Carpoint CP-X370 Car Navigation User Manual eManual XROAD370

Carpoint Co., Ltd. Car Navigation eManual XROAD370

USERS MANUAL

X-Road User’s ManualDescriptionUser’s Manual①Display : Points current position②Zoom in & out : Enlarge andreduce a scale, pressing + , -buttons③POP-UP Menu : Display & Hide④Message Ramp : Indicate the direction to turn right or left by following appropriate light⑤Destination : Destination Index①
FCC NOTICE THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITION: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDERSIRED OPERATION. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected. - Consult the dealer of an experienced radio/TV technician for help. NOTE : The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
1. Determine proper place to put on the front windshield.-Avoid the place that would interfere driving.-Wipe out the spot to put.3. Inhale the air after placing the arm.-After placing the transparent disk against the windshield, push the inhalation button.2. Adjust it to fix to the right direction against the driver’s view point.-Move the arm to the right angle for the driver.-Do not place X-Road right in front of the driver so that it cannot fell down to the driver in case of accident.-Do not try to fix while driving. -Wipe out the spot to place to keep it dropped.4. Connect cable to power from cigar jack.※Do not place cable into car-pack.5. Connect to the main system ※How to separate the main system-Push the main system until the basket operates to lock. -Pull the main system pushing the button on the basket.-The navigation system will automatically started putting power on.※Must inject cable to cigar jack after starting your car.Please place the main system after completion of setting the arm to the windshield. Otherwise the system would be hard to place or consequently be broken.Set UpSet Up
①Level of Map : Scalable from 1 to 9 level.②Direction :Arrow aims north.③Start/Stop Operation : To start operating navigation system and to stop it④Display of current location of the car : Points where you are.⑤Menu Bar : Choose menu.Map GuideScale up & downLevel of Map ScaleManu Bar GPS ConditionCurrent Location15m930m860m7120m6240m5600m42km34km215km1ScaleLevel of MapStart/Stop Op.
Menu BarHow to use -MENUInput destination by order of State->City ->Street->House using scroll bar or keypad under the screen①MAP : Display the destination ②My POI : Save destination in My POI ③GO : Start operation to the destination④Cancel : Go back to the previous stage< : erase<<, >> : movePoint out nearby places such as airports, banks, etc.POIRecord the mileage, speed, time of drivingTRIPBookmark of location (address) and point of interestMARKAddress/Intersection/POI/My POI/Route ListNAVIDestination/Route Manager/My POIManager/Settings/SimulationMENUFunctionMenuDestination Browse destination by addressMENU>>Destination>>Address
Input intersection by order of State->City ->Street->House using scroll bar or keypad under the screen.①MAP : Display the destination②My POI : Save destination in My POI③GO : Start operation to the intersection④Cancel : Go back to the previous stage< : erase<<, >> : moveHow to use –MENU How to use -MENUInformation of nearby points of interests from the nearest pointIndex : My POI / Exhibition / Airport / Ferry / Bank-Post / Fwy service / Car / Government /Church / Hospital / City Centre / Hotel / Museum / Restaurant / Park / Shopping /Sports / Petrol / Theatre / Police / Tourist info / Railway / Other…* POI : Point Of Interest DestinationDestination-Intersection-POIMENU>>Destination>>POI MENU>>Destination>>Intersection
How to use –MENU How to use -MENUList of the saved POI user bookmarkedShow the list by alphabetical order by using <<, >> button①Map : Display the destination from the list②GO : Start operation to the destination on the list③Cancel :Go back to the previous stageDestinationDestination-My POIMENU>>Destination>>My POI MENU>>Destination>>POIList of interest points user selects(ex. Airport)①MAP : Display the destination②My POI : Save destination in My POI③GO : Start operation to the destination④Cancel : Go back to the previous stage< : erase<<, >> : move-POI
How to use –MENU ComponentsDestinationMENU>>Destination>>Route List Show the list of routes on which user actually drove from the latest one (including S (Origin) / E (Destination))①MAP : Display the destination②Reserve Route : Start operation from the destination to the origin③Delete : Erase the record④Simulation : Test drive along the selected route⑤GO : Start operation to the destination⑥Cancel : Go back to the previous stage-Route ListMain System Arm Power Cable Compact Flash (256M)Data Cable Stylus Pen Fixing Pad for Data Cable User’s Manual
Setting Options for Routing①Route Method : Quickest / Shortest②Toll Roads : Include / Exclude③Freeway : Speed Detection Alarm Setting by Using <<, <, >, >> Button ④Highway : Speed Detection Alarm Setting by Using <<, <, >, >> Button⑤Main : Speed Detection Alarm Setting by Using <<, <, >, >> Button⑥Residential : Speed Detection Alarm Setting by Using <<, <, >, >> ButtonHow to use MENU How to use -MENUCurrent Route: Save and Erase recent record of driving①Erase : Erase the recent record of driving②Save : Save the recent record of driving.③Test : Test driving along the recent record of drivingRoute List: Display the origin and destination of recent driving. : Select Reverse Route, Delete, Simulation, GO, Point on the MapRoute ManagerRoute Manager-Route Option-Current Route/ -Route ListMENU>>Rute Manager>>Current Route/Route ListMENU>>Route Manager>>Route Option
Save or Delete My POI by choosing icons or rename①Save : Save or Modify POI②Rename : Save or Modify POI by using keypad③Cancel : Go back to the previous stageHow to use –MENU How to use -MENUInput POI by order of State->City ->Street->House using scroll bar or keypad under the screen①Map : Display the destination②My POI : Save the destination in My POI③GO : Start operation to the destination④Cancel : Go back to the previous stage< : erase<<, >> : moveMY POI Manager-Save PositionMY POI Manager-Save AddressMENU>>MY POI Manager>>Save Position MENU>>MY POI Manager>>Save Address
Modify or Delete the information on My POI①Del : Delete POI②Edit : Edit POI③Map : Position POI on the map④Cancel : Go back to the previous stageHow to use –MENU How to use -MENUSetting options of Display①Volume : Adjust volume for information②GPS Info : GPS Receiving Info. ③Speed Alert : Speed Alert on/off ④Display Options -Display Mode : Map/Text/Split-Map Mode : Heading up/North up/3D -Color : Auto/Day/Night-Auto Zoom in Guide : None/6-9 level -Auto Zoom at 80km/h : None/3-6 level-Auto Zoom at 40km/h : None/6-9 level⑤Map Labels : -POI Icon : on/off-POI Name : on/off-Street Name : on/offMY POI Manager-Edit My POISettingsMENU>>MY POI Manager>>Edit My POI MENU>>Settings
Test driving setting origin, destination, transit①Set Destination ②Start Destination③Set Transit④Test : Start Operation⑤Cancel : Go back to the previous stageHow to use –MENU How to use menu bar –NAVI, MARK, TRIP, POI①NAVI : Destination on MENU②MARK : MY POI Manager on MENU③TRIP : Reference of Driving record as shown in the picture on left (Speed, Distance, Time, etc.)④POI : POI on MENUSimulationMENU>>Simulation
Display sub-menu by pop-up screen on the map①Murry ST : Name of the street where you ARE②Set Destination : Point location on the map③Set Start Location : Point location on the map④Set Transit : Point location on the map⑤Save To My POI : Point location on the map⑥GO : Go to the destinationHow to use –MENU SimulationUse XROAD button on the bottom of the screenOperation Example –Screen DivisionCurrent PositionTime & Distance to DestinationNext turn : Direction/DistanceNext Turn : Direction/Distance/NameDriving/FinishName of the Street to Turn
Screen Selection (Viewer Mode)Setting Display[Map Mode] [Text Mode] [Split Mode]3 types of viewer mode while operation : Map/Text/Split Mode Setting : ①MENU>>Settings>>Display Options>>Display Mode ②Press [XROAD] button to change modeSetting display mode for the different environment or by the driver’s preference (MENU>>Settings>>Display Options>>Map Mode)[① Day Mode] [② Night Mode][③ Auto Mode] : Automatic transition from Day Mode to Night Mode and vice versa

Navigation menu