Carrier Access Bank Ii Snmp Users Manual Ab2snmp.bk

2015-02-05

• Access Bank II Cover
• FCC Requirements
• Safety Requirements
• National Electrical Code Requirements
• Industry Canada Requirements
• Warranty
• Warranty Product Returns
• Advice to the Reader
• How To Use This Manual
• Table of Contents
• Chapter 1 Introduction
  • 1.1 About This Chapter
  • 1.2 General System Overview
  • 1.3 Features, Functions, and Options
  • 1.4 Dual T1/CSU Network Interfaces
  • 1.5 Digital Data Ports
  • 1.6 Analog Line Interfaces: FXS, & FXO, and 4-Wire E&M
  • 1.7 Local and Remote Network Management
  • 1.8 Design Philosophy
• Chapter 2 Product Description
  • 2.1 About This Chapter
  • 2.2 Physical Characteristics
  • 2.3 Control Panel Interface Connectors
  • 2.4 Control Panel DIP Switches
  • 2.5 LED Test and Status Indicators
• Chapter 3 Technical Specifications
  • 3.1 About This Chapter
  • 3.2 Dual T1 Network Line Interfaces
  • 3.3 Line Codes
  • 3.4 Framing
  • 3.5 Clock Source
  • 3.6 T1-to-T1 Delay
  • 3.7 T1 Channel Service Units (CSUs)
  • 3.8 Digital Data Ports
  • 3.9 Analog Line Interfaces
  • 3.10 FXS Voice Card
  • 3.11 FXO/DPT Voice Card
  • 3.12 4-Wire E&M/TO Voice Card
  • 3.13 Network Management
  • 3.14 Alarms
  • 3.15 Control Panel I/O Connectors
  • 3.16 Standards Compliance
  • 3.17 Power
  • 3.18 Environmental
  • 3.19 Installation
• Chapter 4 Physical Installation
  • 4.1 About This Chapter
  • 4.2 Installation Check List
  • 4.3 Chassis Mounting
  • 4.4 Wall Mounting
  • 4.5 Rack Mounting
  • 4.6 Surface Mounting
  • 4.7 Mounting the Power Converter
• Chapter 5 Electrical Installation
  • 5.1 About This Chapter
  • 5.2 Installing Cables and Adapters
  • 5.3 Access Bank II SNMP Control Panel Interface and Power Connectors
  • 5.4 Connecting the Voice Circuits
  • 5.5 Connecting the Dual T1 Lines
  • 5.6 V.35 DCE Data Port Connections
  • 5.7 RS-232 Management
  • 5.8 Connecting the Power and Ground
• Chapter 6 Basic Configuration
  • 6.1 About This Chapter
  • 6.2 Connecting to the Access Bank
  • 6.3 Configuring the Access Bank
• Chapter 7 Remote Monitor
  • 7.1 About This Chapter
  • 7.2 Remote Monitor Software Program
  • 7.3 Message Traffic
  • 7.4 Online Help
  • 7.5 Hardware Requirements
  • 7.6 Installation
  • 7.7 Remote Monitor Screen Hierarchy
  • 7.8 Initialization for Basic Operation in the Remote Mode
• Chapter 8 FXS-ID Configuration
  • 8.1 About This Chapter
  • 8.2 FXS-ID Voice Card
  • 8.3 Signaling Types
  • 8.4 Setting the FXS Transmit and Receive Levels
  • 8.5 Setting the FXS Signaling Options
  • 8.6 FXS Signaling Option Descriptions
  • 8.7 FXS Voice Channel Monitoring and Testing
• Chapter 9 BRFXS & DPO
  • 9.1 About This Chapter
  • 9.2 Description of the BRFXS/DPO Card
  • 9.3 Overview of Operation
  • 9.4 BRFXS/DPO Applications
  • 9.5 Setting the Transmit and Receive Levels
  • 9.6 BRFXS/DPO Configuration Settings
  • 9.7 Setting BRFXS and DPO
  • 9.8 Busying Out Individual BRFXS/DPO Channels
  • 9.9 Self Test Loopbacks
• Chapter 10 12-Channel FXO & DPT
  • 10.1 About This Chapter
  • 10.2 Description of the FXO Card
  • 10.3 Termination Options
• Chapter 11 4-Wire E&M/TO
  • 11.1 About This Chapter
  • 11.2 4-Wire E&M/TO Voice Card
  • 11.3 Typical Applications
  • 11.4 E&M Signaling Conventions
  • 11.5 Programming E&M Signaling Types
  • 11.6 Detector Configuration
  • 11.7 Normal and Tandem Cables
  • 11.8 Configuring Signaling Types and Trunk Processing
  • 11.9 TP Busy/Idle Switch
  • 11.10 Setting Transmit and Receive Gain
  • 11.11 Transmit (Analog-to-Digital) Gain
  • 11.12 Receive (Digital-to-Analog) Gain
  • 11.13 E&M Voice Channel Monitoring
  • 11.14 E&M Normal mode cable
  • 11.15 E&M Tandem Mode Cable
• Chapter 12 Diagnostics & Troubleshooting
  • 12.1 About This Chapter
  • 12.2 Diagnostic Switches
  • 12.3 Self Test 1 and 2
  • 12.4 Self Test Fault Indications
  • 12.5 1 kHz Digital Milliwatt Test Signal
  • 12.6 Network Loopback 1 and 2
  • 12.7 Remote Mode: Remote T1 Line or Payload Loopbacks
  • 12.8 ANSI T1.403 Remote T1 LLB
  • 12.9 Illustrations of Loops and Self-Tests
  • 12.10 Disabling an External Alarm
  • 12.11 LED Test and Status Indicators
  • 12.12 Fault Isolation Procedures
  • 12.13 Back Plate Indications
  • 12.14 Other Fault Indications
  • 12.15 Access Bank II - SNMP Shuts Down for No Apparent Reason
• Chapter 13 Maintenance
  • 13.1 About This Chapter
  • 13.2 Replacing a Voice Card
  • 13.3 Replacing the Controller Card
• Chapter 14 SNMP Management & CLI
  • 14.1 About This Chapter
  • 14.2 Local/Remote Mode Selection
  • 14.3 SNMP Management
  • 14.4 Command Line Interface (CLI)
• Glossary