Chamberlain Group The 2112 Remote Control Transmitter User Manual Exhibit D Users Manual per 2 1033 b3

Download:
Mirror Download [FCC.gov]
Document ID	529738
Application ID	vH98Jm3WtJU451uOvIRFUg==
Document Description	Exhibit D Users Manual per 2 1033 b3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.32kB (141509 bits)
Date Submitted	2005-04-08 00:00:00
Date Available	2005-04-08 00:00:00
Creation Date	0000-00-00 00:00:00
Document Lastmod	0000-00-00 00:00:00
Document Title	Exhibit D Users Manual per 2 1033 b3

3354/V) SAM/LE I/US7/Zuc’r/0/Vs
CH——_AM—BEFILAN
I-lf't Master:
ROFESS ONAL
MODEL 38LM 3-BUTTON REMOTE CONTROL TRANSMITTER
733 OWNER’S MANUAL
The green push button ls recommended for use with a
garage door opener. The other push buttons can he
“8°“ '° “Wm “WM °Pe"e' °"‘”°‘ “9“ W""°' To prevent possible SERIOUS INJURY or DEATH from a
”mun-Egg moving gate or garage door.
The 391- tton Remote Control Transmitter can - ALWAYS keep remote controls out of reach of children.
also be used with a flaw 3-channel receiver and a NEVER permlt children to operate, or play with remote
3-button door control to operate a commercial door control transmitters.
opener 1" OPEN “039; and “GP mode (88 explained 0" - Actlvate gate or door ONLY when it can be seen clearly, is
side 2)- properly adlusted, and there are no obstructions to door
. tmvel.
To match or change the code in the . . .
transmitter ALWAYS keep gate or garage door in eight untII completely
closed. NEVER permit anyone to cross path oi moving gate
Locate the code switches in both the new and the original or (1°05
transmitters The new transmitter‘s code switches can be .
found by sliding lhe battery compartment cover back. P'og’amm'"g the mne'
Place transmitters side by side as shown (Figure 1) and
set switches in all transmitters to matching positions
(+,0,—). Use a pen or screwdriver to slide the code
switches.
Figure 1
Maren code switch-s {Mt
between old him-litter and
m transmur (Code switch
in on the a-men remote
contra is donninl)
14 Press and release the “Ieam” button
”015.0011 switch m 0 located on the back panel at the motor
the 3 buttonelransmirter is" Figure 2 unit. The learn indicator light willglow
dormant when used m”, steadily for 30 seconds.
a single-button ’ 2.Within the 30 second window, press and
transmitter: Set code hold the button on the hand-held remote
5M,” W: i" ”79 . 34 The unit will either activate or the opener
Sing'ebutfon tit-owner, light bulb will blink signifying it has
to match the push button , Ieamed the code
selected on the a-butron my. Buttons _ .
(ramming, (figure 2)‘ If your unit has code swrtches.
1A Using a“ step ladder climb up to the back
of your motor unit. Check the code
switch settings on the back of the motor
units
Replacement Parts . Use a pen or screw driver to set the
Fl m housi code switches on the back 01 the
(citing: not ingfiided) A ' 4 _ .41A3580-4 transmitter to match the code switches
Visor clip 290125 on the back of the motor unit.
. Once the code switches have been set push the
12V bane” """"""""""""""" 10A“ transmitter button to activate your unit,
lnstall the control station and rec er where the door ls
visible, but away from the door and its hardware. When a
receiver is used to activate a commercial door opener, a TO prevent possible SER|0U5|NJURV ”DEATH:
reversing edge MUST be installed on the bottom 0! the door.
Failure to install a reversing edge under these circumstances
may result in SERIOUS INJURY or DEATH to persons trapped
beneath the door.
- NEVER allow small children near batteries.
The 12 volt battery should
produce power lor 1 year. To
replace the battery, slide the
battery compartment cover.
To use the transmitter with a 3-channel
receiver and 3-button door control to
operate a commercial door opener
Dispose at old batteries properly.
Replacing the transmitter battery
- It battery is swallowed. immediately notliy doctor.
ram-y. WERE ME m7 omen nszn smwcms ems
norm. lo cumpw wlh Fcc 1nd or lndtnhv Canada miss um. 1.1mm or mum.“ u this
rec-tool zoo/m transmitter m pra'lmitld, new! or cnanm m- md- smlnp or make-nu in.
[mud in Comply wan rcc summits Foil new on mm nsr. ovum-i k subimtn the
tulowlno m modifiers: n] this am my ml cause humlul Madam and (2) ml: device
must mpl my illlarlerem: lac-ind. lncllniltq lnletlemnce hut mw muse undesired apellllbtl.
148006284817
1. Use a screwdriver to pry open the
receiver cover (see illustration).
NOTE: The slide switch is factory set to the
MC. position (othemise the opener will not
operate). Verify this setting.
2. Select a remote control push button to
STOP the opener. (RED is
recommended.) Press and hold the
selected remote push button.
3. Then press and release the “Ieam'
button labeled “A" on the receiver, The
adiacent indicator light will FLASH.
Release the remote push button.
Repeat the procedure above with the yellow remote push
button and receiver ‘leam' button “B" its-program the
CLOSEoperation; and ‘again with the green remote push
button and receiver “learn" button “0" to program the
OPEN tunction ot the opener.
Retum the lront cover to the receiver.
(For this application, code switch settings need not be
changed.)
NOTE: If a remote control push button is not pressed
within 30 seconds, the indicator light adjacent to the
selected "learn" button Will turn OFE In that case, repeat
the programming.
@ 2004. The Chamberlain Group. Inc. ‘
luAtessE All Flights Reserved
FOR SERVlCE DIAL OUR TOLL-FREE NzuMBER:
Printed in Mexico

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2

EXIF Metadata provided by EXIF.tools