Chamberlain Group The 7510 Remote Control Transmitter User Manual
Chamberlain Group Inc, The Remote Control Transmitter
user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1454045 |
| Application ID | boPoThjj8S92O/6iTpcJhQ== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 270.8kB (3384955 bits) |
| Date Submitted | 2011-04-26 00:00:00 |
| Date Available | 2011-05-24 00:00:00 |
| Creation Date | 2011-03-22 07:09:31 |
| Document Lastmod | 2011-04-18 10:40:07 |
| Document Title | user manual |
3-BUTTON REMOTE CONTROLS MODELS 890MAX, 893MAX, AND 895MAX Can be used as a replacement remote control for 80 Series, 970 Series, and 370 Series LiftMaster remote controls. MODEL 895MAX LEDs Compatible with 315 MHz or 390 MHz garage door openers manufactured after January 1, 1993. Make sure the garage door opener has a working light bulb because it is a programming indicator. MODEL 893MAX LED For use with gate operators, commercial door operators, or other products that are 315 MHz or 390 MHz and have a Learn button. Refer to your product manual for the location of the Learn button. MODEL 890MAX LED To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with remote controls. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. PREPARE Locate the Learn button on the garage door opener. NOTE: Your garage door opener may look different. Learn LED OR 890MAX Program Button OR Learn LED Learn LED Green or Red/Orange Locate the Program button on the remote control. 895MAX Purple 893MAX Yellow PROGRAMMING THE REMOTE CONTROL 1 To enter programming mode, press the Program button until the LED on the front of the remote control turns on. 890MAX 2 Press and release the Learn button on the garage door opener. 893MAX Visor Clip 895MAX Safety Pin or Paper Clip The Learn LED will light. Within 30 seconds... 4 To exit programming mode, press any remote control button except the button that was just programmed. 3 Press and release the remote control button you want to use... Check to see if the garage door opener light bulb blinks. If not, wait for the remote control LED to light solid then slowly press and release the remote control button again. Repeat until the light bulb blinks. DO NOT press the button after the light bulb blinks. 5 To test, press the programmed button on the remote control... 6 Install the visor clip (not applicable for Model 890MAX). The garage door opener will activate. HOW TO USE THE REMOTE CONTROL Press and hold the button down until the door or gate starts to move. The remote control will operate from up to 3 car lengths away on typical installations. Installations and conditions vary, contact an installing dealer for more information. Additional buttons on the remote control can be programmed to operate up to 3 devices such as additional garage door openers, light controls, gate operators or access control systems. BATTERY The LED(s) on your remote control will stop flashing when the battery is low and needs to be replaced. To replace battery, open the case as shown. Insert battery positive side up (+). Replace the battery with only 3V2032 or 3V2016 coin cell batteries (depending on the model). Dispose of old battery properly. 893MAX 895MAX 890MAX Pry open the case first in the middle (1), then at each side (2 and 3) with the visor clip. Pry open the case with a screwdriver blade. Remove the two screws and open the case. 3V2032 3V2016 To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. To reduce risk of fire, explosion or chemical burn: • Replace ONLY with 3V2032 coin batteries. • DO NOT recharge, disassemble, heat above 212° F (100° C) or incinerate. NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARRANTY REPLACEMENT PARTS ONE YEAR LIMITED WARRANTY The Chamberlain Group, Inc. warrants to the first consumer purchaser of this product that it is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase. 3V2032 Lithium Battery (Models 893MAX & 890MAX). . . . . . . . . . 10A20 3V2016 Lithium Battery (Model 895MAX) . . . . . . . . . . . . . . . . . . . . 10A19 Visor Clip (Model 893MAX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29B137 Visor Clip (Model 895MAX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29C151 www.liftmaster.com 1-800-528-9131 114A3930 © 2011, The Chamberlain Group, Inc. All Rights Reserved
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Create Date : 2011:03:22 07:09:31-07:00 Modify Date : 2011:04:18 10:40:07-05:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2011:04:18 10:40:07-05:00 Format : application/pdf Document ID : uuid:f945024c-d22f-6c42-b845-c9f354c8a18c Instance ID : uuid:ae46a3c5-1902-42b4-822a-b57536c457f0 Page Count : 2EXIF Metadata provided by EXIF.tools