Chamberlain Wireless PIR2 Passive Infared Sensor 2 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	932242
Application ID	pgADmZMQscXiy4zaKoMPlw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	35.6kB (445036 bits)
Date Submitted	2008-04-23 00:00:00
Date Available	2008-04-23 00:00:00
Creation Date	2007-12-13 11:25:10
Document Lastmod	2007-12-13 11:25:10
Document Title	User Manual

Model PIRV400R
®
Wireless Pedestrian & Vehicle Sensor with Voice
Overview
Intercom Feature: When PIR Motion Sensor has
detected motion, the Base Station will allow you to
listen through the PIR Motion Sensor for 10 seconds.
If you wish to talk to the person on the other end,
hold down the Talk button and speak, releasing it to
hear.
The PIR Motion Sensor only works with
Chamberlain's Wireless Pedestrian & Vehicle Alert
with Voice (Model RWV400R). The PIR Motion
Sensor can be used to monitor motion up to 30' away
and can transmit a signal up to 1000' away from the
Base Station (not included). The Passive Infra-Red
sensor detects movement of people and vehicles,
while allowing small animals to pass through
undetected. The PIR Motion Sensor has a built-in
microphone and speaker that allows for
communication between the Base Station and the
Sensor. When the PIR Motion Sensor detects
movement a signal is sent to the base station which
alerts the homeowner with sounds and lights. The
Alert can also remotely control an electrical device
near the PIR Motion Sensor like a light or a
camera (See Advanced Features).
Volume: Pressing the Volume button repeatedly will
cycle through volume levels.
Mute: To temporarily mute Base Station, hold the
Volume and Talk buttons down for three seconds. The
Base Station will reactivate after one hour, or by
pressing the Talk button.
Remote Button: If there is an accessory device
connected to the relay on the PIR Motion Sensor, it
can be activated by pressing the Remote button
within 30 seconds of the signal from the alert buzzer.
Carton Inventory
Switch #1:
OFF
Buzzer Off
ON
Buzzer On (Default)
OFF
Swivel Bushing
Switch #2:
OFF
Long Buzz
ON
Short Buzz (Default)
Mounting Plate
Operation & Features
Talk
(Power - On)
Remote
Activation
Button
Learn
Button
Speaker
ON
Clear Memory: Press and hold the Learn button on
the Base Station until 3 beeps are heard. If PIR
Motion Sensor signals while Learn button is pressed,
repeat the procedure.
Base Station
(not provided)
PIR Sensor/Test Light
Battery: The AA Alkaline batteries (not provided) will
last up to 2 years depending on use (Lithium batteries
recommended for colder environments). If PIR Motion
Sensor batteries are low Base Station will emit three
high-pitch beeps every ten minutes. If Base Station
batteries are low it will emit two high-pitch beeps.
Passive Infra-Red (PIR)
Motion Sensor
PIR Motion
Sensor
Volume Button
Programming Additional PIR Motion Sensors:
Each Base Station can learn the code of up to 8 PIR
Motion Sensors, responding with multiple buzzes. To
program additional PIR Motion Sensors see Step 6.
Relay Output
Contacts
AC Adapter
Switch #1: Mute
Switch #2: Tone
On/Off: To turn Base Station OFF hold down the
Volume button until a beep is heard and light goes
out. To turn Base Station ON press the Talk button.
PIR Motion Sensor Assembly &
Test
Programming PIR Motion
Sensor to Base Station
Step 1
Step 6
Connect PIR Motion
Sensor box to
mounting plate with
silver screw. Tighten
screw until PIR Motion
Sensor stays in place
when repositioned.
Step 2
Step 3
A Ensure that Base
Station and PIR
Motion Sensor are in
close proximity to
each other. Press and
release learn button
on Base Station.
Buzzer will sound.
A Install 4 AA Alkaline
batteries (not
provided). (Lithium
batteries
recommended for
colder
environments.)
B Ensure batteries do
not touch circuit
board.
B Within 5 seconds, wave hand in front of PIR Motion
Sensor. Test light will illuminate and Base Station
will activate with static and feedback after several
seconds.
Test PIR Motion
Sensor by waving
hand in front of
sensor. Test light
should flash after
several seconds.
PIR Motion Sensor Installation
Step 7
Mount PIR Motion
Sensor vertically on
solid surface a few feet
off the ground and
within 1000' of Base
Station. Unit should be
able to swivel as
needed.
Step 4
Secure cover with the
two large black
screws.
NOTE: Do not mount PIR Motion Sensor in direct
sunlight, near moving tree branches, or in the path of
a sprinkler system.
Vehicle Alert Installation: For cars, the best
mounting position is about 4' high, between 10-20'
back, and angled to see the back of car after passing
the sensor.
Step 5
10' - 20'
OPTIONAL
3' - 5'
Ensure Base Station (not
provided) has power.
Advanced Features
Troubleshooting
Both the PIR Motion Sensor and Base Station have
relays which can activate other electrical devices. The
relay switches can handle up to 120 AC volts at 10
amps. The accessory device will need a separate
power supply.
The Alert does not function.
Check batteries in PIR Motion Sensor. Ensure Base
Station has power. Ensure PIR Motion Sensor is
programmed to Base Station.
The Alert is not getting expected transmission
range.
Ensure Base Station antenna is vertical and keep PIR
Motion Sensor away from trees and metal objects.
Ensure Base Station is in clearest possible range of
PIR Motion Sensor. The less objects between
devices, the longer the range.
Base Station: The relays can be
used to activate louder alarm bells,
lights, cameras, or other accessories.
PIR Motion Sensor: The relays will
only activate when the remote button
is pressed on the Base Station. To
prevent access to these relays flush
mount the PIR Motion Sensor.
Base Station is not very loud.
Adjust the volume of speaker. An accessory such as a
bell, buzzer or light can be attached to the relay
switch. The relay switch can handle up to 120 AC
volts at 10 amps. The accessory device will need
separate power supply.
Static and feedback is heard in Base Station.
PIR Motion Sensor is too close to the Base Station.
The PIR Motion Sensor is detecting motion only
part of the time.
To detect cars, it is best to mount PIR Motion Sensor
at height of car’s motor and have it between ten and
twenty feet from the road. Swivel sensor as needed.
The Alert is giving false alarms.
Check for moving tree branches or insects in sensor
window. PIR sensor can also be triggered by light
shining directly in sensor window, such as reflected
sunlight, or motion in front of a light source.
Base Station beeps every ten minutes.
If there are two beeps the battery is low in the Base
Station. Replace with AA Alkaline batteries or operate
it with AC Adapter. If there are three beeps the battery
is low in the PIR Motion Sensor. Replace with AA
Alkaline batteries.
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:
1-800-528-9131
www.chamberlain-DIY.com
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.
THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
114A3516
© 2007, The Chamberlain Group Inc.
All Rights Reserved

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:08:23
Modify Date                     : 2007:12:13 11:25:10-07:00
Create Date                     : 2007:12:13 11:25:10-07:00
Metadata Date                   : 2007:12:13 11:25:10-07:00
Format                          : application/pdf
Document ID                     : uuid:d1131fb7-f3e5-4135-ab22-97d3cd4fc3ee
Instance ID                     : uuid:bda1dbd0-3ba6-439a-a939-006510e4f8fd
Page Count                      : 4

EXIF Metadata provided by EXIF.tools