Casablanca Fan CASA3TA Ceiling fan and lamp remote control. User Manual S3 OMan Rev A 06

Casablanca Fan Company Inc Ceiling fan and lamp remote control. S3 OMan Rev A 06

Users Manual

8RemovingGently Pull the lower edgeof the control gently outfrom the holder.Control StorageAngle control in top first inthe holder until the unitcan be gently pushed backand snapped onto thebottom rim.WOODSCREW 1”Note: The wall anchors and6-32 x 1” screws may be usedin situations where mountingto a stud is not possible. Usethe inner mounting holes.After securing the anchor, dis-card the anchor’s pointedscrews and use the 6-32 de-cor ovalhead screws supplied.VERSA•TOUCH ♦ STORING CONTROL IN HOLDERDECOR OVALHEAD SCREW6-32 X 1”ANCHORPANHEADSCREW DRYWALL ANCHORTOP GOESIN FIRSTWall InstallationStep 1. Locate a2X4 wall stud in aconvenient loca-tion.Step 2. Orient thecontrol holder asshown over the2X4 stud.Step 3. Use the 1”wood screws in ei-ther the inner orouter mountingholes.Install and tight-en screws by handonly.ROCKERTYPELIGHTSWITCHSWITCHCOVERPLATESTANDARDTOGGLESWITCHSWITCHCOVERPLATEINNERMOUNTINGHOLESCONTROLHOLDEROUTERMOUNTINGHOLESSCREW6-32 X 1”(2)SCREW6-32 X 3/8”(2)WOODSCREW1”(2)DRYWALLANCHOR6-32(2)REMOVE TABSCAUTION! Do not use with wall dimmer.9V BATTERYW-42CONTROLRocker Light SwitchStep 1. Break off the two tabs by pushing outward.Step 2. Remove the two screws holding the switch cover plate. Donot remove the cover plate.Step 3. Orient the control holder as shown and line up the two outermounting holes with those on the switch.Step 4. Install and tighten screws by hand only.VERSA•TOUCH ♦ CONTROL HOLDER INSTALLATIONW-42CONTROLHOLDERVERSA•TOUCH ♦ INSTALLATIONStandard Light SwitchStep 1. Remove the two screws holding the switch coverplate. Do not remove the cover plate.Step 2. Orient the control holder as shown and line upthe two inner mounting holes with those on the switch.Step 3. Install and tighten screws by hand only.VERSA•TOUCH ♦ BATTERY INSTALLATION GUIDE SLOTSInstall BatteryPress battery intocontrol aligned asshown. Observeproper polarity.Replace thebattery door.SNAPSOCKET PLUGRemove Battery DoorTurn control on itsfront.Twist a coin to unsnapthe door A. Lift dooraway from control Band remove C.8RChanges or modifications not expressly approved in writing by Casablanca Fan Co. may voidthe user’s authority to operate this equipment.
9VERSA•TOUCH ♦ IF FAN DOES NOT WORKIf the fan is not functioning after installation:Step 1. Check to make sure that batteries are installed correctlyin the control.Step 2. Turn the power off to the fan (from the circuit breaker)for at least 5 seconds.Step 3. Turn the power back on (at the circuit breaker) and pushthe Hi, Med, and Low buttons–in that order–within 20 seconds.Step 4. The fan should now function properly.RSENDSIGNALLEDVERSA•TOUCH ♦ CHANGING FREQUENCY SETTINGVERSA•TOUCH OPERATIONFan ControlTo start the fan. Press the selected speed button to run the fan at the desired speed.LO Low speedMED Medium speedHI High speedTo turn off the fan. Press the FAN OFF button.Airflow DirectionTo reverse the airflow press the REVERSE button. Reverse operates at any speed whether fan ison or off. The fan returns to its set speed after reversing.Light ControlTurn the light on or off independently from the fan by pressing the LIGHT button. Keep pressingthe button in excess of 0.7 seconds, it becomes a dimmer. The light varies from ‘bright’ to ‘dim’over approximately 8 seconds. This sequence will reverse the light when it reaches the brightestor dimmest level if you continue to hold the LIGHT button. Release the button when thedesired level is reached.Auto ResumeQuick (pressing less than 0.7 seconds) on/off operation of the LIGHT button maintains thedesired brightness level set previously.You will only have to change the dip switch settings in the remote ifyou are using more than one fan in the same area and want to controlthem separately.Step 1. At the circuit breaker or fuse box, turn the power off for the fanyou want to change.Step 2. Open the battery door of the Versa•Touch control and removethe batteries.Step 3. Change the dip switch settings, assuring that they are differentfrom the previously installed Versa•Touch fan.Step 4. Re-install the batteries and the battery door on the control.Step 5. At the circuit breaker or fuse box, turn the power back on forthe fan whose frequency you are changing.Step 6. Within 20 seconds of restoring power, push the Hi, Med, and Lobuttons (in that order).9Note: All fans leave the factory set to ‘00000’.WITHIN 20 SECONDS OF TURNINGTHE FAN ON, PRESS IN THISORDER TO SET NEW FREQUENCY:1. HI2. MED3. LO123123CIRCUIT BREAKEROR FUSE BOXPRESS IN THIS ORDER TO SET NEWFREQUENCY:1. HI2. MED3. LODIP SWITCHSET TO ‘01001’DIP SWITCHSET TO ‘10000’VERSA•TOUCHCONTROL(BACK)Note: You may want to label your controls toassure you do not mix them up.WARNING: Do not turn the power off at the circuit breaker,then back on, for the previously installed Versa•Touch fan(s),as you may inadvertantly change the frequency settings forit as well.
10 10TROUBLESHOOTINGBefore Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance.Caring for Finishes: For cleaning, a soft brush or lint-free clothshould be used to prevent scratching the finish. A vacuum cleanerbrush nozzle can remove heavier dust. Surface smudges or an accu-mulation of dirt and dust can easily be removed by using a milddetergent and slightly dampened soft cloth. An antistatic agentmay be used, but never use abrasive cleaning agents. These willdamage the finish. Painted and high-gloss blades may be cleanedin the same manner.Blades: Wood finish blades should be cleaned with a furniture pol-ishing cloth. Occasionally, a light coat of furniture polish may beapplied for added protection and beauty.Never Lubricate this Fan!The precision motor at the heart of your Casablanca fan featuressealed bearings that are lubricated for life. Do not attempt to oilthe motor.Changing Light BulbsBe sure to turn power to the fan OFF at the wall switch or circuitbreaker before changing light bulbs. Replace bulbs with same typeas removed from the fixture. Each fan is rated for a maximum TOTALwattage of lighting.Exceeding the rated maximum allowable wattage for the fan willburn out the fan electronics module and void the warranty.PROBLEM POSSIBLE REMEDIES PROBLEM POSSIBLE REMEDIES..FAN WILL NOT START •Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, makingsure the power is turned off during this inspection.•Pin connectors are not making good contact. Check the connections in the switch housing and under thetop cover.•Battery weak - install fresh battery.•Fan receiver defective - replace.•Check the frequency setting: Turn power off, at the circuit breaker, only for the fan not functioning forat least 5 seconds; turn the power back on; within 20 seconds press the Hi, Med, and Lo buttons (in thatorder) to set the frequency of the fan to the control. See Page 9.FAN WOBBLES OR SHAKES •Be sure canopy pin is properly set into the slot on the ball.EXCESSIVELY •Check that bladeholders have not been bent during installation and blades are balanced.•Hanger bracket and/or ceiling outlet are loosely attached: Make sure that the hanger bracket is tightlyattached to the ceiling outlet box. Make sure that the downrod assembly is secured firmly•Downrod is loosely attached to downrod base: Make sure that all screws are securely tightenedFAN NOISY DURING •Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s).OPERATION •Tighten canopy screws and mounting plate assembly. Check that the wire nuts inside the canopy andswitch housing are not touching the metal parts or have fallen off the wire splices. Tighten as necessary.•Tighten blade holders to flywheel (or direct drive motor)/and blade to bladeholder screws.•Make sure all screws in the motor housing are snug, but not overly tight. Defective bulb: Replace bulb.DOES NOT RUN ON •If new, “break-in” may be required - run at higher speed for several days.LOW SPEEDBATTERY LIFE •Not using Alkaline batteries: Replace with Alkaline batteries.SEEMS SHORTVERSA•TOUCHLIGHT O.K., NO FAN: Pin connectors are not making good contact, check 9 pin connector under top cover. FAN O.K., NO LIGHT; Defectivereceiver; Replace receiver. Defective motor; Replace motor. Broken socket; Replace socket. Defective receiver; Replace Receiver. FAN ANDLIGHT ON FULL, NO CONTROL; Defective receiver; Replace Receiver. MISSING ONE SPEED: Defective receiver; ReplaceReceiver. FAN DOESN’TCHANGE SPEED, LIGHT O.K.: Replace receiver. FAN O.K., LIGHT NOT DIM: Defective receiver; Replace Receiver. NO REVERSE: Defectivereceiver; Replace Receiver. FAN OPERATES ONLY WHEN TRANSMITTER IS CLOSED: Check antenna wire is not touching metal plate. FANSTARTS WORKING BY ITSELF: Frequency interference; Change frequency as described on Page 9.1.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device may not cause harmful interference,and (2) this device must accept anyinterference received,including interference that may cause undesired operation.2.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may causeharmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures: Reorient orrelocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that to which the receiver is connected,Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’sauthority to operate this remote control.For questions or to locate the nearest Casablanca Authorized Service Center call toll free:1-888-227-2178 or visit us on the web at: www.CasablancaFanCo.com

Navigation menu