Chamberlain Group The 7966 FCC Part 15 Remote Control Transmitter User Manual r1 En

Download:
Mirror Download [FCC.gov]
Document ID	1926493
Application ID	3jGnSWnksBL8+gE9H7gKLg==
Document Description	User Manual_r1_En
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	273.72kB (3421495 bits)
Date Submitted	2013-03-27 00:00:00
Date Available	2013-03-21 00:00:00
Creation Date	2013-03-27 17:59:54
Document Lastmod	2013-03-27 18:00:23
Document Title	User Manual_r1_En

3-BUTTON REMOTE CONTROLS
MODELS 890MAX, 893MAX, AND 895MAX
Can be used as a replacement remote control for 80
Series, 970 Series, and 370 Series LiftMaster remote
controls.
MODEL 895MAX
LEDs
Compatible with 315 MHz or 390 MHz garage door
openers manufactured after January 1, 1993. Make
sure the garage door opener has a working light bulb
because it is a programming indicator.
MODEL 893MAX
LED
For use with gate operators, commercial door
operators, or other products that are 315 MHz or 390
MHz and have a Learn button. Refer to your product
manual for the location of the Learn button.
MODEL 890MAX
LED
To prevent possible SERIOUS INJURY or
DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of
reach of children. NEVER permit children
to operate or play with remote controls.
• Activate gate or door ONLY when it can be
seen clearly, is properly adjusted and there
are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight
until completely closed. NEVER permit
anyone to cross path of moving gate or
door.
PREPARE
Locate the Learn
button on the garage
door opener.
NOTE: Your garage door
opener may look different.
Learn
LED
OR
890MAX
Program Button
OR
Learn
LED
Learn
LED
Green
or
Red/Orange
Locate the Program button on
the remote control.
895MAX
Purple
893MAX
Yellow
PROGRAMMING THE REMOTE CONTROL
1 To enter programming mode, press the Program button
until the LED on the front of the remote control turns on.
890MAX
2 Press and release the
Learn button on the
garage door opener.
893MAX
Visor Clip
895MAX
Safety Pin or
Paper Clip
The Learn LED will light.
Within 30 seconds...
4 To exit programming mode, press
any remote control button except
the button that was just programmed.
3 Press and release the remote control button
you want to use...
Check to see if the garage
door opener light bulb
blinks.
If not, wait for the remote
control LED to light solid
then slowly press and
release the remote
control button again.
Repeat until the
light bulb blinks.
DO NOT press the
button after the light
bulb blinks.
5 To test, press the programmed button on
the remote control...
6 Install the visor clip (not
applicable for Model 890MAX).
The garage door opener
will activate.
HOW TO USE THE REMOTE CONTROL
Press and hold the button down until the door or gate starts to move.
The remote control will operate from up to 3 car lengths away on typical
installations. Installations and conditions vary, contact an installing dealer
for more information.
Additional buttons on the remote control can be programmed to operate
up to 3 devices such as additional garage door openers, light controls,
gate operators or access control systems.
BATTERY
The LED(s) on your remote control will stop flashing when the battery is low and needs to be
replaced. To replace battery, open the case as shown. Insert battery positive side up (+). Replace
the battery with only 3V2032 or 3V2016 coin cell batteries (depending on the model). Dispose of
old battery properly.
893MAX
895MAX
890MAX
Pry open the case first in the
middle (1), then at each side
(2 and 3) with the visor clip.
Pry open the case with a
screwdriver blade.
Remove the two screws
and open the case.
3V2032
3V2016
To prevent possible SERIOUS INJURY or
DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify
doctor.
To reduce risk of fire, explosion or chemical
burn:
• Replace ONLY with 3V2032 coin batteries.
• DO NOT recharge, disassemble, heat
above 212° F (100° C) or incinerate.
NOTICE: To comply with FCC and or Industry Canada rules (IC),
adjustment or modifications of this receiver and/or transmitter
are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE
PARTS.
This device complies with Part 15 of the FCC rules and IC RSS210. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
WARRANTY
REPLACEMENT PARTS
ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first consumer purchaser
of this product that it is free from defect in materials and/or
workmanship for a period of 1 year from the date of purchase.
3V2032 Lithium Battery (Models 893MAX & 890MAX). . . . . . . . . . 10A20
3V2016 Lithium Battery (Model 895MAX) . . . . . . . . . . . . . . . . . . . . 10A19
Visor Clip (Model 893MAX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29B137
Visor Clip (Model 895MAX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29C151
www.liftmaster.com
1-800-528-9131
114A3930B
© 2013, The Chamberlain Group, Inc.
All Rights Reserved

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2013:03:27 17:59:54-07:00
Modify Date                     : 2013:03:27 18:00:23-07:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2013:03:27 18:00:23-07:00
Format                          : application/pdf
Document ID                     : uuid:d86ef694-5559-4aa3-9ae1-b9f7f973e4c4
Instance ID                     : uuid:f43aec31-ecef-4ad0-acc9-f5a0c61d3021
Page Count                      : 2

EXIF Metadata provided by EXIF.tools