SNMPv3, see “SNMP” on page 199. 7. Configure the Fast Ethernet (10/100 Megabit), Gigabit 1 and Gigabit 2 network interfaces. The fields for each of these interfaces are the same, and include: a. Enable Interface: Choose Yes to enable this network interface, or choose No to disable the interface. b. Allow Management on Interface: Choose Yes to allow management of the Array via this network interface, or choose No to deny all management privileges for this interface. c. Configuration Server Protocol: Choose DHCP to instruct the Array to use DHCP to assign IP addresses to the Array’s Ethernet interfaces, Installing the Wi-Fi Array 107 Wi-Fi Array or choose Static if you intend to enter IP addresses manually. If you choose the Static IP option, you must enter the following information: 8. IP Address: Enter a valid IP address for this Array. To use any of the remote connections (Web, SNMP, or SSH), a valid IP address must be used. IP Subnet Mask: Enter a valid IP address for the subnet mask (the default is 255.255.255.0). The subnet mask defines the number of IP addresses that are available on the routed subnet where the Array is located. Default Gateway: Enter a valid IP address for the default gateway. This is the IP address of the router that the Array uses to forward data to other networks. SSID Settings: This section specifies the wireless network name and security settings. a. SSID (Wireless Network Name): The SSID (Service Set Identifier) is a unique name that identifies a wireless network. All devices attempting to connect to a specific WLAN must use the same SSID. The default for this field is “xirrus.” For additional information about SSIDs, go to the Multiple SSIDs section of “Frequently Asked Questions” on page 432. b. Wireless Security: Select the desired wireless security scheme (Open, WEP, WPA, WPA2, or WPA-Both). WPA2 is recommended for the best Wi-Fi security. 108 • Open — This option offers no data encryption and is not recommended, though you might choose this option if clients are required to use a VPN connection through a secure SSH utility, like PuTTy. • WEP (Wired Equivalent Privacy) — An optional IEEE 802.11 function that offers frame transmission privacy similar to a wired network. WEP generates secret shared encryption keys that both source and destination stations can use to alter frame bits to avoid disclosure to eavesdroppers. Installing the Wi-Fi Array Wi-Fi Array • WPA (Wi-Fi Protected Access) — A Wi-Fi Alliance standard that contains a subset of the IEEE 802.11i standard, using TKIP or AES as an encryption method and 802.1x for authentication. • WPA2 (Wi-Fi Protected Access 2) — WPA2 is the follow-on security method to WPA for wireless networks and provides stronger data protection and network access control. It offers Enterprise and consumer Wi-Fi users with a high level of assurance that only authorized users can access their wireless networks. Like WPA, WPA2 is designed to secure all versions of 802.11 devices, including 802.11a, 802.11b, 802.11g, and 802.11n, multi-band and multi-mode. • WPA-Both (WPA and WPA2) — This option makes use of both WPA and WPA2. For more information about security, including a full review of all security options and settings, go to “Understanding Security” on page 210. c. Wireless Key/Passphrase: Depending on the wireless security scheme you selected, enter a unique WEP key or WPA passphrase. d. Confirm Key/Passphrase: If you entered a WEP key or WPA passphrase, confirm it here. 9. Admin Settings: This section allows you to change the default password for the Array. Note that the Array also offers the option of authenticating administrators using a RADIUS server (see “Admin Management” on page 215). a. New Admin Password: If desired, enter a new administration password for managing this Array. Choose a password that is not obvious, and one that you can remember. If you forget your password, you must reset the Array to its factory defaults so that the password is reset to admin (its default setting). b. Confirm Admin Password: If you entered a new administration password, confirm the new password here. Installing the Wi-Fi Array 109 Wi-Fi Array 10. Time and Date Settings: This section specifies an optional time (NTP Network Time Protocol) server or modifies the system time if you’re not using a server. a. Time Zone: Select your time zone from the choices available in the pull-down list. b. Use Network Time Protocol: Check this box if you want to use an NTP server to synchronize the Array’s clock. This ensures that Syslog time-stamping is maintained across all units. Without an NTP server assigned (no universal clock), each Array will use its own internal clock and stamp times accordingly, which may result in discrepancies. If you check Yes, the NTP server fields are displayed. If you don’t want to use an NTP server, leave this box unchecked (default) and set the system time on the Array manually. c. NTP Primary Server: If you are using NTP, enter the IP address or domain name of the NTP server. d. NTP Secondary Server: Enter the IP address or domain name of an optional secondary NTP server to be used in case the Array is unable to contact the primary server. 110 e. Set Time (hrs:min:sec): If you are not using NTP, check this box if you want to adjust the current system time. When the box is checked, the time fields become active. Enter the revised time (hours, minutes, seconds, am/pm) in the corresponding fields. If you don’t want to adjust the current time, this box should be left unchecked (default). f. Set Date (month/day/year): If you are not using NTP, check this box if you want to adjust the current system date. When the box is checked, the date fields become active. Enter the revised date (month, day and year) in the corresponding fields. If you don’t want to adjust the current date, this box should be left unchecked (default). g. Auto Adjust Daylight Savings: If you are not using NTP, check this box if you want the system to adjust for daylight savings automatically, otherwise leave this box unchecked (default). Installing the Wi-Fi Array Wi-Fi Array 11. IAP Settings: Enable/Configure All IAPs: Click on the Execute button to enable and auto configure all IAPs (a message displays the countdown time — in seconds — to complete the auto-configuration task). When an IAP is enabled, its LED is switched on. (Figure 40, see also “Array LED Operating Sequences” on page 101.) LED on Figure 40. LEDs are Switched On 12. Click on the Apply button to apply the new settings to this session 13. Click on the Save button to save your changes (otherwise your new settings will not take effect). This ends the Express Setup procedure. See Also Establishing Communication with the Array Installation Prerequisites Installation Workflow Logging In Multiple SSIDs Security Installing the Wi-Fi Array 111 Wi-Fi Array 112 Installing the Wi-Fi Array Wi-Fi Array The Web Management Interface This topic provides an overview of the Xirrus Wi-Fi Array’s embedded Web Management Interface (WMI), used for establishing your network’s configuration settings and wireless operating parameters. It also includes login instructions. The following topics are discussed: An Overview Structure of the WMI User Interface Logging In Applying Configuration Changes The Web Management Interface 113 Wi-Fi Array An Overview The WMI is an easy-to-use graphical interface to your Wi-Fi Array. It allows you to configure the product to suit your individual requirements and ensure that the unit functions efficiently and effectively. Figure 41. Web Management Interface 114 The Web Management Interface Wi-Fi Array Structure of the WMI The content of the WMI is organized by function and hierarchy, shown in the following table. Click on any item below to jump to the referenced destination. Status Windows Array Status Windows Array Summary Array Information Array Configuration Admin History Network Status Windows Network Map Spanning Tree Status Routing Table ARP Table DHCP Leases Connection Tracking/NAT CDP Neighbors Network Assurance RF Monitor Windows IAPs Spectrum Analyzer Intrusion Detection Station Status Windows Stations Location Map RSSI Signal-to-Noise Ratio (SNR) Noise Floor Max by IAP The Web Management Interface Statistics Windows IAP Statistics Summary Per-IAP Statistics Network Statistics VLAN Statistics WDS Statistics Filter Statistics Station Statistics Per-Station Statistics System Log Window 115 Wi-Fi Array Configuration Windows Express Setup Network Network Interfaces DNS Settings CDP Settings Services Time Settings (NTP) NetFlow Wi-Fi Tag System Log SNMP DHCP Server VLANs VLAN Management Security Admin Management Admin Privileges Admin RADIUS Management Control Access Control List Global Settings External Radius Internal Radius Rogue Control List SSIDs SSID Management Active IAPs Groups Group Management 116 Configuration Windows (cont’d) IAPs IAP Settings Global Settings (IAP) Global Settings .11a Global Settings .11bg Global Settings .11n Advanced RF Settings LED Settings WDS WDS Client Links Filters Filter Lists Filter Management Clusters Cluster Definition Cluster Management Cluster Operation Tool Windows System Tools CLI Options Logout The Web Management Interface Wi-Fi Array User Interface The WMI has been designed with simplicity in mind, making navigation quick and easy. In the following example, you’ll see that windows are divided into left and right frames. Left frame Right frame Array info Pull-down menu Help Log Message counters Click to configure/view statistics Figure 42. WMI: Frames The Web Management Interface 117 Wi-Fi Array The left frame contains three main elements: Configuration menu organized by function (for example, radio interfaces, security, etc.). Click the heading to display a summary of its current configuration, as well as an associated pull-down menu. Three Log Messages counters are located at the bottom of the menu. They provide a running total of messages generated by the ArrayOS Syslog subsystem during your session — organized into Critical, Warning, and General messages. Click on a counter to display the associated Syslog messages. Messages at the selected level or higher will be shown. For more information, please see “System Log Window” on page 168. The Array representation contains shortcut links. Click a radio to view statistics for it. Click the center of the Array to display the IAP Settings window, which allows you to configure the Array’s radios. The right frame displays the status information or configuration parameters for the Wi-Fi Array. This is where you review the Array’s current status and activity or input data (if you want to make changes). The green Array information bar at the top of the frame describes the Array — the Name and IP address allow you to quickly confirm that WMI is connected to the correct Array. The current Uptime since the last reboot is also shown. Some settings are only available if the Array’s license includes appropriate Xirrus Advanced Feature Sets. If a setting is unavailable (grayed out), then your license does not support the feature. See “About Licensing and Upgrades” on page 325. Note that WMI provides options which allow you to change its appearance and behavior. You may change: Style — changes the colors and appearance of WMI (i.e., its “skin”). Refresh Interval — the refresh time when automatic refresh is selected. Close menu section when deselected — changes the behavior of the menu in the left frame. Clear screen when loading new page. See “Options” on page 337 for more information. 118 The Web Management Interface Wi-Fi Array Utility Buttons At the bottom of each window you will find a set of useful buttons — a Feedback button, a Print button and a Help button. Print button Feedback button Help button Figure 43. WMI: Utility Buttons Click on the Feedback button to generate a Web page that allows you to submit your comments to Xirrus, Inc. You can also access the feedback page at http://www.xirrus.com/public/feedback/. Refer to Figure 44 on page 120 to see a sample of the feedback form. Click on the Print button to send a print file of the active window to your local printer. Click on the Help button to access the Array’s online help system. Submitting Your Comments When submitting comments via the Feedback button (Figure 44 , ensure that you provide as much detail as possible, including your contact information, the product model number that the comment relates to, and the ArrayOS software version (if known). When finished, click on the Submit button to submit your comment. The Web Management Interface 119 Wi-Fi Array Figure 44. Feedback Form 120 The Web Management Interface Wi-Fi Array Logging In Use this procedure to log in to the WMI via your Web browser. 1. Establish a network connection and open your Web browser. 2. Connect to the Wi-Fi Array via its default IP address (10.0.2.1 for both Gigabit 1 and Gigabit 2 Ethernet ports) or via a DHCP assigned IP address. 3. To log in to the Array’s Web Management Interface, enter admin when prompted for a user name and password. Figure 45. Logging In to the Wi-Fi Array Applying Configuration Changes When you have defined all your settings in any WMI configuration window, you must click on the Apply button for the changes to take effect in the current session, or click on the Save button to apply changes to this session and write your changes, so they will be preserved after a reboot. Character Restrictions When inputting strings in the WMI (for example, assigning SSIDs, host name, password, etc.), use common alphanumeric characters. Some of the fields in the WMI will not accept special characters, so use of the following characters should typically be avoided: The Web Management Interface “ 121 Wi-Fi Array 122 The Web Management Interface Wi-Fi Array Viewing Status on the Wi-Fi Array These windows provide status information and statistics for your Array using the product’s embedded Web Management Interface (WMI). You cannot make configuration changes to your Array from these windows. The following topics have been organized into functional areas that reflect the flow and content of the Status section of the navigation tree in the left frame of the WMI. “Array Status Windows” on page 123 “Network Status Windows” on page 129 “RF Monitor Windows” on page 139 “Station Status Windows” on page 147 “Statistics Windows” on page 160 “System Log Window” on page 168 Configuration and Tools windows are not discussed here. For information on these windows, please see: “Configuring the Wi-Fi Array” on page 171 “Using Tools on the Wi-Fi Array” on page 323 Array Status Windows The following Array Status windows are available: Array Summary — displays information on the configuration of all Array interfaces, including IAPs. Array Information — provides version/serial number information for all Array components. Array Configuration — shows all configuration information for the Array in text format. Admin History — shows all current and past logins since the last reboot. Viewing Status on the Wi-Fi Array 123 Wi-Fi Array Array Summary This is a status only window that provides a snapshot of the global configuration settings for all Wi-Fi Array network interfaces and IAPs. You must go to the appropriate configuration window to make changes to any of the settings displayed here — configuration changes cannot be made from this window. Clicking on an interface or IAP will take you to the proper window for making configuration changes. Figure 46. Array Summary Content of the Array Summary Window The Array Summary window is sub-divided into the Ethernet Interfaces section and the Integrated Access Points (radio) section, providing you with the following information: 124 Ethernet Interfaces Section This section provides information about network interface devices. To make configuration changes to these devices, go to “Network Interfaces” on page 180. • Interface: Lists the network interfaces that are available on the Array (10/100 Ethernet 0, Gigabit Ethernet 1 and Gigabit Ethernet 2). • Status: Shows the current state of each interface, either enabled or disabled. Viewing Status on the Wi-Fi Array Wi-Fi Array • Link: Shows whether the link on this interface is up or down. • DHCP: Shows whether DHCP on this port is enabled or disabled. • IP Address: Shows the current IP address assigned to each network interface device. • Subnet Mask: Shows the subnet mask, which defines the number of IP addresses that are available on the routed subnet where the Array is located. • Gateway: Shows the IP address of the router that the Array uses to transmit data to other networks. Integrated Access Points Section This section provides information about the Integrated Access Points (IAPs) that are contained within the Array. How many IAPs are listed depends on which product model you are using (16 IAPs for the XN16 or XS16; 12 IAPs for the XN12; 8 IAPs for the XR 48xx or XN8 or XS8; and 4 IAPs for the XR 44xx or XN4 or XS4). To make configuration changes to these IAPs, go to “IAP Settings” on page 271. • IAP: Lists the IAPs that are available on the Array. • State: Shows the current state of each IAP, either up or down. IAPs that are down are shown in RED. Figure 47 shows an example where IAP a3 is down. Figure 47. Disabled IAP (Partial View) • Channel: Shows which channel each IAP is using, and the channel setting. To avoid co-channel interference, adjacent radios should not Viewing Status on the Wi-Fi Array 125 Wi-Fi Array be using adjacent channels. To make channel selections for a specific IAP, go to “IAP Settings” on page 271. • Antenna: Shows which antenna is being used by each IAP. • Cell Size: Indicates which cell size setting is currently active for each IAP — small, medium, large, max, automatic, or manually defined by you. The cell size of an IAP is a function of its transmit power and determines the IAP’s overall coverage. To define cell sizes, go to “IAP Settings” on page 271. For additional information about cell sizes and the importance of planning for and defining the optimum cell sizes for your Array, go to “Coverage and Capacity Planning” on page 62. Figure 48. IAP Cells 126 • Tx Power: Shows the transmit power for each IAP. • Rx Threshold: Shows the receive threshold for each IAP. • Stations: Informs you how many client stations are currently associated with each IAP. XR and XN Arrays can handle up to 96 concurrent users per individual IAP, thus 16-port XN models can handle 1536 users per Array. • WDS Link: The WDS Link on this radio (if any). See “WDS” on page 305. • MAC Address/BSSID: Shows the MAC address for each IAP. • Description: The description (if any) that you set for this IAP. Viewing Status on the Wi-Fi Array Wi-Fi Array Array Information This is a status only window that shows you the current firmware versions utilized by the Array, serial numbers assigned to each module, MAC addresses, licensing information, recent boot timestamps, and current internal temperatures. Note that the License Features row lists the features that are supported by your Array’s license. See “About Licensing and Upgrades” on page 325 and “Advanced Feature Sets” on page 20 for more information. Figure 49. Array Information Viewing Status on the Wi-Fi Array 127 Wi-Fi Array You cannot make configuration changes in this window, but if you are experiencing issues with network services, you may want to print the content of this window for your records. Array Configuration This is a status only window that allows you to display the configuration settings assigned to the Array, based on the following filter options: Running — displays the current configuration (the one running now). Saved — displays the saved configuration from this session. Lastboot — displays the configuration as it was after the last reboot. Factory — displays the configuration established at the factory. Figure 50. Show Configuration If you want to see just the differences between the Running, Saved, Lastboot, and Factory configurations, you can do this by choosing a configuration option from the Select Config pull-down menu then selecting an alternative configuration option from the Select Diff pull-down menu. 128 Viewing Status on the Wi-Fi Array Wi-Fi Array To also include the default configuration settings in the output, choose your configuration then click in the Include Defaults check box. If Include Defaults is disabled, then only the changes from the default configuration are shown. Admin History It is useful to know who else is currently logged in to an array while you're configuring it. It's also nice to see who has logged in since the array booted. This status-only window shows you all administrator logins to the Array that have occurred since the last reboot. To determine who is currently logged in, check which entries say active in the Logout Time column. Figure 51. Admin Login History Network Status Windows The following Network Status windows are available: Network — displays a summary of network interface settings. Network Map — displays information about this Array and neighboring Arrays that have been detected. Spanning Tree Status — displays the spanning tree status of network links on this Array. Routing Table — displays information about routing on this Array. Viewing Status on the Wi-Fi Array 129 Wi-Fi Array ARP Table — displays information about Address Resolution Protocol on this Array. DHCP Leases — displays information about IP addresses (leases) that the Array has allocated to client stations. Connection Tracking/NAT — lists connections that have been established for client stations. CDP Neighbors — lists neighboring network devices using Cisco Discovery Protocol. Network Assurance — shows results of connectivity tests for network servers. Network This window provides a snapshot of the configuration settings currently established for Array’s wired interfaces. Depending on the model, this may include the 10/100 Ethernet 0 interface and the Gigabit 1 and Gigabit 2 interfaces. DNS Settings are summarized as well. You can click on any item in the Interface column to go to the associated configuration window. Figure 52. Network Settings WMI windows that allow you to change or view configuration settings associated with the network interfaces include: 130 “Network Interfaces” on page 180 “DNS Settings” on page 187 “CDP Settings” on page 189 Viewing Status on the Wi-Fi Array Wi-Fi Array Network Map This window offers detailed information about this Array and all neighboring Arrays, including how the Arrays have been set up within your network. Figure 53. Network Map The Network Map has a number of options at the top of the page that allow you to customize your output by selecting from a variety of information that may be displayed. You may sort the rows based on any column that has an active column header, indicated when the mouse pointer changes to the hand icon . Click Refresh to update the information at any time. Click Auto Refresh to instruct the Array to refresh this window automatically. Content of the Network Map Window By default, the network map shows the following status information for each Array: Array Name: The host name assigned to the Array. To establish the host name, go to “Express Setup” on page 173. You may click the host name to access WMI for this Array. IP Address: The Array’s IP address. You may click the address to access WMI for this Array. If DHCP is enabled, the Array’s IP address is assigned by the DHCP server. If DHCP is disabled, you must assign a Viewing Status on the Wi-Fi Array 131 Wi-Fi Array static IP address. To enable DHCP or to assign a static IP address for the Array, go to “Express Setup” on page 173. Location: The location assigned to the Array. To establish the location information, go to “Express Setup” on page 173. Array OS: The software version running on the Array. IAP: The number of IAPs on the Array. (IAP) Up: Informs you how many IAPs are currently up and running. To enable or disable all IAPs, go to “Express Setup” on page 173. To enable or disable individual IAPs, go to “IAP Settings” on page 271. SSID: Informs you how many SSIDs have been assigned for the Array. To assign an SSID, go to “SSID Management” on page 248. (SSID) On: Informs you how many SSIDs are enabled. To enable or disable SSIDs, go to “SSID Management” on page 248. In Range: Informs you whether the Array is within wireless range of another Wi-Fi Array. Fast Roam: Informs you whether or not the Xirrus fast roaming feature is enabled. This feature utilizes the Xirrus Roaming Protocol (XRP) ensuring fast and seamless roaming capabilities between IAPs or Arrays at both Layer 2 and Layer 3. To enable or disable fast roaming, go to “Global Settings (IAP)” on page 277. Uptime (D:H:M): Informs you how long the Array has been up and running (in Days, Hours and Minutes). To see additional information, select from the following checkboxes at the bottom of the page. This will show the columns described below. Hardware Model: The model number of each Array (XN16, XS4, etc.), plus the amount of RAM memory and the speed of the processor. Serial: Displays the serial number of each Array. License 132 License Key: The license key of each Array. Viewing Status on the Wi-Fi Array Wi-Fi Array Licensed Features: Lists the optional features enabled by the key, if any. Software (enabled by default) Enable/disable display of the Array OS column. Firmware Boot Loader: The software version number of the boot loader on each Array. SCD Firmware: The software version number of the SCD firmware on each Array. IAP Info (enabled by default) Enable/disable display of the IAP/Up columns. Stations Stations: Tells you how many stations are currently associated to each Array. To deauthenticate a station, go to “Stations” on page 148. The columns to the right (H, D, W, and M) show the highest number of stations that have been associated over various periods of time: the previous hour, day, week, and month. Default Sets the columns displayed to the default settings. By default, only Software and IAP Info are selected. Spanning Tree Status Multiple active paths between stations can cause loops in the network. If a loop exists in the network topology, the potential exists for the duplication of messages. The spanning tree protocol is a link management protocol that provides path redundancy while preventing undesirable loops. For a wireless network to function properly, only one active path can exist between two stations. To facilitate path redundancy, the spanning tree protocol defines a tree that spans all stations in the network and forces certain redundant data paths into a standby (blocked) state. If one segment in the spanning tree becomes unreachable, the Viewing Status on the Wi-Fi Array 133 Wi-Fi Array spanning tree algorithm reconfigures the network topology and reestablishes the link by activating the standby path. The spanning tree function is transparent to client stations. Figure 54. Spanning Tree Status This window shows the spanning tree status (forwarding or blocked) for path segments that terminate on the gigabit ports and WDS links of this Array. You may sort the rows based on the VLAN Name or Number columns by clicking the column header. Click Refresh to update the information at any time. Click Auto Refresh to instruct the Array to refresh this window automatically. See Also Network Network Interfaces Network Status Windows VLANs WDS 134 Viewing Status on the Wi-Fi Array Wi-Fi Array Routing Table This status-only window lists the entries in the Array’s routing table. The table provides the Array with instructions for sending each packet to its next hop on its route across the network. Figure 55. Routing Table See Also VLANs Configuring VLANs on an Open SSID ARP Table This status-only window lists the entries in the Array’s ARP table. For a device with a given IP address, this table lists the device’s MAC address. It also shows the Array interface through which this device may be reached. The table typically includes devices that are on the same local area network segment as the Array. Figure 56. ARP Table See Also Routing Table ARP Filtering Viewing Status on the Wi-Fi Array 135 Wi-Fi Array DHCP Leases This status-only window lists the IP addresses (leases) that the Array has allocated to client stations. For each, it shows the IP address assigned from one of the defined DHCP pools, and the MAC address and host name of the client station. The start and end time of the lease show how long the allocation is valid. The same IP address is normally renewed at the expiration of the current lease. Figure 57. DHCP Leases See Also DHCP Server Connection Tracking/NAT This status-only window lists the session connections that have been created on behalf of clients. This table may also be used to view information about current NAT sessions. Figure 58. Connection Tracking Click the Show Netbios checkbox at the bottom of the page to display NetBIOS name information for the source and destination location of the connection. The Netbios columns will replace traffic statistics columns. 136 Viewing Status on the Wi-Fi Array Wi-Fi Array You may sort the rows based on any column that has an active column header, indicated when the mouse pointer changes to the hand icon . Click Refresh to update the information at any time. Click Auto Refresh to instruct the Array to refresh this window automatically. See Also Filters CDP Neighbors This status-only window lists devices on the Array’s network that support the Cisco Discovery Protocol (CDP). Figure 59. CDP Neighbors The Array performs discovery on the network on an ongoing basis. This list shows the devices that have been discovered — Cisco devices and other devices on the network that have CDP running. For each, it shows the device’s host name, IP address, manufacturer and model name, the device interface that is connected to the network (i.e., the port that was discovered), and the network capabilities of the device (switch, router, supported protocols, etc.). CDP must be enabled on the Array in order to gather and display this information. See “CDP Settings” on page 189. Viewing Status on the Wi-Fi Array 137 Wi-Fi Array Network Assurance This status-only window shows the results of ongoing network assurance testing. Figure 60. Network Assurance The Array checks connectivity to network servers that you have configured (for example, DNS and NTP servers) on an ongoing basis. For each server, this list shows the server’s host name (if any), IP address, and status. Network assurance must be enabled on the Array in order to perform these connectivity tests and display this information. See “Management Control” on page 222. See Also Management Control 138 Viewing Status on the Wi-Fi Array Wi-Fi Array RF Monitor Windows Every Wi-Fi Array includes an integrated RF spectrum analyzer as a standard feature. The spectrum analyzer allows you to characterize the RF environment by monitoring throughput, signal, noise, errors, and interference levels continually per channel. This capability uses the built-in threat-sensor radio abg(n)2. The associated software is part of the ArrayOS. The following RF Status windows are available: IAPs — displays current statistics and RF measurements for each of the Array’s IAPs. Spectrum Analyzer — displays current statistics and RF measurements for each of the Array’s channels. Intrusion Detection — displays rogue APs that have been detected by the Array. Some status information is only available if the Array’s license includes Advanced Feature Sets. For example, the Spectrum Analyzer requires the Xirrus Advanced RF Analysis Manager (RAM). If a feature is unavailable, then your license does not support the feature and you will get an error message if you try to set the feature. See “About Licensing and Upgrades” on page 325. Viewing Status on the Wi-Fi Array 139 Wi-Fi Array IAPs The RF Monitor — IAPs window displays traffic statistics and RF readings observed by each Array IAP (radio). Note that the data is an instantaneous snapshot for the IAP — it is not an average or a cumulative total. Figure 61. RF Monitor — IAPs Figure 61 presents the data as a graphical display, enabled by selecting the Graph checkbox on the lower left. If this option is not selected, data is presented as a numerical table. You may sort the rows based on any column that has an active column header, indicated when the mouse pointer changes to the hand icon . Click Refresh to update the information at any time. Click Auto Refresh to instruct the Array to refresh this window automatically. 140 Viewing Status on the Wi-Fi Array Wi-Fi Array Spectrum Analyzer The RF measurements for this feature are obtained by IAP abg(n)2, which must be set to monitor mode for any data to be available. See “IAP Settings” on page 271. Spectrum analysis on Wi-Fi Arrays is a distributed capability that automatically covers the entire Wi-Fi network, since a sensor is present in every unit. Arrays monitor the network 24/7 and analyze interference anywhere in the network from your desk. There’s no need to walk around with a device as with traditional spectrum analyzers, thus you don’t have to be in the right place to find outside sources that may cause network problems or pose a security threat. The Array monitors all 802.11 radio bands (a/b/g/n), not just those currently used for data transmission. The RF Spectrum Analyzer window displays instantaneous traffic statistics and RF readings for all channels, as measured by the Array’s abg(n)2 radio. This differs from the RF Monitor-IAPs window, which displays values measured by each IAP radio for its current assigned channel. For the spectrum analyzer, the abg(n)2 radio is in a listen-only mode, scanning across all Wi-Fi channels. Each channel is scanned in sequence, for a 250 millisecond interval per channel. The spectrum analyzer window presents the data as a graphical display of vertical bar graphs for each statistic as shown in Figure 62 (the default presentation), or horizontally as bar graphs or numerical RF measurements. The measurements displayed are explained in “Spectrum Analyzer Measurements” on page 143. As an aid to viewing data for a particular channel, click the channel number. The channel will be highlighted down the page (or across the page for a rotated view, in both text and graph modes). Click additional channels to highlight them for easy comparison. To remove the highlighting from a channel, click the channel number again. Click Refresh to update the information at any time. Click Auto Refresh to instruct the Array to refresh this window automatically. Viewing Status on the Wi-Fi Array 141 Wi-Fi Array Click Channel number to highlight Select Display Options Figure 62. RF Spectrum Analyzer The Spectrum Analyzer offers several display options: 142 Viewing Status on the Wi-Fi Array Wi-Fi Array To display horizontal bar graphs, click the Rotate checkbox at the bottom of the data window. In the rotated view, if you wish to view data as a numerical table, click the Text checkbox. Click again to return to a graphical display. The text option is only available in the rotated view. When viewing a graphical display, click Bars to have the bar graphs displayed against a gray background — you may find this easier on the eyes. This operation is not available when Text is selected. You may sort the rows based on any column that has an active column header, indicated when the mouse pointer changes to the hand icon Sorting is only available in the rotated view. At the bottom left of the frame, you may select whether to display only 2.4 GHz channels, 5 GHz channels, or both (the default is both). Note that the data is an instantaneous snapshot — it is not an average or a cumulative total. Spectrum Analyzer Measurements The spectrum analyzer displays the following information: Packets/Sec: Total number of Wi-Fi packets per second on the channel, both valid and errored packets. Bytes/Sec: Total number of Wi-Fi bytes per second on the channel, valid packets only. 802.11 Busy: Percentage of time that 802.11 activity is seen on the channel. Other Busy: Percentage of time that the channel is unavailable due to non-802.11 activity. The total busy time (802.11 Busy plus Other Busy) will never total more than 100%. The remaining time (100% minus total busy time) is quiet time — the time that no activity was seen on the channel. Signal to Noise: Average SNR (signal to noise ratio) seen on the channel, calculated from the signal seen on valid 802.11 packets less the noise floor level. A dash value “-“means no SNR data was available for the interval. Viewing Status on the Wi-Fi Array 143 Wi-Fi Array 144 Noise Floor: Average noise floor reading seen on the channel (ambient noise). A dash value “-“means no noise data was available for the interval. Error Rate: Percentage of the total number of Wi-Fi packets seen on the channel that have CRC errors. The Error rate percentage may be high on some channels since the monitor radio is set to receive at a very sensitive level, enabling it to hear packets from devices at far distances. Average RSSI: Average RSSI level seen on 802.11 packets received on the channel. A dash value “-“means no RSSI data was available for the interval. Average Data Rate: Average data rate over time (per byte, not per packet) seen on 802.11 packets received on the channel. A dash value “-“means no data rate information was available for the interval. A higher date rate (above 6 Mbps) typically indicates user data traffic on the channel. Otherwise, the data rate reflects control packets at the lower basic rates. Viewing Status on the Wi-Fi Array Wi-Fi Array Intrusion Detection This window displays all detected access points, according to the category you select from the drop-down list at the top — either Unknown, Known or Approved. This includes ad hoc access points (station-to-station connections). You can sort the results based on the following parameters by clicking the desired column header: SSID Security BSSID Type Manufacturer Discovered Channel Last Active RSSI Select the type of AP to display Figure 63. Intrusion Detection/Rogue AP List The Intrusion Detection window provides the easiest method for designating rogue APs as Known. Approved, or Unknown. Choose one or more APs using the checkbox in the Select column, then set whether they are Approved, Known, or Unknown using the buttons on the lower left. Viewing Status on the Wi-Fi Array 145 Wi-Fi Array You can refresh the list at any time by clicking on the Refresh button, or click in the Auto Refresh check box to instruct the Array to refresh the list automatically. See Also Network Map Rogue Control List SSIDs SSID Management 146 Viewing Status on the Wi-Fi Array Wi-Fi Array Station Status Windows The following Station Status windows are available: Stations — this list describes all stations associated to the Array. Location Map — displays a map showing the approximate locations of all stations associated to the array. RSSI — for each associated station, this displays the Received Signal Strength Indicator at each of the Array’s IAPs. Signal-to-Noise Ratio (SNR) — for each associated station, this displays the SNR at each of the Array’s IAPs. Noise Floor — for each associated station, this displays the ambient noise (silence) value at each of the Array’s IAPs. Max by IAP — for each IAP, this shows the historical maximum number of stations that have been associated to it over various periods of time. Some status information is only available if the Array’s license includes the Xirrus Advanced RF Analysis Manager (RAM). If a feature is unavailable, then your license does not support the feature and you will get an error message if you try to set the feature. See “About Licensing and Upgrades” on page 325. Viewing Status on the Wi-Fi Array 147 Wi-Fi Array Stations This status-only window shows client stations currently visible to the Array. You may choose to view only stations that have associated to the Array, or only stations that are not associated, or both, by selecting the appropriate checkboxes above the list. The list shows the MAC address of each station, its NetBIOS name, its IP address, its manufacturer, the SSID used for the association, the Group (if any) that this station belongs to, the user name, its VLAN, its QoS, the IAP used for the association, transmit and receive rates, the RSSI for each station, and how long each association has been active (up time). You may click the Detail checkbox at the bottom of the window to show a number of additional columns, including security settings used by the connection, the channel and band used, and additional RF measurements. Figure 64. Stations You may sort the rows based on any column that has an active column header, indicated when the mouse pointer changes to the hand icon . Click again to reverse the sort order. You may select a specific station and perform one of the following actions by clicking the associated button: Deny Access: Sends a de-authentication frame to the selected station and explicitly denies it access by adding its MAC address to the Deny List in the Access Control List window. To permit access again, go to “Access Control List” on page 229 and delete the station from the Deny list. Deauthenticate: Sends a de-authentication frame to the selected station. The station may re-authenticate. Click on the Refresh button to refresh the station list, or click in the Auto Refresh check box to instruct the Array to refresh this window automatically. See Also Access Control List Station Status Windows 148 Viewing Status on the Wi-Fi Array Wi-Fi Array Location Map The Location Map shows the approximate locations of stations relative to this Array. The location of each station is computed based on the RSSI of its signal as received by the Array. The distance is adjusted based on the environment setting that you selected. You may display just the stations associated to this Array, unassociated stations (shown in gray), or both. The station count is shown on the right, above the map. You may also choose to display only 5 GHz stations (shown in orange) or 2.4 GHz stations (shown in green), or both. Array Hover mouse to show details Associated Stations orange - 5 GHz green - 2.4GHz Unassociated Station Figure 65. Location Map The map and Array are shown as if you were looking down on the Array from above, say from a skylight on the roof. Thus the positions of the radios abg(n)1 to abg(n)4 are a mirror image of the way they are typically drawn when looking at the face of the Array. Radios abg(n)1 to abg(n)4 are marked (1 to 4) on the map to show the orientation of the Array. A station is identified by the type of Preferred Label that you select: Netbios Name, IP Address, MAC Address, or Manufacturer. If multiple stations are near each other, they will be displayed slightly offset so that one station does not completely obscure another. You may minimize a station that is not of interest by clicking it. There is also a Minimize All button. Viewing Status on the Wi-Fi Array 149 Wi-Fi Array You may replace the range-finder background image above with your own custom image of the floorplan of the area served by the Array — see “Working with the Custom Image” on page 153 Hover the mouse over a station to show detailed information. (Figure 65) For a station that is associated to this Array, the details include: The IAP, Channel, and SSID to which the station is associated. The MAC and IP address and Netbios name of the station. The TX Rate and RX Rate of this connection. The approximate Distance of this station from the Array. The distance is estimated using the received signal strength and your environment setting. The environment determines the typical signal attenuation due to walls and other construction that affect signal reception. Controls and items displayed on the Location Map window The Location Map has its own scroll bars in addition to the browser’s scroll bars. If you narrow the browser window, the map’s scroll bar may be hidden. Use the browser’s bottom scroll bar if you need to move it into view. Scale Minimize stations Stations to display Replace background Preferred Label Zoom in Zoom out Reset display Rotate map Environment Setting Station counts Figure 66. Controls for Location Map 150 Display Associated/Unassociated: Select whether to display stations that are associated to the Array, stations that are not associated, or both. Viewing Status on the Wi-Fi Array Wi-Fi Array Display 2.4 GHz/5 GHz: Select whether to display 802.11bg(n) stations, or 802.11a(n) stations, or both. Minimize All: All stations are shown by default with their NetBIOS name or IP or MAC address. If the map is too cluttered, you can reduce the display for each station to a small rectangle. (Figure 67) You may still display detailed information for the station by hovering over it. To enlarge all rectangles, clear the Minimize All checkbox. Preferred Label: This field is located on the top of the window towards the right. It selects the type of label to be displayed for stations: Netbios Name, IP Address, MAC Address, or Manufacturer. If you select NetBIOS (this is the default), then that name, if known, will be used to label each Array. Else, its IP or MAC address will be used, in that order. Auto Refresh: Instructs the Array to refresh this window automatically. Refresh: Updates the stations displayed. Normal station display Minimized station display Figure 67. Minimizing stations Custom Image: Use this feature to replace the default background image with your own image of the floor plan of your location. Click the Browse button and browse to the desired file on your computer. This may be a .gif, .jpg, .jpeg., .png, .htm, or .html file. ??OK?? The scale of the file should be 100 feet per inch. Then click Upload (see below). For more Viewing Status on the Wi-Fi Array 151 Wi-Fi Array information on using the custom, image, see “Working with the Custom Image” on page 153. Upload: After browsing to the desired custom image, click the Upload button to install it. The map is redisplayed with your new background. No hash marks (for the map scale) are added to the image display. Reset: Click this button to restore the map display to the factory settings. All attributes are restored — including the stations selected for display, the scale, the rotation, and the background map. Rotate: Click this button to rotate the orientation of the entire map. It rotates the map 45o counter-clockwise. Enlarge: Click this button to enlarge (zoom in on) the map. The displayed Scale is updated with the new scale for the map. Reduce: Click this button to reduce (zoom out on) the map. The displayed Scale is updated with the new scale for the map. Environment: This field is located on the top right of the window. Select the type of environment for this Array’s deployment: Outdoor, Indoor open (few walls or obstructions), Indoor walled (typical wall or cubicle construction), or Indoor dense (many walls or obstructions, or unusually dense walls). Scale: This view-only value shows the approximate distance represented by each hashmark on the default map background. Associated, Unassociated, Total Stations: These view-only values show the station counts observed by the Array. See Also Station Status Windows 152 Viewing Status on the Wi-Fi Array Wi-Fi Array Working with the Custom Image After you have uploaded a custom image (see Custom Image and Upload in “Controls and items displayed on the Location Map window” on page 150), you should move the display of the Array on your map to correspond with its actual location at your site. To move the Array on the map, simply click it, then drag and drop it to the desired location. The Array will continue to follow the mouse pointer to allow you to make further changes to its location. When you are satisfied with its location, click the Array again to return to normal operation. RSSI For each station that is associated to the Array, the RSSI (Received Signal Strength Indicator) window shows the station’s RSSI value as measured by each IAP. In other words, the window shows the strength of the station’s signal at each radio. You may choose to display Unassociated Stations as well with a checkbox at the bottom of the window. Figure 68. Station RSSI Values By default, the RSSI is displayed numerically. You may display the relative strength using color if you select Colorize Intensity, with the strongest signals indicated by the most intense color. (Figure 68) If you select Graph, then the RSSI is shown on a representation of the Array, either colorized or numerically based Viewing Status on the Wi-Fi Array 153 Wi-Fi Array on your selection. (Figure 69) The stations are listed to the left of the Array — click on a station to show its RSSI values on the Array. Figure 69. Station RSSI Values — Colorized Graphical View In either graphical or tabular view, you may sort the rows based on any column that has an active column header, indicated when the mouse pointer changes to the hand icon . Click on the Refresh button to refresh the station list, or click in the Auto Refresh check box to instruct the Array to refresh this window automatically. See Also Station Status Windows RF Monitor Windows 154 Viewing Status on the Wi-Fi Array Wi-Fi Array Signal-to-Noise Ratio (SNR) For each station that is associated to the Array, the Signal-to-Noise Ratio (SNR) window shows the station’s SNR value as measured by each IAP. In other words, the window shows the SNR of the station’s signal at each IAP radio. The signalto-noise ratio can be very useful for determining the cause of poor performance at a station. A low value means that action may need to be taken to reduce sources of noise in the environment and/or improve the signal from the station. Figure 70. Station Signal-to-Noise Ratio Values You may choose to display Unassociated Stations as well with a checkbox at the bottom of the window. By default, the SNR is displayed numerically. (Figure 70) You may display the relative value using color if you select Colorize Intensity, with the highest SNR indicated by the most intense color. (Figure 71) If you select Graph, then the SNR is shown on a representation of the Array, either colorized or numerically based on your selection. The stations are listed to the left of the Array — click on a station to show its SNR values on the Array. Viewing Status on the Wi-Fi Array 155 Wi-Fi Array Figure 71. Station SNR Values — Colorized Graphical View In either graphical or tabular view, you may sort the rows based on any column that has an active column header, indicated when the mouse pointer changes to the hand icon . Click on the Refresh button to refresh the station list, or click in the Auto Refresh check box to instruct the Array to refresh this window automatically. See Also Station Status Windows RF Monitor Windows 156 Viewing Status on the Wi-Fi Array Wi-Fi Array Noise Floor For each station that is associated to the Array, the Noise Floor window shows the ambient noise affecting a station’s signal as measured by each IAP. The noise floor is the RSSI value when the station is not transmitting, sometimes called a Silence value. In other words, the window shows the noise floor of the station’s signal at each IAP radio. The noise floor value can be very useful for characterizing the environment of a station to determine the cause of poor performance. A relatively high value means that action may need to be taken to reduce sources of noise in the environment. Figure 72. Station Noise Floor Values You may choose to display Unassociated Stations as well with a checkbox at the bottom of the window. By default, the noise floor is displayed numerically. (Figure 72) You may display the relative value using color if you select Colorize Intensity, with the highest noise indicated by the most intense color. If you select Graph, then the ambient noise is shown on a representation of the Array, either colorized or numerically based on your selection.(Figure 73) The stations are listed to the left of the Array — click on a station to show its values on the Array. Viewing Status on the Wi-Fi Array 157 Wi-Fi Array Figure 73. Station Noise Floor Values — Colorized Graphical View In either graphical or tabular view, you may sort the rows based on any column that has an active column header, indicated when the mouse pointer changes to the hand icon . Click on the Refresh button to refresh the station list, or click in the Auto Refresh check box to instruct the Array to refresh this window automatically. See Also Station Status Windows RF Monitor Windows 158 Viewing Status on the Wi-Fi Array Wi-Fi Array Max by IAP This status-only window shows the maximum number of client stations that have historically been associated to the Array. For each IAP, the list shows the IAP’s state and channel number, the current number of stations associated, and the highest number of stations that have been associated over various periods of time: hour, day, week, month, and year. In other words, the Max Station Count shows the “high water mark” over the selected period of time — the maximum count of stations for the selected period, rather than a cumulative count of all stations that have associated. This information aids in network administration and in planning for additional capacity. Figure 74. Max by IAP You may click an IAP to go to the IAP Settings window. Click on the Refresh button to refresh the station list, or click Auto Refresh to instruct the Array to refresh this window automatically. See Also IAPs Station Status Windows Viewing Status on the Wi-Fi Array 159 Wi-Fi Array Statistics Windows The following Array Statistics windows are available: IAP Statistics Summary — provides an overview of the statistical data associated with all IAPs. Expands to show links for displaying detailed statistics for individual IAPs. Per-IAP Statistics — provides detailed statistics for an individual IAP. Network Statistics — displays statistical data associated with each network (Ethernet) interface. VLAN Statistics — provides statistical data associated with your assigned VLANs. WDS Statistics — provides statistical data for all WDS client and host links. Filter Statistics — provides statistical data for all configured filters. Station Statistics — provides statistical data associated with each station. IAP Statistics Summary This is a status only window that provides an overview of the statistical data associated with all IAPs. It also shows the channel used by each IAP. For detailed statistics for a specific IAP, see “Per-IAP Statistics” on page 161. Click the Unicast Stats Only checkbox on the lower left to filter the results, or clear the checkbox to show statistics for all wireless traffic. You can Refresh the data (update the window with the latest information) or Clear the data (reset all content to zero and begin counting again) at any time by clicking on the appropriate button. You can also click in the Auto Refresh check box to instruct the Array to refresh this window automatically. 160 Viewing Status on the Wi-Fi Array Wi-Fi Array Figure 75. IAP Statistics Summary Page See Also System Log Window Global Settings (IAP) Global Settings .11a Global Settings .11bg IAPs Per-IAP Statistics This is a status only window that provides detailed statistics for the selected IAP. If you click the link for IAP All in the left frame, each detailed statistic field will show the sum of that statistic for all IAPs. For a summary of statistics for all IAPs, see “IAP Statistics Summary” on page 160. Use the Display Percentages checkbox at the lower left to select the output format — check this option to express each statistic as a percentage of the total at the top of the column, or leave it blank to display raw numbers. A quick way to display the statistics for a particular IAP is by clicking the Array graphic at the bottom left of the WMI window. Click the desired IAP, and the selected statistics will be displayed. See “User Interface” on page 117. Viewing Status on the Wi-Fi Array 161 Wi-Fi Array Figure 76. Individual IAP Statistics Page (for IAP abg(n)1) You can Refresh the data (update the window with the latest information) or Clear the data (reset all content to zero and begin counting again) at any time by clicking on the appropriate button. You can also click in the Auto Refresh check box to instruct the Array to refresh this window automatically. See Also System Log Window Global Settings (IAP) Global Settings .11a Global Settings .11bg IAPs 162 Viewing Status on the Wi-Fi Array Wi-Fi Array Network Statistics This is a status only window that allows you to review statistical data associated with each network (Ethernet) interface and its activity. You can Refresh the data (update the window with the latest information) or Clear the data (reset all content to zero and begin counting again) at any time by clicking on the appropriate button. You can also click in the Auto Refresh check box to instruct the Array to refresh this window automatically. If you are experiencing problems on the Array, you may also want to print this window for your records. Figure 77. Network Statistics See Also DHCP Server DNS Settings Network Network Interfaces Viewing Status on the Wi-Fi Array 163 Wi-Fi Array VLAN Statistics This is a status only window that allows you to review statistical data associated with your assigned VLANs. You can refresh the information that is displayed on this page at any time by clicking on the Refresh button, or select the Auto Refresh option for this window to refresh automatically. The Clear All button at the lower left allows you to clear (zero out) all VLAN statistics. Figure 78. VLAN Statistics See Also VLAN Management VLANs 164 Viewing Status on the Wi-Fi Array Wi-Fi Array WDS Statistics The main WDS Statistics window provides statistical data for all WDS client and host links. To access data about a specific WDS client or host link, simply click on the desired link in the left frame to access the appropriate window. You may also choose to view a sum of the statistics for all client links, all host links, or all links (both client and host links). Figure 79. WDS Statistics See Also SSID Management WDS Viewing Status on the Wi-Fi Array 165 Wi-Fi Array Filter Statistics The Filter Statistics window provides statistical data for all configured filters. The name, state (enabled — on or off), and type (allow or deny) of each filter is shown. For enabled filters, this window shows the number of packets and bytes that met the filter criteria. Click on a column header to sort the rows based on that column. Click on a filter name to edit the filter settings. Figure 80. Filter Statistics See Also Filters Station Statistics This status-only window provides an overview of statistical data for all stations. Stations are listed by MAC address, and Receive and Transmit statistics are summarized for each. For detailed statistics for a specific station, click the desired MAC address in the Station column and see “Per-Station Statistics” on page 167. Figure 81. Station Statistics Note that you can clear the data for an individual station (see Per-Station Statistics), but you cannot clear the data for all stations using this window. 166 Viewing Status on the Wi-Fi Array Wi-Fi Array You can Refresh the data (update the window with the latest information) at any time by clicking on the appropriate button. You can also click in the Auto Refresh check box to instruct the Array to refresh this window automatically. See Also Per-Station Statistics Per-Station Statistics This window provides detailed statistics for the selected station. This window is accessed from the Station Statistics window — click the MAC address of the desired entry in the Station column to display its Per-Station Statistics window. Receive and Transmit statistics are listed by Rate — this is the data rate in Mbps. For a summary of statistics for all stations, see “Station Statistics” on page 166. You can Refresh the data (update the window with the latest information) or Clear the data (reset all content to zero and begin counting again) at any time by clicking on the appropriate button. You can also click in the Auto Refresh check box to instruct the Array to refresh this window automatically. Figure 82. Individual Station Statistics Page See Also Station Statistics Viewing Status on the Wi-Fi Array 167 Wi-Fi Array System Log Window This is a status only window that allows you to review the system log, where system alerts and messages are displayed. Although there are no configuration options available in this window, you do have the usual choice of deciding how the event messages are sorted by clicking in the column header for the desired field (Time Stamp, Priority, or Message). Time Stamp — sorts the list based on the time the event occurred. Priority — sorts the list based on the priority assigned to the message. Message — sorts the list based on the message category The displayed messages may be filtered by using the Filter Priority option, which allows control of the minimum priority level displayed. For example, you may choose (under Services >System Log) to log messages at or above Debug level but use Filter Priority to display only those at Information level and above. Figure 83. System Log 168 Viewing Status on the Wi-Fi Array Wi-Fi Array Use the Highlight Priority field if you wish to highlight messages at the selected priority level. Click on the Refresh button to refresh the message list, or click on the Clear button at the upper left to delete all messages. You can also click in the Auto Refresh check box to instruct the Array to refresh this window automatically. Note that there is a shortcut way to view system log messages. If you click Log Messages near the bottom of the left hand frame, WMI displays counts of log messages at different severity levels. Click a count to display just those messages in the System Log window. SeeFigure 42 on page 117 for more information. Viewing Status on the Wi-Fi Array 169 Wi-Fi Array 170 Viewing Status on the Wi-Fi Array
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39 Modify Date : 2010:12:30 12:24:07-08:00 Create Date : 2010:12:30 12:23:51-08:00 Metadata Date : 2010:12:30 12:24:07-08:00 Creator Tool : Adobe Illustrator CS3 Format : application/pdf Title : xirrus_PDF.book Creator : Shelly Document ID : uuid:5649148e-99e3-487c-9177-0d63bb2ab217 Instance ID : uuid:ba3f80b1-6232-4683-be9e-58b181c7b0ed Producer : Acrobat Distiller 9.4.0 (Windows) Has XFA : No Page Count : 190 Author : ShellyEXIF Metadata provided by EXIF.tools