Chengdu Ebyte Electronic Technology E32-TTL-100 Wireless transceiver module User Manual E32 TTL 100 Datasheet V1 0

Chengdu Ebyte Electronic Technology Co., Ltd. Wireless transceiver module E32 TTL 100 Datasheet V1 0

User manual

E32-TTL-100 Datasheet V1.0                                       Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046                     Website: www.cdebyte.com Professional R&D RF Module         2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  1  of  14         The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All E32-TTL-100 Datasheet V1.0  .1.Introduction                                         E32-TTL-100       1.1  Feature                                                   E32-TTL-100          E32-TTL-100 is a wireless transceiver module with LoRa spread-spectrum technology,  operates  at  434MHz,  based  on  original  imported  RFIC  SX1278 from SEMTECH, transparent transmission is available,  TTL  level. The module adopts  LoRa  spread-spectrum  technology,  which  means  the  transmitting distance is much longer than before. The advantages of this module is more concentrated power density and better anti-interference performance.       The module features FEC (Forward Error Correction) algorithm, which ensure its high coding efficiency & good correction performance. In the case of sudden interference, it can correct the interfered data packets automatically, so that the reliability & transmission range are improved correspondingly. But without FEC, those date packets can only be dropped.  The module has the function of data encryption & compression. The data of the module transmit in the air features  randomness.  And  with  the  rigorous  encryption  &  decryption, data interception becomes pointless. The function  of  data  compression  can  decrease  the  transmission  time & probability of being interference, while improving the reliability & transmission efficiency. 1.2  Basic usage                                               E32-TTL-100       No.  Usage  Description 1  Transparent transmission Default Module A transmits 01 02 03 to module B, then module B receives 01 02 03.       2  Fixed transmission Module  can  communicate  with  other  modules  in  different  channels,  easy  for networking and repeater. Module A transmits AA BB CC to module B (address: 0x00 01, channel: 0x80), HEX format is 00 01 80 AA BB CC (00 01 refers to the address of module B, 80 refers to the channel of module B), then module B receives AA BB CC (only module B). 3  Broadcast transmission Set the module address as 0xFFFF, then the module can communicate with  other modules in same channel. 4  Power-saving In power-saving mode, the module’s maximum receiving response time is 2000ms, which the average current is below 50uA. 5  Sleep  When the module works in sleep mode, transmitting & receiving is  not available, while the configuration is available. The typical current is 2.0uA in this mode. See more details in related manual about fixed transmission and broadcast transmission.
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module    2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  2  of  14    The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All 1.3  Electrical parameter  E32-TTL-100 No.  Parameter item  Parameter details & Description 1  Size  21 * 36mm, Without antenna and SMA 2  Frequency Band  434MHz 3  Connector  1*7*2.54mm Plug-in 4  Supply voltage  2.3 - 5.5V DC   Note: the voltage higher than 5.5V is forbidden 5  Communication level  UART, USART 6  Operation Range About 3000m Test condition:clear and open area& maximum power,  height:> 2m,air date rate: 2.4kbps 7  Transmitting power  Four optional level(0-3),step by 3dB 8  Air data rate  Default 2.4kbps   Can be configured to 0.3、1.2、2.4、4.8、9.6、19.2kbps 9  Standby current  2.0uA M1=1,M0=1 ( Mode 3 ) 10  Transmitting current  110mA 11  Receiving current  14.5mA(Mode 0 or Mode 1) Minimum 30uA(Mode 2 + 2s wake-up time) 12  Communication interface UART,    8N1、8E1、8O1, Eight kinds of UART baud Rate, from 1200 to 115200 bps 13  Driving mode  UART can be configured to push-pull/high pull, open-drain 14  Transmitting length  512 bytes buffer,58 bytes per package 15  Receiving length  512 bytes buffer,58 bytes per package 16  Address  65536 configurable addresses Easy for network, broadcast and fixed transmission 17  RSSI support  Built-in intelligent processing 18  Sensitivity  -130dbm@0.3kbps Sensitivity has nothing to do with serial baud rate and timing 19  Antenna type  SMA-K   External thread hole, 50 ohm impedance 20  Operating temperature  -40 ~ +85℃ 21  Operating temperature  10% ~ 90% 22  Storage temperature  -40 ~ +125℃
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module    2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  3  of  14    The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All .2.Functional description E32-TTL-100    2.1  Pin definition  E32-TTL-100 Pin No.  Pin item  Pin direction  Pin application 1  M0  Input (weak pull-up)Work with M1 & decide the four operating modes. Floating is not allowed, can be ground. 2  M1  Input (weak pull-up)Work with M0 & decide the four operating modes. Floating is not allowed, can be ground. 3  RXD  Input  TTL UART inputs, connects to external (MCU, PC) TXD output pin. Can be configured as open-drain or pull-up input. 4  TXD  Output  TTL UART outputs, connects to external RXD (MCU, PC) input pin. Can be configured as open-drain or push-pull output 5  AUX  Output To indicate module’s working status & wakes up the external MCU. During the procedure of self-check initialization, the pin outputs low level. Can be configured as open-drain output or push-pull output (floating is allowed).   6  VCC  Power supply 2.3V-5.5V DC 7  GND  Ground 8  Fixing hole  Fixing hole 9  Fixing hole  Fixing hole 10  Fixing hole  Fixing hole ★★★  E32-TTL-100 can be compatible with other E32 series.  ★★★
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module    2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  4  of  14    The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All 2.2  Connect to MCU   E32-TTL-100 No.  Description(STM8L MCU) 1  The UART module is TTL level. 2  For some MCU works at 5VDC, it may need to add 4-10K pull-up resistor for the TXD & AUX pin. 2.3  Reset   E32-TTL-100 No.  Description 1 When the module is powered, AUX outputs low level immediately, conducts hardware self-check and set the operating mode on the basis of the user parameters. During the process, the AUX keeps low level. After the process completes, the AUX outputs high level and starts to work as per the operating mode combined by M1 and A0. Therefore, the user needs to wait the AUX rising edge as the starting point of module’s normal work. 2.4  AUX description   E32-TTL-100 AUX Pin can be used as indication for wireless send & receive buffer and self-check. It can indicate whether there are data that are yet to send through wireless, or whether all wireless data has sent through UART, or whether the module is still in the process of self-check initialization. No.  Description 1 【Indication of UART output】can be used to wake up external MCU.
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module    2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  5  of  14    The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All 2 【Indication of wireless transmitting】 Buffer  (empty):  the  internal  512  bytes  data  in  the  buffer  are  written  to  the  RFIC  (Auto subpackage). When AUX=1, the user can input data less than 512 bytes continuously without overflow. Buffer (not empty): when AUX=0, the internal 512 bytes data in the buffer have not written to the  RFIC  completely.  If  the  user  starts  to  transmit  data  at  this  circumstance,  it  may  cause overtime when the module is waiting for the user date, or transmitting wireless subpackage. Notes: When AUX = 1, it does not mean that all the UART data of the module have been transmitted already, perhaps the last packet of data is still in transmission.  3 【Configuration procedure of module】 Only happened in the process of power-on and exit sleep mode. No.  Notes for AUX 1 For function 1 & function 2 mentioned above, the priority should be given to the one with low level output, which means if it meets each of any low level output condition, AUX outputs low level, if none of the low level condition is meet, AUX outputs high level. 2 When AUX outputs low level, it means the module is busy & cannot conduct operating mode checking. After AUX outputs high level 1ms later, it will complete the mode-switch task. 3 After switching to new operating mode, it won’t be work in the new mode immediately until AUX rising edge 2ms later. If AUX is on the high level, the operating mode switch can be effect immediately. 4  When the user switches to other operating modes from mode 3 (sleep mode) or it’s still in reset process, the module will reset user parameters, during which AUX outputs low level.
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module    2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  6  of  14    The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All .3.Operating mode                                     E32-TTL-100 Contents in below table are the introduction of input status of M1 & M0 and their corresponding mode:   Mode(0-3) M1  M0  Mode introduction  Remark Mode 0 Normal  0  0  UART  and  wireless  channel  is  opened, transparent transmission is on. The receiver must works in mode 0 or mode 1 Mode 1 Wake-up  0  1 UART and wireless channel is opened. The difference between normal  mode and  wake-up mode is it will add preamble code automatically before data packet transmission so that it can awaken the receiver works in mode 2. The receiver can works in mode 0, mode 1 or mode 2. Mode 2 Power-saving 1  0 UART  is  disabled.  Wireless  module  works  at WOR  mode  (wake  on  radio).  It  will  open  the UART and transmit data after receive the wireless data. 1,the  transmitter  must works in mode 1 2,transmitting  is  not allowed in this mode Mode 3 Sleep  1  1  Parameter setting. 3.1  Mode switch    E32-TTL-100 No.  Remarks 1 The user can decide the operating mode by the combination of M1 and M0. The two GPIO of MCU can be used to control the mode-switch. After modifying M1 or M0, it will start to work in new mode 1 ms later if the module is free. If there are any serial data that is yet to finish wireless transmitting, it will start to work in new mode after the UART transmitting finishing. After the module receives the wireless data & transmits the data through serial port, it will start to work in new mode after the transmitting finishing. Therefore, the mode-switch is only workable when AUX outputs 1, otherwise it will delay. 2 For example, in mode 0 or mode 1, if the user inputs massive data consecutively and switches operating mode at the same time, the mode-switch operation is invalid. New mode checking can only be  started  after  all  the  user’s  data  process  completing.  It  is  recommended  that  after  check  AUX pinout status and wait 2ms after AUX outputs high level, then switch the mode. 3 If the module switches from other modes to stand-by mode, it will be work in stand-by mode only after all the remained data process completing. The feature can be used to save power consumption. For example, the transmitter works in mode 0, after the external MCU transmits data “12345”. It can switch to sleep mode immediately but not wait the rising edge of the AUX pin, also the user’s main MCU will go dormancy immediately. Then the module will transmit all the data through wireless transmission & go dormancy 1ms later automatically. Which reduce MCU working time & save power. 4 Likewise, this feature can be used in any mode-switch. The module will start  to work  in new  mode within 1ms after completing present mode task, which enable the user to omit the procedure of AUX inquiry and switch mode swiftly. For example, when switch from transmitting mode to receiving mode, the user MCU can go dormancy in advance of mode-switch, using external interrupt function to get AUX change so that the mode-switch can be done. 5 This operation is very flexible and efficient. It is totally designed  on  the  basis of  the  user  MCU’s convenience, at the same time reduce the whole system work load as much as possible, increase the efficiency of system work and reduce power consumption.
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module    2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  7  of  14    The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All 3.2  Normal mode(Mode 0)     E32-TTL-100 When M1 = 0 & M0 = 0, module works in mode 0 Transmitting The module can receive the user data from serial port, and transmit  wireless  data package which length is 58 bytes. When the data inputted by user is up to 58 byte, the module  will  start  wireless  transmission.  During  which  the  user  can  input  data continuously for transmission. When the required transmission bytes is less than 58 byte, the module will wait 3-byte time and treat it as data termination unless continuous data inputted by user. Then the module will transmit all the data through wireless channel. When the module receives the first data packet from user, the AUX outputs low level. After the module transmit all the data into RF chip & start transmission, AUX outputs high level. At this time, it means that the last wireless data package transmission has started, which enable the user to input another 512 bytes continuously. The data package transmitted from the module works in mode 0 can only be received by the module works in mode 0 or 1. Receiving The  module  keeps  the  wireless  receive  function  on,  it  can  receive the data packet transmitted  from  the  module  works  in  mode  0  &  mode  1.  After  receiving the data packet, the AUX outputs low level, 5ms later the module starts to transmit wireless data through serial port TXD pin. After all the wireless data have been transmitted via serial port, the module AUX outputs high level. 3.3  Wake-up mode(Mode 1)   E32-TTL-100 When M1 = 0 & M0 = 1, module works in mode 1. Transmitting The condition of data packet transmission & AUX function is the same as mode 0. The only  difference  is  that  the  module  will  add  preamble  code  before  each  data  packet automatically. The preamble code length depends on the wake-up time set in the user parameters. The purpose of the preamble code is waking up the receiving module works in mode 2.  Therefore, the data  package transmitted from mode  1 can  be received by mode 0, mode1 and mode 2. Receiving  The same as that in mode 0. 3.4  Power-saving mode(Mode 2)      E32-TTL-100 When M1 = 1 & M0 = 0, module works in mode 2. Transmitting  UART is closed, the module cannot receive any serial port data from outside MCU. Hence the module works in this mode does not have the function of wireless transmission. Receiving In mode 2, it is required the date transmitter works in mode 1. The  wireless  module  monitors  the  preamble  code  at  regular  time.  Once  it  gets  the preamble code, it will remain as receive status and wait for the completion of the entire valid date package receives. Then the module lets the AUX outputs low level, 5ms later opens the serial port to transmit received wireless data through TXD. Finally AUX outputs high level after process completing.
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module    2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  8  of  14    The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All The wireless module stays in “power-saving – monitoring” working status (polling). By setting different wake-up time, the module can have different receive response delay (2s maximum) and average power consumption (30uA minimum). The user needs to achieve a balance between communication delay time & average power consumption. 3.5  Sleep mode (Mode 3)     E32-TTL-100 When M1=1,M0=1,module works in mode 3 Transmitting  N/A Receiving  N/A Parameter setting This  mode  can  be  used  for  parameter  setting.  It  uses  serial  port  9600  &  8N1  to  set module working parameters through specific instruction format. (pls refer to parameters setting for details) Notes When the mode changes from stand-by mode to others, the module will  reset  its parameters, during which the AUX keeps low level and then outputs high level after reset completing. It is recommended to check the AUX rising edge for user. 3.6  Quick communication test    E32-TTL-100 Steps  Operation 1 Plug the USB test board (E15-USB-T2) into computer, make sure the driver is installed correctly. Plug mode-select jumper in the USB test board (M1 = 0,M0 = 0), make the module work in mode 0. 2  Optional power supply, 3.3V or 5V. 3  Operate AccessPort software and select the correct serial port code. See figure 7.
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module    2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  9  of  14    The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All .4.Instruction format     E32-TTL-100 In sleep mode(mode 3:M1=1, M0=1), it supports below instructions on list. (Only support 9600 and 8N1 format when setting) No.  Instruction format  Illustration 1  C0 + working parameters C0 + 5 bytes working parameters are sent in hexadecimal format. 6 bytes in total and must send in succession. ( Save the parameters when power-down ) 2  C1    C1    C1  Three C1 are sent in hexadecimal format. The module returns the saved parameters and must send in succession.   3  C2 + working parameters C2 + 5 bytes working parameters are sent in hexadecimal format. 6  bytes  in  total  and  must  send  in  succession.  (  Not  save  the parameters when power-down ) 4  C3    C3    C3  Three C3 are sent in hexadecimal format. The module returns the version information and must send in succession. 5  C4    C4    C4  Three C4 are sent in hexadecimal format. The module will reset one time and must send in succession. 4.1  Default parameter    E32-TTL-100 Default parameter values:C0 00 00 1A 17 44 Model  Frequency  Address  Channel Air data rate Baud rate Parity E32-TTL-100  434MHz  0x0000  0x17  2.4kbps  9600  8N1 4.2  Parameter setting instruction      E32-TTL-100 The difference between C0 command and C2 command is that C0 command will write parameters into the internal flash memory and can be saved when power down, while C2 command cannot be saved when power down, because C2 command is temporarily mend instruction. C2 is recommended for the occasion that need to change the operating parameters frequently, Like C2 00 00 1A 17 44. No.  Item  Description  Remark 0  HEAD  Fix 0xC0 or 0xC2, it means this frame data is control command Must be 0xC0 or 0xC2 C0: Save the parameters when power-downC2: Not save the parameters when power-down 1  ADDH  High address byte of module (the default 00H) 00H-FFH 2  ADDL  Low address byte of module (the default 00H) 00H-FFH
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module      2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  10  of  14      The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All 3  SPED  Rate parameter,including UART baud rate and air date rate 7,6      UART parity bit   00:8N1(default)   01:8O1   10:8E1   11:8N1(equal to 00) ------------------------------------------ 5,4,3   TTL UART baud rate(bps)   000:1200bps   001:2400bps   010:4800bps   011:9600bps(default)   100:19200bps   101:38400bps   110:57600bps   111:115200bps ------------------------------------------ 2,1,0   Air date rate(bps)   000:0.3Kbps   001:1.2Kbps   010:2.4Kbps(default)   011:4.8Kbps   100:9.6Kbps   101:19.2Kbps   110:19.2Kbps   111:19.2Kbps UART mode can be different betweencommunication parties----------------------------------------------- UART baud rate can be differentbetween communication partiesThe UART baud rate has nothing to dowith wireless transmission parameters& won’t affect the wireless transmit /receive features.---------------------------------------------- The lower the air date rate, the longerthe transmitting distance,    betteranti-interference performance andlonger transmitting timeThe air date rate must keep the samefor both communication parties.4  CHAN  7,6,5:  N/A ------------------------------------------ 4-0:Communication channel, default 17H(434MHz) 0(recommended)-------------------------------------------------00H-1FH 5  OPTION  7,    Fixed transmission(similar to MODBUS)    0: Transparent transmission mode(default)  1: Fixed transmission mode ------------------------------------------ 6     IO drive mode(the default 1)    1:TXD and AUX push-pull outputs,   RXD pull-up inputs  0:TXD、AUX open-collector In fixed transmission mode, the firstthree bytes of each user's data framecan be used as high/low address andchannel. The module changes itsaddress and channel when transmit.And it will revert to original settingafter complete the process.----------------------------------------------- This bit is used to the module internalpull-up resistor. It also increases thelevel’s adaptability in case of opendrain. But in some cases, it may needexternal pull-up resistor.
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module      2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  11  of  14      The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All outputs, RXD open-collector inputs ---------------------------------------- 5,4,3   wireless wake-up time(for the receiver, it means the monitor interval time ,while for the transmitter it means continuously sending preamble code time.)   000:250ms(default)   001:500ms      010:750ms      011:1000ms       100:1250ms        101:1500ms        110:1750ms       111:2000ms    ----------------------------------------- 2,      FEC switch   0:Turn off FEC   1:Turn on FEC(Default) ----------------------------------------- 1, 0      transmission power (approximation) ----------------------------------------------- The transmit & receive module work inmode 0, whose delay time is invalid &can be arbitrary value.The transmitter works in mode 1 cantransmit the preamble code of thecorresponding time continuously.When the receiver works in mode 2,the time means the monitor intervaltime (wireless wake-up). Only the datafrom transmitter that works in mode 1can be received.The wake-up time set by transmittercannot be less than the monitorinterval time of receiver; otherwise, itmay lead to data loss. In case oftwo-way communication, both partiesshould keep the wake-up time thesame.The longer the wake-up time, thelower the average receive currentconsumption.------------------------------------------------After turn off FEC, the actual datatransmission rate increases whileanti-interference ability decreases.Also the transmission distance isrelatively short.Both communication parties mustkeep on the same pages aboutturn-on or turn-off FEC.----------------------------------------------- The external power must make surethe ability of current output more than200mA and ensure the power supplyripple within 100mV.Low power transmission is notrecommended due to its low powersupply efficiency.
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module      2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  12  of  14      The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All For example: The meaning of No.3 "SPED" byte: The binary bit of the byte  7  6  5  4  3  2  1  0 The specific value (user configures)  0  0  0  1  1  0  1  0 Meaning  UART parity bit 8N1  UART baud rate is 9600  Air date rate is 2.4kCorresponding hexadecimal  1  A 4.3  Reading operating parameters    E32-TTL-100 Instruction format  Description C1+C1+C1 In sleep mode(M0=1,M1=1), User gives the module instruction (HEX format): C1 C1 C1, Module returns the present configuration parameters.   For example, C2 00 00 1A 17 44. 4.4  Reading version number   E32-TTL-100 Instruction format  Description C3+C3+C3 In sleep mode(M0=1,M1=1), User gives the module instruction (HEX format): C3 C3 C3, Module returns its present version number, for example C3 32 xx yy. 32 here means the module model (E32 series); xx is the version number  and yy refers to the other module features. 4.5  Reset instruction    E32-TTL-100 Instruction format  Description C4+C4+C4 In sleep mode(M0=1,M1=1), User gives the module instruction (HEX format): C4 C4 C4, the module resets for one time. During  the  reset  process,  the  module  will  conduct  self-check,  AUX outputs low level. After reset completing, the AUX outputs high level, then the module starts to work regularly which the working mode can be switched or be given  another instruction.
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module      2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  13  of  14      The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All .5.Parameter setting     E32-TTL-100    Step  Operation  Description 1  Install Driver  Please install the USB adapter driver (CP2102). 2  Pull out the jumper Pull the M0、M1 jumper out, see figure 9 3.3V or 5V are available for jumper. 3  Connect to module Connect the module with USB adapter. Connect to the USB interface of PC. 4  Open serial port Operate the parameter setting software, choose corresponding serial number and press the “Open CommPort” button. Please choose other serial numbers until open successfully. 5  Interface Press“Press to Read”button,the interface will be as figure 9 If failed, please check if the module is in mode 3, or the driver has been installed or not. 6  Input parameter Please adjust the parameter as your request according to the corresponding setting, then click “Write” button, write the new parameter to the module 7  Complete the operation. Please operate the “Fifth step” if you need to reconfigure, if the configuration is completed,   Please click "close UART" and then take off the module. 8  Commands Configuration  Parameter configuration is also available for MCU (in mode 3). 434MHz
E32-TTL-100 Datasheet V1.0     Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046        Website: www.cdebyte.com Professional R&D RF Module      2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  14  of  14      The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All FCC StatementThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement  This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2ALPH-E32-TTL-100 Or Contains FCC ID: 2ALPH-E32-TTL-100” when the module is installed inside another device, the user manual of this device must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate theequipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product
E32-TTL-100 Datasheet V1.0                                       Chengdu Ebyte Electronic Technology Co., Ltd. Purchase the sample:http://www.aliexpress.com/store/2077046                     Website: www.cdebyte.com Professional R&D RF Module         2.4G、915M、868M、780M、490M、434M、315M、230M、170M Wireless Module Page  15  of  14         The copyright and the product has the Chengdu Ebyte Electronic Technology Co., Ltd. All .6.About us                                           E32-TTL-100       Chengdu Ebyte Electronic Technology Co., Ltd is a high-tech company, focus on wireless transmission. Our company owns a  number of  independent  research & development products and  obtain unanimously approved customers. With powerful R&D team, our company can provide customers with perfect After-sales service and technical assistance.  【Website】:www.cdebyte.com  1111          【Aliexpress】:http://www.aliexpress.com/store/2077046 【Address】: Innovation Center D347,4# XI-XIN road, High-tech district(West),Chengdu, Sichuan, China 【Contact person】:chenfang@cdebyte.com   Elaine      【Contact person】:fanjuan@cdebyte.com    Maggie     【Technical support】:support@cdebyte.com

Navigation menu