Camden Door Control TXLF TXLF KeyFob Transmitter User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	3016967
Application ID	EUJq3y5M14fMO4JkBK1H1g==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	60.32kB (754015 bits)
Date Submitted	2016-06-03 00:00:00
Date Available	2016-06-03 00:00:00
Creation Date	2016-05-27 11:38:35
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2016-05-27 12:23:39
Document Title	Manual
Document Creator	Adobe InDesign CC (Macintosh)

Lazerpoint™ CM-TXLF Series
FOB Style Transmitters
Installation Instructions
will indicate a slow red flash — 1 flash per second. The unit will
still continue to function (transmit) for a time, but the battery
should be changed as soon as possible.
Section 1
General Description
Replacing the Battery
051
329-
01-0
A-2
PW
de
am
Camden Lazerpoint™ Radio Controls comprise the following
models:
• CM-TXLF-1, CM-TXLF-2, & CM-TXLF-4 Key Fob
Transmitters, as well as;
• CM-TX-9 Wall switch ready transmitter
• CM-TX-99 Plug-in 2-Channel Transmitter
• CM-RX-91 Basic Receiver
• CM-RX-92 Full function (dual relay) Receiver.
These instructions cover the TXLF transmitters.
Camden Key Fob transmitters utilize readily available
CR-2032 Lithium batteries, and special circuitry to assure
long life. A proprietary bi-colour LED circuit is used to
annunciate wireless activation, low battery, & Battery Gas
Gauge™ conditions.
Learning the Transmitter(s) to the Receiver
To learn the transmitter into an RX-91 or RX-92 receiver, press
the PB1 (or PB2) button on the Receiver using a small blunt
object such as a small blade screwdriver or similar. Within
10 seconds, press the button on the TXLF transmitter. The
Green LED Array will flash once to confirm enrollment. Repeat
withanyadditionaltransmitters.Pressingthelearnedtransmitter
again will signal the receiver that you are finished programming
and LED’s 1 & 2 will flash, in an alternating sequence.
Pressing the transmitter a third time will activate the relay
and corresponding LED, and also the device connected to the
relay contacts.
For multiple button FOBS – TXLF-2 & TXLF-4, learn the desired
button into one receiver, and the other button(s) into additional
receivers. (You could also learn Button 1 into Channel 1 of the
RX-92, and Button 2 into Channel 2 of the same RX-92.)
Refer to the RX-91 or RX-92 receiver for further programming
instructions.
Section 2
Installation
de
Separate 2 halves
PW
A-
20
1-
03
29
-0
51
Ca
am
Twist a coin in slot to
open transmitter case
Pan
ason
CR20 ic
32
3V
Remove PCB from
bottom half
md
en
de
am
051
329-
01-0
A-2
PW
Mounting
Camden TXLF Fobs can be attached to a key chain using the
included ring.
Fobs can also be mounted to a wheelchair by using accessory
number # CM-TXLFB Mounting Base. This unique accessory
converts any of the Mini Fobs to a full size unit which may be
clipped to a belt or sun-visor, or fastened to a desk or counter
for reception use. See our Lazerpoint™ spec sheet or TXLFB
Instruction manual for further details.
The CR-2032 battery is pre-installed in the Fob. Simply press
the button and observe the GREEN LED, which indicates
proper transmission.
Test the battery strength by pressing and holding the button
for approximately 5 seconds. The LED should flash RED
5 times, meaning the battery is at full capacity. This is the
Battery Gas Gauge™ feature. If the LED flashes RED only 1 - 2
times, you should change the battery for a fresh (new) one.
See instructions at right.
When the battery is low and needs to be changed, the LED
051
329-
01-0
A-2
PW
Remove old battery
Pan
ason
CR20 ic
32
3V
Turn over the PCB
Insert new battery
Insert PCB. Snap
the case together.
Page 1 of 2
Lazerpoint™ CM-TXLF Series FOB Style Transmitters Installation Instructions
Section 3
Assembly Instructions
Technical Data
Models:			
TXLF-1 (FVIN: 3A)
			TXLF-2 (FVIN: 3B)
			TXLF-4 (FVIN: 3C)
Buttons / Channels:
1, 2, & 4 respectively.
Frequency:
Operates in the 902 – 928 MHz
			ISM Band
Codes:			
1 million (20 bit) codes
Size:			
2 9/16” L x 1 9/16” W x 5/8” D
(102mm x 42mm x 16mm)
LED Indicator:		
Used for transmit status (green),
Low Battery, and Battery Gas
			Gauge™ indicator (red).
Power:			
1 x CR-2032 Lithium battery
Battery life:		
Minimum 115,000 operations
Range:			
Over 250 ft (76 m) open area
Temperature rating:
-40°F to 185°F (-40°C to +85°C)
Plastic
Case FOB
Top
Assembly
Plastic
Buttons
Translucent
Rubber
Membrane
Top + Bottom
Assemblies
Snap Together
Section 4
932
-0
01
-2
de
am
Camden Door Controls guarantees the CM TXLF series
transmitters to be free from manufacturing defects for
3 years from date of sale. If during the first 3 years a TXLF
transmitter fails to perform correctly, it may be returned to our
factory where it will be repaired or replaced (at our discretion)
without charge. Except as stated herein, Camden extends
no warranties expressed or implied regarding function,
performance or service.
05
Warranty
Circuit
Board
Bottom
Assembly
Batteries are exempt from this warranty.
Plastic Case
Bottom
Page 2 of 2
Lazerpoint™ CM-TXLF Series FOB Style Transmitters Installation Instructions
IC & FCC INFORMATION FOR USERS
IC: 8725A-TXLF
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
FCC ID: 2AHAB-TXLF
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications made to this equipment not expressly approved by Camden Door Controls could void the user’s authority to operate the equipment.
Push Buttons
Keypads
Strikes
5502 Timberlea Blvd.,
Mississauga, ON Canada
L4W 2T7
Magnetic Locks
Key Switches
www.camdencontrols.com
Toll Free: 1.877.226.3369
Relays & Timers
Access Control
File: CM-TXLF Transmitter
Manual.indd- Rev.5
Revised: 25/05/2016
Part No: 40-82B160
Page 3 of 3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2016:05:27 11:38:35-04:00
Creator                         : Adobe InDesign CC (Macintosh)
Modify Date                     : 2016:05:27 12:23:39-04:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2016:05:27 12:23:39-04:00
Creator Tool                    : Adobe InDesign CC (Macintosh)
Instance ID                     : uuid:c3f409fd-8c76-4130-ad4a-bd9678d50759
Original Document ID            : adobe:docid:indd:4b93cb07-78ae-11df-a09e-f6bb755e2087
Document ID                     : xmp.id:a53e39af-6e15-4701-8f7e-6da5f140977b
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:5185940c-7b3c-43bc-9de3-6e15095f4aa2
Derived From Document ID        : xmp.did:BA9925072820681188C6FAF4D655DD3C
Derived From Original Document ID: adobe:docid:indd:4b93cb07-78ae-11df-a09e-f6bb755e2087
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC (Macintosh)
History Changed                 : /
History When                    : 2016:05:27 11:38:35-04:00
Format                          : application/pdf
Title                           : Manual
Description                     : Manual
Subject                         : Manual
Producer                        : Adobe PDF Library 11.0
Trapped                         : False
Page Count                      : 3

EXIF Metadata provided by EXIF.tools