Chiayo Electronics Co M-1002 Wireless Microphone Transmitter User Manual

Chiayo Electronics Co Ltd Wireless Microphone Transmitter

User Manual

R-1001/R-2001Q-1 0O1/Q-1 Q02/M-1 0O1/M-1 002Operating ManualCHIAYO ELECTRONICS CO.. LTD.
--- J~GENERALR-1001/ R-2001 is a VHF high-band non-diversity system with quartz controlledfixedfrequency design. The receiver must be combined with Chiayo's Q- and M-series of wireless microphone.COMPOSITION1. MAINFRAME:R-1001/ R-20012. ACCESSORIES:1)ACadapter 2)antennaX 1(R-1001) /antenna X 2(R-2001)3)Outputcable / PHONE 4)OperatingmanualCOMBINATION1. MATCHINGWIRELESS MICROPHONE:Q- and M- series such as Q-1001 &M-1001CONTROLS AND FUNCTIONSFRONT PANELREAR PANELsCONTROLS AND FUNCTIONSI.POWER SWITCH AND VOLUME CONTROLTurn the knob clockwise until it clicks to switch on the power. Further turning will incre-ase the volume.<..POWER ON INDICATORWhen power is switched on ' the power on LED will light up.3 .RF SIGNAL INDICATORIndicates RF signal received. As soon as signal is emitted from the microphone' theLED of the indicator will light up.4.AF SIGNAL INDICATORIndicates the audio signal. When sound is applied to microphone' LED will light up.5.ANTENNA INPUT JACK(R-1001)For direct mounting of antenna or antenna extension cable.6 .UNBALANCED AUDIO OUTPUT JACK7 .SO CONTROLmuting level can be adjusted by SO control.8 DC POWER SUPPLY INPUT SOCKETA 12-15V external DC power supply or an AC adapter could be connected to this socketwhile the negative is grounded.9 .CH2 VOLUME CONTROL(R-2001)to.ANTENNA 1 INPUT JACK (R-2001)11.ANTENNA 2 INPUT JACK (R-2001)HAND-HELD Microphone (Q-1001)1.The microphone is shown in Fig 1.Windscreen and capsule setBattery status indicator~Fig. 1.Transmitter electronics Battery compartment.: Wireless Microphone2.To access to the battery compartment, loosen the battery pack in counter clockwisedirection, as shown in Fig. 2.Fig. 2.3. Insert one piece of 9V battery with correct polarity, as shown in Fig. 3. Beforeinserting the battery, make sure that the power switch is switched off.Fig. 34. After putting the battery cover back to the housing, slides the switch to "ON"position as shown in Fig. 4.~Fig. 4.:5.As soon as the switch is on, the battery-status indicator will give a flash, indicatinga normal operation. If there is no flash, it indicates either power supply is notavailable or battery is installed wrongly.6.After switching on, the RF signal indicator LED(s) of matching receiver will light up,indicating the microphone signal transmission is in normal operation.7.Switch off the power switch when the microphone is not in use, meanwhile, removethe battery out of microphone if it is not in use for an extended period.
HAND-HELD Microphone (Q-1002)Handheld MicrophoneParts and FunctionsBattery statusLED indicatorIBattery compartmentcoverFig.1Metal Grille( Capsule module inside)Power SwitchBattery InstallationQ-802 uses 1 piece of 9V battery. To install new or replace the old battery, First unscrew the battery capfrom the battery compartment, then insert the new battery according toits correct polarity as indicated. For longerOperation hour, Alkaline batteryis recommended! ..,.Fig.2After putting the battery cover back to the housing, slides the switch to "ON"position as shown in Fig. 3.Fig.3As soon as the switch is on, the battery-status indicator will give a flash, indicatinga normal operation. If there is no flash, it indicates either power supply is notavailable or battery is installed wrongly.After switching on, the RF signal indicator LED(s) of matching receiver will light up,indicating the microphone signal transmission is in normal operation.Switch off the power switch when the microphone is not in use, meanwhile, removethe battery out of microphone if it is not in use for an extended period._JBelt-Pack Transmitter(M-1 001)J1.The Belt-Pack transmitter is shown in Fig.1.b II I I .d.I-c Flash: normala ery s a us In Ica or Red: battery IowJ)FEMALE ConnectorBattery packIDlavalier MicrophoneMike clip2.To access the battery ,pull out the battery cover as in Fig.2.IJIim83.lnsert a 9V battery with correct polarity into the battery compartment and put backthe compartment cover, as show in Fig.3.4.mEmID
--- - 1-----------4.Sliding the power switch of the transmitter control panel to"ON" position, as show in Fig.?, the battery status indicatorgives a flash to indicate a normal operation. If there is no flash,it indicates either power supply is not available or battery isinstalled wrongly. If the indicator keeps lighting, it indicatesthat battery is weak, a replacement is necessary.--ConnectorBelt-Pack Transmitter(M-1002)Parts & FunctionsPower SwitchBattery statusindicator.MIC cableLED Batterystatus Indicator AntennaPower Switch5.The pin arrangement of the transmitter's connector jack isshown in Fig.6. A unique feature of the M-303 is its seperatehigh / Iow impedance and bias with the same jack for ECM input.You could properly match the high impedance inputsignals such as electric guitar, or Iow impedance input signalssuch as dynamic microphone, then choose the proper inputconnecting cable and plug correctly, as shown in Fig.7, 8, and 9 .Belt-Pack TransmitterFig. 7Connecting CableInput Plug Phone PlugIII High Impedance Input for Electric GuitarFig. 8Connecting CableInput Plug Cannon PlugIII LOW IMPEDANCE INPUT FOR DYNAMIC MICROPHONEuBatterycompartmentFig.7Belt clip( hidden behind)lli lDDANTEl VDC.. .. S,"GACThreaded Mini Plug(STEREO)MIC capsuleMIC clip Fig.1Connecting CableInput Plug ECM CapsuleIII With Bias Input 1o. ECMFig. 6Battery InstallationM-1002 uses 1 piece of 9V battery. To install new or replace the old battery, firstopen the battery compartment cover, then insert the new battery according to itscorrect polarity as indicated. For longer operation hour, Alkaline battery isrecommended!6.After switching on, the RF signalindicator LED( s) of matchingreceiver will light up , indicatingthe microphone signal transmis-sion is in normal operation.Fig.37 .Switch off the power when themicrophone is not in use, mean-while remove the battery out ofmicrophone if it is not in use foran extended period..!Ill~Fig.2Belt ClipThis uniquely designed belt clip allows 360 rotation. Select the best positionto achieve optimum wearing comfort.Caution: The audio cable serves as antenna for this VHF system. Please stretch thecable to its maximum to get the most efficient transmission power.m3600 rotate ablebelteljp.Fig.5Fig.4
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help. FCC Caution : To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
--CHIA YOhttp:liwww.chlayo.com.tw E.-mail:sales@chiayo.com.twOFFICE: 30. LANE 27, SECA. JEN-AL ROAD, T!\IPEL TAIWANiTEL 886-2-2741-5741FACTORY:88, CHUNG HSIAO STREET 2, CI--ilAYI,TAIWAN, ITEL: 886-5-271-1000Printed in Taiwan, Jan 2004FAX: 886--2-2752-5242FAX 886-5-276-7611121390

Navigation menu