ChipSiP Technology CWFB211-XXX 5G +2.4G 2T/2R WLAN FMC User Manual rev01

ChipSiP Technology Co.,Ltd. 5G +2.4G 2T/2R WLAN FMC rev01

Contents

User manual

 CWFB211-XXX Specification Revision 01 2012/09/12 Prepared By: Jeff Hsieh
RevisionHistoryRevisionDateNotesOwner01 2012/09/12 Initial Release Jeff Hsieh     
1.WirelessSpec.WLAN: 2X2 MIMO Wi-Fi Frequency Range (MHz) Channels Peak Rated Power Modulation Technology 802.11b 2412 – 2462(DTS) 11 19.52dBm DSSS 802.11g 2412 – 2462(DTS) 11 23.87dBm DSSS, OFDM 802.11n HT20 2412 – 2462(DTS) 11 23.77dBm OFDM HT40 2422 – 2452(DTS) 7 23.71dBm 802.11a 5180 – 5240(NII) 4 9.19dBm OFDM 5745 – 5825(DTS) 5 23.88dBm 802.11n HT20 5180 – 5240(NII) 4 8.65dBm OFDM HT20 5745 – 5825(DTS) 5 24.81dBm HT40 5190 – 5230(NII) 2 10.93dBm HT40 5755 – 5795(DTS) 2 24.60dBm Modulation type CCK, DQPSK, DBPSK for DSSS 64QAM. 16QAM, QPSK, BPSK for OFDM Transition Rate: Upto 300Mbps
Antenna Designation: Manufacturer Model No. Connector Type Type Gain (2.4GHz) Gain (5GHz)Ant 1 Airwave Technologies INC. EDA-8709-25GR2-A4-RM Revise SMA, unique Dipole Ant 2 dBi 2 dBi Ant 2 ARISTRTLE RFA-25-C2S1-70-90 unique Dipole Ant 2 dBi 2 dBi Ant 3 Tranwo technology corp. SD001-201003-A101 Revise SMA, unique Dipole Ant 2dBi 2 dBi Ant 3-1 Tranwo technology corp. RFA-05-2-L14M3-B70-1 Revise SMA, unique Dipole Ant 2dBi 2 dBi Ant 3-2 Tranwo technology corp. 202-000442-00 unique Patch Ant 0 dBi -1 dBi Ant 3-3 Tranwo technology corp. 202-000441-00 unique Patch Ant 0.5 dBi -0.5 dBiAnt 4 UDM Group Technology Co., Ltd 26-52-01800G unique PCB Ant (Green) 2.5 dBi 4 dBi Ant 5 Unictron Technologies Corporation H2P566WKBA0100 unique PCB Ant (Blue) 2.3 dBi 4dBi This antenna list table could be used for CWFB211-XXX.. The max gain of 2.4G: 2.5dBi. The max gain of 5G: 4dBi. 
Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Statement: This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter and this equipment should be installed and operated with minimum distance 20cm between the radiator & your body. When suing IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15 to 5.25GHz frequency range. The FCC requires this product to be used indoors for the frequency range of 5.15 to 5.25GHz to reduce the potential for harmful interference to co channel mobile satellite systems. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove. This RF module in the user’s manual of the end product which integrates this module. The user’s manual for OEM Integrators must include the following information in a prominent location End Product Labeling: The final end product must be labeled in a visible area with the following: “Contains FCC ID: O7N-CWFB211-XXX”.

Navigation menu