Chungear Co CE10320 CEILING FAN REMOTE CONTROLLER (TRANSMITTER) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2489285
Application ID	6XaSX7MNLSbT7kZUzmO8aw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	55.1kB (688709 bits)
Date Submitted	2014-12-31 00:00:00
Date Available	2014-12-31 00:00:00
Creation Date	2014-12-12 17:59:40
Producing Software	doPDF Ver 7.3 Build 382 (Windows XP Professional Edition (SP 3) - Version: 5.1.2600 (x86))
Document Lastmod	2014-12-23 11:44:12
Document Title	User Manual

CEILING FAN REMOTE CONTROLLER
OPERATION AND INSTALLATION INSTRUCTIONS
(Please keep this instruction pamphlet.)
IMPORTANT
YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT KIT
(IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL.
IMPORTANT POINTS TO REMEMBER:
1.Read and save these instructions.
2.Please note that all fixed wiring appliances should be installed by a qualified electrician.
3.The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall
switch.
4.Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.
5.Install receiver into the ceiling fan canopy of the fan to ensure proper protection.
6.This unit is to be used for the control of ceiling fan and in a AC110/120V 60Hz power supply only.
7.Do not install in damp locations or immerse in water. (For indoor use only.)
8.Do not pull on or cut leads shorter.
9.Do not drop or bump the unit.
10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place
as this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach of
children.
11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable
(rheostat) wall control.
INSTALLATION INSTRUCTIONS
CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
1.Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the “Light Switch”
after installation.
2.Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopy
comes up to cover the receiver and bracket.
CODE SWITCH
1.CODE SWITCH: Codes are set by pushing dip switches up or down. It is imperative that the code used
for both transmitter and receiver is exactly the same, otherwise remote controller will not work. Please
note the code switch will enable you to operate a second remote controller independently. For example, if
you have two ceiling fans with 2 remote control units, set 2 different codes for each set of
transmitter/receivers. This means you can operate each ceiling fan independently.
2.Your remote control is ready for use after battery installation.
FUNCTIONS OF TRANSMITTER
POWER : Turn on or off the fan and light. or light 30s dealy.
FAN SPEED : Turn on the fan at high ,med,low speed,or fan off.
POWER
FAN SPEED
LIGHT
1/f :The fan will turn at natural wind mode
1/f
TIMER:The fan will turn off after 2 or 4 or 8 hours.
LIGHT:Press and release immediately to turn on or off the light.
Press and hold to dim or brighten lights to the desired
level and release.
FAN AUTO: The fan will run in automatic mode
UP: Increase the value of temperature
DOWN: decrease the value of temperature
TIMER
Ceiling Fan Remote Control
Wiring Connection
TR222A
Installation of Transmitter
Wall Mount Holder with
two screws.
CAUTION:
To assure continued FCC compliance:
FCC ID：KUJCE10320
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the grantee of this device could void the
user's authority to operate the equipment.
IC
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment.
French: Cet appareil radio est conforme au CNR-210 d’Industrie Canada. L’utilisation de
ce dispositif est autorisée seulement aux deux conditions suivantes : (1) il ne doit pas
produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif. Cet équipement est conforme aux limites d’exposition aux
rayonnements IC établies pour un environnement non contrôlé.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Page Mode                       : UseNone
XMP Toolkit                     : 3.1-702
Create Date                     : 2014:12:12 17:59:40+08:00
Modify Date                     : 2014:12:23 11:44:12+08:00
Metadata Date                   : 2014:12:23 11:44:12+08:00
Producer                        : doPDF Ver 7.3 Build 382 (Windows XP Professional Edition  (SP 3) - Version: 5.1.2600 (x86))
Format                          : application/pdf
Document ID                     : uuid:1da02aea-d085-4d15-b06c-2d98e23185f1
Instance ID                     : uuid:34320611-c39d-4289-93ce-5e0ed90fb859
Page Count                      : 3
Page Layout                     : OneColumn

EXIF Metadata provided by EXIF.tools