Canon Imageclass D780 Instruction Guide CRT_IMAGECLASSD700_EN

2015-03-09

: Canon Canon-Imageclass-D780-Instruction-Guide-587197 canon-imageclass-d780-instruction-guide-587197 canon pdf

Open the PDF directly: View PDF PDF.
Page Count: 8

For installation help and operational
instructions, call:
1-800-828-4040 1-800 OK CANON
U.S.A. CUSTOMERS CANADA CUSTOMERS
Output Tray
L50 S-Cartridge
Label
Connect the supplied power cord to the power
cord connector on the left side of the machine.
REMOVE ALL ITEMS FROM THE BOX
CONNECTING USING PARALLEL CABLE
or CONNECTING USING USB CABLE
CONNECTING THE POWER CORD
•POWER CORD
•TELEPHONE LINE*
•DOCUMENTATION
(Set-up Instructions, Reference Guide, Fax Guide*,
Limited Warranty Card, Registration Card**)
•DESTINATION LABEL*
•CD-ROM
Remove the shipping
attachment on the left
side using a coin.
Otherwise the scanning
unit of the machine is
locked and you cannot
make copies or send faxes.
Grasp the cartridge
with one hand, firmly
and slowly pull out
the sealing tape tab
with the other hand.
Remove the
sealing tape
completely.
Slide left until the
I4 mark appears.
When the power cord is
plugged into both the
machine and into a power
outlet, the machine will
automatically turn on. The
LCD displays PLEASE
WAIT. Please wait until
the LCD returns to the
Copy Mode standby
display.
Connect the supplied power cord to the power cord
connector on the left side of the machine.
Then connect the other end into a properly grounded Standard 120V three-prong outlet.
Copy Mode standby display
Remove the
cartridge from
its bag.
Remove the shipping
material.
REMOVE ALL SHIPPING MATERIALS
UNPACK MACHINE
1
INSTALL CARTRIDGE
2CONNECTIONS
4
SET-UP INSTRUCTIONS
imageCLASS D700 Series
Place the cartridge
on a flat and stable
surface, grip the
sealing tape tab
and snap in the
direction shown.
Make sure that the
tab is detached from
the cartridge.
Machine
Rock the cartridge
5 or 6 times to
distribute the
toner evenly.
* D780 Model
** U.S.A. only
FA7-5177 (010)
Printed in China
Position the arrow mark
on the cartridge towards
the inside of the
machine, and gently
slide the cartridge into
the machine as far as it
will go.
Close the cartridge cover
and slide the platen unit
back to the original
position.
2
1
1
Lift the platen unit
lever (1) and slide
the platen unit to
the left (2).
Open the
cartridge cover.
A
E
B
AB
C D
E F
C D
Grip the cassette
handle, and pull it
out towards you
until the cassette
comes to a stop.
Load the paper stack beneath
the cassette’s length guide (1)
and width guide’s claws (2).
Make sure that the paper stack does
not exceed the length and width
guide’s claws in the cassette. Failure
to do so will cause a paper jam.
Gently insert the cassette as
far as it will go.
Hook the tab on
the output tray
onto the opening
on the left side of
the machine.
LOAD PAPER / ATTACH OUTPUT TRAY
3
AB
C
PAR
USB interface connection
Connect to your computer using USB cable.
Connect to your computer using a USB cable.
USB interface connection.
PARALLEL
Parallel interface connection
Connect to your computer using a parallel cable.
Make sure the computer is turned off.
062002A
Insert the removed
shipping attachment
from STEP A into the
holder.
Keeping the cartridge
cover open, go
to section 2 -
INSTALL CARTRIDGE.
Keep the shipping
attachment in the holder
in case you need to
transport the machine.
F
The actual shape, quantity, and/or location of the
tape and shipping material may differ.
CRT_IMAGECLASSD700_EN 26/09/2003 17:11PM Page 1
For installation help and operational
instructions, call:
1-800-828-4040 1-800 OK CANON
U.S.A. CUSTOMERS CANADA CUSTOMERS
Output Tray
L50 S-Cartridge
Label
REMOVE ALL ITEMS FROM THE BOX
CONNECTING USING PARALLEL CABLE
or CONNECTING USING USB CABLE
CONNECTING THE POWER CORD
•POWER CORD
•TELEPHONE LINE*
•DOCUMENTATION
(Set-up Instructions, Reference Guide, Fax Guide*,
Limited Warranty Card, Registration Card**)
•DESTINATION LABEL*
•CD-ROM
Remove the shipping
attachment on the left
side using a coin.
Otherwise the scanning
unit of the machine is
locked and you cannot
make copies or send faxes.
Grasp the cartridge
with one hand, firmly
and slowly pull out
the sealing tape tab
with the other hand.
Remove the
sealing tape
completely.
Slide left until the
I4 mark appears.
When the power cord is
plugged into both the
machine and into a power
outlet, the machine will
automatically turn on. The
LCD displays PLEASE
WAIT. Please wait until
the LCD returns to the
Copy Mode standby
display.
Connect the supplied power cord to the power cord
connector on the left side of the machine.
Then connect the other end into a properly grounded Standard 120V three-prong outlet.
Copy Mode standby display
Remove the
cartridge from
its bag.
Remove the shipping
material.
REMOVE ALL SHIPPING MATERIALS
UNPACK MACHINE
1
INSTALL CARTRIDGE
2CONNECTIONS
4
SET-UP INSTRUCTIONS
imageCLASS D700 Series
Place the cartridge
on a flat and stable
surface, grip the
sealing tape tab
and snap in the
direction shown.
Make sure that the
tab is detached from
the cartridge.
Machine
Rock the cartridge
5 or 6 times to
distribute the
toner evenly.
* D780 Model
** U.S.A. only
FA7-5177 (010)
Printed in China
Position the arrow mark
on the cartridge towards
the inside of the
machine, and gently
slide the cartridge into
the machine as far as it
will go.
Close the cartridge cover
and slide the platen unit
back to the original
position.
2
1
1
Lift the platen unit
lever (1) and slide
the platen unit to
the left (2).
Open the
cartridge cover.
A
E
B
AB
C D
E F
C D
Grip the cassette
handle, and pull it
out towards you
until the cassette
comes to a stop.
Load the paper stack beneath
the cassette’s length guide (1)
and width guide’s claws (2).
Make sure that the paper stack does
not exceed the length and width
guide’s claws in the cassette. Failure
to do so will cause a paper jam.
Gently insert the cassette as
far as it will go.
Hook the tab on
the output tray
onto the opening
on the left side of
the machine.
LOAD PAPER / ATTACH OUTPUT TRAY
3
AB
C
PAR
USB interface connection
Connect to your computer using USB cable.
Connect to your computer using a USB cable.
USB interface connection.
PARALLEL
Parallel interface connection
Connect to your computer using a parallel cable.
Make sure the computer is turned off.
062002A
Insert the removed
shipping attachment
from STEP A into the
holder.
Keeping the cartridge
cover open, go
to section 2 -
INSTALL CARTRIDGE.
Keep the shipping
attachment in the holder
in case you need to
transport the machine.
F
The actual shape, quantity, and/or location of the
tape and shipping material may differ.
CRT_IMAGECLASSD700_EN 26/09/2003 17:11PM Page 1
For installation help and operational
instructions, call:
1-800-828-4040 1-800 OK CANON
U.S.A. CUSTOMERS CANADA CUSTOMERS
Output Tray
L50 S-Cartridge
Label
Connect the supplied power cord to the power
cord connector on the left side of the machine.
REMOVE ALL ITEMS FROM THE BOX
CONNECTING USING PARALLEL CABLE
or CONNECTING USING USB CABLE
CONNECTING THE POWER CORD
•POWER CORD
•TELEPHONE LINE*
•DOCUMENTATION
(Set-up Instructions, Reference Guide, Fax Guide*,
Limited Warranty Card, Registration Card**)
•DESTINATION LABEL*
•CD-ROM
Remove the shipping
attachment on the left
side using a coin.
Otherwise the scanning
unit of the machine is
locked and you cannot
make copies or send faxes.
Grasp the cartridge
with one hand, firmly
and slowly pull out
the sealing tape tab
with the other hand.
Remove the
sealing tape
completely.
Slide left until the
I4 mark appears.
When the power cord is
plugged into both the
machine and into a power
outlet, the machine will
automatically turn on. The
LCD displays PLEASE
WAIT. Please wait until
the LCD returns to the
Copy Mode standby
display.
Connect the supplied power cord to the power cord
connector on the left side of the machine.
Then connect the other end into a properly grounded Standard 120V three-prong outlet.
Copy Mode standby display
Remove the
cartridge from
its bag.
Remove the shipping
material.
REMOVE ALL SHIPPING MATERIALS
UNPACK MACHINE
1
INSTALL CARTRIDGE
2CONNECTIONS
4
SET-UP INSTRUCTIONS
imageCLASS D700 Series
Place the cartridge
on a flat and stable
surface, grip the
sealing tape tab
and snap in the
direction shown.
Make sure that the
tab is detached from
the cartridge.
Machine
Rock the cartridge
5 or 6 times to
distribute the
toner evenly.
* D780 Model
** U.S.A. only
FA7-5177 (010)
Printed in China
Position the arrow mark
on the cartridge towards
the inside of the
machine, and gently
slide the cartridge into
the machine as far as it
will go.
Close the cartridge cover
and slide the platen unit
back to the original
position.
2
1
1
Lift the platen unit
lever (1) and slide
the platen unit to
the left (2).
Open the
cartridge cover.
A
E
B
AB
C D
E F
C D
Grip the cassette
handle, and pull it
out towards you
until the cassette
comes to a stop.
Load the paper stack beneath
the cassette’s length guide (1)
and width guide’s claws (2).
Make sure that the paper stack does
not exceed the length and width
guide’s claws in the cassette. Failure
to do so will cause a paper jam.
Gently insert the cassette as
far as it will go.
Hook the tab on
the output tray
onto the opening
on the left side of
the machine.
LOAD PAPER / ATTACH OUTPUT TRAY
3
AB
C
PAR
USB interface connection
Connect to your computer using USB cable.
Connect to your computer using a USB cable.
USB interface connection.
PARALLEL
Parallel interface connection
Connect to your computer using a parallel cable.
Make sure the computer is turned off.
062002A
Insert the removed
shipping attachment
from STEP A into the
holder.
Keeping the cartridge
cover open, go
to section 2 -
INSTALL CARTRIDGE.
Keep the shipping
attachment in the holder
in case you need to
transport the machine.
F
The actual shape, quantity, and/or location of the
tape and shipping material may differ.
CRT_IMAGECLASSD700_EN 26/09/2003 17:11PM Page 1
For installation help and operational
instructions, call:
1-800-828-4040 1-800 OK CANON
U.S.A. CUSTOMERS CANADA CUSTOMERS
Output Tray
L50 S-Cartridge
Label
Connect the supplied power cord to the power
cord connector on the left side of the machine.
REMOVE ALL ITEMS FROM THE BOX
CONNECTING USING PARALLEL CABLE
or CONNECTING USING USB CABLE
CONNECTING THE POWER CORD
•POWER CORD
•TELEPHONE LINE*
•DOCUMENTATION
(Set-up Instructions, Reference Guide, Fax Guide*,
Limited Warranty Card, Registration Card**)
•DESTINATION LABEL*
•CD-ROM
Remove the shipping
attachment on the left
side using a coin.
Otherwise the scanning
unit of the machine is
locked and you cannot
make copies or send faxes.
Grasp the cartridge
with one hand, firmly
and slowly pull out
the sealing tape tab
with the other hand.
Remove the
sealing tape
completely.
Slide left until the
I4 mark appears.
When the power cord is
plugged into both the
machine and into a power
outlet, the machine will
automatically turn on. The
LCD displays PLEASE
WAIT. Please wait until
the LCD returns to the
Copy Mode standby
display.
Connect the supplied power cord to the power cord
connector on the left side of the machine.
Then connect the other end into a properly grounded Standard 120V three-prong outlet.
Copy Mode standby display
Remove the
cartridge from
its bag.
Remove the shipping
material.
REMOVE ALL SHIPPING MATERIALS
UNPACK MACHINE
1
INSTALL CARTRIDGE
2CONNECTIONS
4
SET-UP INSTRUCTIONS
imageCLASS D700 Series
Place the cartridge
on a flat and stable
surface, grip the
sealing tape tab
and snap in the
direction shown.
Make sure that the
tab is detached from
the cartridge.
Machine
Rock the cartridge
5 or 6 times to
distribute the
toner evenly.
* D780 Model
** U.S.A. only
FA7-5177 (010)
Printed in China
Position the arrow mark
on the cartridge towards
the inside of the
machine, and gently
slide the cartridge into
the machine as far as it
will go.
Close the cartridge cover
and slide the platen unit
back to the original
position.
2
1
1
Lift the platen unit
lever (1) and slide
the platen unit to
the left (2).
Open the
cartridge cover.
A
E
B
AB
C D
E F
C D
Grip the cassette
handle, and pull it
out towards you
until the cassette
comes to a stop.
Load the paper stack beneath
the cassette’s length guide (1)
and width guide’s claws (2).
Make sure that the paper stack does
not exceed the length and width
guide’s claws in the cassette. Failure
to do so will cause a paper jam.
Gently insert the cassette as
far as it will go.
Hook the tab on
the output tray
onto the opening
on the left side of
the machine.
LOAD PAPER / ATTACH OUTPUT TRAY
3
AB
C
PAR
USB interface connection
Connect to your computer using USB cable.
Connect to your computer using a USB cable.
USB interface connection.
PARALLEL
Parallel interface connection
Connect to your computer using a parallel cable.
Make sure the computer is turned off.
062002A
Insert the removed
shipping attachment
from STEP A into the
holder.
Keeping the cartridge
cover open, go
to section 2 -
INSTALL CARTRIDGE.
Keep the shipping
attachment in the holder
in case you need to
transport the machine.
F
The actual shape, quantity, and/or location of the
tape and shipping material may differ.
CRT_IMAGECLASSD700_EN 26/09/2003 17:11PM Page 1
: Telephone line jack
: External device jack
Press FAX to switch the machine to Fax Mode.
Press RECEIVE MODE until the mode you want appears:
You can select from the following modes:
FAX ONLY: if you use your machine to receive only faxes.
DRPD: to distinguish between fax and voice calls by using
Distinctive Ring Patterns.
MANUAL: you can receive faxes by pressing START before
hanging up the handset on the telephone.
AnsMode: if you want to receive faxes automatically and route
voice calls to an answering machine.
FaxTel: when a telephone is connected to the machine, the machine automatically switches between faxes and voice calls.
•Telephone or answering machine
•Telephone and answering machine
•Telephone and modem (external modem)
•Built-in computer modem and telephone
Press SET.
The selected receive mode is set and the machine returns to standby mode. The current date and the selected receive mode are
displayed.
•The machine does not ring when it receives a fax in FaxOnly. If you want to be alerted when a fax is received, connect a telephone
to the machine, and enable the INCOMING RING setting. (---> Fax Guide).
•For AnsMode, you need to connect an answering machine or a telephone with an answering machine to your machine (see below).
•Follow these guidelines when using the machine with an answering machine:
— Set the answering machine to answer on the first or second ring.
— When recording the outgoing message on the answering machine, the entire message must be no longer than 15 seconds.
ex. FAX 06/20/2003 17:08
Manual STANDARD
ex. RECEIVE MODE
Manual
Make sure the computer is turned off.
Make sure the machine’s power cord is plugged into a power outlet and the
machine is connected to your computer using a parallel cable (cable not included).
Turn on the computer. Start up Windows. PLUG and PLAY will activate and the
FOUND NEW HARDWARE WIZARD (In Windows 95, New Hardware or Device
Wizard) dialog box appears. Click CANCEL.
Set the CD-ROM into the CD-ROM drive of your computer.
Click NEXT.
Add Printer
Wizard dialog box
(Local printer/
Network printer)
selection appears.
Select the printer port,
the machine is
connected to
(usually LPT1:),
then click NEXT.
Add Printer Wizard
dialog box (Printer
name) appears.
If you select a port,
other than the port
D700 is connected to,
COM: or FILE: port,
the machine will not
print.
INSTALLING FROM CD-ROM MENU (Windows 98 / Me)
1) Make sure the computer is turned off.
2) Make sure the power cord of the machine is plugged into the power outlet and the machine is connected to your computer
(cable not included).
3) Turn on the computer and ADD NEW HARDWARE WIZARD dialog box appears. Follow the instructions on screen to activate
PLUG and PLAY installation. When you are asked to select the directory that contains the CAPT, browse to D:\English\Win9x or
D:\English\WinME, if your CD-ROM drive is drive D. For installation instructions using PLUG and PLAY for USB Port, ----> Printer Guide.
INSTALLING FROM CD-ROM MENU (Windows 2000 / XP)
1) Make sure the computer is turned off.
2) Make sure the power cord of the machine is plugged into the power outlet and the machine is connected to your computer,
then turn the computer on.
3) As the USB class driver is automatically detected, perform the same steps as described for “PARALLEL CABLE (Windows XP)” of
“INSTALL PRINTER DRIVER”. When you are asked to select the printer port, select either
USBPRNXX or USBXXX (XX or XXX represents a set of numbers).
For installation instructions using PLUG and PLAY or ADD PRINTER WIZARD for USB Port, ----> Printer Guide.
Windows 95 / 98 / Me Windows XP
Use BROWSE… to
select the directory that
contains the CAPT.
For example, if you are
using the CD-ROM to
install the CAPT on
Windows 95/98, and
your CD-ROM drive is
drive D:, browse to
D:\English\Win9x, and
click OK.
Use BROWSE…
to select the directory
that contains the
CAPT.
Click FINISH.
If you wish to change
printer name, type a
new name into the text
box.
*If you want to set this
printer as the default
printer, select YES.
Driver file selection
dialog appears.
Click NEXT.
Add Printer Wizard
dialog box
(Printer name)
appears.
*If this printer is
shared with other
computers, check on
SHARED option.
Click NEXT.
You can also modify
this setting after
installation, using
Sharing tab from the
Printer Properties.
Click NEXT.
If you wish to change
printer name, type a
new name into the text
box.
*If you want to set this
printer as the default
printer, select YES.
Click NEXT.
Click YES if you
want to print a
test page, or NO
if you do not
want to print a
test page.
If you opted to print a test page, the test page will be
printed after the installation is complete. If the test page
printed correctly, click YES.
When installation is complete, the following dialog box
appears. Click OK.
Make sure the computer is turned off.
Make sure the power cord of the machine is plugged into the power outlet and the machine
is connected to your computer using parallel cable.
Turn on the computer. Start up Windows XP. PLUG and PLAY will activate and the FOUND
NEW HARDWARE WIZARD dialog box appears. Click CANCEL. For installations, using
PLUG and PLAY function of your computer, -----> Printer Guide.
Set the CD-ROM into the CD-ROM drive of your computer.
Click
HAVE DISK…in the
MANUFACTURERS/
PRINTERS dialog box.
THE INSTALL FROM
DISK dialog box
appears. USB CABLE — Windows 98 / Me / 2000 / XP
Click Canon
PC1200/iC D700
INSTALL button.
ADD PRINTER
WIZARD dialog box
appears.
Select LOCAL
PRINTER, then click
NEXT.
Add Printer
Wizard dialog box
(Manufacturers/printers)
selection appears.
Driver file selection
dialog appears.
Click NEXT.
Printer port selection
dialog box appears.
Click
HAVE DISK… in the
MANUFACTURERS/
PRINTERS dialog box.
THE INSTALL FROM
DISK dialog box
appears.
When the installation
is complete, the
following dialog box
appears.
To close the dialog
box, click OK.
Select LOCAL
PRINTER ATTACHED
TO THIS COMPUTER,
then click NEXT.
Printer port selection
dialog box appears.
AUTOMATICALLY
DETECT AND
INSTALL MY PLUG
AND PLAY PRINTER
is not recommended.
Click Canon
PC1200/iC D700
INSTALL button.
ADD PRINTER
WIZARD dialog box
appears. Click NEXT.
Check on the use
following port: Select
the printer port, the
machine is connected
to (usually LPT1:
Recommended printer
port), then click NEXT.
Add Printer Wizard
dialog box
(Manufacturers/
Printers selection)
appears.
Click FINISH.
INSTALL PRINTER DRIVER (CAPT)
6
SET FAX RECEIVE MODE (D780)
5
A
B
C
D
A
B
C
D
E F
G H
IJ
EF
G H
L M
N O
P
IJ
K
K
L
M
L
Machine
Telephone
line
Telephone or
answering machine
L
Machine
Telephone
line
Telephone
Answering
machine
LINE TEL.
L
Machine
Telephone
line
Telephone
Modem
LINE TEL.
Computer
Serial
Connector
L
Machine
Telephone
Computer
LINE TEL.
L
of the line to the telephone
jack on your wall.
1. Connect the supplied telephone line to the
Jack, then connect the other end of the line
to the telephone jack on your wall.
2. When you require to send and
receive both faxes and voice calls,
connect the line from the telephone
or answering machine to the Jack.
CONNECTING THE TELEPHONE LINE
AND AN EXTERNAL DEVICE
(Only for the D780 model)
The machine has two jacks on the left side for
the following connections:
: Telephone Line
: External device, such as telephone or answering machine.
CONNECT EXTERNAL
DEVICES AS FOLLOWS:
L
L
NOTE: For Windows 2000/NT 4.0 - see Printer Guide on CD-ROM
A
B
C
D
PARALLEL CABLEPARALLEL CABLE
For example, if your
CD-ROM drive is drive
D:, browse to
D:/English/WinXP,
click OPEN.
Make sure the folder is
selected in the COPY
MANUFACTURER’S
FILES FROM box,
then click OK.
*If there already are other printer drivers installed on your computer,
this option may not be displayed.
*If there already are other printer drivers installed on your computer,
this option may not be displayed.
1
2
1
2
3
*Depending on your computer settings, this option may not be displayed.
CRT_IMAGECLASSD700_EN 26/09/2003 17:11PM Page 2
: Telephone line jack
: External device jack
Press FAX to switch the machine to Fax Mode.
Press RECEIVE MODE until the mode you want appears:
You can select from the following modes:
FAX ONLY: if you use your machine to receive only faxes.
DRPD: to distinguish between fax and voice calls by using
Distinctive Ring Patterns.
MANUAL: you can receive faxes by pressing START before
hanging up the handset on the telephone.
AnsMode: if you want to receive faxes automatically and route
voice calls to an answering machine.
FaxTel: when a telephone is connected to the machine, the machine automatically switches between faxes and voice calls.
•Telephone or answering machine
•Telephone and answering machine
•Telephone and modem (external modem)
•Built-in computer modem and telephone
Press SET.
The selected receive mode is set and the machine returns to standby mode. The current date and the selected receive mode are
displayed.
•The machine does not ring when it receives a fax in FaxOnly. If you want to be alerted when a fax is received, connect a telephone
to the machine, and enable the INCOMING RING setting. (---> Fax Guide).
•For AnsMode, you need to connect an answering machine or a telephone with an answering machine to your machine (see below).
•Follow these guidelines when using the machine with an answering machine:
— Set the answering machine to answer on the first or second ring.
— When recording the outgoing message on the answering machine, the entire message must be no longer than 15 seconds.
ex. FAX 06/20/2003 17:08
Manual STANDARD
ex. RECEIVE MODE
Manual
Make sure the computer is turned off.
Make sure the machine’s power cord is plugged into a power outlet and the
machine is connected to your computer using a parallel cable (cable not included).
Turn on the computer. Start up Windows. PLUG and PLAY will activate and the
FOUND NEW HARDWARE WIZARD (In Windows 95, New Hardware or Device
Wizard) dialog box appears. Click CANCEL.
Set the CD-ROM into the CD-ROM drive of your computer.
Click NEXT.
Add Printer
Wizard dialog box
(Local printer/
Network printer)
selection appears.
Select the printer port,
the machine is
connected to
(usually LPT1:),
then click NEXT.
Add Printer Wizard
dialog box (Printer
name) appears.
If you select a port,
other than the port
D700 is connected to,
COM: or FILE: port,
the machine will not
print.
INSTALLING FROM CD-ROM MENU (Windows 98 / Me)
1) Make sure the computer is turned off.
2) Make sure the power cord of the machine is plugged into the power outlet and the machine is connected to your computer
(cable not included).
3) Turn on the computer and ADD NEW HARDWARE WIZARD dialog box appears. Follow the instructions on screen to activate
PLUG and PLAY installation. When you are asked to select the directory that contains the CAPT, browse to D:\English\Win9x or
D:\English\WinME, if your CD-ROM drive is drive D. For installation instructions using PLUG and PLAY for USB Port, ----> Printer Guide.
INSTALLING FROM CD-ROM MENU (Windows 2000 / XP)
1) Make sure the computer is turned off.
2) Make sure the power cord of the machine is plugged into the power outlet and the machine is connected to your computer,
then turn the computer on.
3) As the USB class driver is automatically detected, perform the same steps as described for “PARALLEL CABLE (Windows XP)” of
“INSTALL PRINTER DRIVER”. When you are asked to select the printer port, select either
USBPRNXX or USBXXX (XX or XXX represents a set of numbers).
For installation instructions using PLUG and PLAY or ADD PRINTER WIZARD for USB Port, ----> Printer Guide.
Windows 95 / 98 / Me Windows XP
Use BROWSE… to
select the directory that
contains the CAPT.
For example, if you are
using the CD-ROM to
install the CAPT on
Windows 95/98, and
your CD-ROM drive is
drive D:, browse to
D:\English\Win9x, and
click OK.
Use BROWSE…
to select the directory
that contains the
CAPT.
Click FINISH.
If you wish to change
printer name, type a
new name into the text
box.
*If you want to set this
printer as the default
printer, select YES.
Driver file selection
dialog appears.
Click NEXT.
Add Printer Wizard
dialog box
(Printer name)
appears.
*If this printer is
shared with other
computers, check on
SHARED option.
Click NEXT.
You can also modify
this setting after
installation, using
Sharing tab from the
Printer Properties.
Click NEXT.
If you wish to change
printer name, type a
new name into the text
box.
*If you want to set this
printer as the default
printer, select YES.
Click NEXT.
Click YES if you
want to print a
test page, or NO
if you do not
want to print a
test page.
If you opted to print a test page, the test page will be
printed after the installation is complete. If the test page
printed correctly, click YES.
When installation is complete, the following dialog box
appears. Click OK.
Make sure the computer is turned off.
Make sure the power cord of the machine is plugged into the power outlet and the machine
is connected to your computer using parallel cable.
Turn on the computer. Start up Windows XP. PLUG and PLAY will activate and the FOUND
NEW HARDWARE WIZARD dialog box appears. Click CANCEL. For installations, using
PLUG and PLAY function of your computer, -----> Printer Guide.
Set the CD-ROM into the CD-ROM drive of your computer.
Click
HAVE DISK…in the
MANUFACTURERS/
PRINTERS dialog box.
THE INSTALL FROM
DISK dialog box
appears. USB CABLE — Windows 98 / Me / 2000 / XP
Click Canon
PC1200/iC D700
INSTALL button.
ADD PRINTER
WIZARD dialog box
appears.
Select LOCAL
PRINTER, then click
NEXT.
Add Printer
Wizard dialog box
(Manufacturers/printers)
selection appears.
Driver file selection
dialog appears.
Click NEXT.
Printer port selection
dialog box appears.
Click
HAVE DISK… in the
MANUFACTURERS/
PRINTERS dialog box.
THE INSTALL FROM
DISK dialog box
appears.
When the installation
is complete, the
following dialog box
appears.
To close the dialog
box, click OK.
Select LOCAL
PRINTER ATTACHED
TO THIS COMPUTER,
then click NEXT.
Printer port selection
dialog box appears.
AUTOMATICALLY
DETECT AND
INSTALL MY PLUG
AND PLAY PRINTER
is not recommended.
Click Canon
PC1200/iC D700
INSTALL button.
ADD PRINTER
WIZARD dialog box
appears. Click NEXT.
Check on the use
following port: Select
the printer port, the
machine is connected
to (usually LPT1:
Recommended printer
port), then click NEXT.
Add Printer Wizard
dialog box
(Manufacturers/
Printers selection)
appears.
Click FINISH.
INSTALL PRINTER DRIVER (CAPT)
6
SET FAX RECEIVE MODE (D780)
5
A
B
C
D
A
B
C
D
E F
G H
IJ
EF
G H
L M
N O
P
IJ
K
K
L
M
L
Machine
Telephone
line
Telephone or
answering machine
L
Machine
Telephone
line
Telephone
Answering
machine
LINE TEL.
L
Machine
Telephone
line
Telephone
Modem
LINE TEL.
Computer
Serial
Connector
L
Machine
Telephone
Computer
LINE TEL.
L
of the line to the telephone
jack on your wall.
1. Connect the supplied telephone line to the
Jack, then connect the other end of the line
to the telephone jack on your wall.
2. When you require to send and
receive both faxes and voice calls,
connect the line from the telephone
or answering machine to the Jack.
CONNECTING THE TELEPHONE LINE
AND AN EXTERNAL DEVICE
(Only for the D780 model)
The machine has two jacks on the left side for
the following connections:
: Telephone Line
: External device, such as telephone or answering machine.
CONNECT EXTERNAL
DEVICES AS FOLLOWS:
L
L
NOTE: For Windows 2000/NT 4.0 - see Printer Guide on CD-ROM
A
B
C
D
PARALLEL CABLEPARALLEL CABLE
For example, if your
CD-ROM drive is drive
D:, browse to
D:/English/WinXP,
click OPEN.
Make sure the folder is
selected in the COPY
MANUFACTURER’S
FILES FROM box,
then click OK.
*If there already are other printer drivers installed on your computer,
this option may not be displayed.
*If there already are other printer drivers installed on your computer,
this option may not be displayed.
1
2
1
2
3
*Depending on your computer settings, this option may not be displayed.
CRT_IMAGECLASSD700_EN 26/09/2003 17:11PM Page 2
: Telephone line jack
: External device jack
Press FAX to switch the machine to Fax Mode.
Press RECEIVE MODE until the mode you want appears:
You can select from the following modes:
FAX ONLY: if you use your machine to receive only faxes.
DRPD: to distinguish between fax and voice calls by using
Distinctive Ring Patterns.
MANUAL: you can receive faxes by pressing START before
hanging up the handset on the telephone.
AnsMode: if you want to receive faxes automatically and route
voice calls to an answering machine.
FaxTel: when a telephone is connected to the machine, the machine automatically switches between faxes and voice calls.
•Telephone or answering machine
•Telephone and answering machine
•Telephone and modem (external modem)
•Built-in computer modem and telephone
Press SET.
The selected receive mode is set and the machine returns to standby mode. The current date and the selected receive mode are
displayed.
•The machine does not ring when it receives a fax in FaxOnly. If you want to be alerted when a fax is received, connect a telephone
to the machine, and enable the INCOMING RING setting. (---> Fax Guide).
•For AnsMode, you need to connect an answering machine or a telephone with an answering machine to your machine (see below).
•Follow these guidelines when using the machine with an answering machine:
— Set the answering machine to answer on the first or second ring.
— When recording the outgoing message on the answering machine, the entire message must be no longer than 15 seconds.
ex. FAX 06/20/2003 17:08
Manual STANDARD
ex. RECEIVE MODE
Manual
Make sure the computer is turned off.
Make sure the machine’s power cord is plugged into a power outlet and the
machine is connected to your computer using a parallel cable (cable not included).
Turn on the computer. Start up Windows. PLUG and PLAY will activate and the
FOUND NEW HARDWARE WIZARD (In Windows 95, New Hardware or Device
Wizard) dialog box appears. Click CANCEL.
Set the CD-ROM into the CD-ROM drive of your computer.
Click NEXT.
Add Printer
Wizard dialog box
(Local printer/
Network printer)
selection appears.
Select the printer port,
the machine is
connected to
(usually LPT1:),
then click NEXT.
Add Printer Wizard
dialog box (Printer
name) appears.
If you select a port,
other than the port
D700 is connected to,
COM: or FILE: port,
the machine will not
print.
INSTALLING FROM CD-ROM MENU (Windows 98 / Me)
1) Make sure the computer is turned off.
2) Make sure the power cord of the machine is plugged into the power outlet and the machine is connected to your computer
(cable not included).
3) Turn on the computer and ADD NEW HARDWARE WIZARD dialog box appears. Follow the instructions on screen to activate
PLUG and PLAY installation. When you are asked to select the directory that contains the CAPT, browse to D:\English\Win9x or
D:\English\WinME, if your CD-ROM drive is drive D. For installation instructions using PLUG and PLAY for USB Port, ----> Printer Guide.
INSTALLING FROM CD-ROM MENU (Windows 2000 / XP)
1) Make sure the computer is turned off.
2) Make sure the power cord of the machine is plugged into the power outlet and the machine is connected to your computer,
then turn the computer on.
3) As the USB class driver is automatically detected, perform the same steps as described for “PARALLEL CABLE (Windows XP)” of
“INSTALL PRINTER DRIVER”. When you are asked to select the printer port, select either
USBPRNXX or USBXXX (XX or XXX represents a set of numbers).
For installation instructions using PLUG and PLAY or ADD PRINTER WIZARD for USB Port, ----> Printer Guide.
Windows 95 / 98 / Me Windows XP
Use BROWSE… to
select the directory that
contains the CAPT.
For example, if you are
using the CD-ROM to
install the CAPT on
Windows 95/98, and
your CD-ROM drive is
drive D:, browse to
D:\English\Win9x, and
click OK.
Use BROWSE…
to select the directory
that contains the
CAPT.
Click FINISH.
If you wish to change
printer name, type a
new name into the text
box.
*If you want to set this
printer as the default
printer, select YES.
Driver file selection
dialog appears.
Click NEXT.
Add Printer Wizard
dialog box
(Printer name)
appears.
*If this printer is
shared with other
computers, check on
SHARED option.
Click NEXT.
You can also modify
this setting after
installation, using
Sharing tab from the
Printer Properties.
Click NEXT.
If you wish to change
printer name, type a
new name into the text
box.
*If you want to set this
printer as the default
printer, select YES.
Click NEXT.
Click YES if you
want to print a
test page, or NO
if you do not
want to print a
test page.
If you opted to print a test page, the test page will be
printed after the installation is complete. If the test page
printed correctly, click YES.
When installation is complete, the following dialog box
appears. Click OK.
Make sure the computer is turned off.
Make sure the power cord of the machine is plugged into the power outlet and the machine
is connected to your computer using parallel cable.
Turn on the computer. Start up Windows XP. PLUG and PLAY will activate and the FOUND
NEW HARDWARE WIZARD dialog box appears. Click CANCEL. For installations, using
PLUG and PLAY function of your computer, -----> Printer Guide.
Set the CD-ROM into the CD-ROM drive of your computer.
Click
HAVE DISK…in the
MANUFACTURERS/
PRINTERS dialog box.
THE INSTALL FROM
DISK dialog box
appears. USB CABLE — Windows 98 / Me / 2000 / XP
Click Canon
PC1200/iC D700
INSTALL button.
ADD PRINTER
WIZARD dialog box
appears.
Select LOCAL
PRINTER, then click
NEXT.
Add Printer
Wizard dialog box
(Manufacturers/printers)
selection appears.
Driver file selection
dialog appears.
Click NEXT.
Printer port selection
dialog box appears.
Click
HAVE DISK… in the
MANUFACTURERS/
PRINTERS dialog box.
THE INSTALL FROM
DISK dialog box
appears.
When the installation
is complete, the
following dialog box
appears.
To close the dialog
box, click OK.
Select LOCAL
PRINTER ATTACHED
TO THIS COMPUTER,
then click NEXT.
Printer port selection
dialog box appears.
AUTOMATICALLY
DETECT AND
INSTALL MY PLUG
AND PLAY PRINTER
is not recommended.
Click Canon
PC1200/iC D700
INSTALL button.
ADD PRINTER
WIZARD dialog box
appears. Click NEXT.
Check on the use
following port: Select
the printer port, the
machine is connected
to (usually LPT1:
Recommended printer
port), then click NEXT.
Add Printer Wizard
dialog box
(Manufacturers/
Printers selection)
appears.
Click FINISH.
INSTALL PRINTER DRIVER (CAPT)
6
SET FAX RECEIVE MODE (D780)
5
A
B
C
D
A
B
C
D
E F
G H
IJ
EF
G H
L M
N O
P
IJ
K
K
L
M
L
Machine
Telephone
line
Telephone or
answering machine
L
Machine
Telephone
line
Telephone
Answering
machine
LINE TEL.
L
Machine
Telephone
line
Telephone
Modem
LINE TEL.
Computer
Serial
Connector
L
Machine
Telephone
Computer
LINE TEL.
L
of the line to the telephone
jack on your wall.
1. Connect the supplied telephone line to the
Jack, then connect the other end of the line
to the telephone jack on your wall.
2. When you require to send and
receive both faxes and voice calls,
connect the line from the telephone
or answering machine to the Jack.
CONNECTING THE TELEPHONE LINE
AND AN EXTERNAL DEVICE
(Only for the D780 model)
The machine has two jacks on the left side for
the following connections:
: Telephone Line
: External device, such as telephone or answering machine.
CONNECT EXTERNAL
DEVICES AS FOLLOWS:
L
L
NOTE: For Windows 2000/NT 4.0 - see Printer Guide on CD-ROM
A
B
C
D
PARALLEL CABLEPARALLEL CABLE
For example, if your
CD-ROM drive is drive
D:, browse to
D:/English/WinXP,
click OPEN.
Make sure the folder is
selected in the COPY
MANUFACTURER’S
FILES FROM box,
then click OK.
*If there already are other printer drivers installed on your computer,
this option may not be displayed.
*If there already are other printer drivers installed on your computer,
this option may not be displayed.
1
2
1
2
3
*Depending on your computer settings, this option may not be displayed.
CRT_IMAGECLASSD700_EN 26/09/2003 17:11PM Page 2
: Telephone line jack
: External device jack
Press FAX to switch the machine to Fax Mode.
Press RECEIVE MODE until the mode you want appears:
You can select from the following modes:
FAX ONLY: if you use your machine to receive only faxes.
DRPD: to distinguish between fax and voice calls by using
Distinctive Ring Patterns.
MANUAL: you can receive faxes by pressing START before
hanging up the handset on the telephone.
AnsMode: if you want to receive faxes automatically and route
voice calls to an answering machine.
FaxTel: when a telephone is connected to the machine, the machine automatically switches between faxes and voice calls.
•Telephone or answering machine
•Telephone and answering machine
•Telephone and modem (external modem)
•Built-in computer modem and telephone
Press SET.
The selected receive mode is set and the machine returns to standby mode. The current date and the selected receive mode are
displayed.
•The machine does not ring when it receives a fax in FaxOnly. If you want to be alerted when a fax is received, connect a telephone
to the machine, and enable the INCOMING RING setting. (---> Fax Guide).
•For AnsMode, you need to connect an answering machine or a telephone with an answering machine to your machine (see below).
•Follow these guidelines when using the machine with an answering machine:
— Set the answering machine to answer on the first or second ring.
— When recording the outgoing message on the answering machine, the entire message must be no longer than 15 seconds.
ex. FAX 06/20/2003 17:08
Manual STANDARD
ex. RECEIVE MODE
Manual
Make sure the computer is turned off.
Make sure the machine’s power cord is plugged into a power outlet and the
machine is connected to your computer using a parallel cable (cable not included).
Turn on the computer. Start up Windows. PLUG and PLAY will activate and the
FOUND NEW HARDWARE WIZARD (In Windows 95, New Hardware or Device
Wizard) dialog box appears. Click CANCEL.
Set the CD-ROM into the CD-ROM drive of your computer.
Click NEXT.
Add Printer
Wizard dialog box
(Local printer/
Network printer)
selection appears.
Select the printer port,
the machine is
connected to
(usually LPT1:),
then click NEXT.
Add Printer Wizard
dialog box (Printer
name) appears.
If you select a port,
other than the port
D700 is connected to,
COM: or FILE: port,
the machine will not
print.
INSTALLING FROM CD-ROM MENU (Windows 98 / Me)
1) Make sure the computer is turned off.
2) Make sure the power cord of the machine is plugged into the power outlet and the machine is connected to your computer
(cable not included).
3) Turn on the computer and ADD NEW HARDWARE WIZARD dialog box appears. Follow the instructions on screen to activate
PLUG and PLAY installation. When you are asked to select the directory that contains the CAPT, browse to D:\English\Win9x or
D:\English\WinME, if your CD-ROM drive is drive D. For installation instructions using PLUG and PLAY for USB Port, ----> Printer Guide.
INSTALLING FROM CD-ROM MENU (Windows 2000 / XP)
1) Make sure the computer is turned off.
2) Make sure the power cord of the machine is plugged into the power outlet and the machine is connected to your computer,
then turn the computer on.
3) As the USB class driver is automatically detected, perform the same steps as described for “PARALLEL CABLE (Windows XP)” of
“INSTALL PRINTER DRIVER”. When you are asked to select the printer port, select either
USBPRNXX or USBXXX (XX or XXX represents a set of numbers).
For installation instructions using PLUG and PLAY or ADD PRINTER WIZARD for USB Port, ----> Printer Guide.
Windows 95 / 98 / Me Windows XP
Use BROWSE… to
select the directory that
contains the CAPT.
For example, if you are
using the CD-ROM to
install the CAPT on
Windows 95/98, and
your CD-ROM drive is
drive D:, browse to
D:\English\Win9x, and
click OK.
Use BROWSE…
to select the directory
that contains the
CAPT.
Click FINISH.
If you wish to change
printer name, type a
new name into the text
box.
*If you want to set this
printer as the default
printer, select YES.
Driver file selection
dialog appears.
Click NEXT.
Add Printer Wizard
dialog box
(Printer name)
appears.
*If this printer is
shared with other
computers, check on
SHARED option.
Click NEXT.
You can also modify
this setting after
installation, using
Sharing tab from the
Printer Properties.
Click NEXT.
If you wish to change
printer name, type a
new name into the text
box.
*If you want to set this
printer as the default
printer, select YES.
Click NEXT.
Click YES if you
want to print a
test page, or NO
if you do not
want to print a
test page.
If you opted to print a test page, the test page will be
printed after the installation is complete. If the test page
printed correctly, click YES.
When installation is complete, the following dialog box
appears. Click OK.
Make sure the computer is turned off.
Make sure the power cord of the machine is plugged into the power outlet and the machine
is connected to your computer using parallel cable.
Turn on the computer. Start up Windows XP. PLUG and PLAY will activate and the FOUND
NEW HARDWARE WIZARD dialog box appears. Click CANCEL. For installations, using
PLUG and PLAY function of your computer, -----> Printer Guide.
Set the CD-ROM into the CD-ROM drive of your computer.
Click
HAVE DISK…in the
MANUFACTURERS/
PRINTERS dialog box.
THE INSTALL FROM
DISK dialog box
appears. USB CABLE — Windows 98 / Me / 2000 / XP
Click Canon
PC1200/iC D700
INSTALL button.
ADD PRINTER
WIZARD dialog box
appears.
Select LOCAL
PRINTER, then click
NEXT.
Add Printer
Wizard dialog box
(Manufacturers/printers)
selection appears.
Driver file selection
dialog appears.
Click NEXT.
Printer port selection
dialog box appears.
Click
HAVE DISK… in the
MANUFACTURERS/
PRINTERS dialog box.
THE INSTALL FROM
DISK dialog box
appears.
When the installation
is complete, the
following dialog box
appears.
To close the dialog
box, click OK.
Select LOCAL
PRINTER ATTACHED
TO THIS COMPUTER,
then click NEXT.
Printer port selection
dialog box appears.
AUTOMATICALLY
DETECT AND
INSTALL MY PLUG
AND PLAY PRINTER
is not recommended.
Click Canon
PC1200/iC D700
INSTALL button.
ADD PRINTER
WIZARD dialog box
appears. Click NEXT.
Check on the use
following port: Select
the printer port, the
machine is connected
to (usually LPT1:
Recommended printer
port), then click NEXT.
Add Printer Wizard
dialog box
(Manufacturers/
Printers selection)
appears.
Click FINISH.
INSTALL PRINTER DRIVER (CAPT)
6
SET FAX RECEIVE MODE (D780)
5
A
B
C
D
A
B
C
D
E F
G H
IJ
EF
G H
L M
N O
P
IJ
K
K
L
M
L
Machine
Telephone
line
Telephone or
answering machine
L
Machine
Telephone
line
Telephone
Answering
machine
LINE TEL.
L
Machine
Telephone
line
Telephone
Modem
LINE TEL.
Computer
Serial
Connector
L
Machine
Telephone
Computer
LINE TEL.
L
of the line to the telephone
jack on your wall.
1. Connect the supplied telephone line to the
Jack, then connect the other end of the line
to the telephone jack on your wall.
2. When you require to send and
receive both faxes and voice calls,
connect the line from the telephone
or answering machine to the Jack.
CONNECTING THE TELEPHONE LINE
AND AN EXTERNAL DEVICE
(Only for the D780 model)
The machine has two jacks on the left side for
the following connections:
: Telephone Line
: External device, such as telephone or answering machine.
CONNECT EXTERNAL
DEVICES AS FOLLOWS:
L
L
NOTE: For Windows 2000/NT 4.0 - see Printer Guide on CD-ROM
A
B
C
D
PARALLEL CABLEPARALLEL CABLE
For example, if your
CD-ROM drive is drive
D:, browse to
D:/English/WinXP,
click OPEN.
Make sure the folder is
selected in the COPY
MANUFACTURER’S
FILES FROM box,
then click OK.
*If there already are other printer drivers installed on your computer,
this option may not be displayed.
*If there already are other printer drivers installed on your computer,
this option may not be displayed.
1
2
1
2
3
*Depending on your computer settings, this option may not be displayed.
CRT_IMAGECLASSD700_EN 26/09/2003 17:11PM Page 2

Navigation menu