Canon Pixma Mg3222 Setup Guide

Canon-Pixma-Mg3220-Inkjet-Multifunction-Printer-6223B002-Users-Manual-240051 canon-pixma-mg3220-inkjet-multifunction-printer-6223b002-users-manual-240051

Canon-Pixma-Mg3220-Quick-Start-Guide canon-pixma-mg3220-quick-start-guide

Manual MG3200_NonPC_EN Canon Pixma MG3220 Setup Manual | Manual Device

6223B002 to the manual a5c5b95f-65f8-4f1e-adda-ff266bf1bd2e

: Canon Canon-Pixma-Mg3222-Setup-Guide-589270 canon-pixma-mg3222-setup-guide-589270 canon pdf

Open the PDF directly: View PDF .
Page Count: 5

PIXMA MG3200

Setup Guide

© CANON INC. 2012

series

Setup Guide

This guide provides information for setting up a network connection for the printer.

Network Connection

Wireless Connection

Preparation for Connection

Printer Setup

Connection Using WPS

Troubleshooting

Network Connection

Wireless Connection

a Preparation for Connection

Before Starting Wireless Connection Setup

1. Make sure that the printer is turned on.

If the power is on, the LED (Light Emitting Diode) is lit as shown in the illustration below.

Notes on Wireless Connection

Make sure that the computer is connected to the access point (A) (or wireless network router) you want to connect your

printer to.

The confi guration, router functions, setup procedures and security settings of the network device vary depending on your

system environment. For details, refer to the manual of your network device or contact its manufacturer.

Check if your device supports IEEE802.11n, 802.11g or 802.11b.

If your device is set to the "IEEE802.11 n only" mode, WEP or TKIP cannot be used as a security protocol. Change the

security protocol for your device to something other than WEP and TKIP or change the setting to something other than

"IEEE802.11 n only."

For offi ce use, consult your network administrator.

Take added care when connecting to a network that is not protected with security measures, as there is a risk of disclosing

data such as your personal information to a third party.

An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without an

access point, is not supported. Be sure to prepare an access point.

b Printer Setup

1. Press and hold the Maintenance button (A) on the printer (for about 5 seconds).

2. Make sure that the LED fl ashes as shown in the illustration below.

•

•

•

•

•

•

•

c Connection Using WPS

1. Press the Fit to Page button (A).

2. Make sure that the LED fl ashes as shown in the illustration above, then press and hold the WPS

button on the access point within 2 minutes.

For details on pressing the WPS button, refer to the access point manual.

The (blue) Wi-Fi lamp on the printer fl ashes while searching for or connecting to the access point.

3. When wireless connection is complete, the LED lights up for about 3 seconds, then changes to "1" as

shown in the left illustration below. Make sure that the (blue) Wi-Fi lamp on the printer is lit.

The network connection setup is now complete.

Troubleshooting

WPS

E > 2 > 1

The error appears when wireless connection setup was not completed within 2 minutes after pressing the WPS

button.

Is the network device (router, etc.) turned on? If the network device is already turned on, turn it off, then turn it back

on.

E > 2 > 3

The screen appears when multiple access points are detected. Wait for a while, then confi gure WPS settings again.

Press the WPS button on only one access point.

E > 2 > 4

The screen appears when an error occurs.

Check the access point settings, then confi gure WPS settings again.

For details on how to check the settings of the access point, refer to the manual supplied with the access point or

contact its manufacturer.

To confi gure WPS settings again

1. Press the Color button (A).

2. Press and hold the Maintenance button on the printer (for about 5 seconds).

3. Make sure that the LED fl ashes as shown in the illustration above.



•





