Capital Prospect MD318 LIGHTING REMOTE CONTROL User Manual mMD318

Download:
Mirror Download [FCC.gov]
Document ID	1361887
Application ID	R0jw33oygOlvdcKgooBnbA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.26kB (190782 bits)
Date Submitted	2010-10-18 00:00:00
Date Available	2010-10-18 00:00:00
Creation Date	2010-07-17 23:16:05
Producing Software	Corel PDF Engine Version 9.337
Document Lastmod	2010-07-17 23:16:05
Document Title	mMD318.cdr
Document Creator	CorelDRAW Version 9.337
Document Author:	Joe

Dimmable Receiver Module
Model MD-318
1. INTRODUCTION
3. PROGRAMMING TRANSMITTERS
Thank you for your purchase of a SkylinkHomeTM lighting receiver,
Dimmable Receiver Module Model MD-318. This Dimmable Receiver
Module allows you to wirelessly turn on and off, dim and brighten different
lighting fixtures with the SkylinkHomeTM lighting transmitters.
In order to operate the Dimmable Receiver Module remotely with a transmitter, it must be programmed to the Dimmable Receiver Module. Each
Dimmable Receiver Module can be operated by up to 16 different transmitters (or 16 different command signals).
The Dimmable Receiver Module MD-318 can communicate with up to
8 transmitters, so user has the option to add more transmitters to the
system, such as more remote controls, or motion sensors etc.
To program a transmitter into the Dimmable Receiver Module, follow the
instructions below.
All wireless signal communications within the SkylinkHomeTM lighting
system are based on rolling code technology to ensure highest security
is used.
The following items are included in this package:
- Dimmable Receiver Module
- Screws and Accessories
Dimmable Receiver
Module
Screws and Accessories
CAUTION
Installation is required and enclosed instructions must be followed carefully
to all steps and notes. If you are uncertain or uncomfortable performing this
installation, please consult a qualified electrician. This manual should also
be retained for future reference.
2. INSTALLATION
button
Note: To program other transmitters/sensors (besides TC transmitter),
please refer to the instructions of the transmitters/sensors.
You may follow the same instructions to program additional transmitters
or sensors to operate the Dimmable Receiver Module.
4. OPERATING MODES
1. Turn off power to the circuit at the circuit breaker of the lighting fixture
that you plan on installing the Dimmable Receiver Module to. Remove
the lighting fixture so the Live and Neutral wires are exposed.
WARNING:
Failure to turn off power at the circuit breaker can result in electrical
shock causing severe or fatal injury.
Note: Lighting Load
The Dimmable Receiver Module is designed to operate maximum load of
300W at 120VAC. Do not connect loading that exceeds this maximum
rating.
2. Follow the diagrams below to install the Dimmable Receiver Module
with the 3 wires: Neutral, Live and Load. Use the provided screws to
secure the Dimmable Receiver Module.
3. After all the wires are connected, ensure that all of the wire connectors
are attached securely and there should be no exposed copper wiring.
Straighten the antenna.
After Installation
Before Installation
1. The Dimmable Receiver Module should be power off
initially. This can be done by switching off the wall
switch or circuit breaker of the lighting fixture.
2. Power on the Dimmable Receiver Module by switching
on the wall switch or circuit breaker. You will hear
beeping from the Dimmable Receiver Module and the
light connected to the module should be on. The
beeping indicates the Dimmable Receiver Module
is now in programming mode and it will stay in this “PROG” switch
mode for 20 seconds.
3. Press the PROG button on the back of the transmitter
with a sharp object.
4. Press the button on the transmitter that you would
like to program into the Dimmable Receiver Module.
5. Once the transmitter is programmed, the light will
be off, indicating you have successfully programmed
the transmitter to the Dimmable Receiver Module.
6. You may operate the light with the programmed
Press the
transmitter.
desired
The Dimmable Receiver Module can control the light in 2 different
operating modes.
1) On / Off Mode - Allows operating the light either on and off, without
dimming function.
2) Dimming Mode - Allows operating the light in on, off and dimming
(dim / brighten) modes. Light must be either incandescent light and
designated dimming compact fluorescent light.
The factory default operating mode is on/off mode. However, if your
light is dimmable, you may change the operating mode to Dimming
Mode. To change the operating modes, please follow the instructions
below.
1. Turn on the light by activating the programmed transmitter.
2. Press and hold onto a button on the transmitter that is programmed to
the module for 10 seconds.
3. The light will flash. If it flashes once, that means it is in On / Off Mode.
If the light flashes twice, that means it is in Dimming Mode.
4. Repeating step 3 above will toggle the setting between On / Off Mode
and Dimming Mode.
5. ON / OFF OPERATION
TM
Live
(Usually
Black)
(White)
Neutral
(Usually
White)
(Red)
(Black)
Live
(Usually Black)
Neutral
(Usually White)
Load
4. Secure the MD-318 to a flat surface by 2 screws or you may place it
inside the lighting fixture. Install the lighting fixture back to the original
configuration.
5. Turn the circuit breaker back on and turn on the wall switch that is
used to operate this lighting fixture.
6. The light will be on and you should hear a single beep. The Dimmable
Receiver Module is installed properly and you can begin programming
transmitters to the Dimmable Receiver Module.
The MD-318 Dimmable Receiver Module allows on / off operation, when
the programmed button is activate, it will transmit a signal to toggle its
current status. For example, if a signal is received when the light is off,
that signal will turn on the light.
Note:
If the Dimmable Receiver Module is
installed on a ceiling lighting fixture,
you can use the transmitter to
operate the light remotely only if
the wall switch is in the ON position.
If the wall switch is off, no power
is provided to the Dimmable Receiver
Module and therefore, it cannot
operate the light.
In case the transmitter is misplaced,
you can still operate the lighting
fixture with the wall switch normally.
OFF
Remote
Works
ON
Remote Does
Not Work
5. ON / OFF OPERATION (CONT)
Note:
When used with Compact Fluorescent Light, if there is flickering when you
switch off the light, it is recommended you replace a different Compact
Fluorescent Light with higher quality.
On / Off Operation - Original Wall Switch
8. ZONE OPERATION (CONT)
Pressing [Zone On] then [1] will turn on all lights in zone 1.
Pressing [Zone Off] then [3] will turn off all lights in zone 3.
Zone Operation Brightness Control
You can also change the brightness of all the lights in that zone, if the
receiver modules and lights connected are dimmable.
Power On - Light On
There is a function "Power On - Light On" built-in to the receiver module.
This means when the power supply to the receiver module change from
off to on, this will turn the light on. This function allows you to operate the
light with original wall switch.
When the wall switch is in the off position, switching it on will turn on the
light. Once the switch is on, you may use the remote control to operate
the light.
If the wall switch is switched from on to off, the light will be off. At the
same time, the remote control cannot operate the light cause there is no
power supplied to the receiver module.
In case you do not want to operate the light with the original wall switch,
you can disable this Power On - Light On feature and use only remote
control to operate the light. One incident that the light may be turned on
by accident is after a power failure. If you leave the wall switch on, but
turn off the light with a remote control. When power comes back on, the
light will be on. Therefore, there is an option not to turn the lights on when
power is supplied to the receiver module. The way to disable this feature
is to re-program a transmitter (button) that is already programmed to the
receiver module (i.e. program a transmitter twice). This will disable this
feature. You may re-program it again to toggle the setting between
enabling and disabling this feature.
If the Power On - Light On feature is disabled, the light will not be turned
on under most circumstances, i.e. power comes back up after power
failure, or manually turning on the wall switch. However, you can still turn
on the light by the wall switch with a specific power up sequence, that is
to turn on the wall switch twice within 2 seconds. So in case the remote
control is lost, the light can still be turned on.
6. BRIGHTNESS CONTROL OPERATION
Besides turning on and off the light, you may also control the brightness
of the light if the light bulb is dimmable, i.e. either incandescent light and
designated dimming compact fluorescent light.
To change the brightness, first turn on the light.
Press and hold the programmed button on the transmitter will change its
brightness. Hold onto the button until the desired brightness is reached,
then release the button.
Press and hold the same button again on the transmitter to change the
brightness again in the opposite way (i.e. Dim to brighten or brighten to
dim), until the desired brightness is reached, then release the button.
7. ZONE OPERATION
Zone Operation On / Off (with the TC Series Deluxe Transmitter)
A Zone Command allows you to operate multiple lights at the same time
in the same zone. You may turn On or Off a zone.
A zone command must first be programmed to the Dimmable Receiver
Module. Follow the programming instructions in Section 3 of the manual
and program the zone command under On / Off Mode. For example, if
you would like to assign the Dimmable Receiver Module to be one of the
devices in zone 1, you should press [Zone On] and [1] during step 5B
under pro-gramming instruction Section 3. So the Zone 1 signal is
programmed to the Dimmable Receiver Module.
[Zone On] represents increase in brightness level, i.e. Brightening
[Zone Off] represents decrease in brightness level, i.e. Dimming
Press [Zone On] then hold [1] will brighten all lights in zone 1, release
the button at the desired brightness level or it will stop until they are at
the maximum brightness.
Press [Zone Off] then hold [1] will dim all lights in zone 1, release the
button at the desired brightness level or it will stop until they are at the
minimum brightness.
9. ERASING TC TRANSMITTERS FROM THE
DIMMABLE RECEIVER MODULE
You may erase a TC transmitter from the Dimmable Receiver Module, but
you cannot erase a specific device, you must erase all the wireless
devices, then program the ones you want to keep. Follow the instructions
below to erase programmed TC transmitters.
1. Power off the lighting receiver. (Switch off the wall switch)
2. Press the PROG button on the back of the TC transmitter.
3. Press and hold the programmed button on the TC transmitter for at
least 2 seconds. Do not release this button until step 5.
4. Power up the lighting receiver (Switch off the wall switch), you will hear
beeping and the light will be on.
5. You may release the button on the transmitter.
6. When the button is release, the light attached to the Dimmable Receiver
Module should be off, indicating you have successfully erased all the
devices from the lighting receiver.
To erase other transmitters or sensors, please refer to the instructions of
the transmitters / sensors.
10. TECHNICAL SPECIFICATIONS
Input Voltage: 120VAC, 60Hz
Maximum Load: 300W at 120AVC
Operating Frequency: 318MHz
Wiring: Neutral, Live, Load (18 AWG)
11. FCC
The Remote Control is approved by the FCC and it complies with Part 15 of the
FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
of compliance could void the user’s authority to operate the equipment.
12. CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work
or download latest information and user manual, please :
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
13. ACCESSORIES
TM
To activate the zone command, simply press “Zone On” or “Zone Off”,
then the zone number.
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101Z699
Patent Pending
©2010 SKYLINK GROUP
The SkylinkHome Lighting System consists of many other devices from
multiple button transmitters, Motion Sensor, various receivers such as
Wall Switch Receiver, Plug-in Receiver with Repeater, Outdoor Receiver,
Dimmer Module etc. Please visit Skylink website at www.skylinkhome.com
for more information.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 2
Create Date                     : 2010:07:17 23:16:05
Modify Date                     : 2010:07:17 23:16:05
Producer                        : Corel PDF Engine Version 9.337
Author                          : Joe
Creator                         : CorelDRAW Version 9.337
Title                           : mMD318.cdr

EXIF Metadata provided by EXIF.tools