Chris King R45D Addendum User Manual

User Manual: Chris King R45D-Addendum

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

R45 Disc Centerlock Hub Addendum
Centerlock rotor mounting system licensed by Shimano®
Centerlock is a proprietary mounting system that requires a Shimano®
lockring to complete installation of rotor. Chris King R45 Disc Centerlock
hubs are compatible with the following Shimano® lockrings:
Compatible Lockrings
- Front (Y8K198010) – Typically supplied with genuine Shimano rotor. Or
(Y26N98030) – Typically sold as an after market part, also available direct
through Chris King under part number PHB355
- Rear (Y26N98030) – Typically sold as an after market part, also available
direct through Chris King under part number PHB355

Centerlock Rotor Installation:
Front Hubs:
Please follow rotor manufacturer’s installation instructions.
Rear Hubs:
Before installing the rear Centerlock rotor the adjusting clamp must be
removed. Follow steps below for removal, installation and setting hub
preload.
Clamp Removal:
1. Loosen 2.5mm hex bolt on adjusting clamp and then remove R45 QR
Insert from main axle assembly by pulling it directly out of the non-driveside of axle. [Note: If the QR Insert is difficult to remove by hand, insert
a long P-Handle or L-shaped 5mm hex wrench into the driveside of the
axle. The QR Insert should remove with a light tap to the exposed hex
wrench from a plastic or rubber mallet.]
2. Unscrew adjusting clamp and remove it from axle. By pulling onto the
adjusting clamp, once free from the threads will also remove steel axle
end caps on thru axle assemblies.
[Note: If the Axle End Cap is difficult to remove using only the adjusting

clamp, use a small flat- head screwdriver and insert it into the Axle End
Cap slot, twist the screwdriver and the Axle End Cap should come off
with the screwdriver.]
3. At this point the Centerlock rotor (or Centerlock to 6-bolt adapter) can
be installed. Make sure to follow rotor manufacturer’s instructions. (Use
Shimano Y26N98030/ Chris King#PHB355 Lockring on rear hubs)
Clamp Install:
1. Thread adjusting clamp onto the protruding threads on the non-driveside of axle.
2. On QR axles, insert R45 QR insert into non-driveside axle end. On
142mm x 12mm thru axles, ensure steel axle end cap is snapped onto
axle by pressing the axle end cap by hand.
3. Snug adjusting clamp up to bearing.

Rear Hub Adjustment:
The R45D Centerlock rear hub features an adjusting clamp and bearing
spacer spring that maintain proper bearing preload and seating.
1. Secure the hub/wheel into the bike or truing stand with quick release
or frame thru axle system.
2. Push the hubshell toward the driveside. This compresses the bearing
spacer spring in the driveshell and ensures proper bearing seating.
3. While maintaining pressure on the hubshell, tighten the adjusting
clamp onto axle until it stops against bearing. Do not over tighten.
4. Once adjusting clamp is in position, tighten adjusting clamp with a
2.5mm hex key to 10 inch- pounds (1.13 Nm).
5. Double check adjustment by attaching wheel to bicycle frame. Check
for bearing play or binding, and readjust adjusting clamp if needed.

Questions? Please e-mail us at info@chrisking.com or call Customer Service at 800-523-6008

R45 Disc Centerlock Front Hub Assembly

R45 Disc Centerlock Rear Hub Assembly
SHIMANO 11SPD COMPATIBLE

***REQUIRES SHIMANO®
Y26N980830 - 15/20 DISC LOCKRING
(PHB355) - CHRIS KING PART#

(



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c014 79.156797, 2014/08/20-09:53:02
Create Date                     : 2016:06:27 10:56:46-07:00
Metadata Date                   : 2016:06:27 10:56:55-07:00
Modify Date                     : 2016:06:27 10:56:55-07:00
Creator Tool                    : Adobe InDesign CC 2014 (Macintosh)
Instance ID                     : uuid:bbfedf8f-4953-9248-b05b-9fb30494c81c
Original Document ID            : xmp.did:c50efe12-f756-48ff-a23a-2cbc21495f4f
Document ID                     : xmp.id:8dc0ec98-063d-4063-9d57-7a9e2e898001
Rendition Class                 : proof:pdf
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2014 (Macintosh)
History Changed                 : /
History When                    : 2016:06:27 10:56:46-07:00
Derived From Instance ID        : xmp.iid:53ebec4b-8704-4e57-9d12-8066e82bec94
Derived From Document ID        : xmp.did:c50efe12-f756-48ff-a23a-2cbc21495f4f
Derived From Original Document ID: xmp.did:c50efe12-f756-48ff-a23a-2cbc21495f4f
Derived From Rendition Class    : default
Format                          : application/pdf
Producer                        : Adobe PDF Library 11.0
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CC 2014 (Macintosh)

EXIF Metadata provided by EXIF.tools