Capital Prospect G6V Remote Control Transmitter (318MHz Tx) User Manual D G6 MG6Vnew p65

Download:
Mirror Download [FCC.gov]
Document ID	828722
Application ID	hrW4hYRdV7/JAzbm0u6B3Q==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.22kB (40279 bits)
Date Submitted	2007-08-14 00:00:00
Date Available	2007-08-14 00:00:00
Creation Date	2007-06-21 09:40:30
Producing Software	Acrobat PDFWriter 5.0 for Windows NT
Document Lastmod	0000-00-00 00:00:00
Document Title	D:\G6\MG6Vnew.p65
Document Creator	Adobe PageMaker 6.5
Document Author:	Ida

Universal Visor Transmitter
Model G6V
1. INTRODUCTION
5. BATTERY
Congratulations on your purchase of the Skylink® Universal Visor Transmitter Model G6V. The Model G6V works with the Skylink Smart ButtonTM.
In this package, you will find a visor remote with 12V battery.
Visor clip
12 volt alkaline battery (size 23A)
included.
Universal
Visor Transmitter
(Battery included)
6. ADDITIONAL TRANSMITTER
2. PROGRAM A VISOR REMOTE TO THE GTR SMART BUTTONTM
Refer to the section in the Skylink® model GTR to install the Smart Button TM
and follow the instructions below to program the transmitter.
1. With the GTR Smart ButtonTM connected on your
existing wall button. The red light on the Smart
ButtonTM should flash after plugging in the power.
If the red light on the Smart ButtonTM is flashing
slowly, that indicates it is in standby mode.
2. Press the learn button on the side of the GTR.
3. Once the learn button is pressed, the red LED
will flash quickly. You may release the learn
button.
4. Press the button on the transmitter you would
like to program.
5. Once the transmitter is programmed, the red
LED will flash slowly, in the same way as it
flashes in standby mode.
6. You can now operate the garage door opener
with this new remote control.
You can add up to 15 additional transmitters to control the
same receiver. Skylink® offers Keychain Transmitters and
Keypad Transmitters to work with your receiver. For
more information, please visit our website at
www.skylinkhome.com or contact us.
7. WARNING
DO NOT let children use the garage door transmitter without adult supervision.
Children can injure themselves or others by the garage door.
8. FCC
Learn Button
The Garage Door Remote Control is approved by the FCC and it complies with
Part 15 of the FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible of compliance could void the user’s authority to operate the equipment.
3. TROUBLE SHOOTING
9. WARRANTY
Q: Door opener does not react after pressing the button on the transmitter?
A: - Ensure the button on the transmitter is pressed, the red light on the
transmitter comes on. Otherwise, check if the battery is inserted
properly.
- Ensure the wires that are previous connected to the wall mounted
door control are not loose.
- Ensure the remote control has been programmed to the Smart
ButtonTM. Refer to section 2 for how to program a transmitter to the
receiver.
4. REMOVE THE REMOTE CONTROL FROM THE SMART BUTTONTM
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
10. CUSTOMER SERVICE
If you would like to order Skylink’s product or have difficulty getting your Skylink
remote control to work, please :
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
You can delete the remote control(s) from the Smart ButtonTM, first delete
all the remote controls, then learn the ones you would like to keep.
1. Press and hold the learn button for approx 10 seconds on the Smart
ButtonTM .
2. The LED will flash rapidly after 10 seconds to indicate all the programmed remote controls have been erased. You may now release
the learn button.
3. You have erased all the remote controls in the Smart ButtonTM .
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101Z487
US Patent. D377458
® are registered trademarks of their respective corporations
©2007 SKYLINK GROUP

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 1
Creator                         : Adobe PageMaker 6.5
Create Date                     : 2007:06:21 09:40:30
Title                           : D:\G6\MG6Vnew.p65
Author                          : Ida
Producer                        : Acrobat PDFWriter 5.0 for Windows NT

EXIF Metadata provided by EXIF.tools