Casio Computer DTX5 Handheld Terminal User Manual

Casio Computer Co Ltd Handheld Terminal

Manual rev

Handheld TerminalESeriesUser’s GuideBe sure to read “Safety Precautions” inside this guide before trying to use your Handheld Terminal. After reading this guide, keep it in a safe place for future reference.DT-X5PN410388-002DT-X5_E_Hyo_1_4.p65 2004.10.1, 9:52 AM3
•This product includes BRYCEN Co., Ltd’ s B-RAPPORE Stack, which use is governedby a licence granted by BRYCEN Co., Ltd.•BLUETOOTH is a trademark owned by Bluetooth SIG, Inc. and licensed to CASIOCOMPUTER CO., LTD.•Microsoft and Windows are either registered trademarks or trademarks of MicrosoftCorporation in the United States and/or other countries.•Datalight is a registered trademark of Datalight, Inc.•FlashFXTM is a trademark of Datalight, Inc.Copyright 1993-2000 Datalight, Inc., All Rights Reserved.U.S. Patent Office 5,860,082•Other company names and product names used in this guide are trademarks or registeredtrademarks of their respective owners.DT-X5_E_P00.p65 2004.10.1, 9:46 AM2
E-1WarningCautionDangerSafety PrecautionsCongratulations upon your selection of this CASIO product. Be sure to read thefollowing Safety Precautions before trying to use it for the first time.Markings and SymbolsThe following are the meanings of the markings and symbols used in these SafetyPrecautions.This symbol indicates information that, if ignored or appliedincorrectly, creates the danger of death or serious personal injury.This symbol indicates information that, if ignored or appliedincorrectly, creates the possibility of death or serious personalinjury.This symbol indicates information that, if ignored or appliedincorrectly, creates the possibility of personal injury or propertydamage.•A diagonal line indicates something you should not do. The symbol shownhere indicates you should not try to take the unit apart.•A black circle indicates something you should do. The symbol shown hereindicates you should unplug the unit from the wall outlet.Precautions During UseWarningDisassembly and Modification•Never try to disassemble or modify the Handheld Terminal and its options inany way. High voltage inside creates the danger of electric shock.Abnormal Conditions•Should the Handheld Terminal and its options become hot or start to emitsmoke or a strange odor, immediately turn off the power, and contact youroriginal vendor or an authorized CASIO service provider. Continued usecreates the danger of fire and electric shock.DT-X5_E_P01_10.p65 2004.10.1, 9:47 AM1
E-2Safety PrecautionsWarningForeign Objects•Should any foreign matter get into the Handheld Terminal and its options,immediately turn off the power and contact your original vendor or anauthorized CASIO service provider. Continued use creates the danger of fireand electric shock.Dropping and Damage•Should you drop the Handheld Terminal and its options and damage them,immediately turn off the power and contact your original vendor or anauthorized CASIO service provider. Continued use creates the danger of fireand electric shock.Moisture•Though your Handheld Terminal is water splash-resistant, its Cradle andother optional peripherals are not. Keep loose metal objects and containersfilled with liquids away from your Handheld Terminal and the optionalperipherals.Also, never connect or disconnect peripherals to the Handheld Terminalwhile they are wet. Water getting into the Handheld Terminal or itsperipherals creates the danger of fire and electric shock.Laser Light•This product scans bar codes using laser light. Never look directly into thelaser light or shine the laser light into the eyes.DT-X5_E_P01_10.p65 2004.10.1, 9:47 AM2
E-3CautionForeign Objects•Take care to ensure that metals or combustible objects are not inserted intothe openings of the Handheld Terminal and its options. Such the objectsinside of the Handheld Terminal and its options create the danger of fire andelectric shock.Location•Do not locate the Handheld Terminal and its options on a surface that isunstable or uneven. Doing so creates the danger of the Handheld Terminalfalling, which can cause personal injury.•Do not locate the Handheld Terminal and its options in an area subject tolarge amounts of humidity or dust. Doing so creates the danger of fire andelectric shock.•Do not leave the Handheld Terminal and its options for a long period in a carparked in direct sunlight.Heavy Objects•Never place heavy objects on top of the Handheld Terminal and its options.Doing so creates the danger of loss of balance and the objects falling, whichcan cause personal injury.LCD Screen•Should the LCD panel glass break, never touch the liquid inside. Doing socan cause skin inflammation.– Should liquid from the LCD panel accidentally get into your mouth,immediately wash your mouth with water and then consult a physician.– Should liquid from the LCD panel accidentally get into your eyes or ontoyour skin, immediately rinse for at least 15 minutes with clean tap waterand then consult a physician.DT-X5_E_P01_10.p65 2004.10.1, 9:47 AM3
E-4Safety PrecautionsThis wireless transmitter uses the 2.4 GHz band. It employs the FH-SSmodulation system and has an interfering range of 20 m.This wireless transmitter uses the 2.4 GHz band. It employs the DS-SSmodulation system and has an interfering range of 40 m.Operation of Wireless Data Communication FunctionWarningInterference with the Operation of Other Equipment(Using Wireless Data Communication Function)•Please follow the instructions provided by health care facilities when usingyour Handheld Terminal in hospitals or other locations where medicalequipment is in use. In particular, either switch off the wireless datacommunication function of the Handheld Terminal or turn off the power inlocations such as operating rooms, intensive care units, coronary arterydisease monitoring units and other locations where use of the HandheldTerminal is prohibited by the health care facility. Radio waves emitted bythe Handheld Terminal can affect the operation of medical equipment.•Keep your Handheld Terminal at least 22 centimeters (85/8") away fromanyone wearing a pacemaker. Radio waves emitted by the HandheldTerminal can affect the operation of a pacemaker.•The use of wireless communication devices and electronic devices isprohibited by airlines depending on the flight status of the aircraft. Switch offthe wireless data communication function of the Handheld Terminal whileonboard an aircraft. Use of the Handheld Terminal can affect electronicdevices used by the aircraft potentially causing a malfunction or accident.CautionInterference with the Operation of Other Equipment(Using Wireless Data Communication Function)The Handheld Terminal contains a built-in wireless communication device of a low-powerdata communication system. The frequency band that is used is also used by microwave ovensand other industrial, scientific and medical devices, as well as other wireless stations of thesame type, local wireless stations for identifying moving objects requiring licensing used onfactory production lines and so forth, specified low-power wireless stations not requiringlicensing, and amateur wireless stations (to be referred to as “other wireless stations”).•Confirm that other wireless stations are not in use nearby before using theHandheld Terminal.•In the case radio wave interference has been generated between the Handheld Terminaland other wireless stations, either promptly change the location where the HandheldTerminal is used or discontinue operation of the equipment causing the interference.•If other problems should occur as a result of the generation of radio wave interference,please contact the location indicated in the section on product consultations.(DT-X5M10R/DT-X5M30R/DT-X5M30UR)DT-X5_E_P01_10.p65 2004.10.1, 9:47 AM4
E-5Alkaline Battery Handling PrecautionsDanger•Since there is the risk of blindness and other serious disorders when alkalinebattery fluid enters the eyes, seek medical treatment immediately afteradequately flushing the eyes with a large amount of tap water or other cleanwater without rubbing.Warning•Do not dispose of batteries in open flames or allow them to be heated,disassembled or modified. This results in the risk of damaging insulationand safety valves or causes the batteries to leak fluid, overheat or rupture.•Do not reverse the (+) and (–) poles of the batteries. This results in the riskof abnormal reactions during charging or short-circuiting, or causes thebatteries to leak fluid, overheating or rupture.•Store batteries in a location out of the reach of small children. In the case abattery should happen to be swallowed, seek medical treatment immediately.•In the case of having ingested alkaline battery fluid, gargle immediately andseek medical treatment.•Since there is the risk of injury to the skin in the case alkaline battery fluidhas come in contact with the skin or clothing, immediately rinse off with alarge amount of tap water or other clean water.•Do not allow the (+) and (–) poles of alkaline batteries to come in contactwith wires or other metal objects, and do not carry or store them togetherwith metal necklaces, hair pins and so on. This results in the risk of thebatteries short-circuiting resulting in the flow of excess current and causingthe batteries to leak fluid, overheat or rupture.•Do not use a new battery with an old battery that has already been used oruse different types of batteries. Differences in properties results in the riskof the batteries leaking fluid, overheating or rupturing.•These batteries are not designed to be recharged. Recharging results in therisk of damage to insulation and internal structure causing the batteries toleak fluid, overheat or rupture.•Do not remove or damage the battery outer label. This results in the risk ofthe batteries short-circuiting, leaking fluid, overheating or rupturing.•Do not subject the batteries to strong impacts resulting from dropping or throwing.This results in the risk of the batteries leaking fluid, overheating or rupturing.•Do not allow the batteries to be deformed or damaged. This results in therisk of damage to the insulation and safety valve causing the batteries toleak fluid, overheat or rupture.DT-X5_E_P01_10.p65 2004.10.1, 9:47 AM5
E-6Safety PrecautionsCaution•Promptly remove worn out batteries from the Handheld Terminal. Allowingworn out batteries to remain installed in the Handheld Terminal for a longperiod of time results in the risk of the generation of gas from the batteriescausing the batteries to leak fluid, overheat or rupture.•Remove the batteries from the Handheld Terminal when not using for a longperiod of time. Failure to do so results in the risk of the generation of gasfrom the batteries causing the batteries to leak fluid and damage theHandheld Terminal.•Do not attempt to solder the batteries directly. This results in the risk of heatdamaging the insulation and safety valve causing the batteries to leak fluid,overheat or rupture.•Do not use or place the batteries in a location subject to high temperaturessuch as locations of intense direct sunlight or in an automobile on a hot day.This results in the risk of the batteries leaking fluid, overheating orrupturing.•Insulate the ends of the batteries by covering with tape and so on whenstoring or disposing. Allowing the batteries to contact other batteries ormetal objects results in the risk of the batteries leaking fluid, overheating orrupturing.•Do not allow the batteries to become wet. This results in the risk of thebatteries overheating.•Avoid storing batteries in locations subject to direct sunlight, hightemperature or high humidity. This results in the risk of the batteries leakingfluid. In addition, there is also the risk of reduced battery performance andshorter battery life.•Although these batteries may be disposed of in the same manner as ordinarynon-burnable garbage, please dispose of them in the proper manner inaccordance with the rules and regulations of your local community whenapplicable.DT-X5_E_P01_10.p65 2004.10.1, 9:47 AM6
E-7Optional Lithium-ion Battery PackDanger•Never allow the battery pack to become wet. Water can create the danger ofbattery pack heat emission, explosion, and fire.•Never use or leave the battery pack next to open flame, near a stove, or anyother area exposed to high heat. Doing so creates the danger of battery packheat emission, explosion, and fire.•Never use the battery pack with any device other than the HandheldTerminal. Doing so can create the danger of battery pack heat emission,explosion, and fire.•Note that the battery pack’s positive (+) and negative (–) polarities must beoriented correctly when it is loaded into battery charger or the HandheldTerminal. Connecting the battery pack with its polarities reversed creates thedanger of battery pack fluid leakage, heat emission, explosion, and fire.•Never dispose of the battery pack by incinerating it or otherwise expose it toheat. Doing so creates the danger of battery pack heat emission, explosion,and fire.•Never allow the positive (+) and negative (–) terminals of the battery pack tobecome connected (shorted) by metal. Doing so creates the danger of batterypack heat emission, explosion, and fire.•Never transport or store the battery pack together with a necklace, hair pinsor other metal objects. Doing so can short battery pack terminals, creatingthe danger of battery pack heat emission, explosion, and fire. Be sure toplace the battery pack in its case whenever transporting or storing it.•Never throw the battery pack or otherwise subject it to strong impact. Doingso creates the danger of battery pack heat emission, explosion, and fire.•Never pierce the battery pack with nails, hit it with a hammer, or step on it.Doing so can create the danger of battery pack heat emission, explosion, andfire.•Never try to take apart the battery pack or modify it in any way. Doing socreates the danger of battery pack heat emission, explosion, and fire.•Use only the specified battery charger to charge the battery pack. Use ofother type of battery charger creates the danger of battery pack heatemission, explosion, and fire.DT-X5_E_P01_10.p65 2004.10.1, 9:47 AM7
E-8Safety PrecautionsWarning•Never place the battery pack in a microwave oven or any other high-voltagedevice. Doing so creates the danger of battery pack heat emission,explosion, and fire.•Should the battery pack emit a strange odor or heat, change color or shape,or exhibit any other abnormal behavior, immediately stop using it.Continued use creates the danger of battery pack heat emission, explosion,and fire.•If the battery pack does not achieve full charge after the normal chargingtime has passed, stop charging it. Continued charging creates the danger ofbattery pack heat emission, explosion, and fire.•Should the battery pack start to leak or emit a strange odor, immediatelymove it away from flame. Leaking battery fluid is combustible, andexposure to flame creates the danger of explosion and fire.•Should fluid from the battery pack accidentally get into your eyes, do notrub them. Immediately rinse your eyes with clean tap water and then consulta physician immediately.Caution•Never use or leave the battery pack in an area exposed to direct sunlight, ina car parked in direct sunlight, or any other very hot area. Doing so createsthe danger of heat emission and fire, as well as deterioration of battery packperformance and shortening of its service life.•Do not use the battery pack in areas where static electricity is beinggenerated. Doing so creates the danger of battery pack heat emission,explosion, and fire.•Danger of explosion if the battery pack is incorrectly replaced.Replace only with same or equivalent type recommended by CASIO.Dispose of used batteries according to the CASIO instruction.•Should fluid from the battery pack accidentally get onto clothing or yourskin, immediately rinse it off with clean tap water. Prolonged contact withbattery pack fluid can cause skin irritation.•Keep the battery pack out of the reach of small children. Do not let smallchildren remove the battery pack from battery charger or the HandheldTerminal while it is powered on.DT-X5_E_P01_10.p65 2004.10.1, 9:47 AM8
E-9AC Power SupplyWarning•Do not use the Handheld Terminal at a voltage other than the specifiedvoltage. Also, do not connect the Handheld Terminal to a multi-plug powerstrip. Doing so creates the danger of fire and electric shock.•Avoid conditions that can cause damage or breaks in the power cord. Do notplace heavy objects on the power cord and keep it away from sources ofheat. Any of these conditions can damage the power cord, creating thedanger of fire and electric shock.•Never modify, sharply bend, twist, or pull on the power cord. Doing socreates the danger of fire and electric shock.•When using the battery charger, Cradle and Dual Battery Charger, be sure touse the respective AC adaptors. Use of other types of AC adaptors createsthe danger of fire and electric shock.•Should the power cord become severely damaged (to the point that wires areexposed or broken), contact your original vendor or an authorized CASIOservice provider about repair or replacement. Use of a damaged electricalcord creates the danger of fire and electric shock.Caution•Keep the power cord away from stoves and other sources of extreme heat.Heat can melt the covering of the power cord and create the danger of fireand electric shock.•Never pull on the power cord when unplugging it. Doing so can damage thecord and create the danger of fire and electric shock. (Always hold the plugwhen unplugging it from the wall outlet.)•Never touch the plug while your hands are wet. Doing so can create thedanger of electric shock.•Be sure to unplug the power cord from the wall outlet before moving thebattery charger, Cradle and Dual Battery Charger. Failure to do so can resultin damage to the power cord caused by pulling it, which creates the dangerof fire and electric shock.•Be sure to unplug the power cord from the wall outlet before cleaning thebattery charger and Cradle.•Be sure to turn the power off and unplug the power cord after use.•Unplug the power cord from the wall outlet whenever leaving the battery charger,Cradle and Dual Battery Charger unattended for a long period of time.DT-X5_E_P01_10.p65 2004.10.1, 9:47 AM9
E-10Safety PrecautionsAC AdaptorCaution•The housing of the AC adaptor can become warm during normal use.•Take normal precautions against electric shock.•At least once a year, unplug the AC adaptor from the wall outlet and cleanany dust that builds up between the prongs of the plug.Dust built up between the prongs can lead to the danger of fire.Backup Copies of All Important DataCaution•Note that CASIO Computer Co., Ltd. shall not be held liable to you or anythird party for any damages or loss caused by deletion or corruption of datadue to use of the Handheld Terminal, malfunction or repair of the HandheldTerminal or its peripherals, or due to the batteries going dead.•The Handheld Terminal employs electronic memory to store data, whichmeans that memory contents can be corrupted or deleted if power isinterrupted due to the batteries going dead or incorrect battery replacementprocedures. Data cannot be recovered once it is lost or corrupted. Be sure tomake backup copies of all important data.DT-X5_E_P01_10.p65 2004.10.1, 9:47 AM10
E-11Operating PrecautionsYour Handheld Terminal and its options are precision digital instruments. Improperoperation or rough handling can cause problems with data storage and other problems.Note and observe the following precautions to ensure proper operation.•Do not continue operating the Handheld Terminal when battery power is low.Doing so can cause data to be lost or altered. If the batteries become worn down,either promptly replace them with new AA size alkaline batteries or charge the batterypack.•Do not leave dead batteries in the Handheld Terminal for a long period.Dead batteries can leak, leading to malfunction and damage to the Handheld Terminal.•Use the Handheld Terminal and its options only within the specified temperaturerange.Use outside of the specified temperature range creates the risk of malfunction.•Avoid using the Handheld Terminal and its options in areas subject to thefollowing conditions.Doing so can damage the Handheld Terminal or cause it to malfunction.— Large amounts of static electricity— Extreme heat or extreme cold— High humidity— Sudden temperature extremes— Large amounts of dust•Never use thinner, benzene, cosmetic cleaning fluids, or other volatile agents toclean the Handheld Terminal.To clean the Handheld Terminal, wipe it with a dry cloth or cloth moistened withneutral detergent diluted with water. Wring all excess moisture from the clothbefore wiping.DT-X5_E_P11_15.p65 2004.10.1, 9:47 AM11
E-12Important•The contents of this guide are subject to change without notice.•Note that CASIO COMPUTER CO., LTD. shall not be held liable to you or any thirdparties for any losses or damages arising from the use of this guide.•Although the utmost care has been taken in preparing this manual, please contact themanufacturer if you should happen to notice any inconsistencies or errors.•This guide does not include any information about programming and downloadprocedures. See the applicable separate documentation for information about theprocedures.Warranty and After Service•Should this product ever malfunction, contact your original retailer providinginformation about the product name, the date you purchased it, and details about theproblem.DT-X5_E_P11_15.p65 2004.10.1, 9:47 AM12
E-13IMPORTANT NOTE:FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolledenvironment. This device complies with FCC RF Exposure limits set forth for anuncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2).This transmitter must not be co-located or operating in conjunction with any otherantenna or transmitter.
E-14Product description / Intended useEU/EFTA member states intended for use EU: Austria, Belgium, Denmark, Finland, France,Germany, Greece, Ireland, Italy, Luxembourg, TheNetherlands, Portugal, Spain, Sweden, United KingdomEFTA: Switzerland, Iceland, Lichtenstein, NorwayMember states with restrictive use NONEManufacturer CASIO COMPUTER CO., LTD.Brand CASIOType DT-X5M10E, DT-X5M10R, DT-X5M30E,DT-X5M30R, DT-X5M30U, DT-X5M30UR,are tested and found to conform with the essential requirements for protection of health and the safety of theuser and any other persons and Electromagnetic Compatibility, as included in following standards:Standard lssue dateEN60950:2000 2002-02EN301 489-1, 2002-08EN301 489-17 2002-08and are tested and found to conform with the essential radio test suites so that they effectively use thefrequency spectrum allocated to terrestrial/space radio communication and orbital resources so to as toavoid harmful interference, as included in following standards:DT-X5M10E;Standard lssue dateEN300 328-1 2001-12EN300 328-2 2001-12and therefore comply with the essential requirements and provisions of the Directive 1999/5/EC of theEuropean Parliament and of the council of March 9, 1999 on Radio equipment and TelecommunicationsTerminal Equipment and the mutual recognition of their conformity and with the provisions of Annex III(Conformity Assessment procedure referred to in article 10).DT-X5M10R;Standard lssue dateEN300 328-1 2001-12EN300 328-2 2001-12EN50360 2001-07EN50361 2001-09and therefore comply with the essential requirements and provisions of the Directive 1999/5/EC of theEuropean Parliament and of the council of March 9, 1999 on Radio equipment and TelecommunicationsTerminal Equipment and the mutual recognition of their conformity and with the provisions of Annex IV(Conformity Assessment procedure referred to in article 10).certify and declare under our sole responsibility that the following equipments:ImportantWe, the undersigned.Company CASIO Europe GmbHAddress, City Bornbarch 10, D-22848 NorderstedtCountry GermanyPhone number +49(0)40-528-65-0Fax number +49(0)40-528-65-424DT-X5_E_P11_15.p65 2004.10.1, 9:47 AM14
E-15Products are for distribution within all member states of the EU.DT-X5M10E/DT-X5M30E/DT-X5M30U; DT-X5M10R/DT-X5M30R/DT-X5M30UR;The folowing Notified Body has been consulted in the Conformity Assessment procedure.Notified Body number Name and Address0560 TELEFICATION B.V., Utrechtseweg 310 - P.O. Box 60004,NL-6800 JA ARNHEM, The NetherlandsThe technical documentation as required by the Conformity Assessment procedure is kept at the followingaddress:Company CASIO Europe GmbHAddress, City Bornbarch 10, D-22848 NorderstedtCountry GermanyPhone number +49(0)40-528-65-0Fax number +49(0)40-528-65-42405600560The information described above dates from May 2004 and maybe subjected to future changes.DT-X5_E_P11_15.p65 2004.10.1, 9:47 AM15
E-16ContentsSafety Precautions ............................................................................................ 1Operating Precautions .................................................................................... 11Important .......................................................................................................... 12Warranty and After Service ........................................................................... 12Before Getting Started .................................................................................... 18When unpacking, make sure that all items are included. ............................. 18Install the main battery. ................................................................................. 19When Using the AA size Alkaline Batteries ......................................................... 19When Using the Battery Pack ............................................................................... 20Turning On the Power ................................................................................... 21Handheld Terminal System Configuration .................................................... 22General Guede ................................................................................................. 25Replacing the Battery ..................................................................................... 27Replacing the Battery Pack .......................................................................... 27Replacing the AA size Alkaline Batteries ............................................................. 28To replace the battery pack ................................................................................... 29Loading the large-capacity battery pack into the Handheld Terminal .................. 31Removing and Installing the Alkaline Battery Holder .................................. 32Removal Procedure ...................................................................................... 32Installation Procedure ................................................................................... 33Attaching the Wrist Strap ............................................................................... 34Configuring Handheld Terminal Settings ..................................................... 35Adjusting Display Contrast ........................................................................... 35Turning Backlight On and Off ....................................................................... 35Using the Laser Scanner ................................................................................ 36Warning Label .............................................................................................. 37Bar Code Scanning Position ......................................................................... 37Using the C-MOS Imager ................................................................................ 38Warning Label .............................................................................................. 39Adjusting Laser Emission Width ................................................................... 40Emission Width Adjustment Bar code .................................................................. 41Performing Communication ........................................................................... 42IR Communication ........................................................................................ 42BluetoothTM Communication ......................................................................... 43DT-X5_E_P16_17.p65 2004.10.1, 9:47 AM16
E-17Resetting the Handheld Terminal ................................................................... 44Reset and Full Reset (Memory Initialization) ................................................ 44Reset ..................................................................................................................... 44Performing a Full Reset (Initialization) ................................................................ 44To perform a reset ........................................................................................ 44If reset does not find a memory problem .............................................................. 44If reset finds a memory problem........................................................................... 45To perform a full reset ................................................................................... 45DT-X5 Specifications ....................................................................................... 46Using the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO) ............................................................ 49General Guide .............................................................................................. 49Connecting the AC Adaptor and Connecting to Computer ........................... 51Removing the Fall Protector ......................................................................... 53Configuring DIP Switch Settings (HA-A61IO) ............................................... 54Using Wall Mount Unit .................................................................................. 55To remove the Bridge Satellite Cradle/Bridge Basic Cradle from the wall .......... 56Connecting Multiple Bridge Satellite Cradles (HA-A61IO) ............................ 57Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO) Specifications ....58Using the Cradle-type Battery Charger ......................................................... 59General Guide .............................................................................................. 59Connecting the AC Adaptor for Cradle-type Battery Charger ....................... 61Using Wall Mount Unit .................................................................................. 62Removing the Fall Protector ......................................................................... 62Cradle-type Battery Charger (HA-A30CHG) Specifications ......................... 62Using the Dual Battery Charger ..................................................................... 63General Guide .............................................................................................. 63Charging a Battery Pack ....................................................................................... 65Charge Indicator Lamp ......................................................................................... 65Connecting Multiple Dual Battery Chargers ................................................. 66Dual Battery Charger (DT-5022CHG) Specifications .................................... 67Using Rechargeable Battery Pack ................................................................. 68Battery Pack Specifications .......................................................................... 68Large-capacity Battery Pack Specifications .................................................. 68DT-X5_E_P16_17.p65 2004.10.1, 9:47 AM17
E-18Install the mainbatteryBefore Getting StartedBe sure to perform the following steps before using the Handheld Terminal for the firsttime.Handheld TerminalWrist StrapUser's Guide (this manual)Large-capacity battery pack CoverWhen unpacking, make sure that all items are included.Open the box and make sure that all the items shown here are included.Check the contentsof the boxTurn onthe power• Using the AA sizealkaline batteries• Using the battery pack(charging required)AA size Alkaline Batteries(DT-X5M10E/DT-X5M30E/DT-X5M30U only)Handheld TerminalESeriesUser’s GuideBe sure to read “Safety Precautions” inside this guide before trying to use your Handheld Terminal. After reading this guide, keep it in a safe place for future reference.DT-X5PN410388-002DT-X5_E_P18_24.p65 2004.10.1, 9:48 AM18
E-19Install the main batteryWhen Using the AA size Alkaline Batteries (DT-X5M10E/DT-X5M30E/DT-X5M30U only)1. Install the AA size alkaline batteries.1Slide the two main battery cover lockswitches on both sides of the HandheldTerminal to the “FREE” position, andremove the main battery cover.2Install the AA size alkaline batteries.Make sure the batteries are alignedproperly.21112213Return the main battery cover to itsoriginal position as shown in theillustration, and return the two mainbattery pack cover lock switches to the“LOCK” position.1233DT-X5_E_P18_24.p65 2004.10.1, 9:48 AM19
E-20When Using the Battery PackCharging is required when using the battery pack (HA-A20BAT or DT-5025LBAT) soldseparately.Use the Dual Battery Charger when charging the battery pack before installing in theHandheld Terminal, or use the Cradle-type Battery Charger or Cradle to charge afterinstalling in the Handheld Terminal.1. Remove the alkaline battery holder if it is installed.Refer to page 32 for information on removing the alkaline battery holder.2. Use the Dual Battery Charger when charging the battery pack in advance.Refer to page 65 for information on the charging procedure.3. Load the battery pack into the Handheld Terminal.1Slide the two main battery cover lockswitches on both sides of the HandheldTerminal to the “FREE” position, andthen remove the main battery cover.2Load a battery pack (HA-A20BAT) or alarge-capacity battery pack (DT-5025LBAT).•Take care that the battery pack isoriented correctly when you load it.•Install the battery pack so that thebattery pack removal tape is on topof the battery pack.12211Before Getting StartedDT-X5_E_P18_24.p65 2004.10.1, 9:48 AM20
E-213Return the main battery cover to itsoriginal position as shown in theillustration, and return the two mainbattery pack cover lock switches to the“LOCK” position.When loading a large-capacity batterypack, attach the large-capacity batterypack cover.•Make sure the battery pack removaltape is bent to the inside so as not tobe pinched by the cover.4. Use the Cradle-type Battery Charger or Cradle when charging the battery charger afterinstalling in the Handheld Terminal. Refer to pages 50 and 60 for information on thecharging procedure.Turning On the Power1. Turn on the Handheld Terminal byholding down the power key for aboutone second after waiting about 5 secondsafter installing the main battery.Start up the application you want to run.2331DT-X5_E_P18_24.p65 2004.10.1, 9:48 AM21
E-22Handheld Terminal System ConfigurationOptionsDT-X5 SeriesHA-A60IOHA-A61IOBridge Satellite Cradle (HA-A61IO)Bridge Basic Cradle (HA-A60IO)Cradle-type Battery ChargerHA-A30CHGLaser Scanner modelsThe laser scanner modelsare not available in theUSA and Canada.•DT-X5M10E•DT-X5M10RC-MOS Imager models•DT-X5M30E•DT-X5M30R•DT-X5M30U•DT-X5M30UR AD-S42120ARequired AC Adaptor for Bridge Satellite Cradle/Bridge Basic Cradle/Cradle-type Battery CharagerDT-X5_E_P18_24.p65 2004.10.1, 9:48 AM22
E-23HA-A20BAT(Battery Pack)DT-5025LBAT(Large-capacity Battery Pack)Battery PackDT-891WH RequiredScrewsWall Mount UnitDual Battery ChargerDT-5022CHGRequired AC Adaptor(MPC-577ADP)DT-X5_E_P18_24.p65 2004.10.1, 9:48 AM23
E-24CablesDT-887AXADT-888RSCDT-380USBBridge Satellite Cradle Cable/RS-232C Dsub-9Pin (Female)RS-422 Modular CableUSB CableHandheld Terminal System ConfigurationDT-X5_E_P18_24.p65 2004.10.1, 9:48 AM24
E-251 Indicator 12 Indicator 23 LCD Panel4 Power Key5 L Key6 R Key7 Cursor Key8 Multi Key9 Numeric Keys10 Execute KeyThis indicator is green when charging is completed, and redduring charging.This indicator is green when the bar code has been read successfully,and red when a reading error has occurred.Displays text, operating instructions and so forth.Switches the power on and off (press for about 1 second).This is pressed to move the cursor to the left.This is pressed to move the cursor to the right.This functions in mainly the same manner as the cursor keys on aPC. It is used when selecting items or scrolling the screen up anddown and so on.This can be set to perform arbitrary functions.These are pressed to input numbers and letters.This is pressed after entering a value or when advancing to thenext step.General GuideLeft Front Right Back12163548107212217181415691112131619202423Bottom *The illustration shows the Laser Scanner model.DT-X5_E_P25_26.p65 2004.10.1, 9:48 AM25
E-2611 Function Keys12 IR Port13 Power Contacts14 CLR Key15 Fn Key16 Main Battery CoverLock Switches17 R Trigger Key18 L Trigger Key19 Wrist Strap Hook20 Reset Switch21 Main Battery Cover22Bar code Reader Port23 Buzzer24 MaintenanceConnector CoverThese can be assigned arbitrary functions other than functions for readingbar codes. They are initially assigned the following default settings.F1: Deletes one character to the left.F2: Inputs a hyphen (-).F3: Inputs a period (.).F4: Switches character input (between numbers and alphabets(upper case)).F5: Inputs a space.F6: Functions similar to the Tab key on a PC. Used to moveitems for input or selection.F7: Functions similar to the Tab key on a PC. Used to moveitems for input or selection (but moves the opposite to F6).F8: Not set.This port is used for IR communication with another HandheldTerminal or with the Bridge Satellite Cradle/Bridge Basic Cradle.These are used to supply power from the Bridge Satellite Cradle/Bridge Basic Cradle and Cradle-type Battery Charger.This is pressed to clear the contents of all key inputs.This is used to make various settings or start up preliminaryregistered applications by sequentially pressing in combination witha function key (F1 to F8) or numeric key (0 to 9).The following examples show the combinations with the numerickeys.Fn + 1: Switches backlight on and off.Fn + 2: Darkens contrast.Fn + 3: Lightens contrast.Slide these switches when opening and closing the main batterycover.This key is used to read bar codes. It is also pressed whenperforming a full reset.This key is used to read bar codes. It is also pressed whencanceling a full reset.This is used when attaching the wrist strap.This is pressed to reset the Handheld Terminal.Covers the compartment that holds the battery pack or AA sizealkaline batteries.Laser light is emitted from this.Reads bar codes (Laser Scanner models)Reads bar codes and stacked 2D codes (C-MOS Imager models)Produces a buzzer tone.This is used when performing maintenance and repairs. Thiscover should normally not be opened.General GuideDT-X5_E_P25_26.p65 2004.10.1, 9:48 AM26
E-27Replacing the BatteryYour Handheld Terminal uses two types of battery: main battery and a memory backupbattery.AA size alkaline batteries (DT-X5M10E/DT-X5M30E/DT-X5M30U) or the battery packis used for the main battery. There are two types of battery packs that can be used,consisting of the battery pack (HA-A20BAT) and the large-capacity battery pack (DT-5025LBAT).The backup battery is installed inside of the Handheld Terminal.This guide uses the following terms to refer to the batteries.Main battery: Alkaline batteries or battery pack for operation.Backup battery: Memory backup battery contained within the Handheld Terminal.Battery pack: Generic name for the battery pack (HA-A20BAT) and large-capacitybattery pack (DT-5025LBAT) used for the main battery.If the main battery becomes worn down, either replace with new AA size alkalinebatteries, promptly charge the battery pack or replace with a charged battery pack.You can use the Dual Battery Charger, the Cradle-type Battery Charger, or the BridgeSatellite Cradle/Bridge Basic Cradle to charge a battery pack. See the sections of thisguide that cover the Dual Battery Charger, the Cradle-type Battery Charger, and theBridge Satellite Cradle/Bridge Basic Cradle for information about how to use them forcharging.Replacing the Battery PackImportant!Always keep backup copies of all important data!•The main battery powers normal operation and also provides power required tomaintain memory contents, while the backup battery provides backup power tomaintain memory contents. Because of this, you should not remove the mainbattery while the backup battery is dead. Removing the battery pack while thebackup battery is dead causes data in the memory to be corrupted or lost. Notethat once data is lost it cannot be recovered. Always keep separate backup copiesof all important data.•The charge of a battery pack when you purchase it may be depleted due to testingat the factory or natural discharge during shipment and storage. Be sure tocharge the battery pack before you use it.•The life of a battery pack is limited, and charging a battery pack causes it togradually lose its ability to maintain the charge. If your battery pack seems to requirecharging very frequently, it probably means it is time to purchase a new one.•The backup battery achieves a full charge in about four days when the batterypack is loaded.•A fully charged backup battery can maintain memory (RAM) contents for aboutthree days, even when the main battery is removed.•When using batteries for the main battery, always make sure to use AA sizealkaline batteries.DT-X5_E_P27_35.p65 2004.10.1, 9:48 AM27
E-28Replacing the BatteryReplacing the AA size Alkaline Batteries (DT-X5M10E/DT-X5M30E/DT-X5M30U only)1. Make sure the Handheld Terminal is turned off.If the power is on, press the power key to turn it off.2. Turn over the Handheld Terminal.3. Slide the two main battery cover lockswitches on both sides of the HandheldTerminal to the “FREE” position, andremove the main battery cover.21112214. Remove the AA size alkaline batteries asshown in the illustration.5. Install the new AA size alkaline batterieswhile making sure the batteries arealigned properly.DT-X5_E_P27_35.p65 2004.10.1, 9:48 AM28
E-29To replace the battery pack1. Make sure that the Handheld Terminal is turned off.If the power is on, press the power key to turn it off.2. Turn over the Handheld Terminal.3. Slide the two main battery cover lockswitches on both sides of the HandheldTerminal to the “FREE” position, andremove the main battery cover.16. Return the main battery cover to itsoriginal position as shown in theillustration, and return the two mainbattery cover lock switches to the“LOCK” position.233211DT-X5_E_P27_35.p65 2004.10.1, 9:48 AM29
E-30Replacing the Battery4. Remove the battery pack by pulling up onthe battery pack removal tape.5. Install a charged battery pack in theHandheld Terminal.•Take care to ensure it is orientedcorrectly.•Install the battery pack so that thebattery pack removal tape is on top ofthe battery pack.16. Return the main battery cover to itsoriginal position as shown in theillustration, and return the two mainbattery pack cover lock switches to the“LOCK” position.•Make sure the battery pack removaltape is bent to the inside so as not to bepinched by the main battery cover.23312DT-X5_E_P27_35.p65 2004.10.1, 9:48 AM30
E-31Loading the large-capacity battery pack into the Handheld TerminalAfter loading the large-capacity batterypack, you need to use the special large-capacity battery pack cover in place of thestandard battery cover.Attachment and removal of the large-capacity battery pack cover are the same asthose for the main battery cover. 3213DT-X5_E_P27_35.p65 2004.10.1, 9:48 AM31
E-32Removing and Installing the Alkaline BatteryHolder (DT-X5M10E/DT-X5M30E/DT-X5M30U only)Removal ProcedureWhen using a battery pack, first remove the alkaline battery holder according to thefollowing procedure.1. Make sure the Handheld Terminal is turned off. If the power is on, press the powerkey to turn it off.2. Turn over the Handheld Terminal.3. Slide the two main battery cover lockswitches on both sides of the HandheldTerminal to the “FREE” position, andremove the main battery cover.If the AA size alkaline batteries areinstalled, remove the batteries by referringto step 4 on page 28 describing “Replacingthe AA size Alkaline Batteries”.4. Remove the alkaline battery holder byholding the portion indicated by the circle(™) in the illustration while pushing thetab on the outer frame of the alkalinebattery holder to the inside.21112DT-X5_E_P27_35.p65 2004.10.1, 9:48 AM32
E-3312211Installation ProcedureWhen using AA size alkaline batteries, install the alkaline battery holder according to thefollowing procedure.1. Make sure the Handheld Terminal is turned off. If the power is on, press the powerkey to turn it off.2. Turn over the Handheld Terminal.3. Slide the two main battery cover lockswitches on both sides of the HandheldTerminal to the “FREE” position, andremove the main battery cover.If the battery pack is installed, remove thebattery pack by referring to step 4describing “To replace the battery pack”on page 30.4. Install the alkaline battery holder asshown in the illustration.Fold the battery pack removal tape so thatit is beneath the alkaline battery holder.DT-X5_E_P27_35.p65 2004.10.1, 9:48 AM33
E-34Attaching the Wrist StrapBe sure to attach the wrist strap and use it to protect against dropping the HandheldTerminal when carrying it around.Attach the wrist strap by following the procedure described below.1. Pass the thin cord of the wrist strapthrough the wrist strap hole on the back ofthe Handheld Terminal.2. Pass the other end of the strap (the partwhere you insert your wrist) through theloop formed by the thin cord.Important!Do not swing the Handheld Terminal around holding the wrist strap.DT-X5_E_P27_35.p65 2004.10.1, 9:48 AM34
E-35Configuring Handheld Terminal SettingsAdjusting Display ContrastPerform the following steps to adjust display contrast to make display more vivid andeasier to see.•Press the “Fn” key and then press the “2” key or “3” key after confirming that“F” is displayed in the lower right corner of the screen. Pressing the “2” keyadjusts for more contrast, while pressing the “3” key adjusts for less contrast.* In order to continue to make adjustments, press the “2” key or “3” key after again firstpressing the “Fn” key.* This can also be set by pressing the “2” key (Settings) on the system menu, and thenpressing the “2” key (Contrast and Brightness).Turning Backlight On and OffWhen operating the Handheld Terminal in a dark location, you can turn on the backlightto facilitate viewing of the screen.•You can switch the backlight on and off by pressing “1” after pressing the Fn key.DT-X5_E_P27_35.p65 2004.10.1, 9:48 AM35
E-36Using the Laser Scanner(DT-X5M10E/DT-X5M10R only)1. After turning on the power, position thelaser scanner close to a bar code and thenpress the Trigger key (R or L).2. The laser emits light and scans the barcode. If scanning is completed normally,Indicator 2 displays a green light and abuzzer sounds. Indicator 2 displays a redlight when an error has occurred duringreading.Important!•If you are unable to scan a bar code, try changing the angle at which the scanneris held or distance from the scanner to the bar code, and then try scanning again.•This Handheld Terminal is capable of scanning bar codes at a distance of 0~400 mm. Furthermore, the distance at which scanning is possible may varyaccording to the symbology.•The laser scanner models are not available in the USA and Canada.DT-X5_E_P36_48.p65 2004.10.1, 9:49 AM36
E-37Warning Label•This label is a warning label for Class 2 laser products thatcomply with IEC60825-1+A2:2001CAUTION•Use of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure.•The laser light emitted by this laser scanner has a maximum output of less than 1mW and a wavelength of 650 nm. Warning! Never look directly into the laser light.•This product scans using laser light. Never look directly into the laser light orshine the laser light into the eyes.Bar Code Scanning PositionPosition the Handheld Terminal close to the bar code when scanning small bar codes.Position the Handheld Terminal at a distance from the bar code so that the bars enter thelight when scanning large bar codes.Margin MarginGood Good GoodBad Bad Bad BadLaser light is emitted from this port.DT-X5_E_P36_48.p65 2004.10.1, 9:49 AM37
E-38Using the C-MOS Imager(DT-X5M30E/DT-X5M30R/DT-X5M30U/DT-X5M30UR only)1. Turn on the Handheld Terminal, position its C-MOS Imager reader port near the barcode or stacked 2D code, and then press the Trigger Key (R or L).2. The Handheld Terminal reads the code by emitting laser and red light.Indicator 2 (read operation indicator lamp) lights in green when the reading is successful.Bar code and stacked 2D code Reading GuideWhen you press the Trigger key (R or L), LEDs in the Handheld Terminal emit laserand red lights. Align the laser frame with the center of the bar code or stacked 2Dcode you are trying to read. Take particular care aligning the light when there areother bar codes nearby.When reading a large code, adjust the position of the Handheld Terminal so that theentire code is enclosed within the laser frame.Important!•If you have problem not properly reading a code, change the angle and/or thedistance between the label and the Handheld Terminal and try reading the codeagain.•A bar code can be read from a distance of 40mm to 410mm (19/16" to 161/8"), and astacked 2D code can be read from a distance of 50mm to 250mm (11515151515⁄⁄⁄⁄⁄1616161616" to 91313131313⁄⁄⁄⁄⁄1616161616").The actual reading distance depends on the symbology and the resolution.•For smaller codes, move the Handheld Terminal closer to the code.•To read a large code, move the Handheld Terminal further away from the code.•Note that a special reader application is required to read bar codes and stacked 2Dcodes.•The DT-X5M30E/M30R/M30U/M30UR supports reading of stacked 2D codes.•Fingerprints, dust, dirt, or other foreign matter on the C-MOS Imager readerport can cause abnormal reading. Should the code reader port become dirty,wipe it clean with a soft and dry cloth.DT-X5_E_P36_48.p65 2004.10.1, 9:49 AM38
E-39Warning Label•This label is a warning label for Class 2 laser products that comply withIEC60825-1+A2:2001CAUTION•Use of controls or adjustments or performance of procedures other than thosespecified herein may result in hazardous radiation exposure.•The laser light emitted by this laser scanner has a maximum output of less than 1mW and a wavelength of 650 nm. Warning! Never look directly into the laser light.•This product scans using laser light. Never look directly into the laser light orshine the laser light into the eyes.Laser light is emitted from this port.DT-X5M30UDT-X5M30URDT-X5M30EDT-X5M30RDT-X5_E_P36_48.p65 2004.10.1, 9:49 AM39
E-40Adjusting Laser Emission Width(DT-X5M10/DT-X5M10R only)This Handheld Terminal is able to adjust the emission width of laser light. Adjust theHandheld Terminal by following the procedure described below when the emissionwidth of the laser light has become off the proper emission width.1. Press the reset switch on the back of the HandheldTerminal to initiate the Top menu.2. Press the keys in the order of the “2” key (Setting), “1”key (Scanner setting) and then “4” key (OBRcalibration) to initiate the emission width adjustmentfunction.3. Press the trigger key to emit laser light, and shine thelight on the emission width adjustment bar code.•Align the laser light with the narrow bars on bothsides.DT-X5_E_P36_48.p65 2004.10.1, 9:49 AM40
E-41Emission Width Adjustment Bar codeImportant!•An error message is displayed when emission width has not been adjustedproperly. Repeat the adjustment procedure when this message is displayed.4. After checking that the laser light is at the properposition, depress the trigger key for about 1 second.•This completes adjustment of the emission width.DT-X5_E_P36_48.p65 2004.10.1, 9:49 AM41
E-42Performing CommunicationIR CommunicationIR communication can be used to transfer data between two Handheld Terminals.When performing IR communication, orient the IR ports of both Handheld Terminals sothey are pointing directly at each other.The ports can be in direct contact with each other, or they can be separated by up to 30 cm(117⁄8").Important!•A high-sensitivity communication element is used during IR communication.•In order to ensure successful communication, avoid using cellular phones or otherdevices that emit radio wave in the area where you are performing IRcommunication.•If you need to use such a device, move away from the communicating HandheldTerminals. In case of a cellular phone, keep it at least 30cm (1177777⁄⁄⁄⁄⁄88888") away.DT-X5_E_P36_48.p65 2004.10.1, 9:49 AM42
E-43BluetoothTM CommunicationBluetoothTM protocol can also be used to transfer data between two Handheld Terminals.With BluetoothTM, the two Handheld Terminals should be located within about fivemeters (1911⁄16") from each other, as long as there is nothing blocking the path betweenthem.Important!Observe the following precautions to help ensure that the communication issuccessful.•Make sure the BluetoothTM devices are located within five meters (191111111111⁄⁄⁄⁄⁄1616161616") of eachother. The particular surroundings (obstacles) may require a shorter distancebetween the two devices.•Make sure there is at least two meters (6' 7") between this device and otherdevices (electrical appliances, audio-visual equipment, OA equipment, and digitalcordless telephones, facsimile machines, etc.). (Take special care with microwaveovens. Allow at least three meters (9' 1033333⁄⁄⁄⁄⁄88888") between communicating devices and amicrowave oven.) When approaching such a device when its power is turned on,proper communication may prove impossible while this may also causeinterference with TV and radio reception (images produced by certain UHF andbroadcast satellite channels may become blurry).•Normal communication may not be possible in an area near a broadcasttransmitter or wireless transmitter. If this happens, move to a different location.Normal communication may not be possible in areas exposed to strong radiowaves.•Wireless LAN InterferenceBecause BluetoothTM and Wireless LAN use the same frequency band (2.4GHz),radio interference can occur if there is a Wireless LAN device nearby. This canresult in lower communication speeds, or even make it impossible to establish aconnection. If this happens, try the following countermeasures.•Move at least 10 meters (32'103⁄4") away from the Wireless LAN device.•If you cannot keep the distance at least 10 meters (32'103⁄4") or more between theHandheld Terminal and a Wireless LAN device, turn off the power of either theHandheld terminal or the Wireless LAN device.•Set the Wireless LAN mode of the Handheld Terminal to off (DT-X5M10R/DT-X5M10UR/DT-X5M30R/DT-X5M30UR).DT-X5_E_P36_48.p65 2004.10.1, 9:49 AM43
E-44Resetting the Handheld TerminalReset and Full Reset (Memory Initialization)ResetResetting the Handheld Terminal is the same as restarting a computer. Performing a resetcauses all unsaved inputs and edits to be lost, but data that is already stored in thememory as well as all settings should be unaffected.Use reset to restore normal operation whenever the Handheld Terminal operatesabnormally due to misoperation or some other reason.Performing a Full Reset (Initialization)Performing a full reset initializes memory. This means that all data stored in the memory(RAM) is deleted and all the settings are returned to their initial factory defaults.Perform a full reset whenever any one of the following conditions exists.•When you want to delete all memory contents and return the settings to their initialfactory defaults.•When you are no longer able to use the Handheld Terminal because you forgot yourpassword.•When the Handheld Terminal does not operate normally due to a memory problem.•When the message “A problem with memory contents has been found” is displayed.To perform a resetPress the reset switch on the back of theHandheld Terminal with a pen or similarobject. This starts reset processing.If reset does not find a memory problemThe Handheld Terminal restarts, and normal operation is restored.DT-X5_E_P36_48.p65 2004.10.1, 9:49 AM44
E-45If reset finds a memory problemA message like the one shown below appears on the display when the reset operationdiscovers a memory problem.When this message appears, press the R trigger key to continue with the reset operation.Note, however, that reset may not be successful depending on the condition of thememory. In this case, perform the full reset operation described on the next page.To perform a full resetImportant!Performing a full reset deletes all data currently stored in the memory (RAM). Ifpossible, backup data of the Handheld Terminal to a computer, Flash Memory, amemory card, or some other medium before performing a full reset.1. The following message is displayed when the reset switch is pressed for about onesecond with a pen or similar object while pressing the power key.R trigger keyL trigger key•To cancel the full reset operation, press the L trigger key instead of the R trigger key.2. Press the R trigger key. This causes the message shown below to appear.R trigger keyL trigger key•To cancel the full reset operation, press the L trigger key instead of the R trigger key.3. Press the R trigger key again.•Full reset is performed, all data in the memory (RAM) are erased and the start-upscreen is displayed.R trigger keyL trigger keyDT-X5_E_P36_48.p65 2004.10.1, 9:49 AM45
E-46DT-X5 Specifications1. Handheld TerminalModel: DT-X5M10E, DT-X5M10R, DT-X5M30E, DT-X5M30R,DT-X5M30U, DT-X5M30URCPU: 32-bit RISC typeMemory: 16MB RAM (user area: Approximately 7.5MB)64MB Flash ROM (user area: Approximately 30MB)OS: Microsoft® Windows® CE.NET operating system, EnglishVersionDisplay: 128 × 160 dot, monochrome FSTN LCD2. Laser Scanner (DT-X5M10E/DT-X5M10R)Reading symbologies: EAN8/JAN8, EAN13/JAN13, UPCA, UPCE, Code39, Codabar(NW7), Interleaved2of5 (ITF), Code93, Code128, MSI(Plessey), IATA, RSS-14, RSS Limited, RSS Expanded,Industrial2of5 (IDF)Reading distance: Within approximately 0~400 mm (0 to 153/4")3. C-MOS Imager (DT-X5M30E/DT-X5M30R/DT-X5M30U/DT-X5M30UR)Reading 1D Code symbologies:EAN8/JAN8, EAN13/JAN13, UPCA, UPCE, Code39, Codabar(NW7), Interleaved2of5 (ITF), Code93, Code128, MSI(Plessey), IATA, Code11, RSS-14, RSS Limited, RSS Expanded,ISBTReading distance: Within approximately 40 mm~410 mm (19/16" to 161/8")Reading stacked 2D Code symbologies:Code49, PDF417, MicroPDF, Codablock F, EAN8/13Composite, RSS Composite, UCC/EAN128 Composite, TLC39,RSS-14 (Stacked type), RSS Expanded (Stacked type)Reading distance: Within approximately 50 mm to 250 mm (115/16" to 913/16")4. Infrared CommunicationProtocol: Compatible with IrDA Ver. 1.1 (max. 300 mm)Synchronization: Asynchronous, frame synchronizationTransfer rate: 4 Mbps (max.)5. BluetoothTMProtocol: BluetoothTM Specification Ver. 1.1Range: Approximately 5 m (varies according to radio wave conditionsand local surroundings)Output: Max. 3 dBm (PowerClass 2)6. Wireless LAN (DT-X5M10R/DT-X5M30R/DT-X5M30UR)Protocol: Complies with IEEE802.11bRadio frequency: 2.400-2.4835 GHzData rate: Max. 11 MbpsRange: 50 m indoors, 150 m outdoors (varies according to localsurroundings)Channels: 11 (US, Canada), 13 (ETSI)Other functions: Roaming among multiple Access-PointsDT-X5_E_P36_48.p65 04.10.8, 10:12 AM46
E-477. PowerMain power supply: Two AA size alkaline batteriesHA-A20BAT battery packDT-5025LBAT large-capacity battery packBackup power supply: Rechargeable lithium battery (built-in)Power consumption: DC 1.1A/3~5V (DT-X5M10E)DC 1.3A/3~5V (DT-X5M30E/DT-X5M30U)DC 1.4A/3.7~5V (DT-X5M10R)DC 1.6A/3.7~5V (DT-X5M30R/DT-X5M30UR)Battery life: Main batteryDT-X5M10EApprox. 140 hours (AA size alkaline batteries × 2pcs)*Approx. 70 hours (HA-A20BAT)*Approx. 140 hours (DT-5025LBAT)*DT-X5M10R Approx. 70 hours (HA-A20BAT)*Approx. 140 hours (DT-5025LBAT)*Approx. 12 hours (HA-A20BAT)**Approx. 24 hours (DT-5025LBAT)**DT-X5M30E/Approx. 30 hours (AA size alkaline batteries × 2pcs)*DT-X5M30U Approx. 30 hours (HA-A20BAT)*Approx. 60 hours (DT-5025LBAT)*DT-X5M30R/ Approx. 30 hours (HA-A20BAT)*DT-X5M30UR Approx. 60 hours (DT-5025LBAT)*Approx. 12 hours (HA-A20BAT)**Approx. 24 hours (DT-5025LBAT)*** In the case of scanning two bar codes per 10 seconds atnormal temperature** In the case of standby (6.5): Scanning (1.5): Wirelesscommunication(2)Memory backupData protection (RAM): 3 days (when there is no powerfrom main battery)Clock: 4 weeks (when there is no power from main battery)8. Operating EnvironmentTemperature: –20 to 50°CHumidity: 10% to 80% RH (no condensation)9. Dimensions and WeightDimensions:DT-X5M10E/ Approx. 54 (70)* W × 179D × 21.4 (41.1)* H mmDT-X5M10RDT-X5M30E/ Approx. 54 (70)* W × 179D × 21.4 (42.8)* H mmDT-X5M30U/DT-X5M30R/DT-X5M30UR/DT-X5_E_P36_48.p65 2004.10.1, 9:49 AM47
E-48WeightDT-X5M10E/ Approx. 245 g (when HA-A20BAT battery pack is installed)DT-X5M30E/DT-X5M30UDT-X5M10R/ Approx. 250 g (when HA-A20BAT battery pack is installed)DT-X5M30R/DT-X5M30UR10.Drop durability: 1.8 m11.Dust and water resistance: Complies with IP54* When all connectors and covers are closed12.OtherClock function: Year, month, date, hour, minute, full-auto calendar, alarmVibrator function: Available by setting softwareDT-X5 SpecificationsDT-X5_E_P36_48.p65 2004.10.1, 9:49 AM48
E-491 2 3 451511121413109867BottomFrontRightBackTopFall protect coverAccessoryUsing the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO)The optionally available Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle(HA-A60IO) make it possible to transfer system data and file data between theHandheld Terminal and a computer over an RS-232C connection or USB connection(USB connection only for HA-A60IO). You can also use the Bridge Satellite Cradle/Bridge Basic Cradle to charge the battery pack installed on the Handheld Terminal.An optionally available wall mount unit (DT-891WH) lets you mount the Bridge SatelliteCradle on a wall.General GuideDT-X5_E_P49_58.p65 2004.10.1, 9:49 AM49
E-50Using the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO)1 USB Port2 RS-232C Port(HA-A61IO only)3 RS-422C Port(HA-A61IO only)4 AC Adaptor Jack5 Wall Mount UnitFastening Plate6 Terminal DetectSwitch7 IR Port8 Power Contacts9 Power IndicatorLamp10 CommunicationIndicator Lamp(HA-A61IO only)11 System StatusIndicator Lamp12 Power Switch13 Desktop Unit14 DIP Switches(HA-A61IO only)15 Fall ProtectorThis port accepts connection of a USB cable for connection to acomputer for transfer of system data and file data. Use of the USBport requires installation of a special driver on the PC.This port accepts connection of an RS-232C cable for connectionto a computer for transfer of system data and file data. Use of theRS-232C port requires installation of a special driver on the PC.This port is used when connecting to another Bridge SatelliteCradle.Connect the AC adaptor sold separately to supply power.The holes in this plate accept screws that secure the wall mountunit in place.This switch detects when the Handheld Terminal is not seatedcorrectly on the Bridge Satellite Cradle.This port transfers data with the Handheld Terminal IR port non-contact data communication.Power is supplied to the Handheld Terminal via these contacts.This lamp indicates the Power Status and the mounting status ofthe Handheld Terminal.Off: Power offGreen: Power on, Handheld Terminal mounted correctlyRed: Power on, Handheld Terminal not mountedThis lamp shows when the Handheld Terminal is performing datacommunication.Off: No data communication being performedGreen flashing: Data communication in progressRed: Problem with a connection between two Bridge SatelliteCradlesThis lamp indicates whether the system is operating normally.Regardless of whether or not a Handheld Terminal is mountedthis lamp indicates the system status and whether or not acommunication operation with the system can be performed.Off: System is not operating.Green: System is operating.Turns the power on and off.This is the base when using the Bridge Satellite Cradle/BridgeBasic Cradle in a desktop configuration. Remove the desktop unitin the case of a wall-mount configuration.Use these switches to configure the Bridge Satellite Cradle asrequired.This is a removable attachment that prevents the HandheldTerminal from tipping over and falling.DT-X5_E_P49_58.p65 2004.10.1, 9:49 AM50
E-51Connecting the AC Adaptor and Connecting to ComputerUse the AC adaptor sold separately from the Bridge Satellite Cradle/Bridge Basic Cradlefor the power supply of the Bridge Satellite Cradle/Bridge Basic Cradle. Always makesure that the power is being supplied to the Bridge Satellite Cradle by the AC adaptorbefore performing any type of data communication operation with the HandheldTerminal. The Handheld Terminal draws the power via the Bridge Satellite Cradle/Bridge Basic Cradle during data communication.1. After making sure that the Bridge SatelliteCradle/Bridge Basic Cradle power switchis turned off, plug the AC adaptor into theAC adaptor jack on the back.2. Next, plug the AC adaptor into a poweroutlet.3. After making sure that the Bridge SatelliteCradle/Bridge Basic Cradle and yourcomputer are both turned off, remove thecap from the Bridge Satellite Cradle/Bridge Basic Cradle connection ports, andthen perform one of the following steps toconnect to your computer.Be sure to keep the Bridge Satellite Cradle/Bridge Basic Cradle connection portscovered whenever you are not using them.RS-232C Connection•Connect an RS-232C cable (DT-887AXA) to the RS-232C port (HA-A61IO only) of the Bridge SatelliteCradle. Connect the other end to yourcomputer’s RS-232C port.USB Connection•Connect a USB cable (DT-380USB) tothe USB port of the Bridge SatelliteCradle/Bridge Basic Cradle. Connectthe other end to your computer’s USBport.4. Turn on the power. This causes the BridgeSatellite Cradle/Bridge Basic Cradlepower indicator lamp to light in red.Power switch (OFF)When using the USB portPOWER DATA LINESystem Status Indicator LampPower Indicator LampCommunication Indicator Lamp(HA-A61IO only)Power switch (ON)Power contactsDT-X5_E_P49_58.p65 2004.10.1, 9:49 AM51
E-52Using the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO)5. Making sure that their two IR ports come into contact with each other, place theHandheld Terminal onto the Bridge Satellite Cradle. This causes the Bridge SatelliteCradle power indicator lamp to light in green.•If the system is operating normally and the communication is enabled, the systemstatus indicator lamp lights in green.•The communication indicator lamp flashes in green when the communication starts.When charging is initiated, Indicator 1 on the Handheld Terminal lights up in red. Whencharging has been completed, Indicator 1 on the Handheld Terminal changes color fromred to green.Important!•A high-sensitivity communication element is used during IR communication.In order to ensure successful communication, avoid using cellular phones or otherdevices that emit radio wave in the area where you are performing IRcommunication.If you need to use such a device, move away from the communicating HandheldTerminals. In case of a cellular phone, keep it at least 30cm (1177777⁄⁄⁄⁄⁄88888") away.•Take care to avoid allowing the Bridge Satellite Cradle/Bridge Basic Cradlepower contacts to become connected to each other, which creates a short.Shorting the power contacts can damage the Bridge Satellite Cradle/Bridge BasicCradle.DT-X5_E_P49_58.p65 2004.10.1, 9:49 AM52
E-53Removing the Fall ProtectorThe Bridge Satellite Cradle and Cradle-type Battery Charger Fall Protector can also beremoved. However, it is recommended not to remove the Fall Protector if there is therisk of the Handheld Terminal being mistakenly tipped over and falling after having beenplaced in the Bridge Satellite Cradle. The Fall Protector should always be left attachedwhen the Handheld Terminal is mounted on a wall.1. Remove the Fall Protector by applyingforce in the direction of the arrow whileholding at the location of™in theillustration with the Bridge SatelliteCradle lying horizontally.2. Affix the seal to the location where theFall Protector was attached.12When attaching, remove the seal andinsert the projections on the Fall Protectorinto the attachment groove, and then slidethe Fall Protector to the left to fasten inposition.DT-X5_E_P49_58.p65 2004.10.1, 9:49 AM53
E-54Using the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO)Configuring DIP Switch Settings (HA-A61IO)Dismounting the bottom cover of the Bridge Satellite Cradle exposes the DIP switches.You can change the ON/OFF settings of the DIP switches to set the configuration. Pleaseset after first switching OFF the power.12345678Not used (Always off)Not used (Always off)Host Computer InterfaceSettingRS-232CUSB6OFFONSettingIntermediate UnitDaisy Chain Disabled/Termination5OFFONSettingHost ComputerDaisy Chain3OFFON4OFFOFFDaisy ChainConnection TypeSetting115,200bps*Initial factory default setting1ON2OFFBridge Satellite Cradle Data Rate****Important!Note that other DIP settings are used for testing and inspection purposes. Becauseof this, you should never use any DIP settings other than those described above.DT-X5_E_P49_58.p65 2004.10.1, 9:49 AM54
E-55Using Wall Mount UnitThe following procedure explains how to use the optional wall mount unit (DT-891WH)to configure the Bridge Satellite Cradle/Bridge Basic Cradle for a wall-mountedconfiguration.Important!When mounting on a wall, always make sure to attach the Fall Protector.1. Remove the screws on the bottom of theBridge Satellite Cradle/Bridge BasicCradle, and remove the desktop unit.2.Affix the wall mount unit to the bottom ofthe Bridge Satellite Cradle/Bridge BasicCradle, and secure it in place with the wallmount unit screws.3. Drive one of the provided screws into thewall at the location where the upper holeof the wall mount unit to be when youmount the unit on the wall.Do not drive the screw into the wall all theway. Keep a space of about 2mm (1/8")between the head of the screw and thewall surface.ScrewsScrews2mm (1/8")DT-X5_E_P49_58.p65 2004.10.1, 9:49 AM55
E-56Using the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO)4. Hook the upper wall mount unit hole ontothe upper screw.5. Drive the other screw into the wall at thelocation where the lower hole is located.6. Drive the upper screw and lower screwinto the wall the rest of the way.To remove the Bridge Satellite Cradle/Bridge Basic Cradle from thewall1. Loosen the upper screw and lower screw.2. Raise the Bridge Satellite Cradle/Bridge Basic Cradle and remove it from the screws.Important!•While the Bridge Satellite Cradle/Bridge Basic Cradle is mounted on a wall, besure to check the wall screws periodically for looseness. Tighten them as required.•Note use of the RS-232C cable is not supported by the wall-mountedconfiguration. Connect using a USB cable or daisy chain cable.DT-X5_E_P49_58.p65 2004.10.1, 9:49 AM56
E-57Connecting Multiple Bridge Satellite Cradles (HA-A61IO)Use the modular cable for the connections.You can daisy chain multiple BridgeSatellite Cradles by connecting the C-OUTport of the first unit that is the nearest to thehost computer to the C-IN port of the nextunit that is sitting to the first unit with DT-888RSC cable (RS-422 Modular cable) asshown in the figure below.Important!You can use optional RS-422 Modular Cables (DT-888RSC) to link up to eightBridge Satellite Cradles.To host computerDaisy chain connection cables (DT-888RSC)RS-232C cable or USB cableDT-X5_E_P49_58.p65 2004.10.1, 9:49 AM57
E-58Using the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO)Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle(HA-A60IO) Specifications1. IR CommunicationInterface: IR interfaceProtocol: IrDA Ver. 1.1 StandardSynchronization: Asynchronous, frame synchronizationTransfer Rate: 9,600, 115,200, 4Mbps(4Mbps is possible during a USB connection with the hostcomputer only.)2. USBProtocol: USB Ver1.1 StandardTransfer Rate: 12Mbps (max.)3. RS-232C (HA-A61IO)Protocol: Full duplexSynchronization: AsynchronousTransfer Rate: 115,200bps4. RS-422 (HA-A61IO)Protocol: Full duplexSynchronization: AsynchronousTransfer Rate: 115,200bps5. ChargingCharging System: Fixed-voltage (with current limiter)Charge Time: Approximately 5.0 hours (standard battery pack)Approximately 10 hours (large-capacity battery pack)6. Power SupplyPower Requirement: AC adaptor (AD-S42120A)Power Consumption: DC12V approximately 1.0A (HA-A60IO)DC12V approximately 0.9A (HA-A61IO)Output to Handheld Terminal: DC5V 1.5A (max.)7. AC AdaptorModel: AD-S42120AInput: 100V to 240V AC 50/60HzOutput: 12V DC 3.5A8. Dimensions and WeightDimensions:Desktop: Approximately 110(W) × 125(D) × 128(H) mm(43⁄8"W × 415⁄16"D × 51⁄16"H)Wall Mount: Approximately 110(W) × 148(D) × 153(H) mm(43⁄8"W × 57⁄8"D × 6"H)Weight: Desktop: Approximately 520g (18.34oz) (HA-A60IO)Approximately 530g (18.7oz) (HA-A61IO)Wall Mount: Approximately 610g (21.52oz) (HA-A60IO)Approximately 620g (21.87oz) (HA-A61IO)9. Operating EnvironmentTemperature: 0°C to 40°C (32°F to 104°F)Humidity: 30% to 80% RH (non-condensation)DT-X5_E_P49_58.p65 2004.10.1, 9:49 AM58
E-59Using the Cradle-type Battery ChargerThe optionally available Cradle-type Battery Charger (HA-A30CHG) lets you charge theHandheld Terminal’s battery simply by placing the Handheld Terminal onto the charger.An optional wall mount unit (DT-891WH) lets you mount the Cradle-type BatteryCharger on a wall.General GuideBackTopFrontRight BottomFall protect coverAccessory12675438 9DT-X5_E_P59_70.p65 2004.10.1, 9:50 AM59
E-60Using the Cradle-type Battery Charger1 AC Adaptor Jack2 Wall Mount UnitFastening Plate3 Terminal DetectSwitch4 Power Contacts5 Power IndicatorLamp6 Power Switch7 Desktop Unit8 Fall Protector9 Car MountedBattery ChargerAttachment HolesConnect the AC adaptor (sold separately) here.The holes in this plate accept screws that secure the wall mountunit in place.This switch detects when the Handled Terminal is not seatedcorrectly on the Cradle.Power is supplied to the Handheld Terminal via these contacts.This lamp indicates the power status and the mounting status ofthe Handheld Terminal.Off: Power offRed: Power on, Handheld Terminal not mountedGreen: Power on, Handheld Terminal mounted correctlyTurns the power on and off.This is the base when using the Cradle in a desktop configuration.Remove the desktop unit in the case of a wall-mountconfiguration.This is a removable attachment that prevents the HandheldTerminal from tipping over and falling.This is used when attaching the separately sold Battery ChargerCar Mount Unit (HA-A34AT).DT-X5_E_P59_70.p65 2004.10.1, 9:50 AM60
E-61Connecting the AC Adaptor for Cradle-type Battery ChargerUse the special AC adaptor (sold separately) for the Cradle-type Battery Charger toconnect to a wall outlet.1. After making sure that the Cradle-typeBattery Charger power switch is turnedoff, plug the AC adaptor into the ACadaptor jack on the back of the charger.2. Next, plug the AC adaptor into a poweroutlet.3. Turn on the power. This causes theCradle-type Battery Charger powerindicator lamp to light in red.4. Making sure that their power contactscome into contact with each other, placethe Handheld Terminal onto the Cradle-type Battery Charger. This causes theCradle-type Battery Charger powerindicator lamp to light in green.When charging is initiated, Indicator 1 onthe Handheld Terminal lights up in red.When charging has been completed,Indicator 1 changes color from red togreen.Important !Take care to avoid allowing the Cradle-type Battery Charger power contacts tobecome connected to each other, which creates a short.Shorting the power contacts can damage the Cradle-type Battery Charger.Power switch (OFF)POWERPower contactsPower switch (ON)Power Indicator LampDT-X5_E_P59_70.p65 2004.10.1, 9:50 AM61
E-62Using Wall Mount UnitTo wall mount the Cradle-type Battery Charger, use the same procedure as that describedfor the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO) on page55.Removing the Fall ProtectorThe procedure is the same as that for the Bridge Satellite Cradle (HA-61IO)/BridgeBasic Cradle (HA-A60IO). Refer to page 53.Cradle-type Battery Charger (HA-A30CHG) Specifications1. ChargingCharging System: Fixed-voltage (with current limiter)Charge Time: Approximately 5 hours (HA-A20BAT battery pack)Approximately 10 hours (DT-5025LBAT large-capacity battery pack)2. Power SupplyPower Requirement: AC adaptor (AD-S42120A)Power Consumption: 12V DC, approximately 0.9AOutput to Handheld Terminal: 5V DC 1.5A (max.)3. AC AdaptorModel: AD-S42120AInput: 100V to 240V AC 50/60HzOutput: 12V DC 3.5A4. Dimensions and WeightDimensions: Desktop: Approximately 110(W) X 125(D) X 128(H) mm(43⁄8"W × 415⁄16"D × 51⁄16"H)Wall Mount: Approximately 110(W) × 148(D) × 153(H) mm(43⁄8"W × 57⁄8"D × 6"H)Weight: Desktop: Approximately 510g (16.6oz)Wall Mount: Approximately 600g (22.2oz)5. Operating EnvironmentTemperature: 0°C to 40°C (32°F to 104°F)Humidity: 30% to 80% RH (non-condensation)Using the Cradle-type Battery ChargerDT-X5_E_P59_70.p65 2004.10.1, 9:50 AM62
E-63Using the Dual Battery ChargerThe optionally available Dual Battery Charger (DT-5022CHG) allows for parallelcharging of two rechargeable battery packs.General GuideTop BottomFront11444432 33AccessoriesConnection Bracket2 screwsDT-X5_E_P59_70.p65 2004.10.1, 9:50 AM63
E-64Using the Dual Battery Charger1 Charge IndicatorLamp2 AC Adaptor Jack3 Dual BatteryCharger ConnectionPort4 Connection BracketAttachment HolesThis lamp indicates the charge status of the battery pack(s).Off: Not chargingRed: ChargingRed Flashing: Battery pack problemGreen: Charging completeConnect the AC adaptor here.Use this port to connect multiple Dual Battery Chargers to eachother.The connection bracket attaches here when you connect multipleDual Battery Chargers to each other.Important!Each Dual Battery Charger comes with one connection bracket.Since only one connection bracket is required when you connect two Dual BatteryChargers, you will always have one left over.Simply keep the other connection bracket on hand as an extra, in case you everneed it.DT-X5_E_P59_70.p65 2004.10.1, 9:50 AM64
E-65Charging a Battery Pack1. Plug the optional AC adaptor into the ACadaptor jack of the Dual Battery Charger.2. Plug the other end of the AC adaptor intoa wall outlet.3. Taking care that the battery pack isoriented correctly, insert it into the DualBattery Charger.This causes the Charge Indicator Lamp tolight in red, indicating that charging hasstarted.Charge Indicator LampOff: Not chargingRed: ChargingRed Flashing: Battery pack problemGreen: Charging completeDT-X5_E_P59_70.p65 2004.10.1, 9:50 AM65
E-66Using the Dual Battery ChargerConnecting Multiple Dual Battery ChargersYou can connect up to three Dual Battery Chargers. Doing so makes it possible to supplypower to all the Dual Battery Chargers using the AC adaptor.1. As shown in the illustrations below, remove the connector covers of the Dual BatteryChargers you want to connect to each other.2. Connect the two Dual Battery Chargers asshown below.3. Turn over the connected Dual BatteryChargers and attach a connection bracket,securing it in place with screws.You can repeat the above steps to connectup to three Dual Battery Chargers.Connector coverDT-X5_E_P59_70.p65 2004.10.1, 9:50 AM66
E-67Dual Battery Charger (DT-5022CHG) Specifications1. ModelDT-5022CHG2. ChargingCharging System: Fixed-voltage (with current limiter)Charge Time: Approximately 2.5 hours for one HA-A20BAT battery packApproximately 5.0 hours for one DT-5025LBAT large-capacitybattery packCharging Two Battery PacksApproximately 5.0 hours for two battery packs (HA-A20BAT×2)Approximately 10 hours for two large-capacity battery packs(DT-5025LBAT×2)3. Power SupplyPower Requirement: AC adaptor MPC-577ADPConsumption Current: Approximately 650mA4. Operating EnvironmentTemperature: 0°C to 40°C (32°F to 104°F)Humidity: 30% to 80% RH (non-condensation)5. Dimensions and WeightDimensions:Approximately 110(W) × 100(D) × 49(H) mm (43⁄8"W × 4"D × 17⁄8"H)Weight: Approximately 154g (5.4oz)DT-X5_E_P59_70.p65 2004.10.1, 9:50 AM67
E-68Using Rechargeable Battery PackYour Handheld Terminal supports use of two battery pack types of different capacity. Youcan select the one that best suits your needs in terms of operating time, the type ofoptions you need to use, etc.When using the large-capacity battery pack, you need to use the special large-capacitybattery pack cover that comes with the Handheld Terminal.Important!Store a battery pack in its special soft case whenever you are not using it.Battery Pack SpecificationsModel: HA-A20BATRated Capacitance: 1700mAhRated Voltage: 3.7VDimensions:Approximately 37(W) × 57(D) × 13(H) mm (11⁄2"W × 21⁄4"D × 1⁄2"H)Weight: Approximately 45g (1.6oz)Bundled Item: Soft caseLarge-capacity Battery Pack SpecificationsModel: DT-5025LBATRated Capacitance: 3400mAhRated Voltage: 3.7VDimensions:Approximately 37(W) × 57(D) × 24(H) mm (11⁄2"W × 21⁄4"D × 1"H)Weight: Approximately 87g (3.1oz)Bundled Item: Soft caseDT-X5_E_P59_70.p65 2004.10.1, 9:50 AM68
E-69MemoDT-X5_E_P59_70.p65 2004.10.1, 9:50 AM69
E-70MemoDT-X5_E_P59_70.p65 2004.10.1, 9:50 AM70

Navigation menu