Cattron North America 7700P15 Industrial Remote Control Transmitter User Manual Paddle Controller Manual Rev 007a

Laird Controls North America Inc. Industrial Remote Control Transmitter Paddle Controller Manual Rev 007a

user manual

 ©03/2007, CATTRON-THEIMEG™    - i - PADDLE CONTROLLER OPERATION & MAINTENANCE INSTRUCTIONS     CUSTOMER: MODEL NUMBER:   SERIAL NUMBER: FREQUENCY ASSIGNMENT: ADDRESS ASSIGNMENT: MANUAL P/N:            68C-Paddle Rev. 006, 03/2007
 ©03/2007, CATTRON-THEIMEG™    - i - FCC and IC Statements FCC and IC labeling can be found inside the user accessible lid of the battery compartment where it is protected from damage. FCC Warning Statements Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment For Low Power License Exempt Units FCC Warning Statements Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  interference  when  the  equipment  is  operated  in  a  commercial  environment.  This  equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the  instruction  manual,  may  cause  harmful  interference  to  radio  communications.  Operation  of  this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.  This  device  complies  with  Part  15  of  the  FCC  rules.  Operation  is  subject  to  the  following  two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. IC Warning Statements This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada
 Page ii    ©03/2007, CATTRON-THEIMEG™  IMPORTANT NOTICES Your new paddle controller has been pre-configured to operate on a specific frequency before leaving our factory which cannot be changed by yourselves.  We have assigned this frequency based upon our existing  records  of  control  equipment  previously  supplied  to  yourselves.    However,  we  strongly recommend you satisfy yourselves that the frequency of your paddle controller does not match that of any other radio remote control system located at, or around, your operating facility.        WARNING: CATTRON-THEIMEG™  MAKES  EVERY  EFFORT  TO  ENSURE  THE ADDRESS  ASSIGNED  TO  YOUR  NEW  CONTROL  SYSTEM  IS  NOT DUPLICATED BASED UPON RECORDS WHICH INDICATE THE ADDRESSES OF ALL PAST PORTABLE RADIO REMOTE CONTROL (PRRC) SYSTEMS AS SHIPPED FROM OUR FACILITY TO YOURS.   THEREFORE IT SHOULD BE FULLY UNDERSTOOD THAT WHEN A PRRC SYSTEM  HAS  LEFT  OUR  FACTORY,  CATTRON-THEIMEG™  HAS  NO CONTROL  OF  THE  ADDRESS  ASSIGNMENTS  OF  ANY  OTHER  PRRC SYSTEM(S) THAT MAY BE IN OPERATION IN CLOSE PROXIMITY WITHIN YOUR OPERATING AREA.   CONSEQUENTLY,  AND  PURSUANT  TO  THE  ABOVE  STATEMENT, CATTRON-THEIMEG™  SHALL  NOT  BE  HELD  LIABLE  FOR  PERSONAL INJURY,  DEATH,  EQUIPMENT  OR  PROPERTY  DAMAGE  ARISING  FROM DUPLICATED ADDRESSES OF RADIO CONTROL SYSTEMS.
 ©03/2007, CATTRON-THEIMEG™    - iii -  OPERATION & MAINTENANCE INSTRUCTIONS IMPORTANT NOTICES, continued.  Your Remote Control System may include an optional ‘Reset’ function that must be activated from the remote controller before motion control outputs are enabled on the controlled machine.  You are advised to review the customized drawing package provided with your Portable Remote Control (PRC) system to see if this optional safety feature applies to your PRC system.  Alarm (     )/optional‘Reset’ (   ) FunctionPushbuttonControllerPTO Bar   When this ‘Reset’ function applies to your PRC system, the momentary Alarm/Reset pushbutton located in  the  center  of  the  controller’s  PTO  bar  must  be  depressed  immediately  after  the  controller  has completed its Power On Self Test, and before holding the PTO bar down to activate a motion control function.    This  will  sound  the  system  horn  (when  connected)  and  reset  the  Main  Equipment  Power Contactor.  This  equipment  is  firmware  based,  including  encoder,  decoder,  transmitter,  and  receiver.  Any duplication  of  operating  firmware  without  written  consent  of  CATTRON-THEIMEG™  is  prohibited.  All firmware, product listings, assembly files, and this manual are protected by U.S. Copyright Laws.  As part of our continuous improvement policy, CATTRON-THEIMEG™ reserves the right to change specifications without notice.
 Page iv    ©03/2007, CATTRON-THEIMEG™ List of Technical Abbreviations The  following  abbreviations  (acronyms)  are  frequently  used  in  CATTRON-THEIMEG™  Radio Remote Control Technology and may be used in this manual:  AC  Alternating Current    LED  Light Emitting Diode ASO  Automatic Safety Override   MK  Metal Keypad BCH  Bose-Chaudhuri-Hocquenghem (data error detection routines)   ML  Mainline CMOS  Complimentary Metal Oxide Semiconductor    NEMA  National Electrical Manufacturer’s Association CS  Crane Specific    Ni-Cad  Nickel Cadmium DC  Direct Current    OPR  Operate DOC  Department of Communication    PRC  Portable Remote Control DP  Dual Pressure    PTO  Push-to-Operate  EDP  Electronic Data Processing    RF  Radio Frequency EEPROM  Electrically Erasable Programmable Read Only Memory   RFI  Radio Frequency Interference EMI  Electro-Magnetic Interference    RST  Reset Relay EOT  Electrical Overhead Traveling    SP  Single Pressure EPROM  Erasable Programmable Read Only Memory    SYNC  Synchronization FCC  Federal Communications Commission    TS  Transfer Switch GND  Ground    VAC  Volts Alternating Current  I/O  Input/Output    VDC  Volts Direct Current  LCD  Liquid Crystal Display    VFD  Variable Frequency Drive
 ©03/2007, CATTRON-THEIMEG™    - v - Introduction How to use this Manual. This manual contains generic operation and maintenance procedures applicable to the entire series of CATTRON-THEIMEG™ Radio Remote Paddle Controllers.    Because no two Paddle Controllers or Portable Remote Control (PRC) applications are exactly the same, a  General  Operating  Procedure  is  included  in  Section  3.    This  procedure  is  followed  by  Operator Instructions  for  the  two  most  popular  control  applications:  (1)  Cranes,  and  (2)  Locomotives.    By selecting  the  application  (1)  or  (2)  closest  to  your  PRC  system,  you  should  be  able  to  familiarize yourself with the basic operating procedures and control functions that apply to your system.   We  emphasize  that  safety  considerations  are  paramount  when  using  portable  remote  controllers.  Accordingly,  Section  2  should  be  read  in  its  entirety.    Also,  for  your  consideration  and  possible adoption, Recommended Safety Rules for Remote Controlled Cranes, and Recommended Safety Rules for Radio Remote Controlled Locomotives are provided as an addendum at the end of this manual.
 Page vi    ©03/2007, CATTRON-THEIMEG™ Safety Summary  WARNING  and  CAUTION  statements  have  been  strategically  placed  throughout  all  text  prior  to operating or maintenance procedures, practices or conditions considered essential to the protection of personnel (WARNING), or equipment and property (CAUTION).  A WARNING and CAUTION will apply each time the related step is repeated.  Before starting any task, the WARNINGS or CAUTIONS included in the text for the task shall be reviewed and understood.  All WARNINGS and CAUTIONS appearing in this manual are included below. WARNINGS.     WARNINGS: WITH  THE  EXCEPTION  OF  LOCOMOTIVES,  ALL  EQUIPMENT  MUST HAVE A MAINLINE (ML) CONTACTOR INSTALLED AND ALL TRACKED EQUIPMENT (i.e. CRANES) HAVE A BRAKE INSTALLED. THE REMOTE CONTROL OPERATE (OPR) RELAY MUST BE CONNECTED TO THE MAINLINE SO THAT STOP COMMANDS OR FAULT CONDITIONS MONITORED  BY  AUTOMATIC  SAFETY  OVERRIDE  (ASO)  CIRCUITRY WILL  DE-ENERGIZE  THE  MAINLINE  CONTACTOR  AND  SET  THE EQUIPMENT BRAKE.  FAILURE TO COMPLY WITH THE ABOVE WARNINGS MAY RESULT IN SERIOUS  INJURY  OR  DEATH  TO  PERSONNEL  AND  DAMAGE  TO EQUIPMENT.       WARNING: MORE  THAN  ONE  REMOTE  CONTROL  SYSTEM  MAY  BE  USED  AT, AROUND, OR NEARBY YOUR OPERATING FACILITY.  THEREFORE, YOU MUST  INSURE  THE  ADDRESS  CODE  AND  FREQUENCY  OF  YOUR PADDLE CONTROLLER EXACTLY MATCHES THE ADDRESS CODE AND FREQUENCY OF THE DESIRED EQUIPMENT TO BE OPERATED. FAILURE  TO  COMPLY  WITH  THE  ABOVE  WARNING MAY  RESULT  IN THE  UNDESIRED  OPERATION  OF  OTHER  EQUIPMENT  WHICH,  IN TURN, COULD RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.      WARNING: NEVER DISABLE THE PUSH TO OPERATE (PTO) BAR SWITCH ON YOUR REMOTE CONTROLLER.  FAILURE TO COMPLY WITH THIS WARNING MAY  RESULT  IN  DAMAGE  TO  EQUIPMENT,  SERIOUS  INJURY,  OR DEATH.
 ©03/2007, CATTRON-THEIMEG™    - vii - WARNINGS, continued.     WARNING: ON CAB AND REMOTE OPERATED CRANES OR CARRIERS AN AUDIBLE OR VISUAL WARNING MEANS SHALL BE PROVIDED.  IN ADDITION, ALL EQUIPMENT  SHALL  HAVE  AUDIO  OR  VISUAL  ALARM  INDICATIONS MEETING  GOVERNMENTAL  REQUIREMENTS.  FAILURE  TO IMPLEMENT  THIS  WARNING  MAY  RESULT  IN  SERIOUS  INJURY  OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.     WARNINGS: UNCODED  ADDRESS  PLUG(S)  SHALL  BE  PROGRAMMED  WITH  THE SAME  ADDRESS  CODE  AS  SET  IN  THE  TARGET  RECEIVER/DECODER.   IT  SHOULD  BE  FULLY  UNDERSTOOD  THAT  CATTRON-THEIMEG™ SHALL  NOT  BE  HELD  LIABLE  FOR  PERSONAL  INJURY,  DEATH, EQUIPMENT  OR  PROPERTY  DAMAGE  ARISING  FROM  DUPLICATED, INCORRECTLY PROGRAMMED OR INCORRECT CODE PLUG USAGE. IT  IS  YOUR  RESPONSIBILITY  TO  ESTABLISH  A  PROCEDURE  THAT INSURES  ONLY  THE  CODE  PLUG  CONFIGURED  FOR  A  PARTICULAR ADDRESS  IS  INSTALLED  IN  EQUIPMENT  DESIGNED  TO  OPERATE  ON THE  SAME  ADDRESS.    NEVER  PUT  MORE  THAN  ONE  CONTROLLER INTO  OPERATION  ON  THE  SAME  ADDRESS  AT  ANY  GIVEN  TIME.  CATTRON-THEIMEG™ STRONGLY ADVISES YOU  TO IMPLEMENT  AND REGULARLY  UPDATE  A  REGISTER  OF  INDIVIDUAL  ADDRESSES  AND OPERATING  FREQUENCIES  ASSIGNED  TO  EACH  PORTABLE  RADIO REMOTE  CONTROL (PRRC)  SYSTEM  LOCATED AT  YOUR  OPERATING FACILITY.   IN ADDITION, ANY SPARE CODE PLUGS, OR CODE PLUGS INSTALLED  IN  EQUIPMENT  THAT  ARE  CONFIGURED  FOR  THE  SAME ADDRESS OF EQUIPMENT THAT IS IN SERVICE, MUST BE HELD UNDER LOCK AND KEY BY A DESIGNATED SUPERVISOR.   FAILURE  TO  COMPLY  WITH  THESE  WARNINGS  MAY  RESULT  IN OPERATION  OF  UNDESIRED  EQUIPMENT  WHICH  IN  TURN  COULD RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.
 Page viii    ©03/2007, CATTRON-THEIMEG™ WARNINGS, continued.     WARNINGS: ALL TRACKED EQUIPMENT (i.e. LOCOMOTIVES) MUST HAVE A BRAKE INSTALLED. THE  REMOTE  CONTROL  OPERATE  (OPR)  RELAY  MUST  BE CONFIGURED  SO  THAT  STOP  COMMANDS  OR  FAULT  CONDITIONS MONITORED  BY  AUTOMATIC  SAFETY  OVERRIDE  (ASO)  CIRCUITRY WILL SET THE THROTTLE TO IDLE, DISCONNECT  THE  GENERATOR FIELD, AND SET THE INDEPENDENT BRAKE.  FAILURE TO COMPLY WITH THE ABOVE WARNINGS MAY RESULT IN SERIOUS  INJURY  OR  DEATH  TO  PERSONNEL  AND  DAMAGE  TO EQUIPMENT.       WARNING: AFTER CHANGING AN ADDRESS OR FREQUENCY SELECTOR SWITCH, YOU  MUST,  IN  THE  FIRST  INSTANCE,    INSURE  THE  TARGETED MACHINE  IS  UNDER  REMOTE  CONTROL  BEFORE  OPERATING  ANY MOTION  FUNCTION  SWITCH.    THIS  MAY  BE  ACCOMPLISHED  BY OPERATING  A  NON  MOTION  FUNCTION  SWITCH  ON  THE  REMOTE CONTROLLER SUCH AS A HORN OR LIGHT.  FAILURE  TO  COMPLY  WITH  THE  ABOVE  WARNING  MAY  RESULT  IN THE  UNDESIRED  OPERATION  OF  OTHER  EQUIPMENT  WHICH,  IN TURN, COULD RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.       WARNING: ELECTRICAL  POWER  TO  THE  TARGET  CONTROLLED  EQUIPMENT MUST  BE  COMPLETELY  ISOLATED  TO  PREVENT  OPERATION  UNDER REMOTE CONTROL IN THE SWITCH DIAGNOSTIC MODE.  FAILURE  TO  COMPLY  WITH  THE  ABOVE  WARNING  MAY  RESULT  IN THE UNDESIRED OPERATION OF EQUIPMENT WHICH, IN TURN, COULD RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.
 ©03/2007, CATTRON-THEIMEG™    - ix - WARNINGS, continued.     WARNING: DUE  TO  FCC  PART  15  AND  DOC  RSS-210  RADIO  TRANSMIT REGULATIONS,  THE  OPR  OUTPUT  TO  WHICH  YOUR  CONTROLLED EQUIPMENT’S MAINLINE CONTACTOR IS CONNECTED WILL REMAIN ENERGIZED FOR TEN MINUTES AFTER THE CONTROLLER POWER IS SET  TO  ‘OFF’,  OR  FOR  TEN  MINUTES  AFTER  THE  LAST  TIME  A FUNCTION SWITCH IS ACTIVATED.  CONSEQUENTLY, SPECIAL CARE MUST BE TAKEN IF THE CRANE OR TRACKED MACHINE IS EQUIPPED WITH A PARKING BRAKE  THAT  IS CONFIGURED TO ENGAGE  WHEN THE MAINLINE CONTACTOR DE-ENERGIZES.    TO PREVENT A POTENTIALLY HAZARDOUS SITUATION, YOU SHOULD IMMEDIATELY  SELECT  THE  RED  ‘STOP’  FUNCTION  ON  YOUR REMOTE CONTROLLER AFTER COMPLETION OF OPERATIONS.  SUCH ACTION  WILL  INSURE  THE  PARKING  BRAKE  (IF  EQUIPPED  AND CONFIGURED  AS  ABOVE)  IS  SET,  PREVENTING  UNINTENTIONAL MOVEMENT OF THE CRANE OR TRACKED MACHINE. FAILURE TO COMPLY WITH THIS WARNING MAY RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.    CAUTIONS.   CAUTIONS: (1) CATTRON-THEIMEG™  Battery  Conditioners  are  designed  for  use  with CATTRON-THEIMEG™ Ni-Cad Battery Packs only.   (2) Battery Packs must be removed or disconnected from Battery Conditioners within 48-hours of achieving the fully charged state.   Failure to comply with these Cautions  may result in equipment and/or battery damage and will void our warranty.    NOTE.   Important Safety Note: When  using  the  controller,  operators are  instructed  to  wear  a factory  approved carrying harness with the controller attached at all times.  If a controller must be left  unattended,  the  STOP  switch  (when  installed  to  the  controller)  should  be depressed and the controller’s power ON/OFF switch set to ‘OFF’.  If the power ON/OFF  switch  is  a  key  switch,  the  key  should  also  be  removed  to  prevent unauthorized use of the controller.
 Page x    ©03/2007, CATTRON-THEIMEG™ Safety Summary, continued.  GENERAL. The following are general safety precautions that are not related to any specific procedure and therefore do  not  appear  elsewhere  in  this  manual.    These  are  general  safety  precautions  and  instructions  that people must understand and apply during many phases of operation and maintenance to ensure personal safety and health and the protection of your company property.  KEEP  AWAY  FROM  LIVE  CIRCUITS.    Maintenance  personnel  must  observe  all  safety requirements at all times.  Do not replace components or make adjustments inside the equipment with the electrical supply turned on.  Under certain conditions, danger may exist even when the power control is in the off position due to charges retained by capacitors.  To avoid injuries, always remove power, discharge and ground a circuit before touching it.  Adhere to all lock out/tag requirements.   DO NOT SERVICE OR ADJUST ALONE.  Whenever possible, do not attempt internal service or adjustment of equipment unless another person capable of rendering aid and resuscitation is present.   FINGER  RINGS/JEWELRY.    Finger  rings  have  caused  many  serious  injuries.    Remove  rings, watches and other metallic objects which may cause shock or burn hazards.     SOLDERING/DE-SOLDERING.    Avoid  breathing  fumes  generated  by  soldering/de-soldering. Perform all operations in a ventilated area.  Eye protection is required.   CLEANING SOLVENTS.  Some cleaners and solvents have adverse effects on skin, eyes, respiratory tract  and  internal  organs.    These  adverse  effects  range  from  discomfort  to  serious  injury  and  death, depending on the material and degree of exposure.  Observe manufacturers’ warning labels and contact your immediate supervisor if in any doubt.   Remember…. the person now reading these instructions is  primarily  responsible  for  his  or  her  own  health  and safety.
 ©03/2007, CATTRON-THEIMEG™    - xi -        This page intentionally left blank
 ©03/2007, CATTRON-THEIMEG™    - i - Table of Contents Front Matter:  FCC and IC Warnings……………………………………………………………………i Important Notices ……………………………………………………………………ii-iii List of Technical Abbreviations .................................................................................... i v How to use this Manual  .................................................................................................. v Safety Summary warnings and cautions..................................................................... vi-x Section 1 – Product Data and Specifications: Introduction .................................................................................................................  1-1 Notable Performance and Safety features ...................................................................  1-2 Frequently asked questions .........................................................................................  1-3 Standard Specifications ...............................................................................................  1-5 Overview of CATTRON-THEIMEG™ Remote Control Systems ..............................  1-7 Section 2 – Safety Information: Safety Considerations  .................................................................................................  2-1 Safety and Security Features ...........................................................................  2-1 Typical Method of Operation incorporating ...................................................  2-2 Safety & Security Features Radio Control Operator’s Duties – General Equipment .............................................  2-4 Radio Control Operator’s Duties – E.O.T. Crane .......................................................  2-8 Radio Control Operator’s Duties – Locomotive .......................................................  2-12 Section 3 – Operating Instructions: Controls and Indicators ...............................................................................................  3-1 General Operating Procedure ......................................................................................  3-5 Typical Crane Control Functions ..............................................................................  3-10 Typical Locomotive Control Functions ....................................................................  3-13 Switch Diagnostic Mode ...........................................................................................  3-17
 Page ii    ©03/2007, CATTRON-THEIMEG™ Section 3 – Operating Instructions, continued: Battery Packs and Battery Pack Charging  ................................................................  3-18   Battery Pack Replacement  ............................................................................  3-18   Battery Pack Conditioning/Charging – Ni-Cad Battery packs only  .............  3-20 Pre-Programmed Frequency Selection  .....................................................................  3-22 Pre-Programmed Option Selection  ...........................................................................  3-25 Section 4 – Maintenance Instructions: CATTRON-THEIMEG™ Maintenance Philosophy ...................................................  4-1 Preventive Maintenance ..............................................................................................  4-1 Troubleshooting ..........................................................................................................  4-2   Troubleshooting Guide  ...................................................................................  4-3 Corrective Maintenance ..............................................................................................  4-4 Functional Check  ........................................................................................................  4-4 Replacement Items ......................................................................................................  4-4   Battery Pack ....................................................................................................  4-4   Address Code Plug ..........................................................................................  4-5   Side Lever (optional item)  ..............................................................................  4-9   External Antenna (optional item) ..................................................................... 4-9 Section 5 – Replacement Items and Accessories: Replacement Items  .....................................................................................................  5-1 Consumable Items and Optional Accessories .............................................................  5-5 Index. Appendices: 1.  RECOMMENDED SAFETY RULES FOR PORTABLE REMOTE CONTROLLED (PRC) CRANES. 2.  RECOMMENDED SAFETY RULES FOR PORTABLE RADIO REMOTE CONTROLLED (PRRC) LOCOMOTIVES.
 ©03/2007, CATTRON-THEIMEG™    Section 1, Page 1 Section 1 – Product Data & Specifications  Introduction. The CATTRON-THEIMEG™ Paddle Controller has a unique shape and style that provide the equipment operator  with  a  controller  that  is  extremely  durable,  convenient,  and  easy  to  operate.    Designed specifically for  heavy duty  in harsh working  environments, the controller  is  ideally suitable for both indoor  and outdoor  remote control  applications  within  the steel,  glass, automotive,  shipping, mining, distribution, and railroad industries.  It can be used with all CATTRON-THEIMEG™ AT Series or MP Series  receiver/decoder  units  as  well  as  being  used  with  existing  CATTRON-THEIMEG™ PRRC systems as either a replacement or spare controller.   Your  paddle  controller  is  designed  to  duplicate  the  operating  characteristics  of  the  controls  most commonly found on the controlled machine, therefore the change from manual to radio remote control is easily learned by the operator.  The  CATTRON-THEIMEG™  paddle  controller  employs  advanced  micro-computer  electronics  and utilizes surface mount technology.   A highly advanced encoder  circuit board is built using industrial grade  components  and  incorporates  a  powerful  microcomputer  that  uses  sophisticated  operating software. The main housing that surrounds and protects the electronic circuitry is made of thick walled, extruded aluminum with a protective exterior coating. The ends of the housing are rubber-coated plates that make shock absorbing end ‘bumpers’ and switch/lever guards.  Only the highest quality industrial grade  and  ‘mil-spec’  switches  whose  reliability  and  construction  have  been  field-tested  and  proven under extreme conditions are used in your paddle controller.   Total water and dust sealing makes these switches suitable for indoor and outdoor operation.   CATTRON-THEIMEG™ paddle controllers have room for up to six paddles and can be customized with additional pushbuttons and toggle switches.  In addition, all functions are identified by durable custom engraved nameplates.  A variety of synthesized and crystal-controlled RF transmitter configurations can be provided with this controller, allowing operation on licensed and non-licensed VHF and UHF radio channels. In addition, all CATTRON-THEIMEG™ paddle controllers meet the FCC's requirements regarding narrow band and 12.5 kHz bandwidths.
 Section 1, Page 2    ©03/2007, CATTRON-THEIMEG™ Notable Performance and Safety Features. POWER ON SELF TEST (POST) DIAGNOSTICS - When the operator first turns the power switch on, a  sophisticated  self-test  routine  tests  the  microcomputer  and  all  function  switch  inputs  to  detect unwanted commands in the system.   All lever style switches are tested for neutral at this time.  A small speaker beeps twice when the test has been completed satisfactorily. TRANSMIT/BATTERY  CHARGE  INDICATOR  -  The  low  battery  detection  circuit  is  a  two  stage design.  With a good battery, this indicator light flashes green for each burst of transmitted data.  If the battery voltage drops below the normal level, this LED flashes red during each transmission.  A beeping sound every 10 seconds alerts the operator.  When this happens, the battery has approximately one hour of  operating  time  remaining.  The  controller stops  transmitting  before  the  voltage  drops  so  low  that erratic operation could occur.   BATTERY  SAVER  –  If  the controller  has not  been operated  for 15  minutes, a  battery  management system detects this inactivity and puts the controller into a ‘deep sleep’ mode.  To reset the controller, the POWER ON/OFF SWITCH must be set to ‘OFF’, and then set to ‘ON’ again. BATTERY  PACK  OPTIONS  –  Alkaline  (disposable)  &  Ni-Cad  (rechargeable)  battery  packs  are available  from  CATTRON-THEIMEG™.      Whether  you  choose  disposable  or  rechargeable  battery packs, changing the battery pack is easy - simply unlatch and open the gasketed battery door, drop the battery pack in place and close and latch the battery door.  There are no wires or connectors to insert into the battery pack, which improves long-term reliability of this unit. RUGGED HOUSING - The housing that surrounds and protects the electronic circuitry is a thick-walled extruded aluminum, which has a hard epoxy powder coated exterior.  The ends of the housing are rubber coated plates that make shock absorbing end 'bumpers’. DURABLE/OUTDOOR  OPERATION  –  All  switches  are  extremely  long  life  units  that  are  sealed, providing  water  and  dust  protection.    All  modules  and  sub-components  are  gasketed,  making  your controller suitable for outdoor operation in rain and snow. LEVER  AND  SWITCH  PLACEMENT  -  Each  layout  is  customized  according  to  user  needs.    The switch levers are placed far enough apart to accommodate operators who wear heavy gloves. SAFETY BAR - A long safety bar is provided to function as an  enable device to  all motion control switches.    It  is  a  large  full-length  switch  that  is  easily  and  naturally  activated  by  a  convenient  and comfortable part  of the  operator's hand  any time he or she activates a motion switch.  This push-to-operate  (PTO)  safety  bar  electronically  disconnects  all  motion  switches  when  it  is  released,  thus stopping motion commands from these switches.  This feature is programmable as some applications may have lever switches removed from control of the PTO bar.  An example of this would be some locomotive braking functions. ALARM/RESET  FUNCTION  (optional)  –  Your  remote  controller  may  incorporate  this  additional safety function connected to the momentary pushbutton located in the center of the PTO Safety Bar.   Check the system drawings provided with  your  remote  control  system to see if this  optional  feature applies  to  your  controller.    When  applicable  to  your  controller,  this  pushbutton  must  be  depressed immediately after the controller has completed its Power On Self Test and before holding the PTO Bar down to activate a motion control function.  This will sound the system horn (when connected) and reset the main Equipment Power Contactor.
 ©03/2007, CATTRON-THEIMEG™    Section 1, Page 3 Notable Performance and Safety Features, continued. LEVER GUARD BAR (optional) – When additional lever switch protection against physical damage is required, this fixed bar extends upwards from both ends and across the front of the controller. INTERNAL TILT SWITCH – If the controller is tilted in any axis beyond 60 degrees of upright for longer than the programmed time (typically 3 seconds), a programmable function is sent automatically.  This function can be assigned in the decoder to stop the equipment, sound an alarm, or both.  Reset time is also programmable. OPERATING  FREQUENCIES  -  A  variety  of  RF  transmitters  are  available  allowing  controller operation in 72-76 MHz, 402-420 MHz, and 450-470 MHz bands on licensed radio channels and 447-471 MHz on unlicensed channels.  Most models in the 450 MHz range are synthesized (16 frequency channels maximum). APPLICATIONS  -  The  paddle  controller  can  operate  any  digital  series  receiver/decoder  built  by CATTRON-THEIMEG™.    It  can  be  used  with  existing  CATTRON-THEIMEG™ systems  as  a replacement or as an extra transmitter/encoder. Frequently Asked Questions. Refer to Table 1-1 below for the most frequently asked questions about your paddle controller.   Table 1-1.  Paddle Controller, questions and answers QUESTION  ANSWER SAFETY   Protection against operator becoming disabled or falling down?  YES - fitted with a tilt switch and Push to Operate (PTO) safety bar switch as standard Protection against accidental switch operation?  YES - PTO safety bar switch and toggle switches are protected by housing  design.  Spring return to OFF  Simple operation by position and feel (without looking at controller)?  YES -  Levers are large enough for easy glove operation.  Unique shape knobs available.  Detent for speed steps (5) High quality custom labeling?  YES – Customized text and arrows, large size, durable mylar Number of functions sent to activate a motion?  TWO  (lever and PTO) Protection against false commands or data as battery discharges?  YES - Low battery warning, then cut off prior to reaching unstable levels Protection against stray radio signals and other Remote Control systems?  YES - Unique digital address sent at the beginning of each data message. Protection against other digital data radio (e.g.. pagers, cell, fax) or radiation from computer equipment? YES - Unique (non-standard) data baud rate, each motion command has data in at least two bytes, very complex data error detection (BCH)  Protection against broken switches or wiring sending motion commands?  YES - Switches (potentiometers) are tested for neutral at power on and for open or shorted wiring before each digital message. Potentiometers tested for travel beyond end of range and digital A/D converters tested constantly  Withstand static discharge and high magnetic fields?   YES - Unit tested for EMI/RFI by independent lab.  Passes and can carry CE mark.  Has been used successfully in high magnetic fields.
 Section 1, Page 4    ©03/2007, CATTRON-THEIMEG™ Frequently Asked Questions, continued. Table 1-1.  Paddle Controller, questions and answers QUESTION  ANSWER RELIABILITY   Durable case material?  YES - Aluminum with epoxy coating.  ‘Neoprene’ rubber bumper ends Enclosure water/dust/oil resistant?   YES - NEMA 12 (IP-65) Long motion switch operating life?  YES – Greater than 1 million operations Reliable switch wiring?  YES – Switches are potentiometers, wired using silver coated multi-strand teflon coated wire and gold plated connectors. Only 3 wires per ‘switch’  Simple and reliable electrical connection method to battery?   YES - Stainless steel contacts that mate with stainless pads on battery. Automatic wiping at each insertion into controller Ability to survive repeated drops on to concrete floor?   YES - Tested by UL labs to mil-specs.  Drops will not cause motion Maximum number of function speed steps per motor available?  Uses potentiometers for all motion functions - 5 step each direction or stepless typical State of the art electronic construction techniques?  YES - Machine built PC board (1) using surface mount components primarily MAINTAINABILITY   High quality component grades used?  YES - Industrial and mil-spec Internal antenna?  YES – Slot design, printed circuit board construction, integral part of lower front housing on unlicensed controllers.  Optional external antennas available. Operator diagnostics - battery condition indication?  YES - TWO stage battery condition indicator: flash GREEN – OK.  Flash RED – battery needs changing, audible beeps every 10 seconds anytime red indicator is flashing. Operator diagnostics - determining switch operation condition?  YES - Can be placed in switch beep mode by turning on power while unit is tilted. Beep when a motion control function switch is operated indicates switch functioning correctly. Data transmit indicator?  YES – GREEN LED flashes with each message being sent (will normally be synchronized with receiver LED's) Easy Disassembly and Assembly?   YES - by CATTRON-THEIMEG™ trained customer technicians only. Minimal wires and few connections PC diagnostics capability?  YES - by CATTRON-THEIMEG™ trained customer technicians only.   PC testing port, cable, and diagnostic software available. Helps real time troubleshooting  Test method for RF frequency, modulation and related tests?  YES - by CATTRON-THEIMEG™ trained customer technicians only. Unit can be placed in a special test mode by holding PTO bar down while turning on power (also prevent operator tampering)
 ©03/2007, CATTRON-THEIMEG™    Section 1, Page 5 Frequently Asked Questions, continued. Table 1-1.  Paddle Controller, questions and answers QUESTION  ANSWER OPERATIONAL FEATURES   FCC approval for narrow band licensed operation in new 12.5 kHz channels? YES - Approved for both non-licensed and licensed services with ongoing designs for changing USA and Canadian rules and regulations. Transmitters can be assigned 12.5kHz channels.  In addition, units have a wide number of approvals and frequency ranges for European, UK  and Australian operation Operational  range without Close Start or Range limited receiver /decoder (Maximum distance)? Low power (unlicensed) units typically 300 feet for operation indoors in an industrial environment. 500 feet outdoors under best conditions  Licensed units typically 800 to 1000 feet indoors.  Higher power M840 option is available for operation up to 1 mile outdoors,  depending on a variety of operational and environmental factors which may reduce the actual operating range.  A typical example of the above would be a locomotive application with TALKBACK™ operating at 330 mW using an ‘on board’ 5dB antenna.    Special display features for operator?   YES - LED (day/night) optional - selects data to be sent e.g., door number to control.  LCD or individual LED's available for Talkback  Weight?  3-paddle unit (P03) weighs approximately 6.5 pounds with battery pack.  Optional lightwieght end-caps available which will reduce weight by 1 lb Carrying methods available to provide comfortable, (all day) operation? YES - Normally carried using a belt and shoulder harness combination. This places the unit at the belly. A back support (wide elastic) belt and shoulder harness combination is optional Standard Specifications. Case Material:  Epoxy  powder  coated  Anodized  Aluminum  Extrusion  with  Molded Rubber End Caps.   Weight:  3-Paddle Unit  (P03) -  approximately 6.5 lbs.  (3 Kgs),  including Battery Pack. Dimensions:  3-Paddle Unit (P03) - Height: 5.9" (15 cm) Depth: 6.7" (17 cm) Width: 9.5" (24 cm). Environmental:  -4° F to +140° F (-20° C to +60° C),  RH 0 to 95% Non-condensing. Switch Types:  Spring  Return  to  Center  Toggle,  Maintained  Toggle,  Momentary Pushbutton, Rotary Select. Lever Switch  Detented (5-steps each side of center) or Stepless (analog) Spring Forward Choices:  Idle and 8-steps for Throttle, Etc. Lever Styles:  Large Flag. Special Shaped Lever Knobs Optional.
 Section 1, Page 6    ©03/2007, CATTRON-THEIMEG™ Standard Specifications, continued.  Number of Motor  3  (3-Paddle),  4  (4-Paddle),  5  (5-Paddle),  or  6  (6-Paddle).  Additional Functions:         motor functions are available – contact your CATTRON-THEIMEG™ sales representative for details Auxiliary Functions:    15 digital ON/OFF.  Push To Operate Safety Bar:    Standard.  Lever Guard Bar:  Optional – extends from both sides across the front above the levers.  Labeling:    Mylar, Multi-layer, Large  Keylock Switch:  Optional (Power ON/OFF).  Antenna:    Internal (external antenna optional on licensed versions only).  Low Battery Indicator:    2 Color LED:  GREEN - Battery Normal, RED - Battery Low.  Short Circuit Protection:    Automatically Resettable Polyswitch (no fuses).  Conformal Coating:  Standard on PC Board.  Transmitter Frequency:    Synthesized and Crystal Control Models       72-76 MHz, 402-420 MHz, or 450-470 MHz - License Required.       447-471 MHz - No License Required.  Power Output:   450-470 MHz: typically between 20 and 40 mW.        402-420 MHz: typically between 20 and 40 mW.       72-76 MHz: 60 mW Nominal.       447-471 MHz: Maximum According to FCC Rules Part 15.       402-420 MHz, or 450-470 MHz M840 transmitter/transceiver (licensed) option adjustable from 80-450 mW  Synthesized Channels:    16 Maximum (Factory Programmed).
 ©03/2007, CATTRON-THEIMEG™    Section 1, Page 7 Overview – CATTRON-THEIMEG™ Radio Remote Control Systems Figure 1-1 below shows a simplified block diagram of a typical CATTRON-THEIMEG™ radio remote control  system.  Refer  to  this  figure  and  the  following  paragraphs  for  a  functional  description  of  the remote control system. The  target  receiver/decoder  is  controlled  by  the  Paddle  Controller,  which  sends  signals  to  the receiver/decoder using a UHF radio link.  The signal is picked up by the antenna and passed on to the receiver.  Provided the frequency of the paddle controller exactly matches that of the target receiver and passes all data tests, the signal is passed on to the decoder. The decoder compares the address code of the signal to its own address code. If the signal’s address code does not match the decoder’s address code, it is ignored and a message is displayed on a system status display usually located in the receiver/decoder unit.  If the address code is correct, the decoder processes  the  message and  energizes and de-energizes the appropriate control  and auxiliary  function relays located within the control system.  An Automatic Safety Override (ASO) function continually monitors the state of any directional relay output (i.e. Forward/Reverse). If a monitored relay electrically fails closed without a command from the controller, the ASO circuit logic de-energizes the master output relay (OPR) which should be connected to the mainline contactor of your controlled machine. During  operation,  the  microprocessor  on  the  decoder  board  resets  multiple  watchdog  timer  circuits whenever valid messages are received and decoded.  If the microprocessor fails to reset the watchdog timers,  the  timer  circuits  shut  down  and  de-activate  all  relay  outputs.  The  decoder  microprocessor requires continuously valid transmitted signals to be received and decoded or all relay output functions will be de-activated unless programmed otherwise. It should be noted that the mainline  control relay (OPR) may be maintained for up to 10 minutes, depending on system configuration. Figure 1-1. Typical Radio Remote Control System  - simplified block diagram CONTROLLERADDRESS ADDRESS FREQFREQRxTxRECEIVERMACHINE WIRINGDECODER12 VDCPOWERSUPPLYWATCHDOGTIMERMAINS INPUT50-60 HZAUXILIARY FUNCTIONOUTPUT RELAYSDIRECTIONALOUTPUT RELAYSASO END OF SECTION
 Section 1, Page 8    ©03/2007, CATTRON-THEIMEG™         This page intentionally left blank
 ©03/2007, CATTRON-THEIMEG™     Section 2, Page 1 Section 2 – Safety Information Safety Considerations. CATTRON-THEIMEG™ believes that to safely operate any remotely controlled equipment, the overall system needs to be configured so that movement  or operation of the equipment will take place  only when the device is commanded to move or operate.  For example, overhead cranes or locomotives must be equipped  with a braking system  that can only be  released when an electrical signal is  sent to the motor.  Removal of electrical power or loss of the radio transmitted signal results in application of the brakes.  On cranes, this is provided when a CATTRON-THEIMEG™ Electro-Hydraulic brake package is installed – contact the factory for details.  On locomotives, an air valve opens, applying independent braking and the throttle returns to idle.  In keeping with this philosophy - NO COMMAND, NO MOVEMENT - CATTRON-THEIMEG™ has designed your radio remote control system with the following safety and security features which may, at your request, be modified to meet specific operating requirements. CATTRON-THEIMEG™ engineers are always available to work with you to provide optimum operating system safety.  Safety & Security Features. Unique  address  code:  Each  controller  and  receiver/decoder  pair  is  configured  with  a unique  address  code  so  that  the  equipment  will  respond  only  to  the  controller  whose address code matches that of the decoder. Intelligent  digital  message  protocol:  CATTRON-THEIMEG™  remote  control  systems utilize  a  unique  message  protocol  for  industrial  control  applications  rather  than  the customary Electronic Data Processing (EDP) type of message format. Power ON/OFF switch: The controller has a power ON/OFF Key or Toggle Switch that must  be  set  to  ‘ON’  in  order  to  send  commands  to  the  receiver/decoder.  If  the  power ON/OFF  Switch  is  set  to  ‘OFF’,  the  decoder  will  remove  all  commands  from  the controlled machinery, stopping all movement.  However, the mainline control relay (OPR) may be maintained for up to 10 minutes, depending on system configuration. Operate relay (OPR): The operate (OPR) output relay shall be wired to control a user-provided  electro-magnetic  power  contactor.  The  electro-magnetic  contactor  opens  and closes the main electrical supply circuit(s) to the controlled device. Automatic Safety Override: The Automatic Safety Override (ASO) function continually monitors all selected decoder directional relay outputs.  If a directional relay closes without command from  the  controller, the  Operate (OPR) Relay immediately de-energizes. This prevents any movement of the controlled machine without command from the controller.
 Section 2, Page 2    ©03/2007, CATTRON-THEIMEG™ Safety & Security Features, continued. Data Error Checking:  All communications  from the controller to the receiver/decoder contain error-checking information (BCH data error detection routines).  The entire data command packet must pass error detection tests before being processed. Push-To-Operate (PTO) Bar: This  easily  activated  switch bar  must  be  released  when power is turned on, then pressed and held to enable the motion switch functions.  Releasing the PTO during normal operation causes the controller to send neutral commands to the receiver/decoder.  In certain cases the PTO will be programmed NOT to enable or disable a particular function switch, i.e. some locomotive braking functions.   Refer to the schematic drawing for your custom controller serial number to understand its configuration. NOTE:  Holding the PTO bar down when power is turned on places the controller in a technical diagnostic mode.  Refer to Maintenance Instructions (Section 4) for details. Optional ‘Keyless Entry Code’: This available feature requires an operator to activate a series of switches correctly before the controller power is turned on. Typical method of operation (incorporating above safety features). The Operate (OPR) relay is energized for the first time when: The  controller’s  Power  ON/OFF  Switch  is  set  to  ‘ON’  and  the  target  receiver/decoder  has  power applied.  With these conditions satisfied, a matching address code is sent by way of RF signal from the controller to the decoder. The OPR relay is wired to the mainline (ML) contactor on the crane. Once the mainline is energized, a continuously  repeated  valid  signal  must  be  received  for  function  outputs  to  engage.  If  this  signal  is interrupted for any reason, all function outputs will turn off unless programmed otherwise.  When operating within the USA, FCC rules state that RF transmitters in non-licensed controllers must switch off  within five seconds after the operator  releases a function button.   Consequently, the  OPR output is programmed to stay on for ten minutes after the last valid message is received.  During this time all Automatic Safety Override (ASO) monitored outputs must stay off or the ASO sensing in the decoder will interrupt this hold up time, de-energizing OPR. Figure 2-1  opposite  shows  an Operate (OPR) contact wired  directly to the mainline  (ML)  contactor. Setting the controller’s Power ON/OFF Switch to ‘ON’ will energize the mainline contactor. An auxiliary function may be used as a Reset (RST) output that will only be effective when the Operate (OPR) relay has been closed.  Momentary closure of the Reset (RST) relay picks up the mainline (ML) contactor, which  is maintained  under control of the  OPR.  Thus, power  is supplied to the controlled device.  If OPR opens, the mainline contactor releases, removing power from the controlled device and stopping all motion.
 ©03/2007, CATTRON-THEIMEG™     Section 2, Page 3 Typical method of operation (continued).  Figure 2-1.  Operate (OPR) contact wiring   Figure 2-2  below  shows  the Operate  (OPR) relay  and optional Reset  (RST)  relay  wired  to control  a mainline (ML) contactor. This configuration requires the operator to activate the reset function on the controller after he/she has turned the unit on.  Once reset, the ML contactor stays energized until OPR de-energizes.  In addition to being energized by the presence of a signal from the controller, OPR is under supervision of the Automatic Safety Override (ASO) circuit. The ASO circuit disables the OPR (shutting down the controlled machinery) if a directional output relay is active when no corresponding command is being received from the controller.  In this event, no action is required by the operator to stop the equipment. The  ASO  safety  circuitry  will  stop  motion  automatically  without  any  operator  command  when  a directional output relay fault is detected. Figure 2-2.  Operate (OPR) contactor and Reset Relay (RST) wiring  120VL1 MLMLMANUALDISCONNECTL2L3 LL1LL2LL3 TOMOTORRECEIVER/DECODEREXISTING CONTROLS OPRRC5.0AOPR120VRSTRRCC5.0A5.0AL1 MLML MLMANUALDISCONNECTL2L3 LL1LL2LL3 TOMOTORRECEIVER/DECODEREXISTING CONTROLS
 Section 2, Page 4    ©03/2007, CATTRON-THEIMEG™ Radio Control Operator’s Duties – General Equipment.      WARNINGS: WITH  THE  EXCEPTION  OF  LOCOMOTIVES,  ALL  EQUIPMENT  MUST HAVE  A  MAINLINE  (ML)  CONTACTOR  INSTALLED  AND  ALL TRACKED EQUIPMENT (i.e. CRANES) HAVE A BRAKE INSTALLED. THE  REMOTE  CONTROL  OPERATE  (OPR)  RELAY  MUST  BE CONNECTED  TO  THE  MAINLINE  SO  THAT  STOP  COMMANDS  OR FAULT  CONDITIONS  MONITORED  BY  AUTOMATIC  SAFETY OVERRIDE  (ASO)  CIRCUITRY  WILL  DE-ENERGIZE  THE  MAINLINE CONTACTOR AND SET THE EQUIPMENT BRAKE.  FAILURE TO COMPLY WITH THE ABOVE WARNINGS MAY RESULT IN SERIOUS  INJURY  OR  DEATH  TO  PERSONNEL  AND  DAMAGE  TO EQUIPMENT.       WARNING: MORE  THAN  ONE  REMOTE  CONTROL  SYSTEM  MAY  BE  USED  AT, AROUND,  OR  NEARBY  YOUR  OPERATING  FACILITY.    THEREFORE, YOU MUST INSURE THE ADDRESS CODE AND FREQUENCY OF YOUR PADDLE CONTROLLER EXACTLY MATCHES THE ADDRESS CODE AND FREQUENCY OF THE DESIRED EQUIPMENT TO BE OPERATED. FAILURE TO COMPLY WITH THE ABOVE WARNING MAY RESULT IN THE  UNDESIRED  OPERATION  OF  OTHER  EQUIPMENT  WHICH,  IN TURN,  COULD  RESULT  IN  SERIOUS  INJURY  OR  DEATH  TO PERSONNEL AND DAMAGE TO EQUIPMENT.       WARNING: ON CAB AND REMOTE OPERATED CRANES OR CARRIERS AN AUDIBLE OR  VISUAL  WARNING  MEANS  SHALL  BE  PROVIDED.    IN  ADDITION, ALL  EQUIPMENT  SHALL  HAVE  AUDIO  OR  VISUAL  ALARM INDICATIONS  MEETING  GOVERNMENTAL  REQUIREMENTS.  FAILURE TO IMPLEMENT THIS WARNING MAY RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.
 ©03/2007, CATTRON-THEIMEG™     Section 2, Page 5 Radio Control Operator’s Duties – General Equipment, continued.     WARNING: DUE  TO  FCC  PART  15  AND  DOC  RSS-210  RADIO  TRANSMIT REGULATIONS,  THE  OPR  OUTPUT  TO  WHICH  YOUR  CONTROLLED EQUIPMENT’S  MAINLINE  CONTACTOR  IS  CONNECTED  WILL  REMAIN ENERGIZED  FOR  TEN  MINUTES AFTER  THE  CONTROLLER  POWER  IS SET  TO  ‘OFF’,  OR  FOR  TEN  MINUTES  AFTER  THE  LAST  TIME  A FUNCTION  SWITCH  IS  ACTIVATED.    CONSEQUENTLY,  SPECIAL  CARE MUST BE TAKEN IF THE CRANE OR TRACKED MACHINE IS EQUIPPED WITH  A  PARKING  BRAKE  THAT  IS  CONFIGURED  TO  ENGAGE  WHEN THE MAINLINE CONTACTOR DE-ENERGIZES.    TO PREVENT A POTENTIALLY HAZARDOUS SITUATION, YOU SHOULD IMMEDIATELY SELECT THE RED ‘STOP’ FUNCTION ON YOUR REMOTE CONTROLLER  AFTER  COMPLETION  OF  OPERATIONS.    SUCH  ACTION WILL INSURE THE PARKING BRAKE (IF EQUIPPED AND CONFIGURED AS ABOVE) IS SET, PREVENTING UNINTENTIONAL MOVEMENT OF THE CRANE OR TRACKED MACHINE. FAILURE TO COMPLY WITH THIS WARNING MAY RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.      WARNING: NEVER DISABLE THE PUSH TO OPERATE (PTO) BAR SWITCH ON YOUR REMOTE CONTROLLER.  FAILURE TO COMPLY WITH THIS WARNING MAY  RESULT  IN  DAMAGE  TO  EQUIPMENT,  SERIOUS  INJURY,  OR DEATH.      Important Safety Note: When  using  the  controller,  operators are  instructed  to  wear  a factory  approved carrying harness with the controller attached at all times.  If a controller must be left  unattended,  the  STOP  switch  (when  installed  to  the  controller)  should  be depressed and the controller’s power ON/OFF switch set to ‘OFF’.  If the power ON/OFF  switch  is  a  key  switch,  the  key  should  also  be  removed  to  prevent unauthorized use of the controller.
 Section 2, Page 6    ©03/2007, CATTRON-THEIMEG™ Radio Control Operator’s Duties – General Equipment, continued. The  following  procedures  provide  general  guidelines  for  radio  control  operation  of  equipment  and should not be used as a substitute for your plant operating procedures. 1. Before operating equipment, carry out the following: a. Insure  the  address  code  and  frequency  of  your  paddle  controller  exactly  matches  the address code and frequency of the target equipment to be operated.   The address and frequency assigned to your controller is recorded (1) on the front page of this  manual,  and  (2)  on  a  serial  tag  located  inside  the  battery  door.  The  address  and frequency of the target receiver/decoder is recorded (1) on the front page of the manual supplied with the portable remote control system, and (2) on a label located inside the receiver/decoder.   If  a  controller  having  the  wrong  address  code  and  frequency  is  selected,  the  target equipment will not operate.  However, other equipment located at, around, or nearby your facility may become operational. NOTES:  If you are not familiar with the controls and indicators on your controller,  please refer to ‘Controls and Indicators’ in Section 3 of this manual and the operational description provided with your controller.   Some controllers have two power ON/OFF switches (a Keyswitch and a Toggle switch).  Both of these switches must be set to ‘ON’ for power to be applied to the controller. b. Set the controller’s Power ON/OFF Switch(es) to the ‘ON’ position. When transmitting with  a  good  battery,  two  short  ‘beeps’  will  be  heard  immediately  after  the  Power ON/OFF Switch is set to ‘ON’ and a green TRANSMIT LED will ‘flash’ rhythmically.  When the battery starts to go low, the green LED changes to  a red  LOW BATTERY LED  which  ‘flashes’  continuously.    This  means  you  should  change  or  re-charge  the battery pack as soon as possible - refer to Battery Packs and Battery Pack Charging in Section 3 of this manual.  c. When installed, depress the ALARM/RESET push button switch located in the center of the PTO bar (this is normally an optional function that sounds the equipment alarm or horn and resets the main power contactor). d. Check each function independently to be sure that equipment is responding correctly. e. Where a limit switch is provided, you should check the limit switch at the beginning of each shift as defined by your plant operating procedures. f. Check Range Limiting if used – refer to Appendix ‘A’ of the manual supplied with your PRC system. g. Check STOP operation h. Check brake operation.
 ©03/2007, CATTRON-THEIMEG™     Section 2, Page 7 Radio Control Operator’s Duties – General Equipment, continued. 2. You must report all defective or missing safety equipment, mechanical or electrical defects to your supervisor without delay.  Do not continue operation until fully repaired. 3. If anyone is in the path of equipment travel, stop and sound the alarm before proceeding.  Do not   proceed until the pathway is clear 4.  Persons operating this equipment shall not use a limit stop as a utility stopping device. 5.  When leaving the equipment area for any reason, set the controller’s Power ON/OFF Switch(es) to the ‘OFF’ position.  If a Key Switch is installed, remove the key from the controller and keep it on your person. 6.  Do not allow any unauthorized person to operate the controller. 7.  Do not operate the controller at a distance where the equipment and all surrounding objects are not visible. 8.  Do not attempt to override any of the safety features built into the Radio Control System. 9. If, for any reason, you or anyone has to board the radio controlled equipment, set the controller’s Power ON/OFF Switch(es) to the ‘OFF’ position.  If a Key Switch is installed, remove the key from the controller and keep it on your person.
 Section 2, Page 8    ©03/2007, CATTRON-THEIMEG™ Radio Control Operator’s Duties – Electrical Overhead Traveling (EOT) Crane.      WARNINGS: ALL  EQUIPMENT  MUST  HAVE  A  MAINLINE  (ML)  CONTACTOR INSTALLED  AND  ALL  TRACKED  EQUIPMENT  (i.e.  CRANES)  HAVE  A BRAKE INSTALLED. THE  REMOTE  CONTROL  OPERATE  (OPR)  RELAY  MUST  BE CONNECTED  TO  THE  MAINLINE  SO  THAT  STOP  COMMANDS  OR FAULT CONDITIONS MONITORED BY AUTOMATIC SAFETY OVERRIDE (ASO)  CIRCUITRY  WILL  DE-ENERGIZE  THE  MAINLINE  CONTACTOR AND SET THE EQUIPMENT BRAKE.  FAILURE TO COMPLY WITH THE ABOVE WARNINGS MAY RESULT IN SERIOUS  INJURY  OR  DEATH  TO  PERSONNEL  AND  DAMAGE  TO EQUIPMENT.       WARNING: MORE  THAN  ONE  REMOTE  CONTROL  SYSTEM  MAY  BE  USED  AT, AROUND,  OR  NEARBY  YOUR  OPERATING  FACILITY.    THEREFORE, YOU  MUST  INSURE  THE  ADDRESS CODE  AND FREQUENCY  OF  YOUR PADDLE CONTROLLER EXACTLY MATCHES THE ADDRESS CODE AND FREQUENCY OF THE DESIRED EQUIPMENT TO BE OPERATED. FAILURE TO COMPLY WITH THE ABOVE WARNING MAY RESULT IN THE  UNDESIRED  OPERATION  OF  OTHER  EQUIPMENT  WHICH,  IN TURN, COULD RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.       WARNING: ON CAB AND REMOTE OPERATED CRANES OR CARRIERS AN AUDIBLE OR VISUAL WARNING MEANS SHALL BE PROVIDED.  IN ADDITION, ALL EQUIPMENT  SHALL  HAVE  AUDIO  OR  VISUAL  ALARM  INDICATIONS MEETING  GOVERNMENTAL  REQUIREMENTS.    FAILURE  TO IMPLEMENT  THIS  WARNING  MAY  RESULT  IN  SERIOUS  INJURY  OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.
 ©03/2007, CATTRON-THEIMEG™     Section 2, Page 9 Radio Control Operator’s Duties – EOT Crane, continued.     WARNING: DUE  TO  FCC  PART  15  AND  DOC  RSS-210  RADIO  TRANSMIT REGULATIONS,  THE  OPR  OUTPUT  TO  WHICH  YOUR  CONTROLLED EQUIPMENT’S MAINLINE CONTACTOR IS CONNECTED WILL REMAIN ENERGIZED FOR TEN MINUTES AFTER THE CONTROLLER POWER IS SET  TO  ‘OFF’,  OR  FOR  TEN  MINUTES  AFTER  THE  LAST  TIME  A FUNCTION SWITCH IS ACTIVATED.  CONSEQUENTLY, SPECIAL CARE MUST BE TAKEN IF THE CRANE OR TRACKED MACHINE IS EQUIPPED WITH A PARKING BRAKE THAT IS CONFIGURED TO ENGAGE WHEN THE MAINLINE CONTACTOR DE-ENERGIZES.    TO PREVENT A POTENTIALLY HAZARDOUS SITUATION, YOU SHOULD IMMEDIATELY  SELECT  THE  RED  ‘STOP’  FUNCTION  ON  YOUR REMOTE CONTROLLER AFTER COMPLETION OF OPERATIONS.  SUCH ACTION  WILL  INSURE  THE  PARKING  BRAKE  (IF  EQUIPPED  AND CONFIGURED  AS  ABOVE)  IS  SET,  PREVENTING  UNINTENTIONAL MOVEMENT OF THE CRANE OR TRACKED MACHINE. FAILURE TO COMPLY WITH THIS WARNING MAY RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.       WARNING: NEVER DISABLE THE PUSH TO OPERATE (PTO) BAR SWITCH ON YOUR REMOTE CONTROLLER.  FAILURE TO COMPLY WITH THIS WARNING MAY  RESULT  IN  DAMAGE  TO  EQUIPMENT,  SERIOUS  INJURY,  OR DEATH.      Important Safety Note: When  using  the  controller,  operators are  instructed  to  wear  a factory  approved carrying harness with the controller attached at all times.  If a controller must be left  unattended,  the  STOP  switch  (when  installed  to  the  controller)  should  be depressed and the controller’s power ON/OFF switch set to ‘OFF’.  If the power ON/OFF  switch  is  a  key  switch,  the  key  should  also  be  removed  to  prevent unauthorized use of the controller.
 Section 2, Page 10    ©03/2007, CATTRON-THEIMEG™ Radio Control Operator’s Duties – EOT Crane, continued. The following procedures provide general guidelines for radio control operation of an EOT crane and should not be used as a substitute for your plant operating procedures.  Please note that a complete set of Recommended Safety Rules for Cranes is provided at the end of this manual.  1.        Before lifting any loads, carry out the following: a. Insure  the  address  code  and  frequency  of  your  paddle  controller  exactly  matches  the address code and frequency of the target equipment to be operated.   The address and frequency assigned to your controller is recorded (1) on the front page of this  manual, and  (2) on  a  serial tag located inside  the  battery  door.    The  address  and frequency of the target receiver/decoder is recorded (1) on the front page of the manual supplied with the portable remote control system, and (2) on a label located inside the receiver/decoder.   If  a  controller  having  the  wrong  address  code  and  frequency  is  selected,  the  target equipment will not operate.  However, other equipment located at, around, or nearby your facility may become operational. NOTES:  If  you  are  not  familiar  with  the  controls  and  indicators  on  your  controller,  please refer  to  ‘Controls  and  Indicators’ in  Section  3  of  this  manual and the operational description provided with your controller.   Some controllers have two power ON/OFF switches (a Keyswitch and a Toggle switch).  Both of these switches must be set to ‘ON’ for power to be applied to the controller. b. Set the controller’s Power ON/OFF Switch(es) to the ‘ON’ position.  When transmitting with  a  good  battery,  two  short  ‘beeps’  will  be  heard  immediately  after  the  Power ON/OFF Switch is set to ‘ON’ and a green TRANSMIT LED will ‘flash’ rhythmically.  When the battery starts to go low, the green LED changes to  a red  LOW BATTERY LED  which  ‘flashes’  continuously.    This  means  you  should  change  or  re-charge  the battery pack as soon as possible - refer to Battery Packs and Battery Pack Charging in Section 3 of this manual. c. When installed, depress the ALARM/RESET push button switch located in the center of the PTO bar (this is normally an optional function that sounds the equipment alarm and resets the main power contactor). d.  Where a limit switch is provided, you should check the limit switch at the beginning of each shift as defined by your plant operating procedures. e.  Check each function independently to be sure that equipment is responding correctly. f. Check range limiting if used – refer to Appendix ‘A’ of the manual supplied with your PRC system. g. Check STOP operation. h. Check Brake operation.
 ©03/2007, CATTRON-THEIMEG™     Section 2, Page 11 Radio Control Operator’s Duties – EOT Crane, continued.   2.  You must report all defective or missing safety equipment, mechanical or electrical defects to your supervisor without delay.  Do not continue operation until fully repaired.   3.  When raising or lowering a load, proceed slowly and make certain the load is under control.   4.  When lifting maximum load, you should test the brakes by raising the load a few inches from the floor.  If the brakes will not hold, the load shall be immediately lowered and not moved until brakes are adjusted or repaired.   5.  Center the Trolley directly over the load before starting to hoist.   6.  Take slack out of  chains or slings gradually  and make sure hands  and other objects  are clear before making the lift.   7.  Keep all parts of the body away from the lifts.  Also, do not stand under a lift. 8. Do not make a lift or move the equipment if anyone is in a position to be injured. 9. Load should not be carried over workmen's heads. 10.  If anyone is in the path of travel, stop and sound the alarm before proceeding. Do not continue until the pathway is clear.  11.  Do not drag slings, chains, etc. along the floor. 12.  Persons operating this equipment shall not use a limit stop as a utility stopping device. 13.  Bumping other cranes or run-away stops is prohibited. 14.  When moving the equipment to the loading point, be sure that hook block, attachment, or cables will not fall on the adjacent equipment. 15.  When  leaving  the  crane  area  for  any  reason,  be  sure  slings  or  chains  are  raised  and  set  the controller’s  Power  ON/OFF  Switch(es)  to  the  ‘OFF’  position.    If  a  Key  Switch  is  installed, remove the key from the controller and keep it on your person. 16.  Do not allow any unauthorized person to operate the controller. 17.  Do not operate the controller at a distance where the crane and all surrounding objects are not visible. 18.  Do not attempt to override any of the safety features built into the Radio Control System. 19. If, for any reason, you or anyone has to board a radio controlled crane, set the controller’s Power ON/OFF Switch(es) to the ‘OFF’ position.  If a Key Switch is installed, remove the key from the controller and keep it on your person.
 Section 2, Page 12    ©03/2007, CATTRON-THEIMEG™ Radio Control Operator's Duties - Locomotive.      WARNINGS: ALL  TRACKED  EQUIPMENT  (i.e.  LOCOMOTIVES)  MUST  HAVE  A BRAKE INSTALLED. THE  REMOTE  CONTROL  OPERATE  (OPR)  RELAY  MUST  BE CONFIGURED  SO  THAT  STOP  COMMANDS  OR  FAULT  CONDITIONS MONITORED  BY  AUTOMATIC  SAFETY  OVERRIDE  (ASO)  CIRCUITRY WILL SET THE THROTTLE TO IDLE, DISCONNECT THE GENERATOR FIELD, AND SET THE INDEPENDENT BRAKE.  FAILURE TO COMPLY WITH THE ABOVE WARNINGS MAY RESULT IN SERIOUS  INJURY  OR  DEATH  TO  PERSONNEL  AND  DAMAGE  TO EQUIPMENT.       WARNING: MORE  THAN  ONE  REMOTE  CONTROL  SYSTEM  MAY  BE  USED  AT, AROUND,  OR  NEARBY  YOUR  OPERATING  FACILITY.    THEREFORE, YOU MUST INSURE THE ADDRESS CODE AND FREQUENCY OF YOUR PADDLE CONTROLLER EXACTLY MATCHES THE ADDRESS CODE AND FREQUENCY OF THE DESIRED EQUIPMENT TO BE OPERATED. FAILURE TO COMPLY WITH THE ABOVE WARNING MAY RESULT IN THE  UNDESIRED  OPERATION  OF  OTHER  EQUIPMENT  WHICH,  IN TURN,  COULD  RESULT  IN  SERIOUS  INJURY  OR  DEATH  TO PERSONNEL AND DAMAGE TO EQUIPMENT.       WARNING: ON  CAB  AND  REMOTE  OPERATED  LOCOMOTIVES  OR  CARRIERS  AN AUDIBLE  OR  VISUAL  WARNING  MEANS  SHALL  BE  PROVIDED.    IN ADDITION, ALL EQUIPMENT SHALL HAVE AUDIO OR VISUAL ALARM INDICATIONS MEETING GOVERNMENTAL REQUIREMENTS.  FAILURE TO IMPLEMENT THIS WARNING MAY RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.     WARNING: NEVER DISABLE THE PUSH TO OPERATE (PTO) BAR SWITCH ON YOUR REMOTE CONTROLLER.  FAILURE TO COMPLY WITH THIS WARNING MAY  RESULT  IN  DAMAGE  TO  EQUIPMENT,  SERIOUS  INJURY,  OR DEATH.
 ©03/2007, CATTRON-THEIMEG™     Section 2, Page 13 Radio Control Operator's Duties - Locomotive, continued.    Important Safety Note: When  using  the  controller,  operators are  instructed  to  wear  a factory  approved carrying harness with the controller attached at all times.  If a controller must be left  unattended,  the  STOP  switch  (when  installed  to  the  controller)  should  be depressed and the controller’s power ON/OFF switch set to ‘OFF’.  If the power ON/OFF  switch  is  a  key  switch,  the  key  should  also  be  removed  to  prevent unauthorized use of the controller.  The following procedures provide  general  guidelines for radio control operation of  a locomotive  and should not be used as a substitute for your plant operating procedures.  Please note that a complete set of Recommended Safety Rules for Locomotives is provided at the end of this manual.   1.  Perform all locomotive pre-departure tests according to the locomotive manufacturer's operation manual.    Do  not  proceed  unless  the  locomotive  is  operating  satisfactorily  according  to  the manufacturer's instructions. 2.  Before departure, carry out the following: a.  Insure  the  address  code  and  frequency  of  your  paddle  controller  exactly  matches  the address code and frequency of the target equipment to be operated.   The address and frequency assigned to your controller is recorded (1) on the front page of this  manual, and  (2) on  a  serial tag located inside  the  battery  door.    The  address  and frequency of the target receiver/decoder is recorded (1) on the front page of the manual supplied with the portable remote control system, and (2) on a label located inside the receiver/decoder.  If  a  controller  having  the  wrong  address  code  and  frequency  is  selected,  the  target equipment will not operate.  However, other equipment located at, around, or nearby your facility may become operational. NOTES:  If you are not familiar with the controls and indicators on your  controller,  please refer to ‘Controls and Indicators’ in Section 3 of this manual and the operational description provided with your controller.   Some controllers have two power ON/OFF switches (a Keyswitch and a Toggle switch).  Both of these switches must be set to ‘ON’ for power to be applied to the controller. b.  Set the controller’s Power ON/OFF Switch(es) to the ‘ON’ position.  When transmitting with  a  good  battery,  two  short  ‘beeps’  will  be  heard  immediately  after  the  Power ON/OFF Switch is set to ‘ON’ and a green TRANSMIT LED will ‘flash’ rhythmically.  When the battery starts to go low, the green LED changes to  a red  LOW BATTERY LED  which  ‘flashes’  continuously.    This  means  you  should  change  or  re-charge  the battery pack as soon as possible - refer to Battery Packs and Battery Pack Charging in Section 3 of this manual.
 Section 2, Page 14    ©03/2007, CATTRON-THEIMEG™ Radio Control Operator's Duties - Locomotive, continued.  c.  Depress the  HORN switch on  the controller.  The  horn should sound on the target locomotive. d. Check  each  brake  function  independently  to  be  sure  the  locomotive  is  responding correctly  to  all  brake  applications,  including  emergency  stop  and  release  commands.  Observe  gages  in  the  cab  for  proper  readings  and  verify  that  the  brake  cylinders  are moving properly.  e.  Test train brakes (if equipped). f.  Check all auxiliary equipment, such as bell, headlight, sanders, uncouple, etc.   3.  You must report all defective or missing safety equipment, mechanical or electrical defects to your supervisor without delay.  Do not continue operation until fully repaired.    4.  When ready to move the locomotive for the first time, proceed slowly and make certain the load is under control.     5.  Take the slack out of the couplers gradually and  make sure hands and other objects are clear before making command.   6.  Keep  all  parts  of  the  body  away  from  the  rolling  equipment  and  never walk  on  the  tracks ahead of the train.    7.  Do not move the locomotive if anyone is in a position to be injured.   8.  If anyone is in the path of travel, stop and sound the horn.  Do not proceed until the tracks are clear.   9.  Heavy bumping of cars or stops is prohibited. 10.  When leaving the locomotive for any reason, be sure the locomotive throttle is set to ‘IDLE’ and the  brakes  are  fully  applied.      Set  the  controller’s  Power  ON/OFF  Switch(es)  to  the  ‘OFF’ position.  If a Key Switch is installed, remove the key from the controller and keep it on your person. 11.  Do not allow any unauthorized person to operate the controller. 12.  Do  not  operate  the  controller  at  a  distance  where  the  locomotive,  railcars,  rail-track,  and  all surrounding objects are not visible. 13.  Do not attempt to override any of the safety features built into the Radio Control System. 14. If, for  any reason,  you  or anyone has  to board a  radio controlled  locomotive or train,  set the controller’s  Power  ON/OFF  Switch(es)  to  the  ‘OFF’  position.  If  a  Key  Switch  is  installed, remove the key from the controller and keep it on your person.    END OF SECTION
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 1 Section 3 – Operating Instructions  Controls and Indicators. Each paddle controller has been designed and  custom built  for a  specific remote control application, therefore its operation will differ from model to model.   For this reason, it is not possible to describe an individual controller’s switch and indicator configuration in this manual – there are too many variations.  However, all paddle controllers incorporate some or all of the controls and indicators identified in Figure 3-1 below.  For your controller’s exact switch and indicator configuration, please refer to the schematic drawing provided with your paddle controller.  Figure 3-1.  Paddle Controller – controls, indicators and features PTO BARSWITCHSTRAP/HARNESSANCHORBRACKET POWER ON/OFFTOGGLE SWITCHPOWER ON/OFFKEY SWITCH‘FLAG’ STYLELEVER PADDLE‘LOW BATTERY’ & ‘TRANSMIT’ LEDMOMENTARYPUSH BUTTONSWITCH PUSH BUTTONSWITCH ‘TALKBACK’ LEDINDICATOR PANELLEVER PODTOGGLESWITCH
 Section 3, Page 2    ©03/2007, CATTRON-THEIMEG™ Controls and Indicators, continued. POWER ON/OFF KEY SWITCH – This key switch prevents unauthorized personnel from operating the control system.   When the key switch is set to ‘ON’, internal battery power is applied to an RF encoder/transmitter  within  the  controller  and  the  operator  can  control  all  auxiliary  (non-motion) functions  without  pressing  the  PUSH-TO-OPERATE  (PTO)  bar.    The  power  ON/OFF  key  switch controls a mainline  magnetic contactor on the machine.  This in turn controls the main power to the machine motors.  When the controller is not in use, the key may be withdrawn from its switch location and kept  on the operator’s  person.    Note that: (1) a front panel mounted,  maintained 2-position toggle switch may be substituted for this side mounted key switch, and (2) some controllers may have both types of these power ON/OFF switches installed. POWER ON/OFF TOGGLE SWITCH – When this switch is set to ‘ON’, internal battery power is applied  to  an  RF  encoder/transmitter  within  the  controller  and  the  operator  can  control  all  auxiliary (non-motion) functions without pressing the PUSH-TO-OPERATE (PTO) bar.  The power ON/OFF key switch controls a mainline magnetic contactor on the machine.  This in turn controls the main power to the  machine  motors.    Note  that:  (1)  on  some  controllers,  a  side  mounted,  key  switch  may  be substituted for this front panel mounted toggle switch, and (2) some controllers may have both types of these power ON/OFF switches installed. PUSH-TO-OPERATE (PTO) BAR  - This bar is a large, full length, spring-return switch located on top  of  the  unit  that  is  generally  used  as  a  safety  device  that  electronically  disconnects  all  motion switches when  it is released, thus stopping motion commands from these switches.   The  PTO bar is easily and naturally activated by a convenient and comfortable part of the operator's hand and must be depressed and maintained before and when any motor or motion command is initiated.   It should be noted that operation of the PTO bar is not required for auxiliary functions, i.e. magnet, lights, etc.  For the  exact  configuration  of  the  PTO  Bar,  refer  to  the  custom  drawing  package  supplied  with  your controller.  LEVER POD(S) – Up to six lever pods can be installed to your paddle controller and you should refer to  the  custom  drawing  package  supplied  with  your  controller  for  the  specific  configuration.      These switches may be 11-position, spring return-to-center switches, stepless levers, or dual axis joysticks.  For cranes with stepped output there are five forward (or down) positions, five reverse (or up) positions, and a center ‘OFF’ (or neutral) position.  Each of the five positions, in either direction, selects a different motor speed.  The motor speed increases as the switches are moved away from the center position in each direction.  The crane motors may have fewer than five speeds.  For example, cranes with two speed motors where the third, fourth, and fifth position of the switches operate the motors at the highest speed which is speed two.  As viewed from the operator's position, the crane motor control levers are normally labeled from left to right; BRIDGE, TROLLEY, and HOIST.  If used with a four-motor crane system, an AUX HOIST control lever is located on the extreme right of the unit.  Locomotive controller lever positions are laid out according to the user’s requirements and you should refer to the custom drawing package supplied with your controller.  Normal locomotive configuration as viewed  left  to  right  from  the  operator’s  position  is:  THROTTLE,  DIRECTION,  INDEPENDENT BRAKE and TRAIN BRAKE.
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 3 Controls and Indicators, continued. In addition to the ‘Flag’ style lever paddle (illustrated), different style levers and knobs are available – refer to ‘Accessories’ in Section 5 of this manual for details.  Finally, some controllers are built with a special two-axis joystick configuration - refer to special operation descriptions and the custom drawing package supplied with your controller for specific information. SWITCHES – A momentary push button switch is mounted in the center of the PTO bar, and up to six switches can be located in front of the PTO bar.  Two additional switches may be located below the lever pods when two finger application is required to prevent the accidental operation of safety critical functions  such  as  ‘MAGNET’  ‘GRAB’,  and  ‘VACUUM’.    Depending  upon  the  control  application, your controller may be configured with some or all of the following switch types: • Rotary selector or key switch – mainly used for address selection • Maintained 2-position toggle – mainly used for auxiliary ‘ON/OFF’ functions (lights, application of sand, and power up) • Momentary pushbutton, or toggle – mainly used for non motion functions (horn, brake, alarm/reset, magnet lift, magnet drop) TRANSMIT & LOW BATTERY LED  – This  LED is  part of  the battery  management system and flashes  green  when  the  controller’s  Power  ON/OFF  Switch  is  set  to  ‘ON’  and  the  controller  is transmitting with a good battery installed.  The LED flashes red when the battery is low and sounds a beeper to alert the operator. In addition, a low battery cut-off circuit stops the controller micro-processor when voltage goes below safe operating range.  This is because RF transmitters always operate at full power over the entire life of the battery. ‘TALKBACK™’ LED INDICATOR PANEL – This feature adds two-way data communication to the CATTRON-THEIMEG™  Portable  Radio  Remote  Control  (PRRC)  System  when  used  in  conjunction with the MP96 Series Receiver/Decoder.  In the standard PRRC System, all data communication is a type of one-way communication: namely, control information sent from the operator’s controller to the receiver/decoder.    With  TALKBACK  the  decoder  can  communicate  back  to  the  controller.    Up  to sixteen ON/OFF bits of information can be sent back from the MP96 decoder to the paddle controller.  These bits originate in the MP96 decoder and can be either External Event Inputs or ASO Inputs.  The received bits are displayed on the controller using up to twelve light emitting diodes and/or a Liquid Crystal Display (LCD).  The decoder will make a TALKBACK transmission to the controller about once every second.  Since the encoder and decoder are both making transmissions on the same frequency, more airtime is used.  In this instance, timesharing multiple controllers on a single radio channel is not recommended.   Also, the controller’s battery life will  be  reduced, sometimes significantly, depending on  the  type of indicating devices used (digital displays, LED's, etc.).  For example, a controller operating on 450 MHz with a  Ni-Cad battery pack will last 10 to  14 hours  of continuous  operation instead of 36 hours.   It should be noted that Alkaline battery packs are not usable with TALKBACK systems.
 Section 3, Page 4    ©03/2007, CATTRON-THEIMEG™ Controls and Indicators, continued. Your customized controller and PRRC system drawings will show the exact operation of your control unit.  A typical example of TALKBACK would be its use on radio controlled locomotives.   On a locomotive there is usually a ‘Tree’ of four or five lights used as status indicators that is mounted on each  side of the  locomotive.  These lights usually show  the operator the  status  of ‘FORWARD’, ‘REVERSE’, ‘THROTTLE’, ‘BRAKES’, and Remote Control System ‘ON’.  Consequently, the PRRC operator must always be close enough to the locomotive to see these lights in order  to  determine  the  status.    However,  with  the  TALKBACK  option,  status  indications  are transmitted back to the controller and displayed with LED's.   This enables the PRRC operator to assume a commanding view of the whole train and its operating area rather than just the locomotive.  Other fault indications can also be displayed.  Examples are: Engine Alarm, Low Air Pressure, High Engine  Water  Temperature,  Low  Engine  Oil  Pressure,  Wheels  Slipping,  STOP  Switch  Active,  and Speedometer Digital Readout. In  the  case  of  an  overhead  crane,  the  TALKBACK  option  enables  status  and  external  event information to be viewed on the controller.  Because the PRRC operator is not required to climb the crane,  or  view  the  lights  mounted  on  the  crane  to  determine  status,  he  or  she  is  able  to  assume  a commanding view of the entire crane operating area.   Some typical display indications for cranes are: Magnet Power ON, Magnet Lift ON, Operator ID Lights (pitch & catch), Mainline ON, Low Brake Pressure, Direction Verification, Out of Range (with Range Limiter), ASO Fault, Latched/Unlatched, Aligned (Zone), Hoist Limit Switch, Thermal Trip, and Under Voltage Trips.
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 5 General Operating Procedure.   NOTES:  When using the controller, operators are instructed to wear a factory approved carrying harness with the controller attached at all times.     If a controller must be left unattended, the STOP Switch (when installed to the controller) should be depressed and the controller’s POWER ON/OFF switch set to ‘OFF’.  If the POWER ON/OFF switch is a key switch, the key should also be removed to prevent unauthorized use of the controller (refer to Section 2, Page 7, Item 5 of this manual).   Using a Carrying Harness to support the controller will greatly enhance operator comfort and operational safety.  Two harnesses are available, as illustrated below in Figures 3-2 and 3-3.  Refer to these illustrations for details and CATTRON-THEIMEG™ Part Numbers.  Figure 3-2. Standard carrying harness Standard Carrying Harnesses are available in 2 sizes as follows:   CLN-6096                     Small to Large                       37.5 - 56 inches   CLN-6096XL                Extra Large                             48 - 68 inches
 Section 3, Page 6    ©03/2007, CATTRON-THEIMEG™  General Operating Procedure, continued.    Figure 3-3. – ‘Low back’ support carrying harness  1.  Referring to Figure 3-4 below, assemble and put on the carrying harness, attach the controller to the harness and adjust for comfortable operation.  Middle Stay Strap AdjusterCarrying StrapAnchor CatchesPress StudsShoulder HarnessREAR VIEWHarness AdjusterRight Hand Side PullLeft Hand Side PullLower Back andAbdominal SupportLow Back Support Carrying Harnesses are available as follows:The Lower Back and Abdominal Support is a lightweight and comfortable device thatacts as a reminder to lift properly.  The Side Pulls give you the extra support neededwhen lifting.   When on break or lunch, you may want to loosen the side pulls, butD O  N OT   forg e t  t o  re- fas ten   the m   w h e n  r e tu rn i n g  t o   work.CLN-300902S                 Small                                      32 - 36 inchesCLN-300903M                Medium                                  36 - 40 inchesCLN-300904L                 Large                                      40 - 44 inchesCLN-300905XL              Extra Large                            44 - 48 inchesCLN-300906XXL           Double Extra Large               48 - 52 inchesCLN-300907XXXL        Triple Extra Large                 52 - 56 inchesCLN-300901XS              Extra Small                             28 - 32 inchesNOTE:  IF YOU HAVE OR HAVE HAD AN INJURY, CONSULT        YOUR DOCTOR BEFORE USING THIS PRODUCT.
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 7 General Operating Procedure, continued.   Figure 3-4. Carrying harnesses, assembly and fitting 1-1.  Place the Low Back Support around  the         body just below the navel, ensuring         the Middle Stay (see Fig 3-3 above)         locates  in the center of the low back.         Stretch the right end across  the left         and attach firmly.1-2.  Loosen elasticized Side Pulls and        stretch forward as far as possible.        Position the left hand side pull over        the right hand side pull and attach        firmly but comfortably.1-3.   Using Adjuster, lengthen or shorten         Carrying Strap as necessary to provide         a snug fit.  Fasten Carrying Strap         around waist using Press Studs.1-4.   Cross the Shoulder Harness Straps at the back          and bring each strap to the front.         Adjust the length of the shoulder straps as          required.  Fasten the end catches of the shoulder         straps into the buckles of the Upper Anchor          Catches located on the Carrying Strap 1-5.   Fasten the Controller to the Harness          using the four Anchor Catches located          on the Carrying Strap.    Re-adjust the          harness as necessary for individual          comfort and preference.        LOW BACK SUPPORTCARRYING HARNESS ONLYSTANDARD AND LOW BACK SUPPORTCARRYING HARNESSESSTANDARD AND LOW BACK SUPPORTCARRYING HARNESSESSTANDARD AND LOW BACK SUPPORTCARRYING HARNESSESLOW BACK SUPPORTCARRYING HARNESS ONLY
 Section 3, Page 8    ©03/2007, CATTRON-THEIMEG™ General Operating Procedure, continued.   NOTES:   Holding the PTO bar down when power is turned on places the controller in a technical diagnostic mode - refer to Maintenance Instructions (Section 4) for details.  The PTO bar must be up when starting the controller or the system will not operate.    On some controllers, the side mounted Power ON/OFF Key Switch may be replaced with a front panel mounted, 2-position maintained toggle switch. Alternatively, some controllers may have both types of these power ON/OFF switches installed. 2.  Set the controller’s Power ON/OFF Switch(es) to ‘ON’.   Observe that the TRANSMIT/LOW BATTERY LED momentarily flashes yellow and two quick ‘beeps’ are heard. If the LED is red, replace or recharge the battery pack – refer to Battery Packs and Battery Pack Charging at the end of this section. When transmitting with a good battery pack, the green TRANSMIT LED should ‘flash’ rhythmically. 3.  When your controller is equipped with the optional ‘Keyless Entry Code’ feature, an assigned sequence  of  function  switches  must  be  operated  within  10  seconds  after  the  Power  ON/OFF Switch is set to ‘ON’.  These switches will not operate any functions and the controller power comes on only after the correct sequence has been entered. 4. When  your  controller  is  equipped  with  an  ADDRESS  SELECTOR  SWITCH,  operating  this   switch  will  change  the  system  address,  thus  allowing  a  single  controller  to  operate  multiple controlled machines.  Extreme caution should be used to insure that you do not select the wrong machine.      WARNING: AFTER CHANGING AN ADDRESS OR FREQUENCY SELECTOR SWITCH, YOU  MUST,  IN  THE  FIRST  INSTANCE,  INSURE  THE  TARGETED MACHINE  IS  UNDER  REMOTE  CONTROL  BEFORE  OPERATING  ANY MOTION  FUNCTION  SWITCH.    THIS  MAY  BE  ACCOMPLISHED  BY OPERATING  A  NON  MOTION  FUNCTION  SWITCH  ON  THE  REMOTE CONTROLLER SUCH AS A HORN OR LIGHT.  FAILURE  TO  COMPLY  WITH  THE  ABOVE  WARNING  MAY RESULT  IN THE  UNDESIRED  OPERATION  OF  OTHER  EQUIPMENT  WHICH,  IN TURN, COULD RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 9 General Operating Procedure, continued.   5. Place a convenient and comfortable part of either hand on the PUSH TO OPERATE BAR on top of the controller.  This switch must be depressed and maintained before and when any motor or motion command is initiated.    WARNING: NEVER DISABLE THE PUSH TO OPERATE (PTO) BAR SWITCH ON YOUR REMOTE CONTROLLER.  FAILURE TO COMPLY WITH THIS WARNING MAY  RESULT  IN  DAMAGE  TO  EQUIPMENT,  SERIOUS  INJURY,  OR DEATH.    6.  Operate  the  motion  control  lever  switches  as  required,  remembering  that  the  levers  must  be pulled  upward  for  all  REVERSE  and  UP  motions  and  pushed  down  for  all  FORWARD  and DOWN motions.  A speed increase is obtained by selecting different, appropriately marked lever switches.    Compass  direction  labels  (N,  S,  E,  &  W)  may  be  located  next  to  the  appropriate switches.   7.  While  commanding  a  motion  with  a  switch,  release  the  PUSH  TO  OPERATE  BAR  without centering switch.   The motion must stop - if this does not happen, set the controller’s Power ON/OFF Switch to ‘OFF’ and notify your supervisor immediately.
 Section 3, Page 10    ©03/2007, CATTRON-THEIMEG™ TYPICAL CRANE CONTROL FUNCTIONS.  In  addition  to  the  controls  and  indicators  described  at  the beginning  of  this  section,  some or  all  the control functions described and illustrated below may be applicable to your crane control application.  Unless  notified  to  the  contrary,  the  following  Control  Functions  do  not  require  the  PTO  Bar  to  be pressed to enable their operation.   Figure 3-5.  Crane Paddle Controller - Typical configuration
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 11 TYPICAL CRANE CONTROL FUNCTIONS, continued. 1.  ALARM,  RESET  or  ALARM/RESET  SWITCH.    When  this  momentary  pushbutton  switch located in the center of the PTO bar is used as an ALARM, it operates  a bell, horn, or other warning device on the crane.  When used as a RESET, this switch resets the mainline contactor when it  has previously been switched or tripped OFF due to  a relay failure or  overload, thus allowing power to be  supplied to  the  crane  motors.    When used as an ALARM/RESET, this switch operates the ALARM and RESET functions simultaneously. 2.  MAGNET, VACUUM, or GRAB.  Extra precautions are built into the MAGNET, VACUUM and  GRAB  functions  to  prevent  accidental  release.    Two  momentary  switches  (buttons  or toggles) are normally used for these functions.  Accidental operation of the magnet, vacuum or grab function is minimized by locating these buttons as far as possible from other controls and requires two fingers to release the load.  The Standard Operating Procedure (SOP) for each of these functions is detailed below; however, this procedure may be changed, depending on the system application.  Please note that any deviation from the SOP will be advised in the drawing package supplied with your PRC system.  Magnet  To Lift, press and hold ‘LIFT’ for one second. To Drop, press  and  hold  ‘LIFT’,  wait  for one  second,  then press and hold  ‘DROP’. After load is dropped, release ‘LIFT’ first, then release ‘DROP’.    Vacuum  To Lift, press and hold ‘VACUUM’ for one second. To Drop, press and hold ‘VACUUM’, wait for one second, then press and hold ‘RELEASE’. After  load  is  dropped,  release  ‘VACUUM’  first,  then  release ‘RELEASE’.  Grab    To Close, press ‘CLOSE’. To open, press and hold ‘CLOSE’, then press ‘OPEN’. After grab is opened, release ‘CLOSE’ first, then release ‘OPEN’.   3.  BRAKE SWITCH - This momentary pushbutton or toggle switch is used for manual control of the crane bridge brakes, usually a parking brake, or the second step of a running brake (first step normally comes on when motor is made neutral and released when direction is selected). Other brake functions are available such as PARKING BRAKE RELEASE, COAST, etc. 4.  HOOK/GRAB ROTATE SWITCH - This control function is normally a spring return-to-center (OFF  position)  toggle  switch.    It  allows  a  motorized  hook  or  grab  to  be  turned  in  either  a clockwise (CW) or counter-clockwise (CCW) direction.  5.  CRANE LIGHT ON/OFF SWITCH - This maintained toggle switch provides ON/OFF control of the crane lights.  Proper decoder circuitry insures that they remain latched ‘ON’ if required.
 Section 3, Page 12    ©03/2007, CATTRON-THEIMEG™ TYPICAL CRANE CONTROL FUNCTIONS, continued.  6. CRANE  SELECT  SWITCH  -  This  rotary  selector  or  key  switch  is  used  when  the  controller operates more  than  one crane.  The switch is  used  to  select the  desired  crane by changing the controller's  digital  address.  If  switched  while  the  unit  is  on,  the  power  is  switched  off automatically for 10 seconds, then starts up automatically on the new address. All motor and motion control lever switches on the controller must be neutral during this time.      WARNING: AFTER CHANGING AN ADDRESS OR FREQUENCY SELECTOR SWITCH, YOU  MUST,  IN  THE  FIRST  INSTANCE,    INSURE  THE  TARGETED MACHINE  IS  UNDER  REMOTE  CONTROL  BEFORE  OPERATING  ANY MOTION  FUNCTION  SWITCH.    THIS  MAY  BE  ACCOMPLISHED  BY OPERATING  A  NON  MOTION  FUNCTION  SWITCH  ON  THE  REMOTE CONTROLLER SUCH AS A HORN OR LIGHT.  FAILURE  TO  COMPLY  WITH  THE  ABOVE  WARNING MAY  RESULT  IN THE  UNDESIRED  OPERATION  OF  OTHER  EQUIPMENT  WHICH,  IN TURN, COULD RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.  7.    OPERATOR RELEASE ‘PITCH AND CATCH’ (Optional) – ‘Pitch and catch’ is the operation of a single crane by two, three, or four operators on a first-come, first-served basis. This method provides lock out of the non-commanding operator(s) and allows only one operator at a time. An example of a two operator ‘pitch and catch’ operation follows: 7-1.  The crane is sitting idle and both controllers ‘A’ and ‘B’ are switched OFF. 7-2.  Operator ‘A’ turns his/her controller power to ‘ON’ and captures the crane.  One of two colored lights  on  the  crane,  energized  by  auxiliary  function  relays  in  the  receiver/decoder,  indicates which operator has taken control of the crane.  It should be noted that Operator ‘A’ remains in control even if Operator ‘B’ switches his or her controller power to ‘ON’ and attempts to control the crane – control access is denied to Operator ‘B’ at this time.  7-3. Operator ‘A’ may release the control of the crane to Operator ‘B’ in one of two ways: (1) The  first  way  is  by  pressing  the  ‘RELEASE’  button  on  his/her  controller  (‘pitch’)  after Operator ‘B’ has turned his/her controller power to ‘ON’ and is ready to take control of the crane.   If Controller ‘B’ is transmitting the correct system identification address, Operator ‘B’  is  allowed  to  take  control  (‘catch’).    Operator  ‘A’  is  now  denied  control  access  and should switch his/her controller power to ‘OFF’.  (2) The  second  way  to  transfer  control  from  Operator  ‘A’  to  Operator  ‘B’  is  to  simply  turn Controller ‘A’ power to ‘OFF’ for a designated period of time (typically 45 seconds).  After this period of no transmission, if Controller ‘B’ power is set to ‘ON’ first, Operator ‘B’ will capture the crane.
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 13 TYPICAL LOCOMOTIVE CONTROL FUNCTIONS.  In  addition  to  the  controls  and  indicators  described  at  the beginning  of  this  section,  some or  all  the control  functions  described  and  illustrated  below  may  be  applicable  to  your  locomotive  control application.  Unless notified to the contrary, the following Control Functions do not require the PTO Bar to be pressed to enable their operation.     Figure 3-6.  Locomotive Paddle Controller - Typical Configuration  1. HORN - This momentary push button switch located in the center of the PTO Bar sounds the horn when pressed. 2. HORN/RESET  –  This  momentary  push  button  switch located  in  the  center  of  the  PTO  Bar sounds the horn and provides the initial ‘RESET’ command to the radio receiver/decoder on the locomotive.  This switch must be activated after powering up the controller, otherwise the locomotive will not operate.  Observe that the horn will sound, thus identifying the locomotive is under radio control.
 Section 3, Page 14    ©03/2007, CATTRON-THEIMEG™ TYPICAL LOCOMOTIVE CONTROL FUNCTIONS, continued.  3. DIRECTION SWITCH – this maintained 3-position paddle switch controls ‘FORWARD’ and ‘REVERSE’  functions.    If  the  lever  is  moved  to  the  ‘NEUT’  (neutral  or  center)  position, direction is disabled.  NOTE:  A change in the Locomotive direction will not occur until the throttle is moved to idle for at least 3-seconds.  Attempting to make a change in direction while the throttle is advanced will cause the throttle to return to idle.  Some systems require that an independent brake is applied for 3 seconds, or a specific brake cylinder pressure has been reached, before a change in direction can occur. 4.  THROTTLE LEVER - Controls the Locomotive throttle.  This spring return-to-forward paddle switch spring returns to the ‘IDLE’ position when released.   Note that the PTO Bar must be pressed to enable this control function.  If the PTO Bar is released, the throttle will normally be returned to ‘IDLE’. 5.  INDEPENDENT BRAKE LEVER   - Controls the locomotive (independent) brakes using five maintained lever positions that provide the following braking functions: ‘REL’ -    Releases the brakes.   ‘LAP'  –  Holds the independent brakes at the last applied pressure.   ‘SA’ -      Slow application of the independent brakes.   ‘QA’  -    Quick application of the independent brakes.   ‘EMG’ – Applies train and independent brakes, including the application of sand. Note that the PTO Bar must be pressed to release the brakes.  In most control applications, when the PTO Bar is released, the independent brakes will be slowly applied. 6.  ‘EMG  BRAKE’  SWITCH  –  When  set  to  the  ‘EMG  BRAKE’  position,  this  maintained  2-position toggle switch applies the train and independent brakes, together with the application of sand. 7.  ‘TRAIN’  (AUTOMATIC)  BRAKE  LEVER  -  This  3-position  switch  lever  or  toggle  switch controls the train brakes and has the following functions: APPLY (Momentary) – Applies the railcar brakes by reducing the air supply to the train air line.   HOLD (Maintained) - Seals off the train air line so no further reduction or release will occur.   REL (Maintained) - Puts air into the train air line to release the railcar brakes.
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 15 TYPICAL LOCOMOTIVE CONTROL FUNCTIONS, continued.    8.  SAND – This momentary toggle switch applies sand to the rails in the direction of travel when held in the ‘SAND’ position.   9.  BELL - Sounds the locomotive bell when set to ‘ON’.  This function may be programmed to activate with throttle or direction. 10. HEADLIGHT  ‘OFF/DIM/BRIGHT’  –  this  maintained  3-position  switch  selects  the  desired brightness of the headlight in the direction of travel.  In the ‘BRIGHT’ setting, the headlight at the  front  of  the  locomotive  illuminates  at  full  power,  while  the  headlight  at  the  rear  of  the locomotive or train is dimmed.   In the ‘DIM’ position, both front  and rear headlights  will be dimmed.  11. UNCOUPLE – Provided there is no tractive pull on the couplers, setting this spring return-to-center (OFF position) switch to  ‘FRONT’ or ‘REAR’ will retract  the respective  coupling pin from the front or rear of the locomotive. 12. ALERTER - If equipped with the ‘ALERTER’ option, a switch must be moved by the operator at least once every 20 seconds (or the amount of time you have programmed) or the controller beeper will sound.  If no action is taken within the next 10 seconds, a function is sent to stop the locomotive.  Moving any switch, including the PTO Bar, will reset the Alerter timeout. 13.   OPERATOR  RELEASE  ‘PITCH  AND  CATCH’  (Optional)  –  Locomotive  ‘pitch  and  catch’ allows two operators to swap control to and from each other, based upon which operator should be commanding movement.   Typically, a selector switch mounted on the side of the locomotive mounted Receiver/decoder enclosure is used to select single or dual operator control.   When  the  switch  is  selected  for  two  operators,  the  Receiver/decoder  will  not  allow  the locomotive to operate unless both transmitters are detected.   If at any time, only one transmitter is detected, the throttle will return to idle and the brakes will set.  While in two-operator mode, the primary controller operator will have control of all functions (i.e. throttle, direction, brakes, etc.) and be protected by the controller’s internal tilt switch. The secondary controller operator will maintain control of the ‘HORN’, ‘BELL’, and ‘STOP’ functions, together with other auxiliary functions as designated at the time of system design.  He or she will also be protected by the controller’s internal tilt switch.  For example, should either the primary or secondary operator fall, the Receiver/decoder will stop the locomotive (typically, setting throttle to idle, applying full independent brakes, sounding the horn for 10 minutes and, when installed, activating a ‘MAN DOWN’ alarm).   It must be noted that  the  operator  who  commands  a  tilt  or  ‘STOP’  shutdown  must  also  be  the  one  to ‘RESET’ the shutdown condition.
 Section 3, Page 16    ©03/2007, CATTRON-THEIMEG™ TYPICAL LOCOMOTIVE CONTROL FUNCTIONS, continued.  In a typical locomotive ‘pitch and catch’ application, before a pitch can be made, the following conditions must be satisfied: • The Locomotive must be stopped. • Both controllers must be selecting ‘NEUTRAL’. • Both  controllers  must  have  the  same  selection  on  the  ‘INDEPENDENT’  and ‘AUTOMATIC’ brake override switch. • The  primary  controller  operator  must  depress  the  ‘OPERATOR  RELEASE’ pushbutton. • The  secondary  controller  operator  must  depress  the  ‘OPERATOR  ACCEPT’ pushbutton. As  long  as  the  above  conditions  are  met,  transfer  of  control  will  occur.      In  addition,  if TALKBACK™  is  available on  your  control  system,  a  ‘PRIMARY CONTROL’ indicator will illuminate on the controller in full control.
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 17 Switch Diagnostic Mode. In this mode the operator can easily check that all function switches (motion and non-motion) are fully operational.       WARNING: ELECTRICAL  POWER  TO  THE  TARGET  CONTROLLED  EQUIPMENT MUST BE COMPLETELY ISOLATED TO PREVENT OPERATION UNDER REMOTE CONTROL IN THE SWITCH DIAGNOSTIC MODE.  FAILURE TO COMPLY WITH THE ABOVE WARNING MAY RESULT IN THE  UNDESIRED  OPERATION  OF  EQUIPMENT  WHICH,  IN  TURN, COULD RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.  This is accomplished by first turning off power to the controller using the Power ON/OFF Key and/or Toggle Switch.   Then,  place the  controller  in a tilted  (horizontal) position with its battery door face down.    To  enable  the  switch  diagnostic  mode,  re-apply  power  using  the  Power  ON/OFF Switch(es) while the controller is in the horizontal position.  This  mode  of  diagnostics  activates  the  beeper  when  (1)  each  non-motion  (auxiliary)  toggle  and pushbutton switch changes state, and (2) when any motion control lever/switch changes state, provided the PTO Bar is pressed and held down each time the motion lever/switch changes state.    For  example,  push  any  one  of  the  auxiliary  toggle  switches  UP  and  a  single  ‘beep’  will  be  heard.  Release the toggle switch and another single ‘beep’ will be heard as the switch spring returns to center.  Repeat this procedure on the remaining non-motion toggle and pushbutton switches in both UP/DOWN or ON/OFF positions.  If the switches are functioning correctly, a ‘beep’ will be heard each time the switch changes state.  Repeat the above procedure on all motion control levers/switches, remembering to enable these motion functions by pressing and holding the PTO Bar down when operating a lever/switch.  When an enabled motion lever/switch is functioning correctly, a ‘beep’ will be heard each time the device changes state. To disable the switch diagnostic mode, simply turn the controller power to ‘OFF’, then re-apply power to the controller while it is in an upright position.
 Section 3, Page 18    ©03/2007, CATTRON-THEIMEG™ Battery Packs and Battery Pack Charging. The following battery pack and charging options are available for your controller and may be ordered from your nearest CATTRON-THEIMEG™ facility identified on the back page of this manual. Alkaline  Battery  Pack  providing  75  hours  of  continuous  operation.    This  battery  pack  is  not re-chargeable and should be discarded when exhausted. Nickel-Cadmium (Ni-Cad) Battery Pack providing approximately 23 hours of continuous operation.  This battery pack is re-chargeable using the CATTRON-THEIMEG™ 70C-0004 Battery Conditioner.  Table 3-1.  Battery Pack Options CATTRON-THEIMEG™ PART NUMBER TYPE  COLOR LIFE OPERATING HOURS RE-CHARGING TIME (using 70C-0004  Conditioner/charger) LIFETIME CYCLES C-8096  Ni-Cad Battery Pack Yellow  23*               3-Hours  200+ 60C-0023  Alkaline Battery Pack White  75*   Do Not Charge  1  * Battery life operating hours are based on continuous transmissions. Battery  Conditioner -  A  CATTRON-THEIMEG™  Battery  Conditioner  (Part  #  70C-0004)  is available for use with CATTRON-THEIMEG™ C-8096 Ni-Cad Battery packs only.    Battery Pack Replacement. When the TRANSMIT/LOW BATTERY LED starts flashing red, this alerts the operator that he or she has approximately one hour of continuous operation remaining, after which the battery pack must be replaced or re-charged.  Replace the battery pack as follows: 1. Set the controller’s Power ON/OFF Switch(es) to the ‘OFF’ position.  2. Referring to Figure 3-7 opposite, unlock the battery door by inserting a coin into the slot and twisting. 3.  Open the battery door and lift the battery pack out of the tray.  4.  Install  a  fresh,  fully  charged  battery  pack  in  the  controller,  making  sure  the  contacts  on  the underside of the battery pack locate with their corresponding pick-up contacts in the battery tray.
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 19 Battery Pack Replacement, continued. 5.  Close the battery door and secure by pressing firmly until it snaps into the locked position.  6.  Set the controller’s Power ON/OFF Switch(es) to ‘ON’.   Observe that the TRANSMIT/LOW BATTERY LED momentarily flashes yellow and two quick beeps are heard.  When resuming your remote control operation, observe the TRANSMIT/LOW BATTERY LED as you operate a non-motion function toggle switch such as a horn or light.  If this LED is now flashing green, your controller is fully operational. Figure 3-7.  Battery Pack Replacement.
 Section 3, Page 20    ©03/2007, CATTRON-THEIMEG™ Ni-Cad Battery Pack Conditioning/Charging (Figure 3-8).   CAUTIONS: (1) CATTRON-THEIMEG™  Battery  Conditioners  are  designed  for  use  with CATTRON-THEIMEG™ Ni-Cad Battery Packs only.   (2) Battery Packs must be removed or disconnected from Battery Conditioners within 48-hours of achieving the fully charged state.   Failure to comply with these Cautions  may result in equipment and/or battery damage and will void our warranty.   A  Ni-Cad  battery  pack  must  be  removed  from  the  controller’s  battery  compartment  for  external charging.  The Battery Conditioner includes a Mains VAC Adaptor that allows operation from mains supply voltages between 100 and 240VAC @ 50/60 kHz.   Referring to Figure 3-8 opposite, this adaptor is connected as shown.  Similarly, when installing the Ni-Cad Battery Pack to the Battery Conditioner, refer to Figure 3-8 for the appropriate locating instructions.  The Battery Conditioner automatically conditions the battery pack by first discharging it at 600mA for 2-hours before applying a rapid charge for 1-hour.  The conditioner incorporates end of charge detection circuitry to  accurately sense when  the battery pack is fully  charged.    When this  condition  has been detected, the conditioner switches to a ‘trickle’ mode that keeps the battery pack fully charged and ready to  use  for  up  to  48-hours.    To  prevent  damage  to  the  battery  pack,  it  should  be  removed  from  the conditioner within 48-hours of achieving a fully charged state. The CATTRON-THEIMEG™ Battery Conditioner incorporates an LED that indicates status as follows: Amber Color – indicates the battery pack is being discharged. Red Color - indicates the battery pack is being charged at a rapid rate. Green Color - indicates the battery pack is fully  charged and  that a  ‘trickle’ charge is  being applied to maintain  the fully charged  state.  The  battery pack is  ready  for use and  should  be removed from the conditioner within 48-hours.
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 21 Ni-Cad Battery Pack Conditioning/Charging , continued. Figure 3-8.  Ni -Cad Battery Pack Conditioning – interconnection details. 1.  REAR VIEW - CONNECTING THE VAC ADAPTOR2.  FRONT VIEW - INSTALLING THE BATTERY PACKOUTPUT JACKFROM MAINSVAC ADAPTORMAINS VAC ADAPTORVAC OUTLET18 VDC INPUT SOCKETBATTERY CONDITIONER(PART # 70C-0004)STATUSLEDNi-Cad BATTERY PACK(PART # C8096)
 Section 3, Page 22    ©03/2007, CATTRON-THEIMEG™ Pre-programmed Frequency Selection. If your Controller will be used to operate more than one crane, locomotive, or controlled machine, or be used as a spare controller for multiple remote control systems, up to sixteen selectable frequencies may have been factory pre-programmed into the controller’s EPROM.  To see if this selectable frequency option applies to your controller, refer to Figure 3-7 above and locate the serial tag on the inside of the battery door.   If the serial tag indicates a specific frequency in the FREQ line (i.e., 448.1000 MHz) the selectable pre-programmed frequency option does not apply to your controller.    If the serial tag indicates ‘SELECTABLE’ in the FREQ. line, refer to the frequency chart provided in your  custom  drawing  package.    This  frequency  chart  will  specify  the  pre-programmed  channel frequencies available with your controller.
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 23 Pre-programmed Frequency Selection, continued.     WARNING: MORE  THAN  ONE  REMOTE  CONTROL  SYSTEM  MAY  BE  USED  AT, AROUND,  OR  NEARBY  YOUR  OPERATING  FACILITY.    THEREFORE, YOU MUST INSURE THE FREQUENCY OF YOUR PADDLE CONTROLLER EXACTLY MATCHES THE FREQUENCY OF THE DESIRED EQUIPMENT TO BE OPERATED. FAILURE TO COMPLY WITH THE ABOVE WARNING MAY RESULT IN THE  UNDESIRED  OPERATION  OF  OTHER  EQUIPMENT  WHICH,  IN TURN, COULD RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.  To select a pre-programmed frequency, proceed as follows: 1. Record the operating frequency of the intended equipment to be controlled – this may be found on the front cover of the manual provided with the target receiver/decoder, or on a serial tag located inside the target receiver/decoder enclosure. 2. Referring to the Frequency Chart supplied with your controller drawing package, locate the controller frequency that matches the equipment operating frequency recorded in the previous step, noting its corresponding Channel Address Number which may be from ‘0’ thru ‘7’ or ‘A’ thru ‘F’. 3. Set the controller’s Power ON/OFF Switch(es) to ‘OFF’.   4. Referring to Figure 3-7 above, unlock the battery door by inserting a coin into the slot and twisting. 5. Open the battery door and remove the battery pack.   6. Referring to  Figure 3-9  overleaf, set the four Frequency Channel Selector  Switches to select the Channel Address Number previously noted in step 2., above.   7. Replace the battery pack in the unit, making sure the contacts on the underside of the battery pack locate with their corresponding pick-up contacts in the battery tray.   Close the battery door and secure by pressing firmly until it snaps into the locked position.  8. Set  the  controller’s  Power  ON/OFF  Switch(es)  to  ‘ON’.  Observe  that  the TRANSMIT/LOW BATTERY LED momentarily flashes yellow and two quick beeps are heard.  9. Operate a non-motion function such as a horn or light on the target equipment using the appropriate toggle switch and observe the TRANSMIT/LOW BATTERY LED and the selected horn or light.   If the  LED  flashes  green and the  horn  or  light  activates,  your controller is fully operational.
 Section 3, Page 24    ©03/2007, CATTRON-THEIMEG™ Pre-programmed Frequency Selection, continued.  Figure 3-9.  Pre-programmed Frequency Selection
 ©03/2007, CATTRON-THEIMEG™     Section 3, Page 25 Pre-programmed Option Selection. Because  each  paddle  controller  has  been  designed  and  custom  built  for  a  specific  remote  control application, the OPTION SELECT SWITCH UNIT (refer to Figure 3-9, opposite) may have been pre-configured  with  one  of  three  discrete  programming  options.    It  should  be  noted  that  the  exact  switch configuration  will  depend  upon  the  firmware  selected  by  your  CATTRON-THEIMEG™  Applications Engineer at the time your PRRC system was designed.  When applicable, a programming option may be selected from one of the following:  1. Up  to  16  frequency  only  select  (factory  programmed)  –  refer  to  ‘Pre-programmed Frequency Selection’ in this Section for complete details. 2. 4-frequency select (factory programmed). 3.  Up to 16 selection options - each position may be factory  programmed  with one of the following: a)  Transmit frequency b) Transmit address c) Timesharing pattern  Refer to the specific information in the custom engineered drawing package provided with your controller to determine the exact configuration of the OPTION SELECT SWITCH UNIT and the pre-programmed option (if any).   When applicable to your controller, specific switch selections for a given pre-programmed option will be provided.        END OF SECTION
 Section 3, Page 26    ©03/2007, CATTRON-THEIMEG™          This page intentionally left blank
 ©03/2007, CATTRON-THEIMEG™     Section 4, Page 1 Section 4 – Maintenance Instructions CATTRON-THEIMEG™ Maintenance Philosophy. Our maintenance philosophy is that inoperative Paddle Controllers are returned as complete units to our workshops for repair.  This is because (a) each controller is customized for a specific control application which  severely  restricts  component/part  interchangeability,  (b)  the  internal  circuit  board  and microprocessor is extremely sensitive to electrostatic discharge, and (c) internal components are highly miniaturized and assembled to within very close tolerances.  However, CATTRON-THEIMEG™ will permit certain preventive and corrective maintenance to be performed without voiding our warranty, as follows:    Preventive Maintenance is a periodic check of the system to keep it functioning at peak performance. Preventive  maintenance  can  also  help  prevent  breakdowns  and  equipment  outages  by  identifying potential problems before they become real problems.  Corrective  Maintenance  refers  to  fixing  a  problem  once  it  has  occurred.  The  goal  of  corrective maintenance  is  to  get  the  system  back  on  line  as  quickly  as  possible  with  a  minimum  impact  on operations. Preventive maintenance. Preventive maintenance  for CATTRON-THEIMEG™  Paddle  Controllers is minimal because they  are extremely durable and reliable units.  Preventive maintenance procedures are detailed in the following sub paragraphs: Daily Visual Inspection. Before  use,  visually  inspect  the  controller  for  cleanliness,  physical  damage,  and  security  of  external parts  (screws,  switches,  rubber  grips,  etc.).    CATTRON-THEIMEG™  emphasizes  that  regular  visual inspections not only mean quickly locating a source of potential problems, but also may prevent serious problems from developing later. Special RF Test (CATTRON-THEIMEG™ trained technicians only). The special RF test mode is a diagnostic mode that is incorporated in your Paddle Controller.  Controller outputs  can  be  monitored  on  a  spectrum  analyzer/communication  service  monitor  set  to  the  same frequency as the controller.   We emphasize this procedure is only for use by customer technicians that have been trained by ourselves where further details are presented during the CATTRON-THEIMEG™ training course.     For information purposes, the actual  RF test  procedure is summarized  on the  next page:
 Section 4, Page 2    ©03/2007, CATTRON-THEIMEG™ Special RF Test, continued. With PTO Bar switch depressed, setting the ON/OFF KEYSWITCH to ‘ON’ will transmit a continuous beep and the green LED will illuminate continuously.  Continually cycling (pressing and releasing) the PTO bar switch three times will initiate the RF diagnostic sequence (the beep will stop).  Further PTO bar switch cycling will make the controller transmit the following: CYCLE    CONTROLLER TRANSMISSION 4    Maximum Low Frequency (a frequency 2.4 kHz lower than carrier) 5    Q- Sync (center of carrier) 6    Maximum High Frequency (a frequency 2.4 kHz  higher than carrier) 7    2 kHz modulating sine wave (tone) 8    1-2-2-1 pattern square wave Annual Netting Check. Netting  means  that  the  receiver  and  transmitter  of  the  radio  control  system  are  aligned  on  the  same frequency.  It is very important that the receiver is exactly tuned to the frequency required. This check should be done once a year by a qualified radio technician utilizing calibrated test equipment. Troubleshooting. A  basic  Troubleshooting  Guide  is  provided  on  page  3  of  this  section.    For  safety  reasons,  when troubleshooting the Paddle controller, the power supply to the target equipment motors and all motion functions must be completely isolated to prevent operation under remote control.  However, the other major components of the remote control system (power supply and receiver/decoder) should be  fully operational.  The remote control operator should also be located within 500 feet (160+ meters) of the target receiver/decoder.
 ©03/2007, CATTRON-THEIMEG™     Section 4, Page 3 Troubleshooting Guide.  WARNINGELECTRICAL POWER TO THE TARGET CONTROLLEDEQUIPMENT MUST BE COMPLETELY ISOLATED TO PREVENT OPERATION UNDER REMOTE CONTROLIN THE SWITCH DIAGNOSTIC MODE.FAILURE TO COMPLY WITH THIS WARNING MAY RESULTIN THE UNDESIRED OPERATION OF EQUIPMENTWHICH, IN TURN, COULD RESULT IN SERIOUS INJURY OR DEATH TO PERSONNEL AND DAMAGE TO EQUIPMENT.
 Section 4, Page 4    ©03/2007, CATTRON-THEIMEG™ Corrective maintenance. Corrective maintenance for the Paddle Controller is restricted to replacing the Battery Pack, Address Code  Plug,  Paddle  Levers  and,  when  installed,  the  External  Antenna.  Refer  to  the  Replacement Procedures below when removing and replacing items.  Having replaced an item, and before placing the Paddle Controller into operational service, carry out a Functional Check as follows:  Functional Check. 1.  Set  the  controller’s  Power  ON/OFF  Switch(es)  to  ‘ON’.    Observe  that  the TRANSMIT/LOW BATTERY LED momentarily flashes yellow and two quick ‘beeps’ are heard.  2.  Operate a non-motion function such as a horn or light on the target equipment using the appropriate  toggle  switch  and  observe  the  TRANSMIT/LOW  BATTERY  LED  which should flash green. 3.  Set the controller’s Power ON/OFF Switch(es) to ‘OFF’.   4.  Operate  the controller  in  Switch Diagnostic Mode (refer  to  Section  3  for  procedure), insuring all toggle, pushbutton, and paddle lever function switches are fully operational.  Replacement Items. Replacement  items  and  accessories  for  your  controller  may  be  ordered  direct  from  CATTRON-THEIMEG™.    To  order  replacement  items,  refer  to  Section  5  of  this  manual  for  details  and  part numbers.   Replacement Procedures. Battery Pack Replacement. To replace the battery pack, proceed as follows: 1. Set the controller’s Power ON/OFF Switch(es) to ‘OFF’.  2. Referring to Figure 4-1 opposite, unlock the battery door by inserting a coin into the slot and twisting.  3. Open the battery door and lift the battery pack out of the tray. 4. Install a fresh or fully charged battery pack in the unit, making sure the contacts on the underside  of  the  battery  pack  locate  with  their  corresponding  pick-up  contacts  in  the battery tray. 5. Close  the  battery  door  and  secure  by  pressing  firmly  until  it  snaps  into  the  locked position. 6. Carry out a Functional Check on the controller – refer to the above paragraph for details.
 ©03/2007, CATTRON-THEIMEG™     Section 4, Page 5 Battery Pack Replacement, continued. Figure 4-1.  Battery Pack Replacement.  Address Code Plug Replacement. Each CATTRON-THEIMEG™ Paddle Controller is equipped with a code plug. This code plug sets the address of the controller which should always match the address of the target receiver/decoder.  When a command is received by the receiver/decoder, the address of the controller sending the signal is checked against the address of the receiver/decoder.  If the addresses do not match, the signal is ignored and an error  message  is  displayed  on  the  receiver/decoder.    For  safety  reasons,  it  is  important  that  no  two controllers  at  a  location  use  the  same  address  settings.  This  could  cause  operation  of  undesired equipment resulting in damage to equipment and/or personal injury. While the factory address setting will be adequate for most users, there may be conditions where it is necessary to change the address code.  Such conditions include the use of a spare controller, or when your controller will be used to operate more than one crane, locomotive, or controlled machine.  Before making any change in the address code setting, you will be required to identify the address code of the target receiver/decoder. The code assigned to the receiver/decoder at the factory is found on a serial tag located inside the target receiver/decoder.  For  information  on  setting  the  address  code  for  your  receiver/decoder,  refer  to  the documentation provided with the receiver/decoder.
 Section 4, Page 6    ©03/2007, CATTRON-THEIMEG™ Address Code Plug Replacement, continued.    WARNINGS: UNCODED  ADDRESS  PLUG(S)  SHALL  BE  PROGRAMMED  WITH  THE SAME  ADDRESS  CODE  AS  SET  IN  THE  TARGET  RECEIVER/DECODER.    IT  SHOULD  BE  FULLY  UNDERSTOOD  THAT  CATTRON-THEIMEG™ SHALL  NOT  BE  HELD  LIABLE  FOR  PERSONAL  INJURY,  DEATH, EQUIPMENT  OR  PROPERTY  DAMAGE  ARISING  FROM  DUPLICATED, INCORRECTLY PROGRAMMED OR INCORRECT CODE PLUG USAGE. IT  IS  YOUR  RESPONSIBILITY  TO  ESTABLISH  A  PROCEDURE  THAT INSURES  ONLY  THE  CODE  PLUG  CONFIGURED  FOR  A  PARTICULAR ADDRESS  IS  INSTALLED  IN  EQUIPMENT  DESIGNED  TO  OPERATE  ON THE  SAME  ADDRESS.    NEVER  PUT  MORE  THAN  ONE  CONTROLLER INTO  OPERATION  ON  THE  SAME  ADDRESS  AT  ANY  GIVEN  TIME.  CATTRON-THEIMEG™  STRONGLY  ADVISES  YOU  TO  IMPLEMENT  AND REGULARLY  UPDATE  A  REGISTER  OF  INDIVIDUAL  ADDRESSES  AND OPERATING  FREQUENCIES  ASSIGNED  TO  EACH  PORTABLE  RADIO REMOTE  CONTROL  (PRRC)  SYSTEM  LOCATED  AT  YOUR  OPERATING FACILITY.     IN ADDITION, ANY  SPARE  CODE  PLUGS, OR  CODE PLUGS INSTALLED  IN  EQUIPMENT  THAT  ARE  CONFIGURED  FOR  THE  SAME ADDRESS OF EQUIPMENT THAT IS IN SERVICE, MUST BE HELD UNDER LOCK AND KEY BY A DESIGNATED SUPERVISOR.   FAILURE  TO  COMPLY  WITH  THESE  WARNINGS  MAY  RESULT  IN OPERATION  OF  UNDESIRED  EQUIPMENT  WHICH  IN  TURN  COULD RESULT  IN  PERSONAL  INJURY  OR  DEATH  TO  PERSONNEL  AND DAMAGE TO EQUIPMENT. CATTRON-THEIMEG™ sets the address code of all paddle controllers before they leave the factory.  If the  code  must  be  changed,  a  new  code  plug  with  the  new  address  code  must  be  obtained  from CATTRON-THEIMEG™.    In  some  circumstances  CATTRON-THEIMEG™  may  provide  blank,  or unset, code plugs.  An unset code plug must have a code set prior to installing in the decoder.  This is described  in  the  procedure  below.    Installing  an  unset  code  plug  in  the  controller  will  prevent  the controller from operating. To replace the code plug for your Paddle Controller, proceed as follows: 1. Set the controller’s Power ON/OFF Switch(es) to ‘OFF’.  2. Record the address code of the intended equipment to be controlled – this may be found on the front cover of the manual provided with the target receiver/decoder, or on a serial tag located inside the target receiver/decoder enclosure. 3. Referring to Figure 4-1 above, unlock the battery door by inserting a coin into the slot and twisting. 4. Open the battery door and lift the battery pack out of the tray.
 ©03/2007, CATTRON-THEIMEG™     Section 4, Page 7 Address Code Plug Replacement, continued. 5.  Referring to Figure 4-2 below, using a pair of small flat nosed pliers, remove the existing ‘set’ code plug by pulling it straight up and away from its battery compartment location.  We  recommend  you:  (1)  tag  the  removed  code  plug  with  the  serial  number  of  the controller, and (2) deposit the code plug in a safe place under lock and key. Figure 4-2.  Code Plug Location. BATTERYCOMPARTMENT‘SET’ CODEPLUG
 Section 4, Page 8    ©03/2007, CATTRON-THEIMEG™ Address Code Plug Replacement, continued. 6.  If the new code plug is blank (unset), set the new address code previously recorded in Step 2.  To set the code, pins 2 through 8 must be cut in a specific pattern.  Figure 4-3 below shows all possible address codes for the code plug.   For example, to set the code plug to Address Code 14, pins 4, and 6 must be cut.  DO NOT cut Pins 1, 9 and 10. Figure 4-3.  Code plug settings.
 ©03/2007, CATTRON-THEIMEG™     Section 4, Page 9 Address Code Plug Replacement, continued. 7. Write the newly set address code on the side of the code plug using a permanent marker.  8. Carefully install the new code plug, making sure the spot (Pin 1) is positioned as shown in Figure 4-2, above. 9. Referring  to  Figure  4-1  above,  replace  the  battery  pack  in  the  unit,  making  sure  the contacts  on  the  underside  of  the  battery  pack  locate  with  their  corresponding  pick-up contacts in the battery tray.  10. Close  the  battery  door  and  secure  by  pressing  firmly  until  it  snaps  into  the  locked position. 11. Carry  out  a  Functional  Check on  the  controller  –  refer  to  page  4  of  this  Section  for details. Paddle Lever Replacement, (Figure 4-4). 1. To replace a Paddle Lever, remove Screw (1) using a 6/32" hexagonal key and withdraw Lever (2) from Shaft (3). 2. Install a new Lever (2) to the Shaft (3) and secure using Screw (1). Figure 4-4.  Lever Replacement.  External Antenna Replacement, (Figure 4-5).   1. Remove the External Antenna (1) by pushing down and unscrewing the BNC connector (2) half-a-turn in a counter-clockwise direction from its connector socket (3) located on the lower front plate of the controller. 2. The new Antenna (1) is simply installed by screwing the BNC connector (2) clockwise until  it  ‘clicks’  into  the  connector  socket  (3)  located  on  the  lower  front  plate  of  the controller. 1.  SCREW2.  LEVER3.  SHAFT123
 Section 4, Page 10    ©03/2007, CATTRON-THEIMEG™ External Antenna Replacement, continued.  Figure 4-5.  External Antenna Replacement. 123      END OF SECTION
 ©03/2007, CATTRON-THEIMEG™     Section 5, Page 1 Section 5 – Replacement Items and Accessories Notable differences between Paddle Controllers will include the quantity, type, and placement of toggle, paddle,  and  pushbutton  switches.    For  an  individual  controller’s  exact  switch  and  indicator configuration, including quantities and part numbers, you should refer to the schematic drawing originally supplied with the paddle controller. Note:  Replacement items identified in Figure 5-1 overleaf should only be installed by approved customer technicians who have attended the CATTRON-THEIMEG™ Technician Training Course.    Referring to the illustration overleaf (Figure 5-1): • Two types of Pushbutton Switch Assemblies are available - cross refer to Table 5-1 below    • Toggle Switch Assemblies are supplied in a variety of configurations - cross refer to Table 5-2 below. • Items 1 through 29 are common to most paddle controllers  - cross refer to Table 5-3. Table 5-1.  Pushbutton  Switch Assemblies COMPONENT DESCRIPTION  CATTRON-THEIMEG™  PART NUMBER RED PUSHBUTTON  40C-0308 GRAY PUSHBUTTON  40C-0308GRY Table 5-2.  Toggle Switch Assemblies COMPONENT DESCRIPTION  SWITCH BODY* IDENTIFIER  CATTRON-THEIMEG™  PART NUMBER ON-OFF-ON   12TW1-1  40C-0112 ON-OFF-ON LKG.   12TW1-1A  40C-0356 ON-OFF   12TW1-3  40C-0005 ON-OFF LKG.   12TW1-3D  40C-0337 ON-OFF-(ON)   12TW1-5  40C-0113 ON-OFF-(LIFT ON)   12TW1-5N  40C-0315 (ON) OFF (ON)   12TW1-7  40C-0111 (LIFT ON) OFF (LIFT ON)   12TW1-7E  40C-0347 OFF (ON)   12TW1-8  40C-0170 OFF (LIFT ON)   12TW1-8F  40C-0303 * The identifier number is engraved on the switch body
 Section 5, Page 2    ©03/2007, CATTRON-THEIMEG™ 123Figure 5-1.  Exploded View99B9A6781054211121124251726 272829161614D14A14B1414C15E1515A15B15C15D19131820212223PUSHBUTTONSWITCHASSEMBLIES (see Table 2)TOGGLE SWITCHASSEMBLIES (see Table 3)
 ©03/2007, CATTRON-THEIMEG™     Section 5, Page 3 Table 5-3.  Common items FIGURE 5-1, ITEM NUMBER COMPONENT DESCRIPTION  QUANTITY PER ASSEMBLY CATTRON-THEIMEG™  PART NUMBER 1  Screw, Truss Head, Phillips, 8-32 x 5/8"  20  03C-0094 2  Screw, Truss Head, Phillips, 8-32 x 1"  2  03C-0099 3  RH Endcap Assembly, with Sonalert  1  01C-0126 -  … Gasket, RH Endcap  1  32C-0092R 4  Washer/Spacer  8  04C-0027 5  Bracket Ring for carrying harness  4  07-83585B01 6  Front Housing, 3-Motor  1  15C-0115F -  Front Housing, 4-Motor*  1  15C-0115F4 7  Battery Housing, complete  1  01C-0115R-01 8  Encoder Board**  1  E840/M840P Series 9  PTO Bar Assembly, c/w Tab & Label  1  01C-0276WA-01 9A  ... Tab, PTO  1  15C-0114A-01 9B  ... Label  1  54C-0107WA 10  LH Endcap Assembly  1  01C-0125 -  … Gasket, LH Endcap  1  32C-0092L 11  Switch, Keylock with Keynob and wires  1  01C-40C-0369K 12  Key, complete with Hexagonal Knob  1  55C-0369K 13  Lever Switch Assembly RH  As Required  CPA-0274 14  Lever Switch Assembly LH  As Required  CPA-0275 14A  ... LH Side Plate, c/w Standoff  1  15C-0057 14B  ... Side Plate, Blank, RH or LH  1  15C-0059 14C  ... Screw, Truss Hd, Phillips, 4-40 x 3/8"  4  03C-0096 14D  ... Housing, Single  1  15C-01125S 15  Lever Switch Assembly, Dual  As Required  CPA-0276 15A  ... RH Side Plate, c/w Standoff  1  15C-0058 15B  ... LH Side Plate, c/w Standoff  1  15C-0057 15C  ... Screw, Flat  Hd, Phillips, 4-40 x 3/8"  4  03C-0096 15D  ... Gear Cap  1  15C-135-3274 15E  ... Housing, Dual  1  15C-0112D 16  Screw, Truss Head, Phillips, 6-32 x 3/8"  As Required  03C-0095
 Section 5, Page 4    ©03/2007, CATTRON-THEIMEG™ Table 5-3.  Common items, continued FIGURE 5-1, ITEM NUMBER COMPONENT DESCRIPTION  QUANTITY PER ASSEMBLY CATTRON-THEIMEG™  PART NUMBER 17  Lever, Left Hand  As Required  36-83735D03-LEX 18  Lever, Right Hand  As Required  36-83735D01-LEX 19  Screw, Hex, Set, 6-32 x 0.5", SS, Lever  As Required   03-83641C01 20  Screw, Truss Head, Phillips, 6-32 x 1/4"  As Required  03C-0100 21  LED, Non-diffused, Red/Green  1  40C-0227 22  Battery Cover, with Gasket  1  01C-0278-01 23  Bottom Housing, 3 & 4-Paddle  1  15C-0115B 24  Antenna, 402-470MHz**  1  CAE-6007SYN 25  Screw, Truss Head, Phillips, 4-40 x 1/4"  2  03C-0098 26  Nut, Hex, Encl Top, 15-32   As Required  02C-0011 27  Washer, Sealing, 15/32-32, Switch Panel  As Required  04C-0047 28  Gasket, Single  As Required  32C-0032 29  Gasket, Dual  As Required  32C-0033    * Alternative ** see schematic drawing originally supplied with controller for correct part number.
 ©03/2007, CATTRON-THEIMEG™     Section 5, Page 5 Consumable Items and Optional Accessories. Consumable  Items  and  Optional  Accessories  are  listed  in  Table  5-4  below  and  illustrated  on  the following pages.    Table 5-4.  Consumable Items and Optional Accessories Item Number CATTRON-THEIMEG™ Part Number Order Quantity Item Description 1  60C-0023  1  Battery pack, Alkaline, 12.5V, non-rechargeable 2  C-8096  1  Battery pack, Ni-Cad, re-chargeable, 12.5V, 850 mAH 3  70C-0004  1  Battery Conditioner, 100-240 VAC input  4  CLN-6095  1  Carrying Harness, Standard, small *  CLN-6096  -  Carrying Harness, Standard, large *  CLN-6096XL  -  Carrying Harness, Standard, extra large 5  CLN-300901XS  1  Carrying Harness, Low Back Support, extra small *  CLN-300902S  -  Carrying Harness, Low Back Support, small *  CLN-300903M  -  Carrying Harness, Low Back Support, medium *  CLN-300904L  -  Carrying Harness, Low Back Support, large *  CLN-300905XL  -  Carrying Harness, Low Back Support, extra large *  CLN-300906XXL -  Carrying  Harness,  Low  Back  Support,  double  extra large *  CLN-300907XXXL  -  Carrying  Harness,  Low  Back  Support,  triple  extra large 6  06C-0232  1  Code Plug, Unprogrammed 7  06C-0232P  1  Code Plug, Programmed 8  36C-0066  1  Custom Lever, Right Hand, Blank, threaded 9  36C-0067  1  Custom Lever, Left Hand, Blank, threaded 10  36C-0073-O   1    Knob, Oval, for Items 8 and 9 above 11  36C-0073-S  1    Knob, Square, for Items 8 and 9 above  12  36C-0073-C  1    Knob, Cylindrical, for Items 8 and 9 above 13  36C-0073-H  1    Knob, Hexagonal, for Items 8 and 9 above     * = alternative
 Section 5, Page 6    ©03/2007, CATTRON-THEIMEG™ Consumable Items and Optional Accessories, continued.     Item 1 – Part Number 60C-0023         Item 2 – Part Number C-8096       Item 3 – Part Number 70C-0004  MULTI-VOLTAGE ADAPTERBATTERY PACK CONDITIONERPART NUMBER 70C-0004 NON RE-CHARGEABLEALKALINE BATTERY PACK         (white color)RE-CHARGEABLENI-CAD BATTERY PACK       (yellow color)
 ©03/2007, CATTRON-THEIMEG™     Section 5, Page 7 Consumable Items and Optional Accessories, continued.   Item 4 – Part Number CLN-609Series        Item 5 – Part Number CLN-3009Series   Item 6 – Part Number 06C-0232         Item 7 – Part Number 06C-0232P STANDARDCARRYINGHARNESSLOW BACKSUPPORTCARRYINGHARNESSStandard Carrying Harnesses are available in 2 sizes as follows:CLN-6096                     Small to Large                    37.5 - 56 inchesCLN-6096XL                Extra Large                           48 - 68 inchesLow Back Support Carrying Harnesses are available as follows:CLN-300902S                 Small                                      32 - 36 inchesCLN-300903M                Medium                                  36 - 40 inchesCLN-300904L                 Large                                      40 - 44 inchesCLN-300905XL              Extra Large                            44 - 48 inchesCLN-300906XXL           Double Extra Large               48 - 52 inchesCLN-300907XXXL        Triple Extra Large                 52 - 56 inchesCLN-300901XS              Extra Small                             28 - 32 inches
 Section 5, Page 8    ©03/2007, CATTRON-THEIMEG™  Consumable Items and Optional Accessories, continued.  Item 8 – Part Number 36C-0066      Item 9 – Part Number 36C-0067    Item 10 – Part Number 36C-0073-O      Item 11 – Part Number 36C-0073-S    Item 12 – Part Number 36C-0073-C      Item 13 – Part Number 36C-0073-H      END OF SECTION   CUSTOM RIGHTHAND LEVERCUSTOM LEFTHAND LEVER OVALKNOBSQUAREKNOBCYLINDRICALKNOB HEXAGONALKNOB
 03/2007, CATTRON-THEIMEG™   Index i Index A Accessories  ..................................... 5-5 Address code ................................... 2-1 Applications .................................... 1-3 Automatic safety override ............... 2-1 B Battery Pack Conditioner ...... 3-18, 5-2 Battery door  ................................. 3-18 Battery pack conditioning ............ 3-20 Battery pack options  ..............1-2, 3-18 Battery pack replacement....... 3-18, 4-4 Battery Saver ...................................1-2 C Carrying harnesses ................  3-5 - 3-7 Code plug replacement .................... 4-5 Controls and indicators  ................... 3-1 Corrective maintenance  .................. 4-4 Crane Control Functions (typical) ...3-10 Custom paddle levers & knobs ........ 5-7 D Data error checking ........................  2-2 F Frequency options ..........................  1-3 Frequency selection  ....................   3-22 Frequently asked questions.............. 1-3 Functional check ............................  4-4 G General operating procedure ..........  3-5 I Intelligent digital message protocol   2-1 L Lever switch placement  ...................1-2 Lever replacement ........................... 4-9 List of abbreviations  ......................... iii Locomotive Control Functions  ....  3-13 M Maintenance instructions  ...............  4-1 Maintenance philosophy ................  4-1 N Netting check  ...............................   4-2 Notable performance & safety    Features  ................................   1-2 O Operate (OPR) relay  .................... .. 2-1 Operating frequency ..................... .. 1-3 Operating instructions .................. .. 3-1 Optional accessories ..................... .. 5-3  Overview, remote control systems .. 1-7
 Index ii    ©03/2007, CATTRON-THEIMEG™ Index P Paddle switch placement ................  1-2 Power On Self Test (POST) ...........  1-2 Power ON/OFF switch ............. 3-1, 3-2  Preventive maintenance  .................  4-2 Push To Operate bar switch...... 2-2, 3-2 R Radio control operator’s duties:   General Equipment .................  2-4   EOT Crane ............................   2-8   Locomotive ...........................  2-12 Replacement items ................... 4-4, 5-1 Replacements:   Battery pack ............................  4-4   Address code plug  ................... 4-5   Paddle lever  ............................  4-9   External Antenna ....................  4-9    S Safety considerations  ...................   2-1 Safety & security features ............   2-1 Side mounted levers ...............  1-2, 3-2 Standard specifications .................   1-5 Switches  .................................  3-2, 3-3 Switch diagnostic mode ................  3-17 T TALKBACKTM option  ..................   3-3 Technical Abbreviations  .................  iii Transmit/Low Battery indicator ....   3-3 Troubleshooting guide ..................   4-3 Typical method of operation ........   2-2
 03/2007, CATTRON-THEIMEG™   Cranesafety – page 1  RECOMMENDED SAFETY RULES FOR PORTABLE REMOTE CONTROLLED (PRC) CRANES For  the  purpose  of  these  rules,  Portable  Remote  Control  or  PRC  refers  to  Radio  Frequency  (RF) Controls. The information contained herein is based on data gathered from various users of portable remote control crane systems.  We emphasize that the recommendations contained herein are not intended to supersede the rules or regulations of our customers, or the rules and regulations of any applicable local, state, or federal government organizations.  It must be fully understood that the recommendations contained herein are provided solely for your consideration and possible adoption. TABLE OF CONTENTS SECTION  TITLE                PAGE      1    Preface                     1      2    Operator Safety Basics                 2      2-1    Area Inspection                 2      2-2    Crane Inspection (mechanical & structural)           2      2-3    Operational Safety Check               3      3    Persons Authorized to Operate Remote Controlled cranes         3      4    Training Check List for Operation of Remote Controlled cranes       3      5    Operating Area for Remote Controlled Cranes           4      6    The Hand-held Portable Remote Controller             4      7    Operating the Remote Controlled Crane             5      8    Boarding the Remote Controlled Crane             6      9    On Board the Remote Controlled Crane             6    10    Remote Controlled Crane under Repair             7    11    The Condition of the Remote Controlled Crane           8 1.  PREFACE. 1-1.  Electric Overhead Traveling (EOT) Cranes typically operate in three motions.  They are large, bulky  pieces  of  equipment  that  handle  heavy  loads  efficiently  at  comparatively  high  speeds.  Frequently, they are operated in restricted areas where workmen are engaged in various tasks on the floor below.  Under these conditions crane operators using Portable Remote Control (PRC) must take great care, and workmen must be constantly on the alert if accidents are to be avoided. 1-2.  The following guidelines have been carefully assembled and are promoted to indicate just how important  your  careful  and  thoughtful  actions  are  in  helping  to  protect  you  and  your  fellow workers from harm, and also to prevent equipment damage. 1-3.  These  guidelines  cover  cranes  when  they  are  operational  in  Portable  Remote  Control  (PRC) mode by Radio Frequency.  If a crane is operated from cab or pendant control, the PRC system’s controller(s) should be completely isolated by removing the battery and held under lock and key. 1-4.  A routine pre-shift inspection of the crane takes a lot less time than repairing a crane suffering from a  major problem.  In addition,  such pre-shift  inspections are to be considered as ‘safety basics’ which are an important part of a crane operator’s duties.
 Cranesafety – page 2    03/2007, CATTRON-THEIMEG™ 2. OPERATOR SAFETY BASICS.  Before starting your shift as the crane operator, you should make sure the crane has a current inspection certificate and that qualified personnel have carried out the following inspections and checks.  If any item below does not pass inspection, you should notify your supervisor immediately.  In many cases, the problem will need to be fixed before you are allowed to operate the crane.  In addition, did you realize that the person now reading these instructions is primarily responsible for his or her own health and safety? 2-1   Area Inspection.  • Take a good look around the work area for any obstructions. • Check that the rails are intact and not bent or damaged.  • Make sure there are no oil or brake fluid leaks on the area below where the crane travels. • Make sure rail stops are present, physically secure, and free of damage at the end of all crane rails.  • Check that walkways are sturdy and have handrails.  Ladders are not to be loose and all rungs are to be in place. 2-2.  Crane Inspection (mechanical & structural). • Make sure all moving machinery has protective guards installed over moving parts. • Make sure all bridge and trolley rail stops are welded or bolted in position with no evidence of damage from bridge or trolley impact.  • Check for proper fluid levels and make sure all grease fittings are lubricated to manufacturer recommendations.  • Check for broken welds and cracks in the bridge structure.  • Check for wheel damage, broken welds on the frame, and drum damage.  • Check the wheels for flange wear, cracks, holes, or visible signs of bearing damage. • Make sure wire rope drums show proper wire rope lay; for example, each wire rope must lay in its own groove.  This does not mean in the non-grooved area in the center of the drum.  • Make sure wire rope size is correct for the sheaves.  Look for either oversized or undersized rope that will not lay in the sheaves correctly.  Make sure the sheaves show no evidence of rope corrugation and have the proper wall thickness.  • Look for any type of bluing on the brake drums which indicates excessive heat.  Make sure there are no protruding rivets from the brake shoes.  Examine the shoes for glazing.  • Look for carbon dust around the inspection covers of electric motors.  Smell for any type of burning smells.  Check for any type of burning on electrical covers.  Make sure all protective covers are installed. • Check  the  festoon  system  for  proper  connections  and  inspect  all  hooks  connecting  the festoon to the holding wire. • Load bearing parts such as blocks and hooks shall have no signs of damage and be in perfect working order.
 03/2007, CATTRON-THEIMEG™   Cranesafety – page 3 2-3.  Operational Safety Check.  As a crane operator, you should satisfy yourself of the following.  If  any  item  below  does  not  meet  the  checklist  criteria,  you  shall  immediately  notify  your supervisor.  In many cases, the problem will need to be fixed before you are allowed to operate the crane.  Remember that the person now reading these instructions is primarily responsible for his or her own health and safety! • Horns, buzzers and all other warning devices shall be in working order. • All controls shall be in good working order. • STOP Buttons (when equipped) shall be in working order.  • The load brakes shall hold the load safely at all times.  The only way to ensure this is through a load test and inspection. • The ‘raise’ and ‘lower’ limit switches shall work correctly to help prevent two-blocking and accidental floor contact.  3.  PERSONS AUTHORIZED TO OPERATE REMOTE CONTROLLED CRANES. • Only  properly  trained  employees  who  have  been  designated  by  management  shall  be permitted to operate the crane. • Both the operator and management shall insure the correct controller to operate the crane is selected and that any spare equipment capable of controlling the crane is completely isolated and held under lock and key. • The  crane  shall  not  be  operated  by  personnel  who  cannot  read  and  understand  the  signs, notices and operating instructions. • The crane shall not be operated by personnel with seriously defective eyesight or hearing, personnel under  the influence of  drugs or alcohol  that  will impair  judgment, or  personnel who may be suffering from a disease which may cause physical failure.   4.  TRAINING CHECKLIST FOR OPERATORS OF REMOTE CONTROLLED CRANES. As a minimum, Portable Remote Control Operators shall: • have knowledge of hazards inherent to crane operation. • have knowledge of safety guidelines for portable remote controlled cranes. • have the ability to judge distance to stationary objects. • have knowledge of the portable remote control system controller’s operation. • have performed limit switch test procedure before operating the crane. • have performed hoist, trolley and bridge brake test procedure before operating the crane. • have instructions as to plugging of crane motions when and where authorized. • observe signal lights on crane. • avoid striking any obstructions. • check for proper clearance of lifts or hooks before moving bridge or trolley. • properly store the portable remote controller when not in use. • know how to properly transfer the portable remote controller to another person. • report unsafe or unusual operating conditions. • use caution in approaching bridge or trolley end-stops. • know the crane’s capacity. • keep body clear of lifts, avoiding ‘pinch’ points. • Inspect cables and hooks.
 Cranesafety – page 4    03/2007, CATTRON-THEIMEG™ 5. THE OPERATING AREA FOR THE REMOTE CONTROLLED CRANE. • Unobstructed aisles between equipment, stock,  etc. shall be maintained for the PRC crane operator's movement.  These aisles should be a minimum of 3 feet wide (1m) or per local regulations. • PRC crane operators shall always position themselves in a safe location with the best view of the crane they are controlling and never operate the crane blindly.  They shall always keep the crane and load in sight, staying as close as practical to the crane load while maintaining a safe harms-way distance.  Operators shall never position themselves or others underneath the load or in a ‘pinch’ point.  6.  THE HAND-HELD PORTABLE REMOTE CONTROLLER. • Typically,  the  portable  remote  controller  incorporates  a  Push-To-Operate  (PTO)  bar  or START button, and its motion switches are spring return to OFF.  The PTO bar acts as a guard  for  these  switches  to  prevent  movement  of  the  crane  if  one  of  the  switches  is accidentally bumped.  These switches and the PTO bar must never be mechanically blocked in any ‘ON’ position. • Using the power ON/OFF switch(es), the portable remote controller shall be switched ‘OFF’ when not in use.  When the controller is equipped with a STOP button, it shall be set to the ‘STOP’ position before switching off power to the controller.  In addition, if equipped with a key, the key should be removed after use and kept in a secure location.  • A prescribed, controlled, storage space shall be provided for portable remote controllers.  All controllers  shall  have their  batteries  removed  and  be  placed there  when  not  in  use.    This precaution  is  intended  to  prevent  unauthorized  personnel  from  operating  the  remote controlled crane. • When an operator is putting on or taking off the controller by means of its belt loop strap, carrying harness, or shoulder strap, the controller shall be switched OFF beforehand, using the appropriate ON/OFF switch(es).  When the controller is equipped with a STOP button, it shall be set to the ‘STOP’ position before switching off power to the controller. • The portable remote controller shall always be switched ‘OFF’ when not in use and, when practical, stored under lock and key.
 03/2007, CATTRON-THEIMEG™   Cranesafety – page 5 7.  OPERATING THE REMOTE CONTROLLED CRANE. • All  crane  limit  switches  shall  be  checked  at  the  beginning  of  each  turn  or  when  a  new operator takes control  of  the crane.    While  checking  the limit switches, the  hoist  shall be centered over an area free of personnel and equipment so that if the limit switches fail, and the hook and block assembly falls, no one will be injured and no equipment will be damaged. • The limit switches shall never be used as a regular stopping devices.  They are intended to be protective devices only. • The bridge and trolley brakes shall be tested at the beginning of each turn or when a new operator takes control of the crane.  They should be tested with the bridge and trolley at low speed. • When lifting maximum or near maximum loads, the operator shall test the hoist brakes by raising the load a few inches from the floor.  If hoist brakes do not hold, the load shall be immediately lowered to the floor and a report made to the supervisor. • Do not make lifts in excess of the rated capacity of the crane.  • When making lifts, the bridge and trolley shall be centered directly over the load to prevent load swinging when the load is raised. • Side  pulls  shall  be  made  only  with  the  permission  of,  and  under  direct  supervision  of management.  When such a lift is being made, operators shall not position themselves in the line  or  path  of  travel  of  the  load,  but  shall  operate  the  crane  from  a  position  to  the  side opposite to the path of travel. • When raising or lowering a load, proceed slowly and make certain the load is under control.  Tag lines shall be used for handling lengths or bulky loads.  Take the slack out of the chains or slings gradually.  Make sure all personnel are clear before making a lift. • PRC  crane  operators  shall  keep  all  parts  of  their  bodies  away  from  the  load  and  never position themselves under the load. • Do not make a lift or move the crane if anyone is in a position to be injured. • If a PRC crane operator is being helped, he or she shall not move the crane until he or she receives an ‘all clear’ signal from the helper(s). • Loads shall not be carried over workers' heads. • If anyone is in the path of travel, the portable remote control crane operator shall stop and clear the area before proceeding. • Bumping into runway stops or into other cranes on the same runway is prohibited. • When moving the crane, the PRC crane operator shall make sure the hook block, attachment and/or cables will not fall on nearby equipment. • The PRC crane operator shall not drag slings, chains, etc. along the floor.  These could snag on something on the floor, causing the cables to break and strike the operator or a fellow worker. • If  gloves  are  not  required  for  safety  reasons,  they  shall  not  be  used  when  operating  the portable remote controller.
 Cranesafety – page 6    03/2007, CATTRON-THEIMEG™ 7.  OPERATING THE REMOTE CONTROLLED CRANE, continued. • All  loose  material  or  parts  shall  be  removed  from  the  load  before  starting  the  lift.    Such material can fall and injure people below. • The PRC crane operator shall hoist lifts high enough to clear all apparatus and workers below the crane. • Plugging shall not be used as a regular means of stopping the crane and should be used for emergency stops only.  If approved, plugging should only be performed as dictated by plant operating procedures.   • If PRC crane operators are asked to do something they believe unsafe, they shall call their supervisors for advice. • PRC  crane  operators  shall  never  permit  anyone  to  ride  on  the  load  or  hook  except  when authorized by their supervisor. • When another crane on the same runway is stationary with or without a load, the PRC crane operator shall maintain a safe distance between the crane being operated and the stationary crane.  In a power outage, the PRC crane operator shall set the ON/OFF switch(es) on the controller to ‘OFF’, keeping them in the OFF position until power is restored.   • If the PRC crane fails to respond correctly, the operator shall stop operation immediately by setting the ON/OFF switch(es) on the controller to ‘OFF’. When the controller is equipped with a STOP button, this shall be set to the ‘STOP’ position before switching off power to the controller.  The fault condition shall be reported immediately to a supervisor. • Outside cranes subject to movement by winds, storms, etc. shall be securely anchored when left unattended.  If the crane is equipped with a bridge parking brake, it shall also be set. 8.  BOARDING THE REMOTE CONTROLLED CRANE (MAINTENANCE CREW). • The PRC crane shall not be boarded without permission of the supervisor in charge of crane operations in the area. • Using the power ON/OFF switch(es), the person boarding the PRC crane shall switch the portable remote controller to ‘OFF’ and take it with him or her on to the crane.  When the controller is equipped with a STOP button, this shall be set to the ‘STOP’ position before switching off power to the controller. • If the boarding party consists of more than one person, one person shall be designated as the leader of the boarding party. • The leader shall board the crane first, open and lock out the main switch (securing it with a padlock), and then signal the other members of the party that it is safe for them to board the crane. 9.  ON BOARD THE REMOTE CONTROLLED CRANE (MAINTENANCE CREW). • Head room is at a minimum in some crane cabs and on some crane walkways.  Caution shall be exercised by all people on board such cranes.  Hard hats shall be worn at all times. • If the repair crew consists of more than one person, one person shall be designated as the crew leader.
 03/2007, CATTRON-THEIMEG™   Cranesafety – page 7 9.  ON BOARD THE REMOTE CONTROLLED CRANE, continued. • Warning signs shall be placed on the floor beneath the crane or suspended from the crane indicating the crane is being serviced. • If  any  work  to  be  done  on  the  crane  is  carried  out  in  locations  unprotected  by  standard handrails,  safety  belts  shall  be  worn  by  all  crew  members  working  in  such  unprotected locations. • All tools and equipment shall be moved onto the crane by the use of hand lines.  All tools and equipment shall be securely attached to hand lines. • If it is necessary to have the control circuits on the crane energized, the repair crew leader shall open all power circuits to the motions before closing the main switch. • If,  during  the  course  of  repairs,  it  becomes  necessary  to  move  the  crane,  it  shall  be  the responsibility  of  the  crew  leader  to  insure  that  all  personnel  located  on,  and  within  the operational area of the crane are in a safe position out of harms-way.  In addition the crew leader shall insure all tools and materials are stowed or tightly restrained before the crane is moved. • When the repair work is completed, the crew leader shall see that all crew members are off of the crane before he or she closes the main switch. • If more that one person is on board the PRC crane, one person shall be made responsible for seeing that all workers are off the crane before the portable remote controller is returned to operational use.  10.  REMOTE CONTROLLED CRANE UNDER REPAIR. • All persons operating other cranes on the same or adjacent runways shall be notified before anyone boards the subject  crane.    Such notification should include  limitations of adjacent crane movement while others are on board. • PRC  cranes  which  have  been  pre-positioned  for  repairs  and  cannot  be  moved  should  be protected against being bumped by other cranes on the runway.  Suitable bumpers adequate for the job should be installed on the exposed sides of the crane under repair and as far away from the crane as possible, with a minimum distance of 20 ft. (approximately. 6.1 m).  The location of these bumpers shall be indicated by red lights so that they are clearly visible to other persons operating cranes traveling on the same runway.  When it is impossible to use bumpers for protection, red lights shall be placed in clear view of other persons operating cranes on the same runway to indicate the restricted travel zone.  It is desirable that such red lights be located a minimum of 20 ft. (approx. 6.1 m) from the crane under repair.   • All operators of cranes on the same runway must be informed of the repair work, thoroughly instructed as to what their conduct should be for the duration of said repairs, and informed when repairs are completed.
 Cranesafety – page 8    03/2007, CATTRON-THEIMEG™ 10.  REMOTE CONTROLLED CRANE UNDER REPAIR, continued. • When there is a runway adjacent to the runway on which the crane is being repaired, and if any hazard  exists  involving repairmen, red  lights shall be placed in clear view of persons traveling on the adjacent runway to indicate the restricted travel zone.  It is desirable that such red lights be located a minimum of 20 ft. (approx. 6.1 m) from the crane under repair.  When it is necessary to operate cranes on adjacent runways, such cranes shall come to a full stop  before  entering  the  restricted  area.    Cranes  traveling  on  adjacent  runways  may  only proceed  through  the  restricted  area  when  permission has  been  received  from  a  signalman posted for this purpose. • Access of persons  to  and  from the  crane  being  repaired  shall  be  under  the  control  of the repair crew leader. • The floor area below the point where crane repairs are being made shall be roped off and posted with danger signs. • Handling of all small tools and materials, etc. from ground level to workers above shall be accomplished through the use of hand lines.  Tools, materials, etc. shall not be tossed from the crane to the ground level and vice versa. • If crane repairs make it necessary for crew members to work on areas of the crane other than those protected by standard handrails, such crew members shall wear approved safety belts. • If it is necessary to move the crane to check the performance of operation, the crew leader shall designate who remains on the crane.  The crew leader shall insure that all personnel located  on,  and  within  the  operational  area  of  the  crane  are  physically  located  in  a  safe position out of harms-way.  In addition the crew leader shall insure all tools and materials are stowed  or  tightly  restrained  before  the  main  switch  is  closed  and  the  crane  is  put  into operation. • Upon completion of repairs, it is the crew leader's duty to personally insure that each person has left the crane and is clear before he or she removes the lock above the main switch and the crane is put back in operation.  11.  THE CONDITION OF THE REMOTE CONTROLLED CRANE.  It is recommended that a written report be sent to your supervisor whenever you detect any condition that makes the crane unsafe.  Many plants supply printed forms for this purpose.  The PRC crane operator shall fill out these  forms  and  turn  them  in  at  the  end  of  each  shift.    Certain  faults  which  the  PRC  crane operator may detect will be so critical that the crane must be shut down at once and not operated until the fault is corrected.  Typical check list items may include some or all of the following: • Condition of hoisting cable, drum, and hook blocks (broken strands, clipped sheave wheels, etc.). • Condition of brakes (hoist, trolley and bridge). • Oil or brake fluid leaks on the runway area. • Alignment of bridge (screeching or squealing wheels indicate that bridge is out of line). • Condition of bridge structure (broken welds, cracks and distortion). • Broken, cracked or chipped rails on bridge or runway.
 03/2007, CATTRON-THEIMEG™   Cranesafety – page 9 11.  THE CONDITION OF THE REMOTE CONTROLLED CRANE, continued. • Condition  and  security  of  trolley  and  bridge  rail  end-stops  (missing  or  damaged  from impact). • Condition of all limit switches. • Conditions of controls (electrical or mechanical defects that may lead to faulty operation). • Condition of electric motors (carbon dust around inspection covers indicate worn brushes).  • Condition of gears (grinding or squealing may mean a lack of lubrication or foreign materials in gear teeth). • Frequent overload relay tripping of power circuits. • Mechanical parts loosened by vibration (loose rivets, covers, etc.). • Wheel condition (flange wear, cracks, holes, or visible signs of bearing damage). • Bumpy riding (worn wheels). • Worn collector shoes or bars. • Burned out, broken, or inoperable warning or signal lights. • Unintended  stopping  or  starting  of  any  crane  motion,  warning  device,  light  or  auxiliary function. • Condition of walkways and ladders (missing or loose handrails, ladder rungs, etc.)  Portable Remote-controlled Crane operators shall not attempt to make any repairs by themselves. The fault condition(s) shall be reported to a supervisor to enable repairs to be carried out by suitably qualified personnel.  END   Internet Address for All CATTRON-THEIMEG™ Companies: www.cattron-theimeg.com
 Cranesafety – page 10    03/2007, CATTRON-THEIMEG™  This page intentionally left blank.
 03/2007, CATTRON-THEIMEG™   Locosafety – page 1 RECOMMENDED SAFETY RULES FOR PORTABLE RADIO REMOTE CONTROLLED (PRRC) LOCOMOTIVES The information contained herein is based on data gathered from various users of portable radio remote control locomotive systems.  We  emphasize  that  the recommendations  contained herein are not intended to supersede the rules or regulations of our customers, or the rules and regulations of any applicable local, state, or federal government organizations.  It must be fully understood that the recommendations contained herein are provided solely for your consideration and possible adoption.  TABLE OF CONTENTS SECTION  TITLE                    PAGE      1    Preface                        1      2    Operator Safety Basics                    2      2-1    Area Inspection                      2      2-2    Locomotive & Railcar Inspection (mechanical & structural)           2      2-3    Operational Safety Check                    2      3    Persons Authorized to Operate Remote Controlled Locomotives          2      4    Training Checklist for Operation of Remote Controlled Locomotives      3      5    Operating Area for Remote Controlled Locomotives             3      6    Pre-departure Checks under Manual Control                        3      7    The Portable Radio Remote Controller                4      8    Transferring the Locomotive to Radio Remote Control            5      9    Pre-departure Checks under Radio Remote Control              5    10    Operating the Remote Controlled Locomotive              6    11    Boarding the Remote Controlled Locomotive               7    12    On Board the Remote Controlled Locomotive              8    13    Remote Controlled Locomotive under Repair                     8    14    The Condition of the Remote Controlled Locomotive          10  1. PREFACE. 1-1.  Locomotives operate in  two  motions.   They are large,  bulky pieces  of  equipment that  handle heavy  loads  efficiently  at  comparatively  high  speeds.    Quite  frequently  they  are  operated  in restricted areas where workmen are engaged in various tasks or there is pedestrian or vehicular traffic.  Under these conditions locomotive operators using Portable Radio Remote Control must take great care, and workmen must be constantly on the alert if accidents are to be avoided. 1-2.  The following guidelines have been carefully assembled and are promoted to indicate just how important  your  careful  and  thoughtful  actions  are  in  helping  to  protect  you  and  your  fellow workers from harm, and also to prevent equipment damage. 1-3. These  guidelines  cover  Locomotives  when  they  are  operational  in  Portable  Radio  Remote Control  (PRRC)  mode.  If  a  locomotive  is  operated  from  cab  control,  the  PRRC  system’s controller(s) should be completely isolated by removing the battery and stored under lock and key. 1-4. A routine pre-shift inspection of the locomotive takes a lot less time than repairing a locomotive suffering from a major problem.  In addition, such pre-shift inspections are to be considered as ‘safety basics’ which are an important part of a locomotive operator’s duties.
 Locosafety – page 2    03/2007, CATTRON-THEIMEG™ 2.  OPERATOR SAFETY BASICS.  Before starting your shift as the locomotive operator,  you should make sure the locomotive has a current inspection certificate and that qualified personnel have  carried  out  the  following  inspections  and  checks.    If  any  item  below  does  not  pass inspection,  you should  notify  your supervisor immediately.   In  many  cases,  the problem will need to be fixed before you are allowed to operate the locomotive.  In addition, did you realize that the person now reading these instructions is primarily responsible for his or her own health and safety? 2-1  Area Inspection.  • Take a good look around the work area for any obstructions. • Check that the rails are intact and not bent or damaged.  • Make sure there are no fresh oil or fluid leaks on the track bed below where the locomotive is standing. • When installed, insure rail stops are physically secure and free of damage at the end of the rail track.  2-2.  Locomotive and Rail Car Inspection (mechanical & structural). • Check for proper fluid levels and make sure all grease fittings are lubricated to manufacturer recommendations.  • Check the locomotive and rail car wheels for flange wear, cracks, holes, or visible signs of bearing damage. • Check all locomotive and rail car hoses and couplings for wear and physical damage.  2-3.  Operational  Safety  Check.    As  a  locomotive  operator,  you  should  satisfy  yourself  of  the following.  If any item below does not meet the checklist criteria, you shall immediately notify your supervisor.  In many cases, the problem will need to be fixed before you are allowed to operate the locomotive.  Remember that the person now reading these instructions is primarily responsible for his or her own health and safety! • Horn, headlight, bell, and all other warning devices shall be in working order. • All locomotive manual (cab) controls shall be in good working order. • STOP Buttons (when equipped) shall be in working order.  • The  locomotive  and  railcar  braking  systems  (including  the  application  of  sand  when equipped) are fully operational. The only way to ensure this is by testing under ‘MANUAL’ (cab) control.  3. PERSONS AUTHORIZED TO OPERATE REMOTE CONTROL LOCOMOTIVES. • Only  properly  trained  employees  who  have  been  designated  by  management  shall  be permitted to operate the locomotive(s). • The locomotive shall not be operated by personnel who cannot read and understand the signs, notices and operating instructions. • The  locomotive  shall  not  be  operated  by  a  person  with  seriously  defective  eyesight  or hearing,  personnel  under  the  influence  of  drugs  or  alcohol  that  will  impair  judgment,  or personnel who may be suffering from a disease which may cause physical failure.
 03/2007, CATTRON-THEIMEG™   Locosafety – page 3 4.  TRAINING  CHECKLIST  FOR  OPERATORS  OF  REMOTE  CONTROLLED LOCOMOTIVES.   As a minimum, Locomotive Operators shall: • have knowledge of hazards inherent to locomotive operation  • have knowledge of safety rules for remote controlled locomotives  • have the ability to judge distance to stationary objects  • have  knowledge  of  the  PRRC  system  controller’s  operation  –  see  customized  operational description provided with the controller  • inspect all aspects of the locomotive in manual operation before commencing remote control operation • have performed pre-departure brake test procedures in manual operation before commencing remote control operation   • know how to transfer the locomotive from ‘MANUAL’ to ‘REMOTE’ Control • be familiar with the procedure for testing all operational features • observe all signal lights and other railroad signaling devices   • avoid striking any obstructions  • check for proper clearance before entering buildings, etc.  • properly store the portable radio remote controller when not in use  • know how to properly transfer the portable radio remote controller to another person • report unsafe or unusual operating conditions • use caution in approaching all crossings • keep body clear of the rail track and avoid ‘pinch’ points  5.  THE OPERATING AREA FOR THE REMOTE CONTROLLED LOCOMOTIVE. • PRRC operators shall always position themselves in a safe location with the best view of the train they are controlling and never operate the locomotive blindly.  • Operators shall always keep the train and locomotive in sight, staying as close as practical to the locomotive while maintaining a safe harms-way distance. • Operators shall follow their Employer’s Safety Rules, Procedures, and Directives in regard to riding on, walking in front of, and boarding/de-boarding at the leading edge of the train in respect to its direction of travel.  • Operators shall never position themselves or others in a ‘pinch’ point between rail cars, other locomotives, or track side structures. • Operators shall never position themselves between the rails of tracks. 6.  PRE-DEPARTURE CHECKS UNDER MANUAL CONTROL.  • When installed, insure the STOP buttons located on the sides of the locomotive are pulled ‘OUT’ immediately before boarding the locomotive. • When installed  to the locomotive, insure:  (1) Remote Control Disconnect Switch  is set  to ‘OFF’,  (2)  MANUAL/REMOTE  Transfer  Switch  is  set  to  ‘MANUAL’,  and  (3) MANUAL/REMOTE Air Valves are in the ‘MANUAL’ (down) position.
 Locosafety – page 4    03/2007, CATTRON-THEIMEG™ 6.  PRE-DEPARTURE CHECKS UNDER MANUAL CONTROL, continued. • Perform  all  locomotive  pre-departure  tests  according  to  the  locomotive  manufacturer's operation manual.  Do not proceed unless the locomotive is operating satisfactorily according to the manufacturer's instructions.  • All  non-motion  control  functions  (Horn,  headlight,  bell,  sanders,  uncouple,  etc.)  shall  be checked  at  the  beginning  of  each  turn  or  when  a  new  operator  takes  control  of  the locomotive. • All braking functions shall be checked independently to insure the locomotive is responding correctly  to  all  brake  applications  and  release  commands.    Observe  gages  in  the  cab  for proper readings and verify the brake mechanisms/cylinders operate properly. • Test train brakes (if equipped). 7.  THE PORTABLE RADIO REMOTE CONTROLLER. • Typically, the portable  radio  remote  controller incorporates a Push-To-Operate (PTO) bar and its THROTTLE switch will spring return to IDLE.  The PTO bar acts as a guard for the throttle switch to prevent movement of the locomotive if the switch is accidentally bumped.  The THROTTLE switch and the PTO bar must never be mechanically blocked in any ‘ON’ position. • When the portable radio remote controller incorporates a ‘Vigilance’ system in place of the Push-To-Operate (PTO) bar, the designated VIGILANCE pushbutton, bar switch, or toggle switch  may need to  be momentarily depressed to  initiate  a  motion  control  function.  The designated  VIGILANCE  pushbutton,  bar  switch,  or  toggle  switch  must  never  be mechanically blocked in the ‘ON’ position. • Direction  and  brake  levers  normally  have  no  spring  return  and  will  stay  where  they  are placed.  Although the PTO Bar is not normally required for brake apply commands, it must be depressed to release the independent brakes and, when equipped, the train brakes. • Using the power ON/OFF switch(es), the portable radio remote controller shall be switched ‘OFF’ when not in use.  When the controller is equipped with a STOP button, it shall be set to the ‘STOP’ position before switching off power to the controller.  In addition, if equipped with a key, the key should be removed after use and kept in a secure location.  • To  prevent  unauthorized  personnel  from  operating  the  remote  controlled  locomotive,  a prescribed, controlled, storage space shall be provided for portable radio remote controllers.  All controllers shall have their batteries removed and be stored there when not in use. • When an operator is putting on or taking off the controller by means of its belt loop strap, carrying harness, or shoulder strap, the controller shall be switched OFF beforehand, using the appropriate ON/OFF switch(es).  When the controller is equipped with a STOP button, it shall be set to the ‘STOP’ position before switching off power to the controller. • The portable radio remote controller shall always be switched ‘OFF’ when not in use and, when practical, stored under lock and key.
 03/2007, CATTRON-THEIMEG™   Locosafety – page 5 8.  TRANSFERRING THE LOCOMOTIVE TO RADIO REMOTE CONTROL. • Both  the  operator  and  management  shall  insure  the  correct  controller  to  operate  the locomotive is identified and selected. • Both  the  operator  and  management  shall  insure  that  any  spare  equipment  capable  of locomotive control is completely isolated and stored under lock and key. • Immediately  before  transferring  the  locomotive  from  ‘MANUAL’  to  ‘REMOTE’  control, insure the locomotive cab controls are set as follows:  Throttle to ‘IDLE’  Reverser to ‘NEUTRAL’ with handle removed  Independent Brake Lever to ‘RUN’ position and handle removed  Automatic Brake Lever to ‘LAP’ position and handle removed  Double Heading Cock to trailing position (MU - operation)  MANUAL/REMOTE Air Valves to ‘REMOTE’ (up) position  Remote Control Disconnect Switch to ‘ON’ position  MANUAL/REMOTE Transfer Switch to ‘REMOTE’ position 9.  PRE-DEPARTURE CHECKS UNDER RADIO REMOTE CONTROL.  Following  is a typical  pre-departure  checkout  procedure  based  upon  a  typical  configuration.    Refer  to  the information supplied with the equipment for the specific checkout procedure.     • With  the  remote  controller  set  to  ‘OFF’,  check  brake  cylinder  for  air  pressure.    The  red external locomotive lights (if equipped) should illuminate, indicating independent brakes are applied. • Set remote controller to ‘ON’.  When applicable, check the PRRC system display(s) for any fault/alarm  conditions  and  correct  the  same  before  operating  the  appropriate ALARM/SYSTEM RESET switch.   • With Push to Operate  (PTO) Bar depressed,  move the  independent brake lever on remote controller  to  release  (REL).    Independent  brakes  should  release  and  the  red  external locomotive lights should extinguish. • Move independent brake lever on remote controller to an ‘apply’ position (SA = Slow Apply, QA = Quick Apply). Independent brakes should apply with corresponding external red lights illuminated. • Move independent brake lever on remote controller to ‘EMG’ (emergency) position. When   equipped, train brakes should apply along with independent brakes.  When equipped, sand should also be applied. • Move direction lever on  remote controller  to ‘FORWARD’.   Forward direction  should be selected, as indicated by the clear external locomotive lights (if equipped) illuminating. • Move  direction  lever  on  remote  controller  to  ‘REVERSE’.    Reverse  direction  should  be selected as indicated by the amber external locomotive lights (if equipped) illuminating and the clear lights extinguishing.
 Locosafety – page 6    03/2007, CATTRON-THEIMEG™ 9.  PRE-DEPARTURE CHECKS UNDER RADIO REMOTE CONTROL, continued. • Move  direction  lever  on  remote  controller  to  center  ‘NEUTRAL’  position.  ‘NEUTRAL’ should be selected as indicated by both amber and clear lights extinguished. • With independent brakes released (PTO must be depressed and maintained) and a direction selected, advance THROTTLE lever on remote controller to first ‘step’.  The green external locomotive lights (if equipped) should illuminate and the locomotive should move. • Release Push to Operate (PTO) Bar on remote controller.  Throttle should return to ‘idle’ and independent  brakes  should  apply, stopping  the  locomotive  (red  external  locomotive  lights illuminated and green lights extinguished). • With independent brakes released (PTO must be depressed and maintained) and a direction selected, advance THROTTLE lever on remote controller to first ‘step’.  The green external locomotive lights should illuminate and the locomotive should move. • Tilt remote controller 60° or more.  Throttle should return to ‘idle’ and independent brakes should apply, stopping the locomotive (red external locomotive lights illuminated and green lights  extinguished).  Return  the  remote  controller  to  the  upright  position  and  independent brakes should release (red external lights extinguished). • With independent brakes released (PTO must be depressed and maintained) and a direction selected, advance THROTTLE lever on remote controller to first ‘step’.  The green external locomotive lights should illuminate and the locomotive should move. • Set  remote  controller  to  ‘OFF’.  Throttle  should  return  to  ‘idle’  and  independent  brakes should apply, stopping the locomotive (red external locomotive lights illuminated and green lights extinguished).  • De-board  the  locomotive  and  assume  an  operating  position  on  the  ground  next  to  the locomotive.  Set remote controller to ‘ON’.  With independent brakes released (PTO must be depressed and maintained) and a direction selected, advance THROTTLE lever on remote controller  to  first  ‘step’.    The  green  external  locomotive  lights  should  illuminate  and  the locomotive should move. Immediately after the locomotive starts to move, push in a STOP switch (if equipped) on side of locomotive.  The locomotive  should stop  and independent brakes should apply.   Repeat this step with all STOP switches.  STOP switches should be checked daily. If the above checks have been successfully completed, the locomotive is now ready for remote control operation. 10.  OPERATING THE REMOTE CONTROLLED LOCOMOTIVE. • When ready to move the locomotive for the first time, proceed slowly and make certain the load is under control.   • Take the slack out of the couplers gradually and make sure hands and other objects are clear before making command. • Keep all parts of the body away from the rolling stock.   • Do not walk on the tracks between the rails.  • Do not move the locomotive or train if anyone is in a position to be injured. • If anyone is in the path of travel, stop and sound the horn before proceeding.
 03/2007, CATTRON-THEIMEG™   Locosafety – page 7 10.  OPERATING THE REMOTE CONTROLLED LOCOMOTIVE, continued. • If  gloves  are  not  required  for  safety  reasons,  they  shall  not  be  used  when  operating  the portable remote controller. • PRRC operators shall not use a STOP switch, VIGILANCE switch or Push-to-Operate bar as a utility stopping device. • If  PRRC  locomotive  operators  are  asked  to  do  something  they  believe  unsafe,  they  shall contact their supervisor for advice. • PRRC locomotive operators shall never permit anyone to ride in the locomotive cab except when authorized by their supervisor. • Heavy bumping of cars or rail stops is prohibited. • When leaving the locomotive for any reason, set the locomotive throttle to ‘IDLE’, apply the brakes, and set the ON/OFF switch(es) on the controller to ‘OFF’.  When the controller is equipped with a STOP button, this shall be set to the ‘STOP’ position before switching off power to the controller. • If  the  locomotive  fails  to  respond  correctly  under  remote  control,  the  operator  shall  stop operation immediately by setting the ON/OFF switch(es) on the controller to ‘OFF’. When the controller is equipped with a STOP button, this shall be set to the ‘STOP’ position before switching off power to the controller.  The fault condition shall be reported immediately to a supervisor. • Do not allow any unauthorized person to operate or assist with the operation while in Radio Remote Control. • Do not operate the Remote Controller from a distance where the locomotive, railcars, rail-track, and all surrounding objects are not visible. • Under no circumstances should an operator override any of the safety features built into the  PRRC system or the locomotive. 11.  BOARDING THE REMOTE CONTROLLED LOCOMOTIVE (MAINTENANCE CREW). • The PRRC locomotive shall not be boarded without permission of the supervisor in charge of railroad operations in the area. • Using the power ON/OFF switch(es), the person boarding the PRRC locomotive shall switch the  portable  radio  remote  controller  to  ‘OFF’  and  take  it  with  him  or  her  on  to  the locomotive.  When the controller is equipped with a STOP button, this shall be set to the ‘STOP’ position before switching off power to the controller. • If the boarding party consists of more than one person, one person shall be designated as the leader of the boarding party. • The leader shall board the locomotive first, secure the throttle and brakes, and then signal the other members of the party that it is safe for them to board.
 Locosafety – page 8    03/2007, CATTRON-THEIMEG™ 12.  ON BOARD THE REMOTE CONTROLLED LOCOMOTIVE (MAINTENANCE CREW). • Headroom is at a minimum in some locomotive cabs and on some engine walkways.  Caution shall be exercised by all people on board such locomotives.  Hard hats shall be worn at all times. • If the maintenance crew consists of more than one person, one person shall be designated as the crew leader. • The leader shall mark all locomotives that have been pre-positioned for maintenance with a blue flag.  The locomotive shall not be coupled to, or moved in any manner, while the blue flag is in position. The leader is solely responsible for removing the blue flag before moving the locomotive, or when maintenance has been completed. • Warning signs shall be placed on the front, rear, and both sides of the locomotive to indicate that maintenance is being carried out. • If it is necessary to have the control circuits on the locomotive energized, the leader shall insure that traction power is disabled (i.e. generator field switch set to the ‘OFF’ position). • If, during the course of maintenance, it becomes necessary to move the locomotive, it shall be the responsibility of the crew leader to insure that all personnel located on, and inside the locomotive are in a safe position out of harms-way.  In addition the crew leader shall insure all tools and materials are stowed or tightly restrained, all doors are secured, and the blue flag is removed before moving the locomotive. • When the maintenance work is completed, the leader shall see that all personnel are off the locomotive before he or she re-enables traction power.  • If more that one person is on board the locomotive, one person shall be made responsible for seeing that all personnel are off the locomotive before the portable radio remote controller is returned to operational use. 13.  REMOTE CONTROLLED LOCOMOTIVE UNDER REPAIR. • All  persons  operating  other  locomotives  on  the  same  or  adjacent  tracks  shall  be  notified before anyone boards the subject locomotive.  Such notification should include limitations of adjacent locomotive movement while others are on board. • If it is necessary to have the control circuits on the locomotive energized, the leader shall insure that traction power is disabled (i.e. generator field switch set to the ‘OFF’ position). • The leader shall mark all locomotives that have been pre-positioned for repairs, and cannot be moved during repairs, with a blue flag.  The locomotive shall not be coupled to, or moved in  any  manner,  while  the  blue  flag  is  in  position.    The  leader  is  solely  responsible  for removing the blue flag when repairs have been completed. • Locomotives that have been pre-positioned for repairs, and cannot be moved during repairs, shall be protected against being bumped by other locomotives on the track.  Suitable derailers adequate for the job should be installed on both ends of the locomotive under repair and as far away from the locomotive as possible with a minimum distance of 100 feet.  The location of these derailers shall  be indicated by red lights placed so that they are clearly visible to other persons operating locomotives traveling on the same or adjacent tracks.
 03/2007, CATTRON-THEIMEG™   Locosafety – page 9 13.  REMOTE CONTROLLED LOCOMOTIVE UNDER REPAIR, continued. • When it is impossible to use derailers for protection, red lights shall be placed in clear view of  other  persons  operating  locomotives  on  the  same  or  adjacent  tracks  to  indicate  the restricted travel zone.  It is desirable that such red lights be located a minimum of 100 feet (approx. 30.5 m) from the locomotive under repair. • All operators of locomotives on the same or adjacent tracks must be informed of the repair work,  thoroughly  instructed  as  to  what  their  conduct  should  be  for  the  duration  of  said repairs, and informed when repairs are completed. • When there is a track adjacent to that of the locomotive being repaired, and if any hazard exists involving repairmen, red lights shall be placed in clear view of persons traveling on the adjacent tracks to indicate the restricted travel zone.  It is desirable that such red lights be located a minimum of 100 ft. (approx. 30.5 m) from the locomotive under repair.     • When  it  is  necessary  to  continue  operation  of  locomotives  on  adjacent  tracks,  such locomotives shall come to a full stop before entering the restricted area.  Locomotives on adjacent  tracks  may  only  proceed  through  the  restricted  area  when  permission  has  been received from a signalman posted for this purpose. • Access of persons to and from the locomotive being repaired should be under the control of the repair crew leader. • Warning signs shall be placed on the front, rear, and both sides of the locomotive to indicate that repairs are being carried out. • Handling of all small tools and materials, etc. from ground level to workers above shall be accomplished safely.  Tools, materials, etc. shall not be tossed from the locomotive to the ground level and vice versa. • If it is necessary to move the locomotive to check the performance of operation, the crew leader shall designate who remains on the locomotive.  The crew leader shall insure that all personnel located on, and inside the locomotive are physically located in a safe position out of harms-way.  In addition the crew leader shall insure all tools and materials are stowed or tightly restrained and that all doors are secured before the locomotive is moved. • When the maintenance work is completed, the leader shall see that all personnel are off the locomotive before he or she re-enables traction power.
 Locosafety – page 10    03/2007, CATTRON-THEIMEG™ 14.  THE  CONDITION  OF  THE  REMOTE  CONTROLLED  LOCOMOTIVE.      It  is recommended that a written report be sent to your supervisor whenever you detect any condition that makes the locomotive unsafe.  Many plants supply printed forms for this purpose.  The radio control locomotive operator should fill out these forms and turn them in at the end of each shift.  Certain faults which the radio control locomotive operator may detect will be so critical that the locomotive  must be  shut  down at  once and  not operated  until  the fault  is  corrected.   Typical check list items may include some or all of the following: • Condition of engine, brakes, and auxiliary functions (i.e., headlight, horn). • Fresh oil or fluid leaks on the track bed below where the locomotive is standing. • Broken, cracked or chipped rails. • Condition of controls (electrical or mechanical defects that may lead to faulty operation). • Frequent overload relay tripping of power circuits. • Mechanical parts loosened by vibration (loose rivets, covers, etc.). • Wheel condition (flange wear, cracks, holes, or visible signs of bearing damage). • Insufficient main reservoir air pressure or a bad compressor. • Condition of hoses and couplings. • Burned out, broken, or inoperable warning or signal lights. • Unintended stopping or starting of any locomotive motion, warning device, light or auxiliary function.  Portable  Remote-controlled  Locomotive  operators  shall  not  attempt  to  make  any  repairs  by themselves.  The fault condition(s) shall be reported to a supervisor to enable repairs to be carried out by suitably qualified personnel.     END   Internet Address for All CATTRON-THEIMEG™ Companies: www.cattron-theimeg.com
    United States Cattron-Theimeg Inc. 58 West Shenango Street Sharpsville, PA 16150-1198 Phone: 1-724-962-3571 Fax:  1-724-962-4310 e-mail: mail@cattron-theimeg.com  Canada Cattron-Theimeg Canada Ltd. 150 Armstrong Avenue, Units 5 & 6 Georgetown, Ontario L7G 5G8 Phone: 1-905-873-9440 Fax:  1-905-873-9449 e-mail: salescdn@cattron-theimeg.com  United Kingdom Cattron-Theimeg (UK) Ltd. Riverdene Industrial Estate, Molesey Road, Hersham Walton-on-Thames, Surrey KT12 4RY Phone: 44-1932-247511 Fax:  44-1932-220937    e-mail: sales@cattronuk.com South Africa Cattron-Theimeg Africa (PTY.) Ltd. 24 O'Rielly Merry Road, Rynfield, Benoni P.O. Box 15444, Farrarmere, Benoni Gauteng 1518, South Africa Phone:  27-11-425-1123 Fax:  27-11-849-5717 e-mail:  cattron@iafrica.com  South America (Brazil) Cattron-Theimeg Américas Ltda. Rua Antonio Rodrigues de Carvalho, 435 13033-220 - Campinas – SP Phone:  55-19-3243-7803 Fax:  55-19-3243-9258 e-mail:  cattronamericas@cattron-theimeg.com   Europe (Germany) Cattron-Theimeg Europe GmbH & Co. Krefelder Straße 423-425 41066 Mönchengladbach Phone:  49-2161-63630 Fax:  49-2161-6363100 e-mail:    theimeg@theimeg.de   Internet Address for All CATTRON® Group International Companies: www.cattron-theimeg.com

Navigation menu