Cardo Systems ER18 Bluetooth headset User Manual SRC System EN
Cardo Systems, Inc. Bluetooth headset SRC System EN
Users Manual(rev1)
USER MANUAL
POWERED BY
communication in motion®
2
CONTENTS
1. INTRODUCTION ..............................................3
2. CHARGING THE BATTERY .....................................4
3. UPDATES AND SETTINGS .....................................4
4. GETTING STARTED ...........................................5
4.1 INSTALLATION ................................................5
4.2 GENERAL FUNCTIONS ........................................6
4.3 STATUS LIGHTS ...............................................6
4.4 AUDIO SOURCES AND PRIORITIES ............................6
4.5 VOICE CONNECT VOX SETTINGS .............................6
5. INTERCOM ...................................................7
5.1 INTERCOM COMPATIBILITY ....................................7
5.2 PAIRING THE INTERCOM CHANNEL ...........................7
5.3 MAKING INTERCOM CALLS ...................................7
5.4 RECEIVING INTERCOM CALLS .................................7
5.5 BUSY SIGNAL .................................................7
5.6 CLICKTOLINK® INTERCOM CTL ..............................8
6. PAIRING AND USING A MOBILE PHONE, GPS DEVICE OR
MP3 PLAYER .................................................8
6.1 PAIRING BLUETOOTH CHANNELS 1 AND 2 .....................8
6.2 RESET PAIRING ................................................9
6.3 MAKING AND RECEIVING PHONE CALLS ......................9
6.4 LISTENING TO MUSIC VIA A2DP ...............................9
7. TROUBLESHOOTING .........................................10
8. SUPPORT ...................................................10
9. NOTICES ....................................................10
CONTENTS OF RETAIL BOX
If you purchased the SRC-System™ DUO, your retail box contains
two factory-paired SRC-System™ units and two of each item listed
below.
SRC-System™
1
Micro USB (•)
2
Volume Up (a)
3
Schuberth Button ( )
4
Volume Down (a)
5
LED
Wall charger plug
3
USB cable
4
3
1. INTRODUCTION
Thank you for choosing the SRC-System™ Bluetooth®
communication and entertainment system for motorcycle
helmets. This manual will help you set up, congure and use the
SRC-System™.
INTERCOM OPTIONS IN FULL DUPLEX
• Bike-to-Bike intercom at a range of up to 500m
• Rider-to-Passenger intercom
• Click-to-Link® Intercom: For spontaneous connection with other
riders nearby who have CTL-enabled devices
MULTIPLE DEVICE CONNECTIVITY
• 2 Bluetooth connections for mobile phones / MP3 Players / GPS
Navigation devices
• Other riders via intercom
ENTERTAINMENT OPTIONS
• Wireless music streaming via devices supporting Bluetooth Stereo
A2DP and AVRCP proles
CARDO COMMUNITY®AND CARDO SMARTSET APP*
• Customize the settings via your computer or smartphone
• Download software upgrades, enhancements and new features
*App available on Android and iOS devices
ADVANCED TECHNOLOGY
➤ AGC (Automatic Gain Control) technology, for the automatic
adjustment of volume according to ambient noise and driving
speed. You can also control the volume level manually. AGC
sensitivity levels can be customized to suit your personal
preferences.
➤ VOX technology for safe, hands-free operation of key functions.
VOX sensitivity levels can be customized to suit your personal
preferences.
➤ PLC (Packet Loss Concealment) software for real-time
compensation of audio losses in challenging environments.
➤ Spoken status announcements, so that you always know to
whom or to what device you are connected.
➤ Volume Per Mode: Volume is set and saved at dierent levels for
each audio source.
We wish you a great SRC-System™ experience!
This is version 1.0 of the User Manual. Please note, that our manual
is periodically updated on the Schuberth website to include the very
latest features and functions of your new SRC-System™.
4
2. CHARGING THE BATTERY
Make sure that your unit is fully charged for at least 3 hours before
initial use. Charging with the wall charger is faster than via a
computer USB port.
• RED LED ON – Charging
• RED LED OFF – Charging complete
The battery level can be checked on the Android app or on
iPhones running iOS 5 or later using the Bluetooth headset battery
indicator feature. The icon appears automatically once you have
paired and connected your SRC-System™ to the phone.
IMPORTANT:
The SRC-System™ is waterproof and dustproof. However,
when in use, the USB silicone cover should be kept tightly
closed to prevent moisture from entering the unit.
3. UPDATES AND SETTINGS
Get the most out of your SRC-System™ by changing the settings
and customizing your unit according to your own personal
preferences.
Software updates are available via the Cardo Community on your
PC / Mac*. Settings can be changed either by the Cardo Community
or the Cardo SmartSet App on a compatible smartphone.
In order to receive full Schuberth service and the latest news, please
register your SRC-System™ at www.schuberth.com/register/en
Cardo
Community
SmartSet
App
Download the latest software upgrade
Set your Hot-Dial number
Change A2DP / Intercom audio priority
Spoken Status Announcements
Change AGC sensitivity for the speakers
Change VOX sensitivity for the microphone
Click-to-Link Enable/Disable
CARDO COMMUNITY WEB PLATFORM
Visit http://community.cardosystems.com
*Minimum requirement:
Windows® XP or later / Mac OS X® 10.6 or later
Mac and Mac OS are trademarks of Apple Inc.,
registered in the U.S. and other countries.
5
Cardo
SmartSet
App
CARDO SMARTSET APP
4. GETTING STARTED
4.1 INSTALLATION
6
4.2 GENERAL FUNCTIONS
Power ON Press for 2 seconds
3 BLUE ashes with ascending tone
Power OFF In Standby, press for 2 seconds
3 RED ashes with descending tone
Volume Tap
a
or
a
to adjust and set volume of current
audio source
Mute / Unmute Tap
a
and
a
simultaneously
Enable / Disable
VOX (For Intercom
calls only)
In standby, press
a
and
a
simultaneously for
2 seconds
ENABLED: Blue ash for 2 seconds
DISABLED: Red ash for 2 seconds
4.3 STATUS LIGHTS
None SRC-System™ is OFF
1 BLUE ash every 3 seconds Standby mode
No active audio sources
2 BLUE ashes every
3 seconds
Active mode – Call in progress / music
or other audio source is ON
1 RED ash every 3 seconds Standby mode – Battery is low
2 RED ashes every 3 seconds Active mode – Battery is low
Solid RED Charging
4.4 AUDIO SOURCES AND PRIORITIES
If two connected audio sources try to play audio simultaneously, your
SRC-System™ automatically determines which audio source to play
through the speakers based on the priority of the connected devices.
Higher Priority 1. Mobile Phone audio or GPS instructions*
2. Intercom / Click-to-Link
3. A2DP (Stereo Bluetooth) audio
* GPS instructions from Smartphone GPS Apps are
prioritized like A2DP audio
Lower Priority
For example:
• Incoming mobile phone calls interrupt ongoing intercom calls
• Incoming intercom calls will interrupt ongoing A2DP music
• Intercom and Click-to-Link calls have the same priority. So
Click-to-Link calls will not interrupt any Intercom call in progress,
and vice-versa.
A2DP audio priority can be congured higher than Intercom audio
priority – see section 3.
4.5 VOICE CONNECT VOX SETTINGS
Your SRC-System™ oers VOX technology for safe and hands-free
operation of some key functions.
The VOX can be customized to adjust its sensitivity level. VOX
activation for Intercom calls can also be disabled completely.
You can choose between ‘High’, ‘Medium’ (default) and ‘Low’ VOX
sensitivity.
If you experience diculties starting a conversation using VOX,
change setting to ‘High’.
If VOX keeps starting calls involuntarily, change setting to ‘Low’.
7
5. INTERCOM
The SRC-System™ allows Bike-to-Bike and Rider-to-Passenger full-
duplex intercom communication at a range of up to 500m.
To chat via Intercom, you must rst pair your SRC-System™ to the
second device. Pairing is a one-time process. Once paired, the
two units will automatically recognize each other whenever in
range.
5.1 INTERCOM COMPATIBILITY
Your SRC-System™ is compatible with all Schuberth SRC-Systems™.
In addition, it is also compatible with the scala rider line of
intercom models. Range is limited to the distance of the device
with the shorter range.
For details of which scala rider models are compatible, and how
to pair and use your SRC-System™ with other models, please visit
www.cardosystems.com/SRC.
5.2 PAIRING THE INTERCOM CHANNEL
Pairing will replace any existing paired device with the new device.
If you have purchased the SRC-System™ DUO, the retail package
contains two pre-paired units.
If for any reason you have to pair them again, OR if you wish to pair
another unit, proceed as follows:
1. Check both units are in Standby.
2. On the SRC-System™, press for 5 seconds. The LED will begin
ashing RED and the unit will now enter intercom pairing mode.
3. Enter intercom pairing mode on the second unit by following
the device’s user manual. Both units will now be in intercom
pairing mode.
4. After a few seconds, the SRC-System™ will show a solid RED
light for 2 seconds, indicating that it is paired and ready to use.
If Pairing is not completed within 2 minutes, the units will return to
Standby mode. Repeat process from Step 2.
5.3 MAKING INTERCOM CALLS
Make Intercom Call In Standby, double tap or speak any word
loudly into the microphone to call via VOX
During Music playback, tap and
a
simultaneously.
End Intercom call Tap
Use VOX to make intercom calls using only your voice (see 4.5).
VOX Intercom calls will end automatically after 30 seconds of
silence.
VOX and AGC performance will vary based on environmental
conditions including riding speed, helmet type and ambient noise.
For improved performance, minimize the wind impact on the
microphones by closing the visor.
5.4 RECEIVING INTERCOM CALLS
• If a paired rider tries calling you via Intercom, the call will begin
almost instantly
• To receive a CTL intercom call see table in section 5.6
5.5 BUSY SIGNAL
A busy signal will be heard when attempting to establish an
Intercom call with another device that is already on a phone or
intercom call.
8
5.6 CLICK-TO-LINK® INTERCOM CTL
Click-to-Link is the spontaneous, “social” feature of your SRC-System™.
Use Click-to-Link to make intercom calls with other riders nearby
without pre-pairing.
Click-to-Link can be disabled on your unit eectively blocking any
attempt by others to make Click-to-Link calls to you.
Start a CTL call request
(search lasts up to 10 seconds) In standby, tap and
a
simultaneously
End a CTL call /
Cancel a CTL call request Tap
Accept a CTL call
When hearing the CTL ringtone:
Tap or say any word loudly to answer
by VOX
Reject a CTL call Remain silent until the CTL ringtone
stops or press for 2 seconds
Enable/Disable CTL
(Default: ENABLED) Via the App or the Cardo Community
If other riders are nearby, your next CTL call may randomly connect
to any of them.
6. PAIRING AND USING A MOBILE PHONE,
GPS DEVICE OR MP3 PLAYER
To connect your SRC-System™ to a Bluetooth device you must rst
pair them. Once paired, they will automatically recognize each
other whenever they are within range (10m / 33ft).
Your SRC-System™ has two Bluetooth channels for connection to
mobile phones, GPS devices and music players with A2DP.
6.1 PAIRING BLUETOOTH CHANNELS 1 AND 2
1. Make sure Bluetooth is enabled on your phone/GPS/MP3 player.
2. Check the SRC-System™ is in Standby (single BLUE ash every
3 seconds).
3. To pair Bluetooth Channel 1 – press
a
for at least 5 seconds
until the RED and BLUE LEDs begin rapidly alternating.
To pair Bluetooth Channel 2 – press
a
for at least 5 seconds
until the RED and BLUE LEDs begin rapidly alternating.
To pair a GPS, when LEDs begin rapidly alternating, tap
a
.
4. Search for Bluetooth devices on your phone/GPS/MP3 player by
following the device’s instructions.
5. After a few seconds the device will list “SRC-System”. Select it.
6. If prompted for a PIN or Passkey, enter 0000 (four zeros).
7. The device will conrm that pairing has succeeded and the
SRC-System™ will begin ashing slowly in BLUE.
8. If pairing is not completed within 2 minutes, the unit will return
to Standby.
9
IMPORTANT!
• If you have paired 2 dierent mobile phones directly to your
SRC-System™, you will need to set one as default for making calls.
During a phone call, press
a
for 5 seconds
• If your GPS supports it, you can pair the second mobile phone
directly to the GPS and then pair the GPS to your SRC-System™,
and so connect both mobile phones and the GPS to your
SRC-System™.
NOTES:
• Not all Bluetooth mobile phones can broadcast Bluetooth Stereo
music (A2DP), even if the phone has an MP3 player function.
Consult your mobile phone’s User Manual for more information.
• Not all Bluetooth GPS devices allow connection to Bluetooth audio
devices. Consult your GPS User Manual for more information.
• After pairing, you may need to tap to connect the
SRC-System™.
6.2 RESET PAIRING
This process will delete all paired devices.
1. In Standby, press
a
for 5 secs until LED ashes RED/BLUE.
2. Press for 2 seconds until LED ashes 5 times in PURPLE.
6.3 MAKING AND RECEIVING PHONE CALLS
Answer a call Tap or say any word loudly to answer by VOX
Reject a call Remain silent for 15 seconds, or press for
2 seconds
End a call Tap
Voice Dial*
(if supported by
mobile phone)
In Standby, press
a
for 2 seconds and follow the
prompt from the mobile
Redial*In Standby, press
a
for 2 seconds
Hot-Dial** Tap three times
Set default phone*** When on a phone call, press
a
for 5 seconds
* This feature is not available during mobile calls
** To use the Hot-Dial feature, rst congure the phone number via the
Cardo Community or SmartSet App.
*** If you have 2 mobile phones paired directly to your SRC-System™, you will need
to set one of them to use as default for outgoing calls.
6.4 LISTENING TO MUSIC VIA A2DP
Available only on AVRCP compatible Bluetooth audio sources
Play In Standby, tap
Pause/Stop Press for 2 seconds
Next Track With music ON, tap
Previous Track* With music ON, double tap
A2DP scan With music ON, press
a
or
a
for 5 seconds to
scan through your music tracks.
*With some phones you may need to repeat this action
10
SWITCHING BETWEEN A2DP AUDIO SOURCES
1. Stop the music playback from the current device.
2. Start music playback from the other device.
7. TROUBLESHOOTING
Reboot If your SRC-System™ stops responding, reset it
by turning it o and then on again (press for
2 seconds
)
.
Reset Pairing
(Deletes all
paired devices)
1. In Standby, press
a
for 5 secs until LED ashes
RED/BLUE.
2. Press for 2 seconds until LED ashes 5 times in
PURPLE.
8. SUPPORT
For additional information:
www.schuberth.com
service@schuberth.com
International: +49 391-8106-555
Software updates are available via the Cardo Community
(community.cardosystems.com) on your PC / Mac.
In order to receive full Schuberth service and the latest news, please
register your SRC-System™ at www.schuberth.com/register/en
9. NOTICES
Important Notes:
Riding a motorcycle, scooter, moped, ATV, quad bike or any other vehicle requires your full and
undivided attention. You must ensure that you take all the necessary precautionary measures
to be able to adequately take into account the current trac situation and weather conditions
including the state of the road at all times, including when you are using the device. Before
making or accepting a call you should pull over to the side of the road and stop. Any publications,
advertisements, announcements or other similar communications, which imply that you can use
the device on the move, merely refer to its technical capabilities and are not to be understood as
an encouragement to engage in such activity.
You must establish whether use of the device might represent a violation of any laws or
regulations applicable in the location of use and adhere to the relevant rules. In this respect, any
use of the device is exclusively at the user’s own risk and responsibility.
The basic requirements for safe use include that you must be physically capable of using the device
and not suer from any illness or restrictions that might impair your capability to use the device
safely and ride on the road. Furthermore, you must hold a valid driving licence for the vehicle.
Under no circumstances may you consume alcohol or mind altering drugs, which might impair
your alertness, before or during use of the device.
Operating temperature: The SRC-System™ is designed to work in temperatures between -20°
and 55° C.
AC/DC Adapters: When charging from a wall outlet, use the charger provided or another
certied plug-in AC/DC adapter that meets the following criteria:
Input: 100-240 V, 50/60 Hz, 0.2 A maximum
Output: 5 DV DC, 1 A maximum.
Federal Communications Commission (FCC)
Statement 15.21
You are cautioned that changes or modications not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment.
FCC Statement
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
11
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specic operating instructions for satisfying RF exposure
compliance. The antenna used for this transmitter must not transmit simultaneously with any other
antenna or transmitter, except in accordance with FCC multi-transmitter product procedures.
Industry Canada (IC)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
IC RF Radiation Exposure Statement:
This equipment complies with the RSS-102 exemption from routine RF exposure evaluation for use in
an uncontrolled environment.
European CE Notice
The SRC-System™ headset (the “Product”) is in conformity with the following essential
requirements of Council Directive 1999/5/EC (referred to as R&TTE Directive): Articles 3.1a, 3.1.b
and 3.2. The Product is manufactured in accordance with Annex II of the above directive.
Declaration of Conformity (DOC)
The SRC-System™ headset is compliant with and adopts the Bluetooth® Specication 3.0 and
has successfully passed all interoperability tests that are specied in the Bluetooth® specication.
However, interoperability between the device and other Bluetooth®-enabled products is not
guaranteed.
WAIVER AND GENERAL RELEASE
(not for countries of the European Union)
BY USING THE SRCSYSTEM™ YOU WILL WAIVE SUBSTANTIAL LEGAL RIGHTS INCLUDING THE
RIGHT TO SUE.
PLEASE READ THE FOLLOWING CAREFULLY BEFORE USING THE DEVICE. IF YOU DO NOT ACCEPT
ALL TERMS OF THIS AGREEMENT, YOU SHOULD IMMEDIATELY RETURN THE PRODUCT FOR A FULL
REFUND. BY USING THE HEADSET YOU AGREE TO BE BOUND TO THIS AGREEMENT AND FORFEIT
THE RIGHT TO SUE.
Using a communication device while riding a motorcycle, scooter, moped, ATV, quad-bike or
any other vehicle or equipment, whether on land, water or air (jointly referred to as “Vehicle”)
requires your complete and undivided attention. Schuberth GmbH. and Cardo Systems, Inc.,
including their respective Ocers, Directors, Aliates, Parent Company, Representatives, Agents,
Contractors, Sponsors, Employees, Suppliers and Resellers (jointly referred to as the “Company”)
strongly advises you to take all necessary precautions and remain alert to the trac, weather and
road conditions if you choose to use the SRC System (the “Device”) , including all derivative models
irrespective of its commercial name or branding, and stop your Vehicle on the roadside prior to
initiating or receiving calls. Any publications, advertisements, announcements or similar notes
that refer to using the Device while riding a Vehicle are solely intended to address its technical
capabilities and should not be misconstrued as if encouraging users to operate the Device while
actively involved in trac.
By way of purchasing this Device and not returning it for a full refund (see below), you are irrevocably
releasing, indemnifying from any liability, loss, claim and expense (including attorneys fees) and
holding the Company harmless for any bodily injuries, harm or death as well as losses or damages
in goods, to any Vehicles including your own, or to any property or asset that belong to you or to
third parties, any of which may result from using the Device under any circumstances or conditions
and irrespective of jurisdiction. the Company will not be responsible for any physical damages,
irrespective of reasons, conditions or circumstances, including malfunctioning of the Device, and all
risks associated with operating it rest solely and entirely with the user of this Device, irrespective of
whether the Device is used by the original purchaser or any third party.
The Company hereby noties you that using this Device may also be in contravention to local,
federal, state or national laws or regulations, and that any use of the Device is entirely at your sole
risk and responsibility.
1. You, your heirs, legal representatives, successors or assigns, hereby voluntarily and forever
release, discharge, indemnify and hold harmless the Company from any and all litigation,
claims, debts, demands, actions and liability which may arise, directly or indirectly, from using
the Device for any distress, pain, suering, discomfort, loss, injury, death, damages to or in
respect to any person or property however caused, WHETHER ARISING FROM THE NEGLIGENCE
OR OTHERWISE, and which may hereafter accrue to you on some future date as a result of said
use, to the fullest extent permitted by law.
2. You fully understand and assume the risks in using the Device, including risk of negligent acts or
omissions by others.
12
3. You conrm that you are physically capable to use the Device and that you have no medical
conditions or needs that may infringe upon your abilities to do so in a safe manner. You conrm
that you are at least eighteen (18) years of age and that you have been advised of the risks
associated with the use of the Device. You further conrm that you will not consume any
alcohol that may aect your alertness or any mind-altering substance, and will not carry, use or
consume these substances before or during the use of the Device.
4. You fully acknowledge our warnings and understand that:
(a) risks and dangers exist in using the Device while in trac, including but not limited to injury
or illness, strains, fractures, partial and/or total paralysis, death or other ailments that could
cause serious disability;
(b) these risks and dangers may be caused by the negligence of the manufacturers or its agents
or any third party involved in designing or manufacturing the Device;
(c) these risks and dangers may arise from foreseeable or unforeseeable causes. You hereby
assume all risks and dangers and all responsibility for any losses and/ or damages, whether
caused in whole or in part by the negligence or other conduct of others, including the Company.
5. You conrm that you have read this release of liability and fully understand its terms and that
you have given up substantial rights by not returning the Device for a full refund (see refund
option below).
Disclaimer of Warranty
THE COMPANY DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED
DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. THE DEVICE AND ITS ACCESSORIES ARE
PROVIDED “AS IS” AND “AS AVAILABLE” WITHOUT WARRANTY OF ANY KIND BEYOND THOSE ASSUMED
IN THE ENCLOSED MANUAL.
Limitation of Liability
IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL,
EXEMPLARY OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM THE
USE OF THE DEVICE, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE),
PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
YOU ACKNOWLEDGE AND AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE FUNDAMENTAL
ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT BE PROVIDED TO YOU ABSENT SUCH
LIMITATIONS. SOME STATE STATUTES MIGHT APPLY REGARDING LIMITATION OF LIABILITY.
RETURN FOR FULL REFUND
IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS, YOU MAY RETURN THIS
DEVICE TO THE RESELLER OR TO THE COMPANY FOR A FULL REFUND, PROVIDED THAT YOU DO SO
NO LATER THAN 7 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE (proof of purchase
required) AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING SO, PLEASE REFER TO THIS
SECTION. BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE PERIOD PROVIDED, YOU ARE
EXPLICITLY IN AGREEMENT WITH THE ABOVE, AND RENOUNCE ALL RIGHTS TO FUTURE CLAIMS AND
DEMANDS AGAINST THE COMPANY AS DEFINED ABOVE.
www.schuberth.com