Capital Prospect G6T3 Remote Control Transmitter User Manual
Capital Prospect Ltd Remote Control Transmitter Users Manual
Users Manual
3-Button Garage Door
Remote Control Model G6T3
ln this package, you will find a Skylink' garage door transmitter with 3V
lithium battery, a mounting bracket, a visor clip and a double sided tape.
E
lsatteryinsioel A lt-",:l:l"r visorcrio Double
Sided Tape
There are three buttons on transmitter G6T3, each button can be
programed to control Skylink garage door receiver Smad ButtonrM GB-318
or GB-318-3 or Skylink garage door opener directly.
Follow one or more instructions below in Section 2 to program transmitter
G6T3 to the recetver or receivers you want to control.
You need to do the programming in order to add the transmitter - remote
control to a receiver.
Refer to the receiver Smart Buttonru GB-318 useds instruction to set up the unit.
Smart ButtonrM GB-318 can learn up to 10 remote controls.
To program the transmitter to the receiver, follow the instructions below:
1. Press the learn button on the side of the Smart ButtonrMGB-319.
2. Once the learn button ts pressed, the LED will
llash quickly. Release the learn button.
3. Within 30 seconds, press any one of the 3 buttons
on the transmitter that you want to program to the
receiver.
Once the remote control is programmed, the LED
will flash slowly, in the same way as it flashes
in standby mode.
You may now operate the garage door opener
with this new remote control.
To program this transmittei.to conirol another
receiver. repeat process (1) to (+) to program
another button on the remote control.
You need to do the programming in order to add the transmitter to a
Skylink@ Garage Door Opener.
Skylink@ Garage Door Opener can learn up to 16 remote controls.
To program the transmttter to the Garage Door Receiver, follow the
instructions below:
1. Press the LEARN/SET button once on the garage door opener.
2. Once the LEARN/SET buttton is pressed, the LEARN LED will ftash.
You may release the LEARN/SET button.
3. Within 30 seconds, press any one of the 3 buttons on the transmitter
that you want to program to the receiver.
4. Once the transmitter is programmed, the LEARN LED will turn off.
5. You may now operate the garage door opener with this new transmitter.
6. To program a transmitter to control another garage door opener,
repeat process (1)to (a) to program another button on the transmitter.
Smart ButtonrM
G8.318
To program the transmitter to a Skylink Garage Door
Receiver Smart Buttonru GB-318-3 (3 doors) , please
follow the user's instruction for the model GB-g1g-3.
To program the transmitter to the Skylinko le senes Garage Door Opener,
please follow the user's instruction from the Garage Door Opener.
Q: What can I do if the door opener does not react after I press the bufton on
the transmitter ?
A: - Ensure when the button on the transmitter is pressed, the red light on the
transmitter comes on. Otherwise, check if the battery is inserted properly.
- Make sure the correct button on the transmitter is pressed.
- Ensure the wires that were previously connected to the wall mounted
door control are nol loose.
- Ensure the transmitter has been programmed to the receiver. Refer
to section 2 for how to program a transmitter to the recejver.
3 Volt lithium battery (CR 2032) (inctuded).
It is time to change the battery when the red LED on the transrnitter does
not turn on when either button is pressed.
lf you would like to
- find out the up-to-date specifjcations
- know more about leatures and applications
- download documents, i.e. user's instructions
- order Skylink products
or iJ you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call ourtoll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST
Fax (800) 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6y 1J3
Email:support@skylinkhome.com
http:i/www.skylinkhome.com
P/N.101z,&2
Patent Pending
This devicecomplies with Part 15 ofthe Fcc Rules. operation is subjectto thefollowing hryocondttions:
(1 ) Thls device may not cause harmfur interference, and (2) Thrs device must accept any interference
received, including interference that maycause undesiredoperation.
WARNING;
changes ormodifrcationsto this unit not expressryapproved bythe party responsibre forcompriance courd
void the user's authorilyto operatethe equ pment.
NOTE:
Thisequipment has beentested and foundto complywiththe rimitsforacrass Bdigitarcrevice, pursuant
to Pad 1 5 01 the Fcc Rures These rimits are designed to provide reasonabre protection against harmfur
rnterference in a residential installatlon. This equipment generates, uses and can radiate adio frequency
energy and, if not installed and used in accordance with the instructions, maycause harmful interference
to radio communications
However, there is no guarantee that interference will not mur in a particular installation. lf this equipmentdcs
cause harmful interferenceto radio orterevision rrception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference byone or more or the foilowing merures:
- Reorient or relocate the receiving antenna.
- lncrease the separaUon behryeen the equipment and receiver.
- Connect the equipment into arl outlet on a circuit different from that to which the receiver ts connected.
- Consult the dealer or an experienced radio/Tvtechnician for help.
lf, within one year from date of purchase, this product shourd become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
Learn Button
o o d lfif, I[!