Canon FM48944 Wireless LAN Module User Manual Instllation manual

Download:
Mirror Download [FCC.gov]
Document ID	1394420
Application ID	bYOdwfy1FvoRy2yHdhkZYA==
Document Description	Instllation manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	43.97kB (549596 bits)
Date Submitted	2010-12-21 00:00:00
Date Available	2011-06-19 00:00:00
Creation Date	2010-12-21 16:31:09
Producing Software	Acrobat Distiller 9.3.3 (Windows)
Document Lastmod	2010-12-21 16:31:09
Document Title	Microsoft Word - wirelesslan_設置手順書.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	19801

1-1
Wireless LAN Board-C1
Check of bundled parts
Installation procedure
[1] Wireless board x 1
[2] Flat cable x 1
[3] Screw (TP;M3x6)  1
If bundled parts are used;
If the parts bundled with this product are used, the symbol indicating the use of
bundled parts is illustrated.
Bundled
parts
In this procedure manual, the frequent operations are illustrated with symbols.
Screw
Connector
Binding wire
Attach
Claw
Detach
Attach
Detach
Attach
Detach
Push
Plug in
Attach
Detach
Switch ON
Check Visual check Noise check
1-1
1-2
Check of main power OFF
Check that the main power switch of the main body is OFF.
1) Turn OFF the main power switch of the main body.
2) Check that the indication lamps on the operation panel and the main power
lamp are out, and pull out the power plug.
Installation procedure
1) Press cassette [1].
2) Press button [2]. Open cartridge door unit [3].
Schematic diagram of attachment
3) Open ADF unit and reader unit [1].
1-2
1-3
4) Remove claw [1] and arm cover [2].
5) Disconnect arm [1] and push it back.
6) Shift the left side of main body [1] from the workbench by about 10 cm.
7) Open ADF unit and reader unit [1]. Reset claw [2].
1-3
1-4
8) Open ADF unit and reader unit [1]. While applying stress to left cover [2] in
the arrow direction, reset claw [3].
9) Reset two bottom claws [2] with left cover [1] opened in the arrow
direction.
10) Open ADF unit and reader unit [1].
Memo
Remove the claw with right cover edge [2] reset from four rear cover hooks [1].
Reset claw [3].
Memo
Reset claw [3] while holding left cover [2].
1-4
1-5
11) Open ADF unit and reader unit [1].
Remove boss [2] from left cover [3].
14) Remove connector [1] from the counter board.
 Wire saddle [2]
12) Remove left cover [3].
Memo
For attachment, attach left cover [1] aligning with four protrusions [2] on the left
bottom cover.
15) Remove controller cover [1].
 Six screws [2] (Removed screws are used in step 19).)
 Hook [3]
13) After removing the left cover, put the main body at the center of the
workbench.
1-5
1-6
16) Attach Flat cable [1] on the main controller board [2].
CAUTION:
・Insert the Flat Cable face up.
17) Attach Wireless board [1].
・Hook [2]
・Screw [3] (TP;M3×6)
18) Attach Flat cable [1] on the W-LAN board [2].
19) Put all covers back.
・Control cover
・Left cover
1-6
1-7
Note
■Put following sentences outside of the host device if the FCC ID on the module cannot be seen from exterior.
・“Contains Transmitter Module FCC ID: AZDFM48944” or “Contains FCC ID: AZDFM48944”
・“Contains Transmitter Module IC: 498D-FM48944” or “Contains IC: 498D-FM48944”
■User’s manual of the host device should contain sentences listed below.
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the
radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with the Canadian ICES-003 Class B limits.
1-7

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : 19801
Create Date                     : 2010:12:21 16:31:09+09:00
Modify Date                     : 2010:12:21 16:31:09+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.3.3 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - wirelesslan_設置手順書.doc
Creator                         : 19801
Document ID                     : uuid:194b57fc-f833-4905-b15d-067e192c545f
Instance ID                     : uuid:29b8b584-1811-4c82-83f1-4219097bc509
Page Count                      : 7

EXIF Metadata provided by EXIF.tools