Carel s p a LEGWB Bluetooth Gateway User Manual rev 1

Carel Industries s.p.a. Bluetooth Gateway rev 1

user manual rev 1

+050002725 - rel. 1.0 -  08.01.2018Wireless Gateway: GTW**0BT0: Gateway Serial RS485/TTL to Bluetooth  /  GTW**0WT0: Gateway Serial RS485/TTL to WiFi     Bluetooth version                  Wi- versionInstallazione e montaggio Dimensioni e forature (in mm) 2541486070Ø 42563.5Fig.1Collegamento elettrico, rete RS485 1234567POWERLINKDC:5~36V DC:5~36VResetSerial TTLRS485GatewaySerial to Bluetooth                 1234567POWERLINKDC:5~36V DC:5~36VResetSerial TTLRS485GatewaySerial to WiFiLegenda:1Porta seriale RS485 2Porta seriale TTL (per connettersi ai controlli parametrici come IR33 modbus - senza l’uso di IROPZ485xx)3Antenna4Alimentazione Jack-Maschio 5Alimentazione morsetti a vite 6Led di stato:Verde = LinkRosso = Power 7Tasto di reset •  Seguire gli schemi indicati utilizzando cavo schermato per reti RS485. NON collegare la resistenza di terminazione da 120 Ω sull’ultimo dispositivo della rete in quanto la porta Rs485 è di tipo HW slave, il numero massimo di dispositivi collegabili nella rete è 1 e la lunghezza massima della rete è 100m.IntroduzioneGateways wireless sono convertitori da rete seriale a wi o bluetooth, con comunicazione bi-direzionale e semplice funzionalità di connessione.Contenuto della confezione•  Gateway;•  Antenna;•  Foglio istruzioni;•  Morsetti a vite.Avvertenze d’installazionePer un montaggio corretto contattare un montatore qualicato. Non installare prodotti in ambienti aventi le seguenti caratteristiche:•  umidità relativa superiore al valore specicato nelle caratteristiche tecniche;•  forti vibrazioni o urti;•  esposizione ad atmosfere aggressive e inquinanti (ad es.: fumi di zolfo e ammoniaca, nebbia salina, fumo) per evitare corrosione e/o ossidazione;•  forti interferenze magnetiche e/o di radiofrequenze (pertanto si consiglia di montare le unità vicino alle antenne di trasmissione);•  esposizione a luce solare diretta o agli elementi atmosferici in genere;•  importanti e rapidi uttuazioni della temperatura ambiente;•  ambienti nei quali sono presenti esplosivi o miscele di gas inammabili.È necessario rispettare i seguenti avvertimenti:•  AVVERTENZA: per i collegamenti elettrici, rispettare la polarità indicata sul connettore all’interno della scatola; •  utilizzare unicamente cavi schermati per la rete di comunicazione RS485;•  tensioni di alimentazione diverse da quelle specicate possono gravemente danneggiare il sistema;•  usare dei capicorda appropriati per i relativi morsetti. Allentare le singole viti e inserire i capicorda, quindi serrare le viti. Al termine, tirare leggermente i cavi per accertarsi che siano tesi a sucienza;•  non aprire il prodotto quando è alimentato.Verifica stato alimentazione (power LED)LED rosso = alimentato correttamente - LED spento  = non alimentatoMessa in servizo versione WI-FI•  Collegare il GTW Carel: l’SSID di default di Carel è CAREL_GTW_SERIAL2WIFI_XXXXXX, XXXXXX corrisponde agli ultimi byte dell’indirizzo MAC, l’SSID è riportato sull’etichetta. Collegare l’SSID Wireless al PC o altri dispositivi.•  Login nella Congure Page: aprire l’indirizzo http://10.10.100.254 nel browser web.  Si apre un login dialogue, immettere il nome utente di default “admin” e la password “admin”, si accede alla pagina WiFi congure.•  WiFi Setting: la Pagina WiFi Setting è la seguente:Ci sono due modalità WiFi Work: AP mode e STA mode. La modalità di default è AP mode. L’AP mode ha i seguenti parametri:•  Network Name (SSID): l’SSID di default è CAREL_GTW_SERIAL2WIFI_XXXXXX.  XXXXXX corrisponde agli ultimi byte dell’indirizzo MAC•  Password: nessuna password di default, visualizzazione “NONE”•  Indirizzo IP: default 10.10.100.254•  Mask: 255.255.255.0La pagina di impostazione STA mode è come riportato di anco:L’STA mode ha i seguenti parametri:•  Router SSID: l’SSID al quale volete collegarvi si individua usando la funzione “search” per ricercare e selezionare uno degli SSID di rete, come SSID del sistema BOSS.•  STA Password: la password dell’SSID, se la rete wireless non ha password, deve essere impostata come “NONE”.•  DHCP: la funzione DHCP è abilitata di default. Si può disabilitare il DHCP ed impostare l’indirizzo IP statico e i relativi Mask, Gateway e DNS• •  Trans Setting: la pagina Trans Setting è la seguente:La Trans Setting ha i seguenti parametri:•  Serial Port Set: parametri della porta seriale RS485.•  NetWork Set: mantiene la modalità transparent di default.•  Socket A Connect Set: congurare i parametri della presa A, quando ci si collega al sistema BOSS Carel; l’STA WiFi funziona come server TCP e la porta è la 502. In modalità TCP-Server, ignorare il Server IP Address.•  Socket B Connect Set: come per la presa A, disabilitato per default.•  Save and Restart: una volta congurate le pagine, salvare i cambiamenti. Fare ripartire il GTW dopo avere completato tutte le impostazioni.•  Connect With CAREL BOSS System: dopo avere congurato il GTW CAREL, procedere come segue:•  Modalità STA•  BOSS Wireless SSID e password•  Modalità TCP server e porta 502•  controllare su ksa.carel.com nella sezione boss (FAQ) tutte le istruzioni aggiuntive necessarie per collegare il dispositivo alla rete WiFi bossMessa in servizo versione BLUETOOTH•  Accendere il dispositivo Bluetooth e cercare il dispositivo “CAREL_GTW_SERIAL2BT_xxxxxx” (dove xxxxxx sono i 3 byte nali dell’indirizzo MAC)•  Collegarsi a quest’ultimo;•  Aprire l’app APPLICA, controllare su ksa.carel.com tutti i le e le istruzioni aggiuntivi necessari per collegare il dispositivoSpecifiche tecnicheHardwareAlimentazione 5…36 V ccCorrente di esercizio (modulo WiFi interno)Modalità normale: Modalità sleep:Deep dormancy:AP media: 74 mA,  picco 285 mASTA media: 32 mA,  picco 196 mA6,5 mA90 μATemper. di esercizio -10…60°CUmidità di esercizio 5…95% UR (non-cond)Interfaccia comune RS485, TTLWirelessWireless Standard 802.11 b/g/nTrasmissione di potenza802.11b: +18 +/-1 dBm (@ 11 Mbps CCK)802.11g: +17 +/-1 dBm (@ 54 Mbp OFDM)802.11n: +15 +/-1 dBm (@ HT20, MCS7)Sensibilità di ricezione802.11b: -85 dBm (@ 11 Mbps CCK)802.11g: -70 dBm (@ 54 Mbps OFDM)802.11n: -68 dBm (@ HT20 MCS7)Antenna Antenna ad asta esterna con un connettore non standardSoftwareTipi di rete Wireless AP / STAZIONESicurezza WiFi WEP/WPA-PSK/WPA2-PSKWiFi Encryption TKIP, AES, TKIP/AESGamma di frequenza di esercizioBluetooth 2402-2480 MHz - Max. potenza di messa a punto con tolleranza -3±1,0 dBmWiFi 2412-2462 MHzMax. potenza di messa a punto con tolleranza 11B:18±1 dBm11G:17±1 dBm11N:15±1 dBmVERSIONE ITALIANO / ITALIAN VERSION Smaltimento del prodotto: L’apparecchiatura (o il prodotto) deve essere oggetto di raccolta separata in conformità alle vigenti normative locali in materia di smaltimento.
CAREL Industries HQsVia dell’Industria, 11 - 35020 Brugine - Padova (Italy)Tel. (+39) 0499716611 – Fax (+39) 0499716600 – www.carel.com – e-mail: carel@carel.com +050002725 - rel. 1.0 -  08.01.2018 Important warnings for FCC rulesThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation.Caution: The user is cautioned that changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:•  Reorient or relocate the receiving antenna.•  Increase the separation between the equipment and receiver.•  Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.•  Consult the dealer or an experienced radio/TV technician for help.•  This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Disposal of the product: The appliance (or the product) must be disposed of separately in compliance with the local standards in force on waste disposal.Assembly and installationDimensions and drilling template2541486070Ø 42563.5Fig.1Power and RS485 network connection1234567POWERLINKDC:5~36V DC:5~36VResetSerial TTLRS485GatewaySerial to Bluetooth                 1234567POWERLINKDC:5~36V DC:5~36VResetSerial TTLRS485GatewaySerial to WiFiLegende:1RS485 Serial Port2TTL Serial Port (to connect to parametric controller as IR33 modbus - without use of IROPZ485xx)3Antenna4Male-Jack Power supply5Screw power supply6Status leds7Reset button•  Follow the diagrams shown, use shielded cables DO NOT connect the 120Ω terminal resistor into the last devices of the Rs485 network, this is because the Rs485 port is HW Slave type. The max. number of devices which can be connected in the network is 1, and the maximum lenght of it is 100 meters.IntroductionThe Wireless Gateways are serial to wi or bluetooth converters, for data bi-directional transmission with smart link functions.Packaging contents•  Gateway;•  Antenna;•  Instruction sheet;•  Screw terminals.Installation warningsFor correct installation contact a qualied installer. Do not install products in environments with the following characteristics:•  relative humidity greater than the value specied in the technical specications;•  strong vibrations or knocks;•  exposure to aggressive and polluting atmospheres (e.g.: sulphur and ammonia fumes, saline mist, smoke) so as to avoid corrosion and/or oxidation;•  strong magnetic and/or radio frequency interference (therefore avoid installing the units near transmitting antennae);•  exposure to direct sunlight or the elements in general;•  large and rapid uctuations in the room temperature;•  environments where explosives or mixes of ammable gases are present.The following warnings must be observed:•  ATTENTION: For the electrical connection, maintain the polarity indicated on the connector included in the box; •  only use shielded cables for the RS485 communication network;•  power supply voltages other than those specied may seriously damage the system;•  use cable ends suitable for the corresponding terminals. Loosen each screw and insert the cable ends, then tighten the screws. When nished, slightly tug the cables to check they are suciently tight;•  do not open the product when powered.Check power onRed LED = Powered correctly - LED O  = Not poweredFirst commissioning WI-FI version•  Connect the Carel GTW: the Carel default SSID is CAREL_GTW_SERIAL2WIFI_XXXXXX, XXXXXX is the last bytes of the MAC address, you can nd the SSID on the label. Connect this Wireless SSID with the PC or other devices.•  Login the Congure Page: open the address http://10.10.100.254 in your web browser.  You will meet a login dialogue, enter the default username “admin” and the password “admin”, you will access the WiFi congure page.•  WiFi Setting: the WiFi Setting Page Likes bellow:There are two WiFi Work Modes: AP mode and STA mode. The default mode is AP mode. The AP mode has bellow parameters:•  Network Name (SSID): The default SSID is CAREL_GTW_SERIAL2WIFI_XXXXXX.  XXXXXX is the last bytes of the MAC address•  Password: No pass word by default, show as “NONE”•  IP Address: default 10.10.100.254•  Mask: 255.255.255.0STA mode setting page likes on side:The STA mode has bellow parameters:•  Router SSID:the SSID you want to connect with, you can use the “search” function to search and select one network SSID, such BOSS system’s SSID.•  STA Password: the password of the SSID , if the wireless network has no password, set it as “NONE”.•  DHCP: The DHCP function, default enabled. You can disable the DHCP and set the static IP address and related Mask, Gateway and DNS•  Trans Setting: the Trans Setting page likes:The Trans Setting has bellow parameters:•  Serial Port Set:  the RS485 serial port parameters.•  NetWork Set: Keep the default transparent mode.•  Socket A Connect Set: Congure the socket A  parameters, when connect with Carel BOSS system, the WiFi STA work as TCP Server and the port the 502. When in TCP-Server mode, ignore the Server IP Address.•  Socket B Connect Set: same as the socket A, default disabled.•  Save and Restart: when you congured the pages, you should save the changes. And you should restart the GTW after completing all settings.•  Connect With CAREL BOSS System: after congured the CAREL GTW as bellow congure:•  STA mode•  BOSS wireless SSID and password•  TCP server mode and 502 port•  check on ksa.carel.com in the boss section (FAQ) for all additional instruction needed to connect to the device to boss wi- network.First commissioning BLUETOOTH version•  Switch on you bluetooth device and look for the device “CAREL_GTW_SERIAL2BT_xxxxxx” (where xxxxxx are nal 3 bytes of MAC address)•  Connect to it;•  Open APPLICA app, check on ksa.carel.com for all additional les and istruction needed to connect to the device.Technical specificationsHardwarePower Supply 5…36VdcOperating  Current (internal WiFi module )Normal mode: Sleep mode:Deep dormancy:AP average: 74mA,  peak 285mASTA average: 32mA,  peak 196mA6.5mA90uAOper. Temperature -10…60°COperat. Humidity 5…95%RH (non-cond)Comm. Interface RS485, TTLWirelessWireless Standard 802.11 b/g/nTransmit power 802.11b: +18 +/-1dBm (@11Mbps CCK)802.11g: +17 +/-1dBm (@54Mbp OFDM)802.11n: +15 +/-1dBm (@HT20, MCS7)Receiving sensitivity802.11b: -85 dBm (@11Mbps CCK)802.11g: -70 dBm (@54Mbps OFDM)802.11n: -68 dBm (@HT20 MCS7)Antenna Antenna external rod antenna with a non-standard connectorSoftwareWireless Network TypesAP / STATIONWiFi Security WEP/WPA-PSK/WPA2-PSKWiFi Encryption TKIP, AES, TKIP/AESOperating frequency rangeBluetooth 2402-2480MHz - Max. tune-up power with tolerance -3±1.0dBmWiFi 2412-2462MHzMax. tune-up power with tolerance 11B:18±1dBm11G:17±1 dBm11N:15±1 dBmENGLISH VERSION / VERSIONE INGLESE

Navigation menu