CastleNet Technology WM1260 Wireless 802.11g MiniPCI Card User Manual WM1260 Installation Manual

CastleNet Technology Inc. Wireless 802.11g MiniPCI Card WM1260 Installation Manual

Manual

Wireless 802.11g MiniPCI Card WM1260 OEM Installation Manual (The module is sold only to the OEM integrators & the manual is valid only for the OEM manufactures) Version: 1.0 December, 2004
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: This module is restricted to mobile configuration. To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter
*Caution !! (1). This module cannot be bound in a tablet computer for RF exposure issues. (See Label 1) (2). This module must be labeled with FCC ID. (See Label 2) Label 2 Label 1
(3). If the FCC ID is not visible when the module is installed inside another device, then the outside of device must also display a label referring to the enclosed module. The exterior label can be “ Contains Transmitter Module FCC ID:RK9-WM1260 ” or similar wording. (See label 3) Contains Transmitter WM1260 FCC ID: RK9-WM1260 Label 3 Please put Label 3 to the enclosure of end product to note the end user.
Wireless 802.11g MiniPCI Card WM1260 Installation Manual System Requirements Software (supports the following operating systems): o Windows XP o Windows XP SP1 o Windows 2000 o Windows ME o Windows 98SE Hardware: o Minimum configuration: Pentium 300 MHz, 128 MB RAM Hardware Installation For Window XP and Window 2000 Follow the steps below to install the WM1260 in your computer first. 1. Turn off the notebook PC. 2. Find the MiniPCI slot and open the cover. 3. Insert the WM1260 into the MiniPCI slot. Make sure the WM1260 contacts are fully seated in the MiniPCI slot. 4. Attach the antenna to the WM1260. 5. Cap the cover and power on the notebook PC. For Window ME and Window 98 WARNING : Setup must be run before the hardware is inserted into the system.
Software and Driver Installation Follow the steps for the appropriate version of Windows to install the Wireless 802.11g MiniPCI Card driver. Windows XP 1. When Windows automatically detects the Network Controller, click Cancel. 2. Insert the Driver CD into your CD-ROM drive. 3. Execute the setup.exe and then click Next. 4. When system appear the warning message, click Continue Anyway. 5. When system find the Broadcom 802.11g Network Adaptor, Click Continue Anyway.
6. Click Finish and reboot the system. Windows 2000 1. When Windows automatically detects the New Hardware, click Cancel. 2. Insert the Driver CD into your CD-ROM drive. 3. Execute the setup.exe and then click Next 4. When system appear the warning message, click Yes.
5. When system find the Broadcom 802.11g Network Adaptor, Click Yes 6. Click Finish and reboot the system. Windows ME WARNING : Setup must be run before the hardware is inserted into the system. 1. Insert the Driver CD into your CD-ROM drive. 2. Execute the setup.exe and then click Yes. 3. Click Next to continue the setup.
4. Click Finish and shutdown the computer when prompted. Notice : Insert the WM1260 when System is shutdown. After the hardware installed, power on the notebook. 5. When system find the Broadcom 802.11g Network Adaptor, Choose the Specify the location of the driver (Advance) and then Click Next. 6. Click Browse and find the driver BCMWL5.inf location then click Next 7. Click Next to continue the setup.
8. Click Finish. 9. Click Yes and reboot the system Windows 98 WARNING : Setup must be run before the hardware is inserted into the system. 1. Insert the Driver CD into your CD-ROM drive. 2. Execute the setup.exe and then click Yes. 3. Click Next to continue the setup. 4. Click Finish and shutdown the computer when prompted.
Notice : Insert the WM1260 when System is shutdown. After the hardware installed, power on the notebook. 5. Click Next to continue the setup. 6. Click Next to continue the setup. 7. Click Specify a location 8. Click Browse and find the driver BCMWL5.inf location then click Next 9. Click Next to continue the setup. 10. Click Yes and reboot the system
Configuration Follow the steps for the appropriate version of Windows to configure the Wireless 802.11g MiniPCI Card. Windows XP 1. Right-click on the Broadcom Wireless Configuration Utility icon in the Windows XP system tray and select Open Utility to open the utility options. 2. Select the Site Monitor tab and select the Network you want to use. 3. Select the Advanced tab if need configure more. 4. Double Click the Network name and then connect the Network. 5. Select the Link Status tab and you can check the link status.
Windows 2000/ME/98 1. Right-click on the Broadcom Wireless Configuration Utility icon in the Windows XP system tray and select Open Utility to open the utility options. 2. Select the Site Monitor tab and select the Network you want to use. 3. Select the Advanced tab if need configure more. 4. Double Click the Network name and then connect the Network. 5. Select the Link Status tab and you can check the link status.

Navigation menu