Cardo Systems ER06 scala-rider TeamSet Driver User Manual QGTS 029 0566TeamSetQGuide

Cardo Systems, Inc. scala-rider TeamSet Driver QGTS 029 0566TeamSetQGuide

manual

scala-rider TeamSet TMCARDO SYSTEMS INC.
2Driver unit (yellow logo)(with BT and Intercom capabilities)Passenger unit (green logo)(with Intercom capability only)INTRODUCTIONThis Quick Guide will get you startedusing the scala-rider TeamSet. For moredetailed information, including safetyprecautions, please download theUser Manual from our website atwww.cardowireless.com. Beforeusing the scala-rider TeamSet, pleasefamiliarize yourself with the Bluetooth®functionality of your cellular phone.The retail box of the scala-rider TeamSetcontains two headset units: One devicefor the driver and a second device forthe passenger.The driver unit (yellow logo) includes aBluetooth module that connects with aBluetooth phone, and an intercom moduleto communicate with the passenger.The passenger unit (green logo) containsonly an intercom module that allowscommunication with the driver. Thepassenger unit cannot connect to a phone.
COMPONENTSOne headset for the driver and one headset for the passenger.3NOTE: The use of two speakers may be illegal in certainjurisdictions. Please check the local regulations and act accordingly.MicrophoneSliding Plate Left speaker(short cord)Right speaker(long cord)Control ButtonStatus LightSliding PanelVolume UpIntercom ButtonCharging Jack(Here shown withclosed cover tongue)Volume DownTab
IMPORTANTThe scala-rider TeamSet is a water-resistant device, designed for useunder moderate rain or snow conditions. However, the headset is notwaterproof and should not be used under severe weather conditions.The cover tongue protecting the Charging Jack should be kept tightlyclosed at all times to prevent moisture from entering the device.BEFORE USING (CHARGING THE HEADSET)Make sure that both headsets are fully charged for at least 5 hoursbefore initial use.1. Connect the wall charger to the headset’s Charging Jack (locatedbetween the two Volume buttons).2. While charging, the red Status Light illuminates (it may take up to 15seconds until the red Status Light illuminates). When charging iscomplete the Status Light will turn off.GENERAL INSTRUCTIONSAll headset functions are controlled either by:• Pressing the Control or Intercom Button either for a short period of lessthan a second or a long period of over three secondsOr• Short pressing the volume up and volume down buttons.4
TURNING THE DRIVER HEADSET ON FOR THE FIRST TIMEThe driver unit (yellow logo): The driver unit permits two communicationmodes:• Mobile Phone connections with third parties• Intercom connection with the passengerIn order for the headset to work with your cellular phone, they must firstrecognize each other. This process is called “pairing”, and only needsto be performed once for each phone.1. Turn on your phone and make sure its Bluetooth function is activated.2. With the headset turned off, press and hold the Control Button for tenseconds until the red and blue Status Lights begin flashing.3. Search for Bluetooth devices on your phone by following the phone’sinstructions.4. After a few seconds the phone will list the scala-rider TeamSet asa discovered device. Select it and follow your phone’s instructions toaccept the pairing.5. When prompted enter 0000 (four zeros) as your PIN or passkey.6. Your phone will confirm that pairing has succeeded.Note: If pairing is not completed within two minutes the headset willreturn to Standby mode.Your headset can pair with up to eight phones, and will automaticallyconnect to the last phone connected to the headset.5
The Passenger Unit (green logo): This unit is solely intended for intercomconnection with the driver and it cannot initiate or receive a phone call.To turn on the Passenger Unit, press the Control Button until the blueStatus Light illuminates.NOTE: The Driver and Passenger Units are already factory-synchronizedfor Intercom communication with each other, and do not require anysynchronization by you.SYNCHRONIZING INTERCOM BETWEEN THE PASSENGER ANDDRIVER HEADSETSThe two headset units (Driver and Passenger units) are supplied factorysynchronized for Intercom communication with each other. Therefore,you do not need to perform the synchronization between these devices.However, if you have purchased these units separately and not in theTeamSet Retail box, you need to synchronize the devices yourself byproceeding as follows:1. Simultaneously press and hold the Intercom Buttons of both devices forat least 10 seconds while watching the Status Light on the Passenger unit.2. Once the Status Light on the Passenger unit lights steady red, wait threeseconds and then release both Intercom Buttons.3. If successful, the steady red Status light on the Passenger unit will switchto a steady blue light for a few seconds, then begin flashing blue. Yourtwo headsets are now synchronized for Intercom communication.4. If the synchronization has failed, the steady red Status light on thePassenger unit will turn off without switching to steady blue for a fewseconds, and you must repeat the synchronization procedure.6
Back PlateAllen Wrench7ATTACHING THE SCALA-RIDER UNITS TO YOUR HELMETSPerform this procedure for both the driver and passenger helmets.1. Use the enclosed Allen Wrench toloosen the two screws on the BackPlate.2. Slide the Back Plate between theinternal padding and the externalshell of the helmet. (If the externalshell is too thick, use the suppliedplastic Extension Pad by looseningthe screws and fitting the extentionpad between the Back Plate and themain body of the clamp).3. Adjust the clamp’s location so thatthe microphone is located in front ofyour mouth, and then tighten thescrews. Attach the speakers to theVelcro inside your helmet oppositeyour ears (short speaker cord for leftear & long speaker cord for right ear),or use the supplied Velcro pad. INCORRECTNOTE: The microphone must be positioned vertically andnot horizontally.CORRECT
84. Slide the headset downwards alongthe sliding panel until a clicking soundindicates that the headset is lockedin place.REMOVING THE HEADSET FROM THE HELMETYour headset can be removed for charging and storage by pressingyour finger gently against the tab and sliding the headset up with theother hand.We recommend that you store your headset in the enclosed carryingpouch when not in use.Press here toremove
DRIVER’S UNIT FUNCTIONSDESIRED RESULT: REQUIRED ACTION:GENERAL FUNCTIONSTurn on the headset Press the Control Button steadily for at least 6 secondsTurn off the headset Press the Control Button steadily for at least 3 secondsIncrease the volume Short press the Volume Up Button.Decrease the volume Short press the Volume Down Button.PHONE FUNCTIONSAnswer a call Short press the Control Button or speak loudly any wordof your choice.Reject a call Short press the Intercom Button or remain silent for 15 seconds.Terminate a call Long press the Intercom Button. For some mobile phonesyou may need to press the Control Button to end the call.Voice Dial During standby, short press the Control Button and statethe name of the person you wish to call. This feature is supported only by mobile phones that support the VoiceDial feature.Redial During standby, long press the Intercom ButtonEnable/Disable voice Long press the volume up and down buttonscommand feature simultaneously until you hear a beep. The default statusis voice command enabled.9
DRIVER’S UNIT FUNCTIONS (continued)DESIRED RESULT: REQUIRED ACTION:INTERCOM FUNCTIONSStart using the intercom During standby, start speaking loudly to activate theintercomTerminate the operation Stop speaking. The audio connection will be terminatedof intercom within 25 seconds.Conference Call (add During an active phone call, tap the Intercom Button.passenger to an activecall)End Conference Call During a conference call, tap the Intercom Button.(release passengerfrom a conference call)Enable/Disable Voice Long press the volume up and down buttons until youCommand feature hear a beep. The default status is Voice Commandenabled.PASSENGER’S UNIT FUNCTIONSDESIRED RESULT: REQUIRED ACTION:Turn on the headset Press the Control Button steadily for at least 3 secondsTurn off the headset Press the Control Button steadily for at least 3 secondsStart using the intercom During standby, start speaking loudly to activate theintercomTerminate operation Stop speaking. The audio connection will be terminatedof intercom within 25 seconds.Enable/disable During standby, short press the Control Button.Always On Intercom One tone = Always On intercom.Two tones = Voice Controlled (VOX) intercomIncrease intercom volume Short press Volume Up ButtonDecrease intercom volume Short press Volume Down Button10
DRIVER’S UNIT STATUS LIGHTSThe Driver Headset uses the following Status Lights to display its currentstate:Status Light StatusNone Headset is offAlternating Red/blue flashes Pairing mode1 blue flash every 3 seconds Standby – No call is in progress2 blue flashes every 3 seconds Call being initiated or in progress1 red flash every 3 seconds Battery is low2 red flashes every 3 seconds Call being initiated or in progress and batteryis lowSteady red Headset is being chargedPASSENGER’S UNIT STATUS LIGHTSThe Passenger Headset uses the following Status Lights to displayits current state:Status Light StatusNone Headset is offOne blue flash every 3 seconds Headset is onSteady red Headset is being charged11
AUDIO TONESWith the exception of the actions below, all other actions are followedby a single tone to confirm that the headset has accepted the command.Action ToneEnable/Disable Always On One tone = Always On intercomintercom Two tones = Voice Controlled (VOX) intercomIntercom on other side is 2 beeps to alert you that the other side is notnot enabled or off and you availablestart speakingTROUBLESHOOTINGProblem ActionPhone-Related Problems (Driver Unit with Bluetooth Phone)Unsuccessful Bluetooth Pairing 1. If listed, delete scala-rider from your paired device list of your phone.2. Turn off the phone and headset.3. Remove the battery from the phone, then placethe battery back in the phone.4. Repeat the pairing process as described above.I cannot hear stereo sound The two speakers provide only dual mono signals.Can’t answer calls or perform 1. Make sure that the scala-rider headset is turnedvoice dialing by pressing the ON and in standby mode with the blue StatusControl Button Light slowly flashing.2. Verify that the Bluetooth function on your phoneis set to ON.12
3. Verify that the scala-rider headset is the pairedheadset to your phone.4. Reconnect the phone and headset by shortpressing the Control Button on the headset, orconnecting them manually by using yourphone’s menu.5. Check the definitions and settings on your phone.6. Repeat the pairing process as described inTURNING THE DRIVER HEADSET ON FORTHE FIRST TIME, page 5.Cannot terminate calls using Your phone supports only the Bluetooth headsetthe intercom button profile and not the handsfree profile. Therefore you must use the Control button to answer or terminate calls.Can’t answer phone calls 1. Make sure that you speak the word loudly afterusing the Voice Command prompting(VC) feature. 2. Close the helmet visor.3. Make sure that the VC feature is activated (seeDriver’s Unit Functions, page 9)4. The VC feature works well while driving up to70 km/h or 44 mph with a 3/4 helmet and up to120 km/h or 75 mph with a closed full faced helmet. High-end helmets may get better results.I cannot perform redial 1. Make sure that the call list on your phone is not empty.2. The Redial feature works only with mobile phones that also support the Bluetooth handsfree profile. Check whether your phonesupports this profile.13
Battery does not provide at 1. Make sure your scala-rider headset is fullyleast five hours of talk time charged. Charging time is up to 5 hours for anempty battery. When the headset is connectedto the charger and it is fully charged, the red Status Light turns off.2. You may have inadvertently left theAlways-On Intercom on.I’m trying to reject incoming 1. Make sure the VC feature is enabledcalls by remaining silent, but 2. Reject feature works only with mobile phonesthe phone continues to ring. that support Bluetooth hands-free profile. Makesure your mobile phone supports this profile.Red Status Light does not 1. Make sure the Charging Jack is firmly pluggedlight steady when charger into the headset and wait 5 secondsis connected. 2. Disconnect the Charging Jack wait a few seconds and plug it back in.3. When the headset is fully charged the red lightturns off.I hear crackling noises 1. Possibly caused by nearby interference. If youhave a GSM phone and your headset is too close to phone, noises may be heard.2. Headset and mobile phone are more than 30ft. (10 m) apart or there are major obstacles (such as concrete walls) between the headsetand mobile phone.Sound deteriorates when the Some mobile phones emit weaker Bluetoothphone is in my back pocket. signals than others, resulting in reduced sound quality, especially when the phone is close to yourbody. Suggestion: Move the phone to your breast14
pocket or at least to a front pocket on the same side you wear your headset.The party I am speaking to 1. Close helmet cover under high speed conditions.complains about insufficient 2. Make sure the microphone is in front of youraudio quality mouth. The microphone should be positionedvertically as described on page 7.Intercom-Related Problems (driver/passenger)Cannot initiate conversation 1. Try speaking louder.with other party 2. Make sure the microphone is located in the(driver/passenger) correct place as described in this guide3. Make sure that intercom is not disabled in bothdriver and passenger units. (To toggle Intercomoperation, tap the intercom button. You will hear one beep when enabled; two beeps meansthat the intercom is disabled.)I keep hearing the speaker 1. If you drive with an open face helmet at 60even though no-one is km/h (37 mph) or use a closed helmet abovespeaking (audio connection 110km/h (68 mph), the wind noise may activateis not released). the intercom connection between passenger and driver.2. You can disable the intercom by following theinstructions shown above.3. Make sure the microphone is placed at the correct location as described in this guideWhen I receive an incoming This is normal behavior. The driver may choosecall, the intercom disconnects to bring the passenger into a conference call byshort pressing the Intercom Button.15
Federal Communications Commission (FCC) Statement15.21You are cautioned that changes or modifications not expressly approved by the partresponsible for compliance could void the user’s authority to operate the equipment.| NOTICES15.105(b)This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to part 15 of the FCC rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or moreof the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Operation is subject to the following two conditions:1) this device may not cause interference and2) this device must accept any interference, including interference that may causeundesired operation of the device.
FCC RF Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolledenvironment. End users must follow the specific operating instructions for satisfyingRF exposure compliance. This transmitter must not be co-located or operating inconjunction with any other antenna or transmitter.Industry Canada (IC) Statement15.21You are cautioned that changes or modifications not expressly approved by the partresponsible for compliance could void the user’s authority to operate the equipment.15.105(b)This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to part 15 of the IC rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause harmful interference to radioor television reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more of thefollowing measures:¥ Reorient or relocate the receiving antenna.¥ Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different fromthat to which the receiver is connected.¥ Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:1) this device may not cause interference and2) this device must accept any interference, including interference that may causeundesired operation of the device.IC RF Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolledenvironment. End users must follow the specific operating instructions for satisfyingRF exposure compliance. This transmitter must not be co-located or operating inconjunction with any other antenna or transmitter.European CE NoticeThe scala-rider TeamSet Driverô headset (the “Product”) is in conformity with thefollowing essential requirements of Council Directive 1999/5/EC (referred to as R&TTEDirective): Articles 3.1a, 3.1.b and 3.2. The Product is manufactured in accordancewith Annex II of the above directive.Declaration of Conformity (DOC)The scala-rider TeamSet Driverô headset is compliant with and adopts the BluetoothSpecification 2.0 and has successfully passed all interoperability tests that are specifiedin the BluetoothÆ specification.However, interoperability between the device and other Bluetooth- enabled productsis not guaranteed.
WAIVER AND GENERAL RELEASEBy using the scala-rider TeamSet Driver you will waive substantial legal rightsincluding the right to sue. Please read the following carefully before using thedevice. If you do not accept all terms of this agreement, you should immediatelyreturn the product for a full refund. By using the headset you agree to be boundto this agreement and forfeit the right to sue.Using a communication device while riding a motorcycle, scooter, moped, ATV, quad-bike or any other vehicle or equipment, whether on land, water or air (jointly referredto as ìVehicleî) requires your complete and undivided attention. Cardo Systems, Inc.,including its Officers, Directors, Affiliates, Parent Company, Representatives, Agents,Contractors, Sponsors, Employees, Suppliers and Resellers (jointly referred to asthe “Company” or “Cardo”) strongly advises you to take all necessary precautionsand remain alert to the traffic, weather and road conditions if you choose to use thescala-rider TeamSet Driver headset, including all derivative models irrespective ofits commercial name or branding (the “Device”), and stop your Vehicle on the roadsideprior to initiating or receiving calls. Any publications, advertisements, announcementsor similar notes that refer to using the Device while riding a Vehicle are solely intendedto address its technical capabilities and should not be misconstrued as if encouragingusers to operate the Device while actively involved in traffic.By way of purchasing this Device and not returning it for a full refund (seebelow), you are irrevocably releasing, indemnifying from any liability, loss,claim and expense (including attorneys fees) and holding Cardo harmlessfor any bodily injuries, harm or death as well as losses or damages ingoods, to any Vehicles including your own, or to any property or asset thatbelong to you or to third parties, any of which may result from using the
Device under any circumstances or conditions and irrespective of jurisdiction.Cardo will not be responsible for any physical damages, irrespective ofreasons, conditions or circumstances, including malfunctioning of the Device,and all risks associated with operating it rest solely and entirely with theuser of this Device, irrespective of whether the Device is used by the originalpurchaser or any third party.Cardo hereby notifies you that using this Device may also be in contraventionto local, federal, state or national laws or regulations, and that any use ofthe Device is entirely at your sole risk and responsibility.1. You, your heirs, legal representatives, successors or assigns, herebyvoluntarily and forever release, discharge, indemnify and hold harmlessCardo from any and all litigation, claims, debts, demands, actions andliability which may arise, directly or indirectly, from using the Device forany distress, pain, suffering, discomfort, loss, injury, death, damages toor in respect to any person or property however caused, WHETHERARISING FROM THE NEGLIGENCE OR OTHERWISE, and which mayhereafter accrue to you on some future date as a result of said use, tothe fullest extent permitted by law.2. You fully understand and assume the risks in using the Device, includingrisk of negligent acts or omissions by others.3. You confirm that you are physically capable to use the Device and thatyou have no medical conditions or needs that may infringe upon yourabilities to do so in a safe manner. You confirm that you are at leasteighteen (18) years of age and that you have been advised of the risksassociated with the use of the Device. You further confirm that you willnot consume any alcohol that may affect your alertness or any mind-
altering substance, and will not carry, use or consume these substancesbefore or during the use of the Device.4. You fully acknowledge our warnings and understand that: (a) risks and dangersexist in using the Device while in traffic, including but not limited to injury or illness,strains, fractures, partial and/or total paralysis, death or other ailments that couldcause serious disability; (c) these risks and dangers may be caused by the negligenceof the manufacturers or its agents orany third party involved in designing or manufacturing the Device; (d) these risks anddangers may arise from foreseeable or unforeseeable causes. You hereby assumeall risks and dangers and all responsibility for any losses and/or damages, whethercaused in whole or in part by the negligence or other conduct of others, including theCompany.5. You confirm that you have read this release of liability and fully understand itsterms and that you have given up substantial rights by not returning the Device fora full refund (see refund option below).Disclaimer of WarrantyCARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARDTO THE ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIEDWARRANTIES OF MERCHA NTABILITY, FITNESS FOR A PARTICULARPURPOSE, AND NON-INFRINGEMENT. THE DEVICE AND ITS ACCESSORIESARE PROVIDED ìAS ISî AND ìAS AVAILABLEî WITHOUT WARRANTY OF ANYKIND BEYOND THOSE ASSUMED IN THE ENCLOSED MANUAL.
Limitation of LiabilityIN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL, INDIRECT, PUNITIVE,INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGESWHATSOEVER RESULTING FROM THE USE OF THE DEVICE, WHETHER BASED ONBREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OROTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. YOUACKNOWLEDGE AND AGREE THAT THE LIMITATIONS SET FORTH ABOVE AREFUNDAMENTAL ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT BEPROVIDED TO YOU ABSENT SUCH LIMITATIONS. SOME STATE STATUTES MIGHT APPLYREGARDING LIMITATION OF LIABILITY.RETURN FOR FULL REFUNDIF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS, YOUMAY RETURN THIS DEVICE TO CARDO FOR A FULL REFUND, PROVIDED THAT YOU DOSO NO LATER THAN 7 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE(proof of purchase required) AND SUBJECT TO THE WRAPPING BEING INTACT. WHENDOING SO, PLEASE REFER TO THIS SECTION.BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE PERIOD PROVIDED, YOUARE EXPLICITLY IN AGREEMENT WITH THE ABOVE, AND RENOUNCE ALL RIGHTS TOFUTURE CLAIMS AND DEMANDS AGAINST CARDO AS DEFINED ABOVE.
QGTS_027_0566PLEASE NOTE: THE USE OF THIS PRODUCT IS AT YOUR SOLE RISK AND MAY BEILLEGAL IN CERTAIN JURISDICTIONS. ALL WAIVER PROVISIONS CONTAINED IN THECOMPREHENSIVE USER MANUAL APPLY. IF YOU ARE UNWILLING TO ACCEPT ANYOF THE SAID WAIVER CONDITIONS YOU MAY RETURN THE PRODUCT FOR A FULLREFUND ACCORDING TO COMPANY POLICY TERMS.SUPPORTFor additional information visit our website atwww.cardowireless.com, or call us at:Toll-free USA: 1-800 488-0363Europe: +49 89 450-36819Developed and Manufactured by:www.cardowireless.com

Navigation menu