Chamberlain Group The 6421 Remote Control Finger Print Transmitter User Manual 114A

Chamberlain Group Inc, The Remote Control Finger Print Transmitter 114A

Exhibit D Users Manual per 2 1033 b3

Incorrect• Do not bend finger during the swipeas this will only scan the tip of yourfinger.• Swipe straight down, not at an angle.• Swipe flat, not tilted or rolled to oneside.1Model 139.53555 Security✚®EntryEaseNOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications ofthis receiver and/or transmitter are prohibited, except for changing the code setting or replacingthe battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this devicemust accept any interference received, including interference that may cause undesired operation.®To prevent possible SERIOUS INJURY or DEATH from a movinggate or garage door:• Install Keyless Entry Control within sight of the garage door, out ofreach of children at a minimum height of 5 feet (1.5 m), and awayfrom all moving parts of door.• ALWAYS keep remote controls out of reach of children. NEVERpermit children to operate, or play with remote controltransmitters.• Activate gate or door ONLY when it can be seen clearly, is properlyadjusted, and there are no obstructions to door travel.• ALWAYS keep gate or garage door in sight until completely closed.NEVER permit anyone to cross path of moving gate or door.WARNINGCAUTION WARNINGWARNINGOVERVIEW For use with any 315 MHz SECURITY✚®garage door openershaving a purple “learn” button. The EntryEase system uses biometric technology that enablesan authorized user to gain access by scanning their fingerprint.The sensor strip on the unit makes a numeric template of thefingerprint that is unique only to that user.Resend Button: When pressed the traveling door will reverse.The fingerprint sensor is inactive for15 seconds after valid swipe soreswiping will not reverse the door.Enroll Button: When pressed theEnroll LED will light up signalingthat the device is in enroll mode. READY LED: Lit (green) when unitis ready to accept a fingerprint scan.PASS LED: Lit (green) when ascanned fingerprint matches astored print.FAIL LED: Lit (red) when a scannedfingerprint does not match a storedprint.RETRY LED: Lit (yellow) when another swipe is required.ENROLL LED: Lit (yellow) when the unit is in enroll mode.SEND LED: Lit (yellow) after a passed fingerprint scan andenables the Resend button for retransmission.NOTE: The term “enroll” refers to scanning the fingerprint sothe device will recognize the user. The term “swipe” refers tothe movement of the finger across the sensor strip. The term“LED” stands for Light Emitting Diode.INSTALLATION1. Choose a convenientlocation for installation.Install out of the reach ofchildren at a minimumheight of 5 feet (1.5 m),away from all moving partsof door.For a one-piece door,choose the optionallocation shown in theillustration to avoid injury asthe door swings up and out.2. Remove the cover to access the topmounting hole by sliding past the “up stop”position.3. Center the unit at eye level against theselected location. Mark the bottom edge atthe center of the unit and remove from wall.Measure up 1-1/4" (3.2 cm) from this markto locate the bottom mounting hole. Be surethat you have at least 11" (28 cm)above thismark to allow for the removal of cover. Drilla 1/8" (3.2 mm) pilot hole. Install bottommounting screw, allowing 1/8" (3.2 mm) to protrude above surface.Position unit on screw head and adjust forsnug fit.With cover off so top mounting hole is visible, mark theposition of the hole. Remove unit and drill 1/8" (3.2 mm) pilothole. Replace unit and complete installation of top screw,using care to avoid cracking plastic housing. Do not overtighten. To replace cover, insert into tracks and slide down.Door Jamb Edge(Optional)Keyless EntryDoor Jamb Face(SECTIONAL DOOR ONLY)KEYLESS ENTRY MUST BE INSTALLED WITHIN SIGHT OF THE DOORExterior Front Wall1-Piece or Sectional DoorTypical InstallationSend LEDPass LEDReady LEDEnroll buttonEnroll LEDFail LEDRetry LEDUnit CoverSensor StripResend buttonTIPS FOR SUCCESSFUL ENROLLMENTCorrect1. Make sure finger is free of grease ordirt. Place finger flat above thesensor strip with the top knuckleabove the sensor.2. Swipe finger straight down keepingfirm contact with the sensor. Theswipe should be a slow, constantspeed.NOTE: Use the same finger for every swipe.UNIT MUST BE INSTALLEDWITHIN SIGHT OF THE DOOREntryEase1-1/4" (3.2 cm)Back View
1. Slide cover past the normal “up stop”position.2. Unscrew the two screws and remove thebattery cover.3. Replace the batteries. Screw the batterycover back on.4. Slide entry cover back into place.To prevent possible SERIOUS INJURY or DEATH:• NEVER allow small children near batteries.• If battery is swallowed, immediately notify doctor.WARNINGCAUTION WARNINGWARNINGTHE BATTERYThe batteries should produce power for at leastone year. Replace when the Fail LED flashesduring use.The unit requires 4 AAA batteries.Dispose of old batteries properly.FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-4-MY-HOME®(1-800-469-4663)ENROLLFAILRETRYSENDPASSREADYENROLLScrewsCoverBattery CoverReplacement parts:Unit cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41A579NOTE: The unit requires at least 3 good swipes to enroll a user.1. Ensure that Enroll LED and Ready LED are lit and not flashing.2. Swipe fingerprint down the sensor strip. ThePass LED will light briefly if a good swipewas achieved. If Retry LED lights followed by Ready LED, continue swiping until PassLED is lit.3. When enroll process is complete, the EnrollLED and Pass LED will flash.ENROLLING INITIAL USERENROLLFAI LRETRYSENDPAS SREADYENROLLTO ENROLL ADDITIONAL USERSThe device can store up to four fingerprints at a time.1. Turn unit on and wait for Ready LED to light.2. Press and hold Enroll button for 1 second.3. The Enroll LED will flash and an enrolled user must swipefingerprint to allow new enrollment.4. The Enroll LED and Ready LED will light up when ready forscan. The new user can now swipe their fingerprint. Thefingerprint will be swiped at least 3 times to ensure that agood scan is made.5. The Enroll LED and Pass LED will flash indicating successfulenrollment and unit will return to Ready mode.TO ERASE USERSNOTE: Erasing a user will erase ALL stored fingerprints andwill no longer be programmed to the opener.1. Enrolled user must swipe fingerprint.2. Press and hold the Enroll button for at least 6 seconds. ThePass LEDs will flash for 15 seconds. During this time theResend button is active. After 15 seconds the Enroll andReady LEDs will light indicating fingerprints are erased. Theunit will return to Enroll mode.ENROLLFAI LRETRYSENDPAS SREADYENROLLTROUBLESHOOTING• If no known enrolled users are available:— The unit must be reset using the Factory Reset process.• If the unit does not recognize a swiped fingerprint:— Ensure that the Ready LED is lit before you swipe.— Ensure that fingerprint is swiped correctly (See Tips forSuccessful Enrollment).— Ensure that fingerprint is enrolled.— Ensure that sufficient pressure is being applied to sensorstrip (do not press too hard).— The finger may need to be moistened if skin is too dry.• If the unit is Enroll mode at power up:— Complete enrollment process for initial user.— The initial enroll process failed (signalled by a lit EnrollLED and Fail LED) and must be repeated.• If enrolling new user and all LEDs flash and unit returns toReady mode:— The memory is full.• If the unit does not wake:— A button may be stuck. Press Enroll and Resend buttonsto ensure free movement.— The batteries may need to be replaced.NOTE: If sensor is dirty, user should wipe sensor with a cleanfinger to remove any residue. It is recommended that the sensorbe periodically cleaned with a lint-free cloth dampened withalcohol.® Registered Trademark / ™ Trademark / SM Service Mark of Sears, Roebuck and Co.114A3393 ® Marca Registrada / ™ Marca de Fábrica / SM Marca de Servicio de Sears, Roebuck and Co. © 2007 SearsFACTORY RESET1. When unit is on, press and hold the Enroll button until allLEDs turn off (approximately 6 seconds).2. Release the Enroll button.3. Press and hold the Enroll button until the Ready and EnrollLEDs are lit and not flashing. The unit will clear all enrolledusers and return to factory reset state.PROGRAMMING TO OPENERNOTE: The unit must have an enrolled user before it can beprogrammed to the opener.1. Press the purple “learn” button on the motor unit of theopener.2. Within 30 seconds, swipe enrolled fingerprint then press theResend button.NOTE: Due to the 30 second time interval, a second personmay be needed to press the “learn” button.OPERATION1. Open cover and unit will turn on. If cover is already open,press either the Resend or the Enroll button to turn unit on.2. When Ready LED is lit, swipe an enrolled finger.3. The Pass LED will flash and garage door will either open orclose depending on the door’s current state. The Fail LEDwill light if another swipe is required.

Navigation menu