Chungear Co CE10320 CEILING FAN REMOTE CONTROLLER (TRANSMITTER) User Manual

Chungear Industrial Co Ltd CEILING FAN REMOTE CONTROLLER (TRANSMITTER)

User Manual

CEILING FAN REMOTE CONTROLLEROPERATION AND INSTALLATION INSTRUCTIONS(Please keep this instruction pamphlet.)IMPORTANT POINTS TO REMEMBER:1.Read and save these instructions.2.Please note that all fixed wiring appliances should be installed by a qualified electrician.3.The supply to the remote control receiver should be connected through a mains switch, i.e. existing wallswitch.4.Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.5.Install receiver into the ceiling fan canopy of the fan to ensure proper protection.6.This unit is to be used for the control of ceiling fan and in a AC110/120V 60Hz power supply only.7.Do not install in damp locations or immerse in water. (For indoor use only.)8.Do not pull on or cut leads shorter.9.Do not drop or bump the unit.10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes placeas this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach ofchildren.11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable(rheostat) wall control.INSTALLATION INSTRUCTIONS1.Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the “Light Switch”after installation.2.Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopycomes up to cover the receiver and bracket.IMPORTANTYOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT KIT(IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL.CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
CODE SWITCH1.CODE SWITCH: Codes are set by pushing dip switches up or down. It is imperative that the code usedfor both transmitter and receiver is exactly the same, otherwise remote controller will not work. Pleasenote the code switch will enable you to operate a second remote controller independently. For example, ifyou have two ceiling fans with 2 remote control units, set 2 different codes for each set oftransmitter/receivers. This means you can operate each ceiling fan independently.2.Your remote control is ready for use after battery installation.FUNCTIONS OF TRANSMITTER POWERPOWER : Turn on or off the fan and light. or light 30s dealy. FAN SPEEDFAN SPEED : Turn on the fan at high ,med,low speed,or fan off. LIGHT1/f :The fan will turn at natural wind mode 1/fTIMER:The fan will turn off after 2 or 4 or 8 hours. TIMERLIGHT:Press and release immediately to turn on or off the light.Press and hold to dim or brighten lights to the desiredlevel and release.FAN AUTO: The fan will run in automatic modeUP: Increase the value of temperatureDOWN: decrease the value of temperatureCeiling Fan Remote ControlWiring ConnectionInstallation of TransmitterWall Mount Holder withtwo screws.TR222A
CAUTION: To assure continued FCC compliance: FCC ID：KUJCE10320 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. IC This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. French: Cet appareil radio est conforme au CNR-210 d’Industrie Canada. L’utilisation de ce dispositif est autorisée seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.

Navigation menu