Capital Prospect GG318 Remote Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3027517
Application ID	cPjSKL8mMMrRBQTM+FvVPA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.62kB (407700 bits)
Date Submitted	2016-06-14 00:00:00
Date Available	2016-06-14 00:00:00
Creation Date	2016-05-05 14:44:11
Producing Software	福昕PDF打印机 版本 7.2.0.0424
Document Lastmod	2016-05-26 11:59:54
Document Title	User manual

3-Button Remote
MODEL: GG-318
Preliminary Copy
1. INTRODUCTION
Thank you for your purchase of Skylink® remote transmitter,
Model GG-318.
The following items are included in this package:
- One of GG-318 Remote
- Lithium Battery CR-2032 (Installed)
- Mounting accessories
Follow one or more instructions below to program transmitter GG-318 to the Skylink® receiver
or Skylink® garage door opener you want to control.
2. PROGRAMMING
2a. PROGRAMMING A REMOTE TRANSMITTER TO THE SKYLINK® GARAGE DOOR
OPENER ATOMS SERIES
1. Connect the opener to an approved power source.
The dot in the LED display stays on.
2. Press the [Set] button for one second, and release the
3. Within 30 seconds, press any button on the remote
that you would like to program to the opener.
Note:
[ ] = Button 1, [
..
] = Button 2, [
] = Button 3
4. Once the button on the remote is programmed. The
LED segment will off and emits one beep indicating
the programming successfully
Button 1
2b. PROGRAMMING A REMOTE TRANSMITTER TO THE SKYLINK® RECEIVER
GB-318
Refer to the receiver Smart ButtonTM GBup the unit.
1. Press the learn button on the side of the Smart ButtonTM GB-318.
2. Once the learn button is pressed, the LED will flash quickly. Release
the learn button.
3. Within 30 seconds, press any one of the 3 buttons on the transmitter
that you want to program to the receiver.
4. Once the remote control is programmed, the LED will flash slowly, in
the same way as it flashes in standby mode.
5. You may now operate the garage door opener with this new remote
control.
6. To program this transmitter to control another receiver, repeat
process (1) to (4) to program another button on the remote transmitter.
3. OPERATION
Press the programmed button to open/close the garage door or receiver.
4. BATTERY REPLACEMENT
The remote come with a 3 Volt lithium battery (CR 2032) installed. It is time to change the
battery when the red LED on the transmitter does not turn on when either button is pressed.
To replace the battery:
1.
2.
3.
4.
Undo the screw on the back of the remote.
Pry out the back cover from the remote
Take out the old battery.
Place the new battery in position. Be sure the
polarity is correct.
5. Close the back cover with the screw.
Battery Disposal - Dispose used battery according to local regulation.
5.WARNING
This device complies with Part 15 of the FCC rules.
is subject
the following two
conditions:
Rules Operation
and Industry
Canadatolicence-exempt
RSS
1)
this deviceOperation
may not cause
harmful
interference,
and
standard(s).
is subject
to the
following two
conditions: (1) this device may not cause harmful
2)
this deviceand
must(2)accept
any interference
includingreceived,
interference
that may
cause undesired
interference,
this device
must acceptreceived,
any interference
including
interference
that may
operation.
cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void
your authority to operate the equipment.
This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
Cet appareil est conforme aux CNR exempts de licence d'Industrie Canada. Le fonctionnement est soumis aux
deux conditions suivantes:
(1) Ce dispositif ne peut causer des interférences; et
(2) Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement de l'appareil.
6. WARRANTY
If, within one year from date of purchase, this product should become defective (except battery),
due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of
purchase and a Return Authorization are required.
7. CUSTOMER SERVICE
If you would like to
- find out the up-to-date specifications
- know more about features and applications
- download documents, i.e. user’s instructions
- order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST. Fax (800) 2861320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
©2016 SKYLINK GROUP

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
XMP Toolkit                     : 3.1-701
Format                          : application/pdf
Creator                         : 
Description                     : 
Title                           : 
Create Date                     : 2016:05:05 14:44:11+08:00
Creator Tool                    : 
Modify Date                     : 2016:05:26 11:59:54+08:00
Metadata Date                   : 2016:05:26 11:59:54+08:00
Keywords                        : 
Producer                        : 福昕PDF打印机 版本 7.2.0.0424
Document ID                     : uuid:7da3332a-22a2-4a4c-9202-1119469db09c
Instance ID                     : uuid:3de5fc2f-e2fc-4a4f-a937-1e3f810e1634
Page Count                      : 3
Subject                         : 
Author                          : 

EXIF Metadata provided by EXIF.tools