Cheng Uei Precision Industry H500 Bluetooth Headset User Manual

Cheng Uei Precision Industry Co., Ltd. Bluetooth Headset

Contents

Part 1Info to be included in Manual

2005/4/11 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
DRAFT1 - CHARGE2 - START BLUETOOTH3 - PAIR4 - TEST AND USE Get Connected in4 Quick StepsQuick Start GuideH500Bluetooth®Handsfree HeadsetBEFORE YOU BEGIN1Charge your headset for 2 hours:Plug the Motorola charger into the top of the headset with the release tab facing up.The LED indicator light turns on when the device is charging. It may take up to 1 minute for the LED to turn on. When the device is fully charged (about 2 hours), the LED indicator turns off.Disconnect the charger.12Before using this product, read the Important Safety and Legal Information included in your phone's user's guide, and follow its instructionsCHARGEYour HeadsetEar PieceSTART BLUETOOTH FeatureYour Headset2Select (Menu) > Settings > Connection > Bluetooth Link > Setup.Scroll to Power.Select Change.Scroll to On.Press Select to turn on Bluetooth. Bluetooth remains on until you turn the feature off.Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide.12345Your phone's Bluetooth feature is off by default. To use your headset, the Bluetooth feature must be turned on in your phone.For most Motorola phones:M(PAIRYour Headset33Call ButtonWith the headset power off, press and hold the Call button for 4 to 5 seconds and then release. The power turns on and the headset goes into pairing mode. When the headset is in pairing mode, the LED indicator light turns on and remains steadily lit.If the LED indicator light is flashing or does not remain steadily lit, repeat these steps.12Before you can use your headset, you must pair (link) it with your phone.Step A - PUT THE HEADSET IN PAIRING MODEPAIR CONTINUEDYour PhoneFor most Motorola phones:On your Motorola phone, select (Menu) > Settings > Connection > Bluetooth Link > Handsfree > Look for Devices. The phone lists all Bluetooth devices it finds.Select Motorola H500.Select OK or Yes to pair (bond) the handsfree device.Enter the passkey: 0000Select OK.When your device is successfully paired with your phone, the LED indicator light changes from steadily lit to flashing.Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide.Step B - SET THE PHONE TO LOOK FOR YOUR HEADSET34512M(TEST AND USEYour phone and headset are now paired and ready to make and receive calls. To confirm they are successfully paired and operating properly, make a call: Open the ear piece and place over your ear.On your phone, dial the number you want to call.Press Send to make the call. If your phone and headset are successfully paired, you will hear ringing.After you have successfully paired your phone and headset, you do not need to repeat these steps.412USING YOUR H500 TROUBLESHOOTINGMy phone does not find my headsetMake sure your headset is in pairing mode before looking for devices on your phone(see step 3).My headset worked before but now it'snot working.Make sure your phone is on and the Bluetooth feature is turned on in your phone (step 2). If the Bluetooth feature has been turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 2) and pair your phone and headset again (see step 3).Support.If you need more help, contact us at1- 877-MOTOBLU.MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. All other product or service names are the property of their respective owners. © Motorola, Inc. 2005.Motorola, Inc.Consumer Advocacy Office1307 East Algonquin RoadSchaumburg, IL 60196www.hellomoto.com1-877-MOTOBLU1-800-331-6456 (United States)1-888-390-6456 (TTY/TDD United States for hearing impaired)1-800-461-4575 (Canada)Guide Number: <TBD>3Take a moment before you get started to familiarize yourself with your newH500 Handsfree Headset.VolumeButtonsLED Indicator LightCall ButtonMicrophoneLED Indicator LightSee Quick Use on the reverse side of this guidefor information onusing your H500.

Navigation menu