Chamberlain Group The 7192 Remote Control Transmitter User Manual Exhibit D Users Manual per 2 1033 b3

Chamberlain Group Inc, The Remote Control Transmitter Exhibit D Users Manual per 2 1033 b3

Exhibit D Users Manual per 2 1033 b3

3-BUTTON REMOTE CONTROLSMODELS 953EV, 953EVC, 956EV AND 956EVCTo prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with remote controls.• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.For use with Chamberlain 315 MHz or 390 MHz garage door openers manufactured after January 1, 1993. The garage door opener activates when the programmed button on the remote control is pressed. The remote control can activate up to three garage door openers.Make sure the garage door opener has a working light bulb because it is a programming indicator.® LED LEDLocate the Program button on the remote control.Locate the Learn button on the garage door opener.NOTE: Your garage door opener may look different.OR ORLearn LEDLearn LEDLearn LEDGreenorRed/OrangePurple Yellow Program ButtonProgram Button23Press and release the remote control button you want to use...4To exit programming mode, press any remote control button except the button that was just programmed.Install the visor clip.6The garage door opener will activate.To test, press the programmed button on the remote control...1Press and release the Learn button on the garage door opener.Within 30 seconds... To enter programming mode, use the visor clip to press the Program button until the LED on the front of the remote control turns on.The Learn LED will light.Check to see if the garage door opener light bulb blinks. If not, wait for the remote control LED to light solid then slowly press and release the remote control button again. Repeat until the light bulb blinks. DO NOT press the button after the light bulb blinks. 5MODELS 953EV AND 953EVC MODELS 956EV AND 956EVCGARAGE ACCESS SYSTEM REMOTEGARAGE ACCESS SYSTEM KEYCHAIN REMOTEPREPAREPROGRAM THE REMOTE CONTROL (953EV & 953EVC)953EV & 953EVC956EV & 956EVC
4To exit programming mode, press any remote control button except the button that was just programmed.The garage door opener will activate.To test, press the programmed button on the remote control...Using a safety pin or paper clip, press the Program button until the LED on the front of the remote control turns on. 12Press and release the Learn button on the garage door opener.Within 30 seconds...The Learn LED will light.3Press and release the remote control button you want to use...Check to see if the garage door opener light bulb blinks. If not, wait for the remote control LED to light solid then slowly press and release the remote control button again. Repeat until the light bulb blinks. DO NOT press the button after the light bulb blinks.5 NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.BATTERYThe LED on your remote will stop flashing when the battery is low and needs to be replaced.To replace battery, open the case as shown. Insert battery positive side up (+). Replace the battery with only 3V2032 coin cell batteries. Dispose of old battery properly. To prevent possible SERIOUS INJURY or DEATH:• NEVER allow small children near batteries.• If battery is swallowed, immediately notify doctor.To reduce risk of fire, explosion or chemical burn:• Replace ONLY with 3V2032 coin batteries.• DO NOT recharge, disassemble, heat above 212° F (100° C) or incinerate.1-800-528-9131114A3924 © 2011, The Chamberlain Group, Inc. All Rights Reserved REPLACEMENT PARTSBattery . . . . . . . . . . . . . . . . . . . . . . . . . . 10A20Visor Clip (Models 953EV & 953EVC ONLY) . . . . 20B137123WARRANTYwww.chamberlain-diy.comONE YEAR LIMITED WARRANTYThe Chamberlain Group, Inc. warrants to the first retail purchaser of this product that is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase.Pry open the case with a screwdriver blade.956EV & 956EVCPry open the case first in the middle (1), then at each side (2 and 3) with the visor clip.953EV & 953EVCPROGRAM THE REMOTE CONTROL (956EV & 956EVC)

Navigation menu