Casablanca Fan CASA5T Ceiling Fan and Lamp remote control User Manual Versa Touch Inst 5

Download:
Mirror Download [FCC.gov]
Document ID	151295
Application ID	Y1Zo/5r673jKcOGfO2UD2w==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	24.09kB (301153 bits)
Date Submitted	2001-05-23 00:00:00
Date Available	2001-05-23 00:00:00
Creation Date	2001-04-12 11:25:10
Producing Software	Acrobat Distiller 4.0 for Macintosh
Document Lastmod	2001-04-23 08:29:54
Document Title	Versa Touch Inst 5
Document Creator	Adobe PageMaker 6.52
Document Author:	Patrick D. Giever, Media Director

VERSA•TOUCH ♦ INSTALLATION
W-42
W-43
CONTROL
HOLDER
W-43
CONTROL
DRYWALL
ANCHOR
6-32 (2)
9V BATTERY
WOOD
SCREW
1” (2)
SCREW
6-32 X 3/8”
(2)
SCREW
6-32 X 1”
(2)
VERSA•TOUCH ♦ CONTROL HOLDER INSTALLATION
CAUTION! DO NOT USE WITH WALL DIMMER.
STANDARD
TOGGLE
SWITCH
INNER
MOUNTING
HOLES
REMOVE TABS
ROCKER
TYPE
LIGHT
SWITCH
OUTER
MOUNTING
HOLES
SWITCH
COVER
PLATE
SWITCH
COVER
PLATE
CONTROL
HOLDER
Standard Light Switch
Step 1. Remove the two screws holding the switch cover
plate. Do not remove the cover plate.
Step 2. Orient the control holder as shown and line up the
two inner mounting holes with those on the switch.
Step 3. Install and tighten screws by hand only.
Rocker Light Switch
Step 1. Break off the two tabs by pushing outward.
Step 2. Remove the two screws holding the switch cover plate.
Do not remove the cover plate.
Step 3. Orient the control holder as shown and line up the two
outer mounting holes with those on the switch.
Step 4. Install and tighten screws by hand only.
VERSA•TOUCH ♦ HOLDER INSTALLATION / STORAGE
Wall Installation
Step 1. Locate a
2x4 wall stud in a
convenient location.
Step 2. Orient the
control holder as
shown over the
2x4 stud.
Step 3. Use the 1"
wood screws in either the inner or
outer mounting
holes. Install and
tighten screws by
hand only.
Note: The wall anchors and
6-32 x 1” screws may be used in
situations where mounting to a
stud is not possible. Use the inner
mounting holes. After securing the
anchor, discard the anchor’s
pointed screws and use the 6-32
decor ovalhead screws supplied.
Control Storage
Angle control in top first
until the unit can be
gently pushed back and
snapped into place.
TOP
GOES IN
FIRST
WOOD
SCREW 1”
ANCHOR
PANHEAD
SCREW
DRYWALL ANCHOR
DECOR OVALHEAD SCREW
6-32 X 1”
Removing Control
Gently Pull the lower edge
of the control out from the
holder.
VERSA•TOUCH ♦ BATTERY INSTALLATION
Remove Battery Door
Turn control on its front.
Twist a coin to unsnap
the door A. Lift door
away from control B and
remove C.
Changes or modifications not expressly approved in writing by Casablanca Fan Co. may
void the user’s authority to operate this
equipment.
©2001 Casablanca Fan Co.
SNAP PLUG
SOCKET
Install Battery
Press battery into
control aligned as
shown. Observe proper
polarity. Replace the
battery door.
GUIDE SLOTS
This device complies with RSS-210 of Industry Canada. Operation is subject to
the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
www.CasablancaFanCo.com
VERSA•TOUCH OPERATION
Fan Control
To start the fan. Press the selected speed button to run the fan at the desired speed.
LO=Low speed MED=Medium speed HI=High speed
To turn off the fan. Press the FAN OFF button.
Airflow Direction
To reverse the airflow press the REVERSE button. Reverse operates at any speed whether fan is
on or off. The fan returns to its set speed after reversing.
Light Control
Turn the light on or off independently from the fan by pressing the UP LIGHT, DOWN LIGHT,
OR BOTH button. (This is a rocker switch. Press the left side for the Up Light, right side for the
Down Light, and the middle for both.) Keep pressing the button in excess of 0.7 seconds, it
becomes a dimmer. The light varies from ‘bright’ to ‘dim’ over approximately 8 seconds. This
sequence will reverse the light when it reaches the brightest or dimmest level if you continue
to hold the LIGHT button. Release the button when the desired level is reached.
Auto Resume
Quick (pressing less than 0.7 seconds) on/off operation of the LIGHT button maintains the
desired brightness level set previously.
SEND SIGNAL
LED
VERSA•TOUCH ♦ CHANGING FREQUENCY SETTING
VERSA•TOUCH
CONTROL
(BACK)
Note: All fans leave the factory set to ‘00000’.
You will only have to change the dip switch settings in the remote if
you are using more than one fan in the same area and want to control
them separately.
Step 1. At the circuit breaker or fuse box, turn the power off for the fan
you want to change.
Step 2. Open the battery door of the Versa•Touch control and remove
the batteries.
Step 3. Change the dip switch settings, assuring that they are different
from the previously installed Versa•Touch fan.
Step 4. Re-install the batteries and the battery door on the control.
Step 5. At the circuit breaker or fuse box, turn the power back on for
the fan whose frequency you are changing.
DIP SWITCH
SET TO ‘10000’
DIP SWITCH
SET TO ‘01001’
Step 6. Within 20 seconds of restoring power, push the Hi, Med, and Lo
buttons (in that order).
Note: You may want to label your controls to
assure you do not mix them up.
WITHIN 20 SECONDS OF TURNING
THE FAN ON, PRESS IN THIS
ORDER TO SET NEW FREQUENCY:
1. HI
2. MED
3. LO
WARNING: Do not turn the power off at the circuit breaker,
then back on, for the previously installed Versa•Touch fan(s),
as you may inadvertantly change the frequency settings for
it as well.
VERSA•TOUCH ♦ IF FAN DOES NOT WORK
If the fan is not functioning after installation:
Step 1. Check to make sure that batteries are installed correctly
in the control.
Step 2. Turn the power off to the fan (from the circuit breaker)
for at least 5 seconds.
Step 3. Turn the power back on (at the circuit breaker) and push
the Hi, Med, and Low buttons–in that order–within 20 seconds.
Step 4. The fan should now function properly.
©2001 Casablanca Fan Co.
CIRCUIT BREAKER
OR FUSE BOX
www.CasablancaFanCo.com
PRESS IN THIS ORDER TO SET NEW
FREQUENCY:
1. HI
2. MED
3. LO
TROUBLESHOOTING
VERSA•TOUCH
PROBLEM
PROBLEM
POSSIBLE
POSSIBLE REMEDIES
REMEDIES..
Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance.
FAN WILL NOT START
•Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making
sure the power is turned off during this inspection.
•Pin connectors are not making good contact. Check the connections in the switch housing and under the
top cover.
•Battery weak - install fresh battery.
•Fan receiver defective - replace.
•Check the frequency setting: Turn power off, at the circuit breaker, only for the fan not functioning for
at least 5 seconds; turn the power back on; within 20 seconds press the Hi, Med, and Lo buttons (in that
order) to set the frequency of the fan to the control. See Page 9.
FAN WOBBLES OR SHAKES •Be sure canopy pin is properly set into the slot on the ball.
EXCESSIVELY
•Check that bladeholders have not been bent during installation and blades are balanced.
•Hanger bracket and/or ceiling outlet are loosely attached: Make sure that the hanger bracket is tightly
attached to the ceiling outlet box. Make sure that the downrod assembly is secured firmly
•Downrod is loosely attached to downrod base: Make sure that all screws are securely tightened
FAN NOISY DURING
OPERATION
•Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s).
•Tighten canopy screws and mounting plate assembly. Check that the wire nuts inside the canopy and
switch housing are not touching the metal parts or have fallen off the wire splices. Tighten as necessary.
•Tighten blade holders to flywheel (or direct drive motor)/and blade to bladeholder screws.
•Make sure all screws in the motor housing are snug, but not overly tight. Defective bulb: Replace bulb.
DOES NOT RUN ON
LOW SPEED
•If new, “break-in” may be required - run at higher speed for several days.
BATTERY LIFE
SEEMS SHORT
•Not using Alkaline batteries: Replace with Alkaline batteries.
• LIGHT O.K., NO FAN: Pin connectors are not making good contact, check 9 pin connector under top cover.
• FAN O.K., NO LIGHT; Defective receiver; Replace receiver. Defective motor; Replace motor. Broken socket; Replace socket. Defective receiver;
Replace Receiver.
• FAN AND LIGHT ON FULL, NO CONTROL; Defective receiver; Replace Receiver.
• MISSING ONE SPEED: Defective receiver; ReplaceReceiver.
• FAN DOESN’T CHANGE SPEED, LIGHT O.K.: Replace receiver.
• FAN O.K., LIGHT NOT DIM: Defective receiver; Replace Receiver.
• NO REVERSE: Defective receiver; Replace Receiver.
• FAN OPERATES ONLY WHEN TRANSMITTER IS CLOSED: Check antenna wire is not touching metal plate.
• FAN STARTS WORKING BY ITSELF: Frequency interference; Change frequency as described on Page 9.
For questions or to locate the nearest Casablanca Authorized Service Center call toll free:
1-888-227-2178 or visit us on the web at: www.CasablancaFanCo.com
1.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device may not cause harmful interference,and (2) this device must accept any
interference received,including interference that may cause undesired operation.
2.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may cause
harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or
relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that to which the receiver is connected,
Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s
authority to operate this remote control.
©2001 Casablanca Fan Co.
www.CasablancaFanCo.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2001:04:12 11:25:10
Producer                        : Acrobat Distiller 4.0 for Macintosh
Subject                         : Versa Touch Inst 5
Creator                         : Adobe PageMaker 6.52
Title                           : Versa Touch Inst 5
Author                          : Patrick D. Giever,  Media Director
Modify Date                     : 2001:04:23 08:29:54-05:00
Page Count                      : 3

EXIF Metadata provided by EXIF.tools