Chantry Networks BP200E ACCESS POINT WITH WLAN AND UNII User Manual addendum QS1

Download:
Mirror Download [FCC.gov]
Document ID	474560
Application ID	UH8JVzWhDSheUw6vYO1Wsw==
Document Description	USER MANUAL 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.29kB (41069 bits)
Date Submitted	2004-09-30 00:00:00
Date Available	2004-09-30 00:00:00
Creation Date	2004-06-17 17:00:15
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2004-08-10 09:19:39
Document Title	Microsoft Word - addendum QS1.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	bsiew

Caution:
•
•
•
•
There should be at least 9 inches (20 cm) separation between the
BeaconPoint and users.
Any changes or modifications not expressly approved by Chantry
Networks could void the user’s authority to operate the equipment.
The BeaconPoints shall be powered by UL approved limited power source
adapter or UL approved limited power source power over ethernet
(P.O.E.).
The BP200 product will automatically discontinue transmission in case of
either absence of information (no frames transmitted through Ethernet) to
transmit or operational failure.
Chantry
Beaconworks
Addendum to Quick Start Guide
Release 1.1
Updated June 17th, 2004
Warning:
•
•
•
When the BP200E is enabled in the 5.15 to 5.25 GHz band, it is
authorized for indoor deployment only.
When the BP200E is enabled in the 5.15 to 5.25 GHz band, the antennas
are permanently attached to the access point. Do not attempt to disconnect.
Install ferrite bead onto the BeaconPoint 200 data cord as
illustrated below.
Ferrico
K1 NF-65 BK 2
Note:
The BP200 has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
RJ45 Data Cord,
•
Install ferrite beads onto the BeaconMaster power and data
cords as illustrated below.
Steward
28A5776-0A2
Power Cord,
Steward
28A2024-0A0
RJ45 Data Cord,

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:69c86806-a00b-4f18-891d-415f882186eb
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2004:06:17 17:00:15-04:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2004:08:10 09:19:39-04:00
Metadata Date                   : 2004:08:10 09:19:39-04:00
Document ID                     : uuid:b106911e-2092-4e95-9c25-24fff78f7c31
Format                          : application/pdf
Title                           : Microsoft Word - addendum QS1.doc
Creator                         : bsiew
Author                          : bsiew

EXIF Metadata provided by EXIF.tools