Checkpoint Systems MMRO7000 Performa Mullion Mount Proximity Reader User Manual
Checkpoint Systems Inc Performa Mullion Mount Proximity Reader
User Manual
Performa Mullion Mount (AC-125M) RFID Proximity Reader Background The following will discuss Performa Mullion Mount Proximity Reader as they are intended to install on an Access Control System by Checkpoint Systems, Inc. This reader is available in two colors; Gray (Model # AC-125MG - Part# 304627) and Off-White (Model# AC-125MW - Part # 140058). Specifications The Mullion Mount proximity reader is suitable to mount on metal, such as door mullions, with no impact on performance. This device is designed to use the 26-Bit Weigand data format and is targeted to operate at 12VDC @ 150mA, but is capable of operating between 10.8VDC and 14.8VDC. For these readers to perform properly, the installation must use Belden 5304FE or equivalent wire. This proximity reader has a read range of up to 4” using the Performa Proximity Plus Cards from Checkpoint. The reader will transmit a frequency of 13.56MHz and will operate between –22°F and 150°F. The Performa reader carries the FCC Part 15USA certification. Performa Mullion Mount Reader Dimensions The following is a drawing of the outer dimensions of this proximity reader. Wiring The Performa readers come with six wires, but currently only five wires will be used. As mentioned above this reader is a Weigand device and uses the 26-Bit Weigand format. The wire specification is Belden 5304FE or equivalent. The wire is 18 gauge, six conductors, stranded, and shielded. With this wire the reader can mount up to 500’ from the controller, as stated within the Weigand specification. The standard color-coding has been used: Black Red White Green Brown Blue Common Power for Reader (12VDC) Data 1 Data 0 LED Control Beeper Control (Not Used At This Time) The following is a diagram of wiring the Performa reader to a Checkpoint Terminal Controller: Battery Jum per7 and 8 N um bering 3 (top) 12v 2 (center) 5v 1 (bottom ) JM P 8 Reader1 V oltage JM P 7 Reader2 V oltage LED "0" "1" 5V G ND Brown Green White Red Black Note: Please refer to your hardware for use of the beeper control and the sixth wire. Checkpoint does not land the beeper control wire to its own board. Dip Switch Settings LED and beeper features are controlled by a dip switch pack located on the back of the reader. The first three positions of the dip switch pack is all that is needed to change the output of the LED and beeper. The fourth dip switch is reserved for future use. The following chart shows the dip switch setting and functionality of the LED and beeper. The LED is bi-color and can provide Red, Green, and Amber states. The beeper is a standard piezo or magnetic beeper. Switches SW 1 ON ON ON OFF OFF SW 2 ON ON OFF ON OFF Note SW 3 ON OFF OFF ON OFF LED Ready GREEN RED RED RED RED Denied R/G FLASH Beeper Admit RED 3s GREEN 3s R/G FLASH R/G FLASH R/G FLASH NO CHANGE FLICKERS FLICKERS GREEN 3s Denied 3 SHORT 3 SHORT 3 SHORT 3 SHORT CHIRPS Admit NONE NONE 1 LONG 1 LONG CHIRPS Notes: 1. This is a test mode for the reader. This strictly tests the reader itself and indicates no functionality of the Terminal Controller.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:10:24 14:53:43 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2001:10:24 14:53:45-04:00 Page Count : 2EXIF Metadata provided by EXIF.tools