Carrier Outdoor Temperature Sensor Tstatccsen01 Users Manual

tstatccsen01 13ef757b-e13c-411f-8c28-bd0aa760c0ec Carrier Home Security System TSTATCCSEN01 User Guide |

: Carrier Carrier-Outdoor-Temperature-Sensor-Tstatccsen01-Users-Manual-310957 carrier-outdoor-temperature-sensor-tstatccsen01-users-manual-310957 carrier pdf

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

TSTATCCSEN01
Outdoor Temperature Sensor
Installation Instructions
NOTE: Read the entire instruction manual before starting the
installation.
SAFETY CONSIDERATIONS
Read and follow manufacturer instructions carefully. Follow all
local electrical codes during installation. All wiring must conform
to local and national electrical codes. Improper wiring or installation may damage thermostat sensor.
.
Recognize safety information. This is the safety-alert symbol
When you see this symbol on the equipment and in the instruction
manual, be alert to the potential for personal injury.
Understand the signal words DANGER, WARNING, and CAUTION. These words are used with the safety-alert symbol. DANGER identifies the most serious hazards which will result in severe
personal injury or death. WARNING signifies a hazard which
could result in personal injury or death. CAUTION is used to
identify unsafe practices which would result in minor personal
injury or product and property damage.

INTRODUCTION
The remote temperature sensor is an accessory for all Carrier
thermostats, except the non-programmable A/C versions. It allows
the temperature at a remote location to be displayed on the
thermostat.

PERFORMING THE INSTALLATION
Once the mounting location has been selected, route the interconnecting wiring through the building between thermostat and
outdoor sensor. The exit point from inside to outside will be the
location of the outdoor sensor. The location of the wire nuts will
be either inside or outside of wall depending on whether or not a
box is used. Allow sufficient wire length for some excess on each
end.
IF AN OUTLET BOX IS USED: (See Fig. 1.)
Drill a suitable hole in the building wall at selected sensor location.
Route interconnecting wire through building wall. Remove rear
knockout from electric box, route wire through box, and attach box
to wall with supplied wood screws.
Cut and strip wires to a reasonable length and connect with
supplied wire nuts. Polarity is unimportant. Seal wires where they
exit building with a suitable exterior caulk. Fasten cover to box
with supplied sheet metal screws.

FIELD-SUPPLIED
OUTLET BOX
SENSOR
EXTERIOR
WALL

MOUNTING CONSIDERATIONS
Choose a location for the outdoor sensor after considering the
following:
1) A wiring route must be planned between thermostat and
location of outdoor sensor, prior to installation.
2) A sensor located in direct sunlight will not read properly while
the sun is shining on it.
3) A high location under an eave is ideal because it is protected
from sun, weather, and people.
4) The sensor can be mounted directly to a wall using provided
screws and standoffs or can be used as a cover for a standard
electric outlet box (not supplied).
WIRING SELECTION:
A pair of conductors must be selected to run between mounted
sensor and thermostat. Conductors must be rated NEC Class 1.
Thermostat and common bell wire have this rating.

METAL
SCREWS

MOUNTING TO OUTLET BOX:
A standard electrical box (not included) may be used with the
sensor plate as its cover. This provides room inside box for wire
nut connection between sensor wires and wiring run to the
thermostat.

A94409

Fig. 1—Mounting to Outlet Box

USING SENSOR PLATE:
Attaching the plate directly to the outside wall simplifies mounting
and requires less space, but the wire nut transitions to the
thermostat wiring now need to be made within the wall. This may
be difficult in some installations.
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Book 1
4
PC 101
Catalog No. 92-33TS-TA13C
Printed in U.S.A.
Form TSTAT-3SI
Pg 1
12/15/94
Replaces: New
Tab misc. misc.

IF PLATE IS ATTACHED DIRECTLY TO WALL: (See Fig. 2.)
Drill a suitable hole through the wall at selected sensor location.
Route sensor wires through wall, making sure they are accessible
from the inside. Use provided spacers to stand off plate from wall.
Mount the sensor plate loosely to wall with only 1 screw so that
access to hole is preserved for application of caulking. Fill hole
with a suitable exterior caulking compound. Then insert second
screw and tighten both screws carefully.

SENSOR
SPACERS

EXTERIOR
WALL

From inside, locate sensor wires and wires from thermostat. Cut
and trim thermostat wires to an appropriate length and connect
with supplied wire nuts. It may be advisable to retain thermostat
wire with a clamp or wire staple ahead of wire nuts to prevent a
pull on this wire from damaging the more delicate sensor connections.
THERMOSTAT CONNECTION:
Turn OFF all power to system. The thermostat display will go
blank. Open thermostat at rear hinge to access connector blocks.
Route and connect wires at thermostat carefully to minimize
amount of wire between wall and thermostat. Strip ends only 1/4
in. to prevent a possible short between wires at the thermostat.
Attach wires to S1 and S2 terminals. Polarity is unimportant.
Route wires behind thermostat so that hinge can close properly.
When wiring is completed and thermostat closed, restore power to
system. Refer to Homeowners manual for procedure to display
remote temperature.

Copyright 1994 CARRIER Corp. • 7310 W. Morris St. • Indianapolis, IN 46231

WOOD SCREWS

Fig. 2—Mounting Directly to Wall

A94410

tstat3si

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Book 1
4
PC 101
Catalog No. 92-33TS-TA13C
Printed in U.S.A.
Form TSTAT-3SI
Pg 2
12/15/94
Replaces: New
Tab misc. misc.



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Creation Date--Text             : Tuesday, 31 January, 1995 at 09:47am
Producer                        : Acrobat Distiller 1.02 for Windows
Keywords                        : 
Format                          : application/pdf
Title                           : 
Description                     : 
Creator                         : Carrier Corporation
Subject                         : 
Modify Date                     : 2005:11:10 10:15:05-05:00
Create Date                     : 2005:11:10 10:15:05-05:00
Metadata Date                   : 2005:11:10 10:15:05-05:00
Document ID                     : uuid:16d86ace-e5e8-4986-b855-4550be92086e
Instance ID                     : uuid:c90714ec-1c7e-4469-9351-682ea7a3550d
Page Count                      : 2
Author                          : Carrier Corporation

EXIF Metadata provided by EXIF.tools