Chamberlain Group The 1D7437 Bluetooth Wireless Edge User Manual 01 38080 indd
Chamberlain Group Inc, The Bluetooth Wireless Edge 01 38080 indd
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2795192 |
| Application ID | ZU6ek0FAVPQ4eZ+g/sqiQQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 226.95kB (2836899 bits) |
| Date Submitted | 2015-10-27 00:00:00 |
| Date Available | 2015-10-27 00:00:00 |
| Creation Date | 2015-10-08 12:02:59 |
| Producing Software | Acrobat Distiller 10.1.15 (Macintosh) |
| Document Lastmod | 2015-10-20 12:13:43 |
| Document Title | 01-38080.indd |
| Document Creator | Adobe InDesign CS6 (Macintosh) |
| Document Author: | mrutledg |
MONITORED WIRELESS EDGE KIT MONITORED WIRELESS EDGE KIT MONITORED WIRELESS EDGE KIT Model/Modèle/Modelo LMWEKITU Review Copy To prevent possible SERIOUS INJURY or DEATH from a closing gate or door: • Be sure to DISCONNECT ALL POWER to the operator BEFORE installing the wireless edge kit. • The gate or door MUST be in the fully opened or closed position BEFORE installing the LiftMaster® Monitored Entrapment Protection device. • Correctly install and connect the wireless edge kit. • LiftMaster® Monitored Entrapment Protection devices are for use with LiftMaster® UL 325 compliant Gate and Commercial Door Operators ONLY. Use with ANY other product voids the warranty. • Monitored external entrapment protection devices MUST be installed per the operator installation manual for each Entrapment Zone. To prevent possible SERIOUS INJURY or DEATH from a closing gate or door: • Be sure to DISCONNECT ALL POWER to the operator BEFORE installing the wireless edge kit. • The gate or door MUST be in the fully opened or closed position BEFORE installing the LiftMaster® Monitored Entrapment Protection device. • Correctly install and connect the wireless edge kit. • LiftMaster® Monitored Entrapment Protection devices are for use with LiftMaster® UL 325 compliant Gate and Commercial Door Operators ONLY. Use with ANY other product voids the warranty. • Monitored external entrapment protection devices MUST be installed per the operator installation manual for each Entrapment Zone. ADVERTENCIA To prevent possible SERIOUS INJURY or DEATH from a closing gate or door: • Be sure to DISCONNECT ALL POWER to the operator BEFORE installing the wireless edge kit. • The gate or door MUST be in the fully opened or closed position BEFORE installing the LiftMaster® Monitored Entrapment Protection device. • Correctly install and connect the wireless edge kit. • LiftMaster® Monitored Entrapment Protection devices are for use with LiftMaster® UL 325 compliant Gate and Commercial Door Operators ONLY. Use with ANY other product voids the warranty. • Monitored external entrapment protection devices MUST be installed per the operator installation manual for each Entrapment Zone. ATTENTION AVERTISSEMENT AVERTISSEMENT AVERTISSEMENT Review Copy CARTON INVENTORY INVENTAIRE DE L’EMBALLAGE CONTENIDO DE LA CAJA Transmitter Transmitter Transmitter AA Lithium Batteries (2) Energizer® Ultimate Lithium AA L91 recommended as replacements AA Lithium Batteries (2) Energizer® Ultimate Lithium AA L91 recommended as replacements AA Lithium Batteries (2) Energizer® Ultimate Lithium AA L91 recommended as replacements Receiver Receiver Receiver I2C Dongle I2C Dongle I2C Dongle Mounting Bracket (2) Mounting Bracket (2) Mounting Bracket (2) 1" Screw (8) 1" Screw (8) 1" Screw (8) .375" Screw (8) .375" Screw (8) .375" Screw (8) INTRODUCTION The LiftMaster® Wireless Edge Kit provides a Bluetooth® connection between a LiftMaster® monitored resistive edge (not included) and the gate operator. Maximum range is 130 ft. (objects in the path of the signal and location of devices may reduce range). You can program up to 4 transmitters to the receiver. The kit works with LiftMaster® monitored resistive edge sensors ONLY. Contact closure edge sensors are NOT supported. For use with LiftMaster® gate operators that meet UL 325 requirements. Transmitter and receiver are UL Recognized Components and meet UL 325 requirements. A monitored safety device MUST be installed in each entrapment zone. INTRODUCTION The LiftMaster® Wireless Edge Kit provides a Bluetooth® connection between a LiftMaster® monitored resistive edge (not included) and the gate operator. Maximum range is 130 ft. (objects in the path of the signal and location of devices may reduce range). You can program up to 4 transmitters to the receiver. The kit works with LiftMaster® monitored resistive edge sensors ONLY. Contact closure edge sensors are NOT supported. For use with LiftMaster® gate operators that meet UL 325 requirements. Transmitter and receiver are UL Recognized Components and meet UL 325 requirements. A monitored safety device MUST be installed in each entrapment zone. Review Copy INTRODUCCIÓN The LiftMaster® Wireless Edge Kit provides a Bluetooth® connection between a LiftMaster® monitored resistive edge (not included) and the gate operator. Maximum range is 130 ft. (objects in the path of the signal and location of devices may reduce range). You can program up to 4 transmitters to the receiver. The kit works with LiftMaster® monitored resistive edge sensors ONLY. Contact closure edge sensors are NOT supported. For use with LiftMaster® gate operators that meet UL 325 requirements. Transmitter and receiver are UL Recognized Components and meet UL 325 requirements. A monitored safety device MUST be installed in each entrapment zone. 1 WIRE RECEIVER 1. Find the operator diagram on pages 12-18 to see the mounting location for the receiver and wire routing. 2. Open the receiver housing. 3. Route the wire harness from the receiver to the operator control board. Connect the wire harness to the “EXP. BOARD” terminal on the control board or to the expansion board (if installed) using the provided I2C dongle. Connect the dongle to the “TO MAIN BOARD” terminal on the expansion board. The blue power LED will come on. WIRE RECEIVER 1. Find the operator diagram on pages 12-18 to see the mounting location for the receiver and wire routing. 2. Open the receiver housing. 3. Route the wire harness from the receiver to the operator control board. Connect the wire harness to the “EXP. BOARD” terminal on the control board or to the expansion board (if installed) using the provided I2C dongle. Connect the dongle to the “TO MAIN BOARD” terminal on the expansion board. The blue power LED will come on. WIRE RECEIVER 1. Find the operator diagram on pages 12-18 to see the mounting location for the receiver and wire routing. 2. Open the receiver housing. 3. Route the wire harness from the receiver to the operator control board. Connect the wire harness to the “EXP. BOARD” terminal on the control board or to the expansion board (if installed) using the provided I2C dongle. Connect the dongle to the “TO MAIN BOARD” terminal on the expansion board. The blue power LED will come on. OR OU Control Board Tableau de commande Tarjeta de control To Main Control Board To Main Control Board To Main Control Board I C Dongle I2C Dongle I2C Dongle Expansion Board Tableau d’extension Tarjeta de expansión Review Copy Illustrations in manual are for reference only, your application may look different Les illustrations dans le manuel sont fournies à titre de référence uniquement; votre application peut avoir une autre apparence. Las ilustraciones del manual se ofrecen únicamente como referencia, su instalación podría ser diferente. 2 INSTALL TRANSMITTER BATTERIES AND SET EDGE DIRECTION 1. Open the transmitter housing. 2. Install the batteries. 3. Decide the direction (open or closed) the edge will be installed. Set “OPEN/CLOSE” DIP switch to match the direction of the edge protection. INSTALL TRANSMITTER BATTERIES AND SET EDGE DIRECTION 1. Open the transmitter housing. 2. Install the batteries. 3. Decide the direction (open or closed) the edge will be installed. Set “OPEN/CLOSE” DIP switch to match the direction of the edge protection. INSTALL TRANSMITTER BATTERIES AND SET EDGE DIRECTION 1. Open the transmitter housing. 2. Install the batteries. 3. Decide the direction (open or closed) the edge will be installed. Set “OPEN/CLOSE” DIP switch to match the direction of the edge protection. OPEN/CLOSE Dip Switches OPEN/CLOSE Dip Switches OPEN/CLOSE Dip Switches PROGRAMMING The receiver can learn up to 4 transmitters. 1. Press the learn button on the RECEIVER board. The red LED will come on and the operator control board will beep once to indicate programming mode. NOTE: Press the learn button again to exit programming mode. 2. Press the learn button on the TRANSMITTER to be learned. The red LED on the RECEIVER will blink 4 times. Press the learn button on the next TRANSMITTER to be learned. NOTE: Learn mode times out after 60 seconds if no transmitters are added or the capacity is reached. After each transmitter is learned there will be an additional 60 seconds to complete programming. PROGRAMMATION The receiver can learn up to 4 transmitters. 1. Press the learn button on the RECEIVER board. The red LED will come on and the operator control board will beep once to indicate programming mode. NOTE: Press the learn button again to exit programming mode. 2. Press the learn button on the TRANSMITTER to be learned. The red LED on the RECEIVER will blink 4 times. Press the learn button on the next TRANSMITTER to be learned. NOTE: Learn mode times out after 60 seconds if no transmitters are added or the capacity is reached. After each transmitter is learned there will be an additional 60 seconds to complete programming. PROGRAMACIÓN The receiver can learn up to 4 transmitters. 1. Press the learn button on the RECEIVER board. The red LED will come on and the operator control board will beep once to indicate programming mode. NOTE: Press the learn button again to exit programming mode. 2. Press the learn button on the TRANSMITTER to be learned. The red LED on the RECEIVER will blink 4 times. Press the learn button on the next TRANSMITTER to be learned. NOTE: Learn mode times out after 60 seconds if no transmitters are added or the capacity is reached. After each transmitter is learned there will be an additional 60 seconds to complete programming. Review Copy Learn Button Bouton Apprendre Botón de Programación 4 MOUNT THE RECEIVER 1. Find the operator diagram on pages 12-18 to see the mounting location for the receiver. 2. Attach the mounting bracket to the gate operator. 3. Reattach the receiver housing. 4. Snap the receiver onto the mounting bracket and secure with screw provided. MOUNT THE RECEIVER 1. Find the operator diagram on pages 12-18 to see the mounting location for the receiver. 2. Attach the mounting bracket to the gate operator. 3. Reattach the receiver housing. 4. Snap the receiver onto the mounting bracket and secure with screw provided. MOUNT THE RECEIVER 1. Find the operator diagram on pages 12-18 to see the mounting location for the receiver. 2. Attach the mounting bracket to the gate operator. 3. Reattach the receiver housing. 4. Snap the receiver onto the mounting bracket and secure with screw provided. Review Copy 5 WIRE AND MOUNT THE TRANSMITTER(S) NOTE: The transmitter can be wired to 1 or 2 edge sensors. 1. Route the wires from the edge sensor into the transmitter. Connect the wires to the terminal blocks (polarity is NOT important). 2. Attach the mounting bracket to the gate using the screws provided. If installing on a round surface, use zip ties (not provided). 3. Reattach the transmitter housing. 4. Snap the transmitters onto the mounting bracket and secure with the screw provided. WIRE AND MOUNT THE TRANSMITTER(S) NOTE: The transmitter can be wired to 1 or 2 edge sensors. 1. Route the wires from the edge sensor into the transmitter. Connect the wires to the terminal blocks (polarity is NOT important). 2. Attach the mounting bracket to the gate using the screws provided. If installing on a round surface, use zip ties (not provided). 3. Reattach the transmitter housing. 4. Snap the transmitters onto the mounting bracket and secure with the screw provided. WIRE AND MOUNT THE TRANSMITTER(S) NOTE: The transmitter can be wired to 1 or 2 edge sensors. 1. Route the wires from the edge sensor into the transmitter. Connect the wires to the terminal blocks (polarity is NOT important). 2. Attach the mounting bracket to the gate using the screws provided. If installing on a round surface, use zip ties (not provided). 3. Reattach the transmitter housing. 4. Snap the transmitters onto the mounting bracket and secure with the screw provided. Review Copy 6 TEST Apply pressure to edge. The red LED on the TRANSMITTER and the corresponding open or close edge LED on the gate operator control board will flash. If the TRANSMITTER LED does not flash, check the transmitter and edge sensor for proper installation and wiring. TEST Apply pressure to edge. The red LED on the TRANSMITTER and the corresponding open or close edge LED on the gate operator control board will flash. If the TRANSMITTER LED does not flash, check the transmitter and edge sensor for proper installation and wiring. TEST Apply pressure to edge. The red LED on the TRANSMITTER and the corresponding open or close edge LED on the gate operator control board will flash. If the TRANSMITTER LED does not flash, check the transmitter and edge sensor for proper installation and wiring. Status LED Status LED Status LED Review Copy BATTERY STATUS During normal operation, the red status LEDs on the transmitter(s) and receiver flash to indicate the battery status. NOTE: The receiver LED corresponds to the lowest battery level of all transmitters. 1 Flash Battery is fine. 2 Flashes Battery is low; the operator will beep twice. 3 Flashes Battery is critically low; the operator will not function until the battery is replaced. The operator will either open automatically (fail-safe) or latch at close (fail-secure) based on the operator setting (see the gate operator manual for more information). BATTERY STATUS During normal operation, the red status LEDs on the transmitter(s) and receiver flash to indicate the battery status. NOTE: The receiver LED corresponds to the lowest battery level of all transmitters. 1 Flash Battery is fine. 2 Flashes Battery is low; the operator will beep twice. 3 Flashes Battery is critically low; the operator will not function until the battery is replaced. The operator will either open automatically (fail-safe) or latch at close (fail-secure) based on the operator setting (see the gate operator manual for more information). BATTERY STATUS During normal operation, the red status LEDs on the transmitter(s) and receiver flash to indicate the battery status. NOTE: The receiver LED corresponds to the lowest battery level of all transmitters. 1 Flash Battery is fine. 2 Flashes Battery is low; the operator will beep twice. 3 Flashes Battery is critically low; the operator will not function until the battery is replaced. The operator will either open automatically (fail-safe) or latch at close (fail-secure) based on the operator setting (see the gate operator manual for more information). Transmitter Transmitter Transmitter Status LED Status LED Status LED Status LED Status LED Status LED Receiver Receiver Receiver Review Copy REMOVE A TRANSMITTER 1. Disconnect the edge sensor wires from the TRANSMITTER. 2. Remove the batteries from the TRANSMITTER. 3. Press and hold the RECEIVER learn button until the red status LED begins to flash (about 3 seconds) then release. The receiver will remove disconnected transmitters from memory and return to normal operation after 60 seconds or when the user presses the learn button again. REMOVE A TRANSMITTER 1. Disconnect the edge sensor wires from the TRANSMITTER. 2. Remove the batteries from the TRANSMITTER. 3. Press and hold the RECEIVER learn button until the red status LED begins to flash (about 3 seconds) then release. The receiver will remove disconnected transmitters from memory and return to normal operation after 60 seconds or when the user presses the learn button again. REMOVE A TRANSMITTER 1. Disconnect the edge sensor wires from the TRANSMITTER. 2. Remove the batteries from the TRANSMITTER. 3. Press and hold the RECEIVER learn button until the red status LED begins to flash (about 3 seconds) then release. The receiver will remove disconnected transmitters from memory and return to normal operation after 60 seconds or when the user presses the learn button again. 1-2 Learn Button Bouton Apprendre Botón de Programación Transmitter Transmitter Transmitter Receiver Receiver Receiver ERASE ALL TRANSMITTERS FROM MEMORY Press and hold the RECEIVER learn button until the red status LED begins to flash. Hold the learn button until the LED turns off (about 10 seconds) then release. The gate operator will beep for 5 seconds to confirm all transmitters are erased. ERASE ALL TRANSMITTERS FROM MEMORY Press and hold the RECEIVER learn button until the red status LED begins to flash then turns off (about 10 seconds) then release. The operator will beep for 5 seconds to confirm all transmitters are erased. ERASE ALL TRANSMITTERS FROM MEMORY Press and hold the RECEIVER learn button until the red status LED begins to flash then turns off (about 10 seconds) then release. The operator will beep for 5 seconds to confirm all transmitters are erased. Review Copy 10 TROUBLESHOOTING The diagnostic display on the operator control board will display an error code to indicate a problem. See the gate operator manual for instructions to display error codes. 46 67 68 Wireless edge battery low Wireless edge triggered more than 3 minutes Wireless edge loss of monitoring 69 Wireless edge triggered Replace batteries in wireless edge. Check wired input for wiring issue or obstruction. Check wireless edge inputs. Check for connection between receiver and main board/expansion board. IF an obstruction occurred, no action required. If an obstruction did NOT occur, check inputs and wiring. DÉPANNAGE The diagnostic display on the operator control board will display an error code to indicate a problem. See the gate operator manual for instructions to display error codes. 46 67 68 Pile faible du chant sans fil Chant sans fil déclenché pendant plus de 3 minutes Perte de surveillance du chant sans fil 69 Chant sans fil déclenché Remplacer les piles du chant sans fil. Vérifi er l’entrée câblée pour tout problème de câblage ouobstruction. Vérifi er les entrées du chant sans fil. Check for connection between receiver and main board/expansion board. Si une obstruction s’est produite, aucune action n’est requise. Si une obstruction ne s’est pas produite, vérifi er les entrées et le câblage. RESOLUCIÓN DE PROBLEMAS The diagnostic display on the operator control board will display an error code to indicate a problem. See the gate operator manual for instructions to display error codes. 46 67 68 Wireless edge battery low Wireless edge triggered more than 3 minutes Wireless edge loss of monitoring 69 Wireless edge triggered Replace batteries in wireless edge. Check wired input for wiring issue or obstruction. Check wireless edge inputs. Check for connection between receiver and main board/expansion board. IF an obstruction occurred, no action required. If an obstruction did NOT occur, check inputs and wiring. Control Board Tableau de commande Tarjeta de control DIAGNOSTICS Review Copy 11 MODEL RSW12U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODEL RSW12U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODEL RSW12U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. 7-1/2" (19.05 cm) 4-7/16" (11.27 cm) 6-1/8" (15.55 cm) RSW12U 7-1/2" (19.05 cm) 4-7/16" (11.27 cm) 6-1/8" (15.55 cm) Review Copy RSW12U 12 MODEL CSW24U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODÈLE CSW24U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODELO CSW24U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. 7-1/2" (19.05 cm) 4-7/16" (11.27 cm) 6-1/8" (15.55 cm) CSW24U 7-1/2" (19.05 cm) 4-7/16" (11.27 cm) 6-1/8" (15.55 cm) Review Copy 13 CSW24U MODELS RSL12U AND CSL24U - RECEIVER MOUNTING LOCATION MODÈLES RSL12U ET CSL24U - RECEIVER MOUNTING LOCATION MODELOS RSL12U Y CSL24U - RECEIVER MOUNTING LOCATION 5" (12.7 cm) 4-7/16" (11.27 cm) 1-3/4" (4.44 cm) RSL12U 1-1/2" (3.81 cm) 4-7/16" (11.27 cm) 3-3/16" (8.09 cm) Review Copy CSL24U 14 MODELS LA400, LA412, AND LA500 - RECEIVER MOUNTING LOCATION MODÈLES LA400U, LA412, ET LA500 - RECEIVER MOUNTING LOCATION MODELOS LA400U, LA412, Y LA500 - RECEIVER MOUNTING LOCATION 5-1/8" (13.01 cm)) 4-7/16" (11.27 cm) 1" (2.54 cm) STANDARD CONTROL BOX BOÎTER DE CONTRÔLE STANDARD CAJA DE CONTROL ESTÁNDAR STANDARD CONTROL BOX GRAND BOÎTER DE CONTRÔLE EN MÉTAL CAJA DE CONTROL METÁLICA GRANDE 1" (2.54 cm) 4-7/16" (11.27 cm) 3-1/2" (8.89 cm) Review Copy 15 MODEL CSW200U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODÈLE CSW200U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODELO CSW200U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. 8" (20.32 cm) 4-7/16" (11.27 cm) 3-3/4" (9.52 cm) CSW200U 9" (22.86 cm) 4-7/16" (11.27 cm) 1-1/2" (3.81 cm) Review Copy CSW200U 16 MODEL SL3000U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODÈLE SL3000U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODELO SL3000U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. 3-1/4" (8.25 cm) 4-7/16" (11.27 cm) 1" (2.54 cm) SL3000 Review Copy 17 MODELS SL585 AND SL595 - RECEIVER MOUNTING LOCATION MODÈLES SL585 AND SL595 - RECEIVER MOUNTING LOCATION MODELOS SL585 AND SL595 - RECEIVER MOUNTING LOCATION 4-1/16" (10.3 cm) 4-7/16" (11.27 cm) 1" (2.54 cm) SL585 6" (15.24 cm) 4-7/16" (11.27 cm) 11-3/4" (29.84 cm) 1" (2.54 cm) SL595 Review Copy .875" (2.22 cm) 18 WARRANTY LiftMaster® warrants to the first consumer purchaser of this product that it is free from defect in materials and/or workmanship for a period of 2 years from the date of purchase. GARANTIE LiftMaster® garantit à l’acheteur initial de ce produit que celui-ci est exempt de tout défaut matériel ou de fabrication pendant une période de deux ans suivant la date d’achat. GARANTÍA LiftMaster® garantiza al primer comprador minorista de este producto, que el mismo está libre de defectos de materiales y de mano de obra por un período de dos años a partir de la fecha de compra. NOTICE: This device complies with part 15 of the FCC rules and Industry Canada (IC) licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003. This device must be installed in a way where a minimum 8" (20cm) distance is maintained between users/bystanders and device. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. AVIS : Ce dispositif est conforme à la partie 15 des règles de la FCC et des normes RSS exemptées de licence d’Industrie Canada (IC). L’utilisation est assujettie aux deux conditions ci-après : (1) ce dispositif ne doit pas causer d’interférences nuisibles, et (2) ce dispositif doit accepter toute interférence reçue, y compris une interférence pouvant causer un fonctionnement indésirable. Tout changement ou toute modification non expressément approuvés par la partie responsable de la conformité pourrait annuler l’autorité de l’utilisateur d’utiliser l’équipement. Cet appareil numérique de classe B est conforme à la norme ICES-003 du Canada. This device must be installed in a way where a minimum 8” (20cm) distance is maintained between users/bystanders and device. Ce dispositif a été mis à l’essai et déclaré conforme aux limites établies pour les dispositifs numériques de classe B, conformément à l’article 15 des règles de la FCC. Cette conformité a pour but de fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement génère, utilise et peut émettre des fréquences radio et, s’il n’est pas installé et utilisé conformément aux instructions, causer des interférences nuisibles aux communications radio. Cependant, il n’existe aucune garantie que des interférences ne se produiront pas dans une installation particulière. Si cet équipement provoque des interférences nuisibles à la réception d’une diffusion sonore ou visuelle, ce qui peut être déterminé en l’allumant et en l’éteignant, l’utilisateur est invité à essayer de résoudre ce problème en prenant une ou plusieurs des mesures suivantes : - Réorienter ou déplacer antenne de réception. - Augmenter la distance entre l’équipement et le récepteur. - Brancher l’appareil à une prise sur un circuit différent de celui du récepteur. - Pour obtenir de l’aide, consulter le détaillant ou un radiotechnicien expérimenté. AVISO: Este dispositivo cumple con la Parte 15 de las normas FCC y las normas RSS con excepción de licencia de Industry Canada (IC) de Canadá. El uso está sujeto a las siguientes condiciones: (1) Este dispositivo no debe causar interferencia perjudicial, y (2) este dispositivo debe poder recibir interferencia, incluso interferencia que pueda afectar su funcionamiento. Todo cambio o toda modificación no expresamente aprobada por la parte responsable del cumplimiento podría anular el derecho de usar el equipo. Este aparato digital de Clase B cumple con las normas canadienses ICES-003 This device must be installed in a way where a minimum 8” (20cm) distance is maintained between users/bystanders and device. Este dispositivo ha sido probado y cumple con los límites establecidos para un dispositivo digital de Clase B según la Parte 15 de las Normas de FCC de EE.UU. Estos límites tienen por objeto brindar un grado razonable de protección contra interferencias molestas en una instalación residencial. Este equipo genera, usa y puede emitir energía de radiofrecuencia. Si no se instala y utiliza de acuerdo con las instrucciones podrá causar interferencia con comunicaciones radiales. Aun así, no hay garantía de que no se produzcan interferencias en una instalación particular. Si este equipo produce interferencia en la recepción de radio o televisión, lo cual puede determinarse apagando y encendiendo la unidad, el usuario debe tratar de corregir el problema por medio de lo siguiente: - Reorientar o reubicar la antena de recepción. - Aumentar la distancia de separación entre el equipo y el receptor. - Conectar el equipo a un tomacorriente de un circuito eléctrico diferente al que esté conectado el receptor. - Consultar al distribuidor del producto o a un técnico idóneo de radio y televisión. Review Copy 19 For parts and accessories visit LiftMaster.com Pour les pièces et accessoires, allez à LiftMaster.com En LiftMaster.com pueden adquirirse repuestos y accesorios LiftMaster® 845 Larch Avenue Elmhurst, IL 60126-1196 LiftMaster.com Review Copy The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. ALPHA © 2015, LiftMaster All Rights Reserved Tous droits réservés Todos los derechos reservados
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : mrutledg Create Date : 2015:10:08 12:02:59-07:00 Modify Date : 2015:10:20 12:13:43-07:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : Adobe InDesign CS6 (Macintosh) Metadata Date : 2015:10:20 12:13:43-07:00 Format : application/pdf Title : 01-38080.indd Creator : mrutledg Producer : Acrobat Distiller 10.1.15 (Macintosh) Document ID : uuid:0f7bb0fb-3f3f-6040-a196-02d789c4c940 Instance ID : uuid:6a6f9f1d-9265-9842-98b7-8eda0161996c Page Count : 20EXIF Metadata provided by EXIF.tools