Cardo Systems ER18 Bluetooth headset User Manual SRC System EN

Cardo Systems, Inc. Bluetooth headset SRC System EN

Users Manual(rev1)

USER MANUALPOWERED BYcommunication in motion®
2CONTENTS1. INTRODUCTION ..............................................32. CHARGING THE BATTERY .....................................43. UPDATES AND SETTINGS .....................................44. GETTING STARTED ...........................................54.1 INSTALLATION ................................................54.2 GENERAL FUNCTIONS ........................................64.3 STATUS LIGHTS ...............................................64.4 AUDIO SOURCES AND PRIORITIES ............................64.5 VOICE CONNECT VOX SETTINGS .............................65. INTERCOM ...................................................75.1 INTERCOM COMPATIBILITY ....................................75.2 PAIRING THE INTERCOM CHANNEL ...........................75.3 MAKING INTERCOM CALLS ...................................75.4 RECEIVING INTERCOM CALLS .................................75.5 BUSY SIGNAL .................................................75.6 CLICKTOLINK® INTERCOM CTL ..............................86. PAIRING AND USING A MOBILE PHONE, GPS DEVICE OR MP3 PLAYER .................................................86.1 PAIRING BLUETOOTH CHANNELS 1 AND 2 .....................86.2 RESET PAIRING ................................................96.3 MAKING AND RECEIVING PHONE CALLS ......................96.4 LISTENING TO MUSIC VIA A2DP ...............................97. TROUBLESHOOTING .........................................108. SUPPORT ...................................................109. NOTICES ....................................................10CONTENTS OF RETAIL BOX If you purchased the SRC-System™ DUO, your retail box contains two factory-paired SRC-System™ units and two of each item listed below.SRC-System™1 Micro USB (•) 2 Volume Up (a) 3 Schuberth Button ( )4 Volume Down (a)5 LEDWall charger plug3USB cable4
31. INTRODUCTIONThank you for choosing the SRC-System™ Bluetooth® communication and entertainment system for motorcycle helmets. This manual will help you set up, congure and use the SRC-System™.INTERCOM OPTIONS IN FULL DUPLEX• Bike-to-Bike intercom at a range of up to 500m• Rider-to-Passenger intercom• Click-to-Link® Intercom: For spontaneous connection with other riders nearby who have CTL-enabled devicesMULTIPLE DEVICE CONNECTIVITY• 2 Bluetooth connections for mobile phones / MP3 Players / GPS Navigation devices• Other riders via intercomENTERTAINMENT OPTIONS• Wireless music streaming via devices supporting Bluetooth Stereo A2DP and AVRCP prolesCARDO COMMUNITY®AND CARDO SMARTSET APP* • Customize the settings via your computer or smartphone• Download software upgrades, enhancements and new features*App available on Android and iOS devicesADVANCED TECHNOLOGY➤ AGC (Automatic Gain Control) technology, for the automatic adjustment of volume according to ambient noise and driving speed. You can also control the volume level manually. AGC sensitivity levels can be customized to suit your personal preferences.➤ VOX technology for safe, hands-free operation of key functions. VOX sensitivity levels can be customized to suit your personal preferences.➤ PLC (Packet Loss Concealment) software for real-time compensation of audio losses in challenging environments.➤ Spoken status announcements, so that you always know to whom or to what device you are connected.➤ Volume Per Mode: Volume is set and saved at dierent levels for each audio source.We wish you a great SRC-System™ experience!This is version 1.0 of the User Manual. Please note, that our manual is periodically updated on the Schuberth website to include the very latest features and functions of your new SRC-System™.
42. CHARGING THE BATTERYMake sure that your unit is fully charged for at least 3 hours before initial use. Charging with the wall charger is faster than via a computer USB port.• RED LED ON – Charging • RED LED OFF – Charging completeThe battery level can be checked on the Android app or on iPhones running iOS 5 or later using the Bluetooth headset battery indicator feature. The icon appears automatically once you have paired and connected your SRC-System™ to the phone.IMPORTANT:The SRC-System™ is waterproof and dustproof. However, when in use, the USB silicone cover should be kept tightly closed to prevent moisture from entering the unit.3. UPDATES AND SETTINGSGet the most out of your SRC-System™ by changing the settings and customizing your unit according to your own personal preferences. Software updates are available via the Cardo Community on your PC / Mac*. Settings can be changed either by the Cardo Community or the Cardo SmartSet App on a compatible smartphone.In order to receive full Schuberth service and the latest news, please register your SRC-System™ at www.schuberth.com/register/enCardo CommunitySmartSet AppDownload the latest software upgrade  Set your Hot-Dial number  Change A2DP / Intercom audio priority  Spoken Status Announcements  Change AGC sensitivity for the speakers  Change VOX sensitivity for the microphone  Click-to-Link Enable/Disable  CARDO COMMUNITY WEB PLATFORMVisit http://community.cardosystems.com *Minimum requirement: Windows® XP or later / Mac OS X® 10.6 or later Mac and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.
5Cardo SmartSet AppCARDO SMARTSET APP4. GETTING STARTED4.1 INSTALLATION
64.2 GENERAL FUNCTIONSPower ON Press for 2 seconds3 BLUE ashes with ascending tonePower OFF In Standby, press for 2 seconds 3 RED ashes with descending toneVolume Tap a or a to adjust and set volume of current audio sourceMute / Unmute Tap a and a simultaneouslyEnable / Disable VOX (For Intercom calls only)In standby, press a and a simultaneously for 2 secondsENABLED: Blue ash for 2 secondsDISABLED: Red ash for 2 seconds4.3 STATUS LIGHTSNone SRC-System™ is OFF1 BLUE ash every 3 seconds Standby modeNo active audio sources2 BLUE ashes every 3 secondsActive mode – Call in progress / music or other audio source is ON1 RED ash every 3 seconds Standby mode – Battery is low2 RED ashes every 3 seconds Active mode – Battery is lowSolid RED Charging4.4 AUDIO SOURCES AND PRIORITIESIf two connected audio sources try to play audio simultaneously, your SRC-System™ automatically determines which audio source to play through the speakers based on the priority of the connected devices.Higher Priority 1. Mobile Phone audio or GPS instructions*2. Intercom / Click-to-Link3. A2DP (Stereo Bluetooth) audio* GPS instructions from Smartphone GPS Apps are prioritized like A2DP audioLower PriorityFor example:• Incoming mobile phone calls interrupt ongoing intercom calls• Incoming intercom calls will interrupt ongoing A2DP music• Intercom and Click-to-Link calls have the same priority. So Click-to-Link calls will not interrupt any Intercom call in progress, and vice-versa. A2DP audio priority can be congured higher than Intercom audio priority – see section 3.4.5 VOICE CONNECT VOX SETTINGSYour SRC-System™ oers VOX technology for safe and hands-free operation of some key functions.The VOX can be customized to adjust its sensitivity level. VOX activation for Intercom calls can also be disabled completely.You can choose between ‘High’, ‘Medium’ (default) and ‘Low’ VOX sensitivity.If you experience diculties starting a conversation using VOX, change setting to ‘High’.If VOX keeps starting calls involuntarily, change setting to ‘Low’.
75. INTERCOMThe SRC-System™ allows Bike-to-Bike and Rider-to-Passenger full-duplex intercom communication at a range of up to 500m. To chat via Intercom, you must rst pair your SRC-System™ to the second device. Pairing is a one-time process. Once paired, the two units will automatically recognize each other whenever in range.5.1 INTERCOM COMPATIBILITYYour SRC-System™ is compatible with all Schuberth SRC-Systems™. In addition, it is also compatible with the scala rider line of intercom models. Range is limited to the distance of the device with the shorter range.For details of which scala rider models are compatible, and how to pair and use your SRC-System™ with other models, please visit www.cardosystems.com/SRC.5.2 PAIRING THE INTERCOM CHANNELPairing will replace any existing paired device with the new device. If you have purchased the SRC-System™ DUO, the retail package contains two pre-paired units. If for any reason you have to pair them again, OR if you wish to pair another unit, proceed as follows:1. Check both units are in Standby.2. On the SRC-System™, press for 5 seconds. The LED will begin ashing RED and the unit will now enter intercom pairing mode. 3. Enter intercom pairing mode on the second unit by following the device’s user manual. Both units will now be in intercom pairing mode.4. After a few seconds, the SRC-System™ will show a solid RED light for 2 seconds, indicating that it is paired and ready to use.If Pairing is not completed within 2 minutes, the units will return to Standby mode. Repeat process from Step 2.5.3 MAKING INTERCOM CALLSMake Intercom Call In Standby, double tap or speak any word loudly into the microphone to call via VOXDuring Music playback, tap and a simultaneously.End Intercom call Tap Use VOX to make intercom calls using only your voice (see 4.5). VOX Intercom calls will end automatically after 30 seconds of silence.VOX and AGC performance will vary based on environmental conditions including riding speed, helmet type and ambient noise. For improved performance, minimize the wind impact on the microphones by closing the visor.5.4 RECEIVING INTERCOM CALLS• If a paired rider tries calling you via Intercom, the call will begin almost instantly• To receive a CTL intercom call see table in section 5.65.5 BUSY SIGNALA busy signal will be heard when attempting to establish an Intercom call with another device that is already on a phone or intercom call.
85.6 CLICK-TO-LINK® INTERCOM CTLClick-to-Link is the spontaneous, “social” feature of your SRC-System™. Use Click-to-Link to make intercom calls with other riders nearby without pre-pairing.Click-to-Link can be disabled on your unit eectively blocking any attempt by others to make Click-to-Link calls to you.Start a CTL call request (search lasts up to 10 seconds) In standby, tap and a simultaneouslyEnd a CTL call / Cancel a CTL call request Tap Accept a CTL callWhen hearing the CTL ringtone:Tap or say any word loudly to answer by VOXReject a CTL call Remain silent until the CTL ringtone stops or press for 2 secondsEnable/Disable CTL (Default: ENABLED) Via the App or the Cardo CommunityIf other riders are nearby, your next CTL call may randomly connect to any of them. 6. PAIRING AND USING A MOBILE PHONE, GPS DEVICE OR MP3 PLAYERTo connect your SRC-System™ to a Bluetooth device you must rst pair them. Once paired, they will automatically recognize each other whenever they are within range (10m / 33ft).Your SRC-System™ has two Bluetooth channels for connection to mobile phones, GPS devices and music players with A2DP.6.1 PAIRING BLUETOOTH CHANNELS 1 AND 21. Make sure Bluetooth is enabled on your phone/GPS/MP3 player.2. Check the SRC-System™ is in Standby (single BLUE ash every 3 seconds).3. To pair Bluetooth Channel 1 – press a for at least 5 seconds until the RED and BLUE LEDs begin rapidly alternating. To pair Bluetooth Channel 2 – press a for at least 5 seconds until the RED and BLUE LEDs begin rapidly alternating. To pair a GPS, when LEDs begin rapidly alternating, tap a.4. Search for Bluetooth devices on your phone/GPS/MP3 player by following the device’s instructions.5. After a few seconds the device will list “SRC-System”. Select it.6. If prompted for a PIN or Passkey, enter 0000 (four zeros).7. The device will conrm that pairing has succeeded and the SRC-System™ will begin ashing slowly in BLUE.8. If pairing is not completed within 2 minutes, the unit will return to Standby.
9 IMPORTANT!• If you have paired 2 dierent mobile phones directly to your SRC-System™, you will need to set one as default for making calls. During a phone call, press a for 5 seconds • If your GPS supports it, you can pair the second mobile phone directly to the GPS and then pair the GPS to your SRC-System™, and so connect both mobile phones and the GPS to your SRC-System™. NOTES: • Not all Bluetooth mobile phones can broadcast Bluetooth Stereo music (A2DP), even if the phone has an MP3 player function. Consult your mobile phone’s User Manual for more information.• Not all Bluetooth GPS devices allow connection to Bluetooth audio devices. Consult your GPS User Manual for more information.• After pairing, you may need to tap to connect the SRC-System™.6.2 RESET PAIRINGThis process will delete all paired devices.1. In Standby, press a for 5 secs until LED ashes RED/BLUE.2. Press for 2 seconds until LED ashes 5 times in PURPLE. 6.3 MAKING AND RECEIVING PHONE CALLSAnswer a call Tap or say any word loudly to answer by VOXReject a call Remain silent for 15 seconds, or press for 2 secondsEnd a call Tap Voice Dial*(if supported by mobile phone)In Standby, press a for 2 seconds and follow the prompt from the mobileRedial*In Standby, press a for 2 secondsHot-Dial** Tap three timesSet default phone*** When on a phone call, press a for 5 seconds * This feature is not available during mobile calls** To use the Hot-Dial feature, rst congure the phone number via the Cardo Community or SmartSet App.*** If you have 2 mobile phones paired directly to your SRC-System™, you will need to set one of them to use as default for outgoing calls. 6.4 LISTENING TO MUSIC VIA A2DPAvailable only on AVRCP compatible Bluetooth audio sourcesPlay In Standby, tap Pause/Stop Press for 2 secondsNext Track With music ON, tap Previous Track* With music ON, double tap A2DP scan With music ON, press a or a for 5 seconds to scan through your music tracks. *With some phones you may need to repeat this action
10SWITCHING BETWEEN A2DP AUDIO SOURCES1. Stop the music playback from the current device.2. Start music playback from the other device.7. TROUBLESHOOTINGReboot If your SRC-System™ stops responding, reset it by turning it o and then on again (press for 2 seconds). Reset Pairing(Deletes all paired devices)1. In Standby, press a for 5 secs until LED ashes RED/BLUE.2. Press for 2 seconds until LED ashes 5 times in PURPLE.8. SUPPORTFor additional information:  www.schuberth.com service@schuberth.com International: +49 391-8106-555Software updates are available via the Cardo Community (community.cardosystems.com) on your PC / Mac.In order to receive full Schuberth service and the latest news, please register your SRC-System™ at www.schuberth.com/register/en9. NOTICESImportant Notes:Riding a motorcycle, scooter, moped, ATV, quad bike or any other vehicle requires your full and undivided attention. You must ensure that you take all the necessary precautionary measures to be able to adequately take into account the current trac situation and weather conditions including the state of the road at all times, including when you are using the device. Before making or accepting a call you should pull over to the side of the road and stop. Any publications, advertisements, announcements or other similar communications, which imply that you can use the device on the move, merely refer to its technical capabilities and are not to be understood as an encouragement to engage in such activity.You must establish whether use of the device might represent a violation of any laws or regulations applicable in the location of use and adhere to the relevant rules. In this respect, any use of the device is exclusively at the user’s own risk and responsibility.The basic requirements for safe use include that you must be physically capable of using the device and not suer from any illness or restrictions that might impair your capability to use the device safely and ride on the road. Furthermore, you must hold a valid driving licence for the vehicle. Under no circumstances may you consume alcohol or mind altering drugs, which might impair your alertness, before or during use of the device.Operating temperature: The SRC-System™ is designed to work in temperatures between -20° and 55° C.AC/DC Adapters: When charging from a wall outlet, use the charger provided or another certied plug-in AC/DC adapter that meets the following criteria: Input: 100-240 V, 50/60 Hz, 0.2 A maximum Output: 5 DV DC, 1 A maximum.Federal Communications Commission (FCC) Statement 15.21You are cautioned that changes or modications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. FCC StatementThis equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may causeundesired operation.
1115.105(b)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC RF Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specic operating instructions for satisfying RF exposure compliance. The antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Industry Canada (IC)This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. IC RF Radiation Exposure Statement:This equipment complies with the RSS-102 exemption from routine RF exposure evaluation for use in an uncontrolled environment.European CE Notice The SRC-System™ headset (the “Product”) is in conformity with the following essential requirements of Council Directive 1999/5/EC (referred to as R&TTE Directive): Articles 3.1a, 3.1.b and 3.2. The Product is manufactured in accordance with Annex II of the above directive.Declaration of Conformity (DOC)The SRC-System™ headset is compliant with and adopts the Bluetooth® Specication 3.0 and has successfully passed all interoperability tests that are specied in the Bluetooth® specication. However, interoperability between the device and other Bluetooth®-enabled products is not guaranteed.WAIVER AND GENERAL RELEASE(not for countries of the European Union)BY USING THE SRCSYSTEM™ YOU WILL WAIVE SUBSTANTIAL LEGAL RIGHTS INCLUDING THE RIGHT TO SUE.PLEASE READ THE FOLLOWING CAREFULLY BEFORE USING THE DEVICE. IF YOU DO NOT ACCEPT ALL TERMS OF THIS AGREEMENT, YOU SHOULD IMMEDIATELY RETURN THE PRODUCT FOR A FULL REFUND. BY USING THE HEADSET YOU AGREE TO BE BOUND TO THIS AGREEMENT AND FORFEIT THE RIGHT TO SUE.Using a communication device while riding a motorcycle, scooter, moped, ATV, quad-bike or any other vehicle or equipment, whether on land, water or air (jointly referred to as “Vehicle”) requires your complete and undivided attention. Schuberth GmbH. and Cardo Systems, Inc., including their respective Ocers, Directors, Aliates, Parent Company, Representatives, Agents, Contractors, Sponsors, Employees, Suppliers and Resellers (jointly referred to as the “Company”) strongly advises you to take all necessary precautions and remain alert to the trac, weather and road conditions if you choose to use the SRC System (the “Device”) , including all derivative models irrespective of its commercial name or branding, and stop your Vehicle on the roadside prior to initiating or receiving calls. Any publications, advertisements, announcements or similar notes that refer to using the Device while riding a Vehicle are solely intended to address its technical capabilities and should not be misconstrued as if encouraging users to operate the Device while actively involved in trac.By way of purchasing this Device and not returning it for a full refund (see below), you are irrevocably releasing, indemnifying from any liability, loss, claim and expense (including attorneys fees) and holding the Company harmless for any bodily injuries, harm or death as well as losses or damages in goods, to any Vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdiction. the Company will not be responsible for any physical damages, irrespective of reasons, conditions or circumstances, including malfunctioning of the Device, and all risks associated with operating it rest solely and entirely with the user of this Device, irrespective of whether the Device is used by the original purchaser or any third party.The Company hereby noties you that using this Device may also be in contravention to local, federal, state or national laws or regulations, and that any use of the Device is entirely at your sole risk and responsibility.1. You, your heirs, legal representatives, successors or assigns, hereby voluntarily and forever release, discharge, indemnify and hold harmless the Company from any and all litigation, claims, debts, demands, actions and liability which may arise, directly or indirectly, from using the Device for any distress, pain, suering, discomfort, loss, injury, death, damages to or in respect to any person or property however caused, WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to you on some future date as a result of said use, to the fullest extent permitted by law.2. You fully understand and assume the risks in using the Device, including risk of negligent acts or omissions by others.
123. You conrm that you are physically capable to use the Device and that you have no medical conditions or needs that may infringe upon your abilities to do so in a safe manner. You conrm that you are at least eighteen (18) years of age and that you have been advised of the risks associated with the use of the Device. You further conrm that you will not consume any alcohol that may aect your alertness or any mind-altering substance, and will not carry, use or consume these substances before or during the use of the Device.4. You fully acknowledge our warnings and understand that: (a) risks and dangers exist in using the Device while in trac, including but not limited to injury or illness, strains, fractures, partial and/or total paralysis, death or other ailments that could cause serious disability; (b) these risks and dangers may be caused by the negligence of the manufacturers or its agents or any third party involved in designing or manufacturing the Device; (c) these risks and dangers may arise from foreseeable or unforeseeable causes. You hereby assume all risks and dangers and all responsibility for any losses and/ or damages, whether caused in whole or in part by the negligence or other conduct of others, including the Company.5. You conrm that you have read this release of liability and fully understand its terms and that you have given up substantial rights by not returning the Device for a full refund (see refund option below).Disclaimer of WarrantyTHE COMPANY DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. THE DEVICE AND ITS ACCESSORIES ARE PROVIDED “AS IS” AND “AS AVAILABLE” WITHOUT WARRANTY OF ANY KIND BEYOND THOSE ASSUMED IN THE ENCLOSED MANUAL.Limitation of LiabilityIN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THE DEVICE, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.YOU ACKNOWLEDGE AND AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE FUNDAMENTAL ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT BE PROVIDED TO YOU ABSENT SUCH LIMITATIONS. SOME STATE STATUTES MIGHT APPLY REGARDING LIMITATION OF LIABILITY.RETURN FOR FULL REFUNDIF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS, YOU MAY RETURN THIS DEVICE TO THE RESELLER OR TO THE COMPANY FOR A FULL REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 7 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE (proof of purchase required) AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING SO, PLEASE REFER TO THIS SECTION. BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE PERIOD PROVIDED, YOU ARE EXPLICITLY IN AGREEMENT WITH THE ABOVE, AND RENOUNCE ALL RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST THE COMPANY AS DEFINED ABOVE.www.schuberth.com

Navigation menu