Chungear Co CE10405 CEILING FAN REMOTE CONTROLLER (TRANSMITTER) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2899083
Application ID	DcXcxVAfPhFpjHwz8XP2zQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	49.64kB (620508 bits)
Date Submitted	2016-02-08 00:00:00
Date Available	2016-02-08 00:00:00
Creation Date	2015-11-03 16:07:23
Producing Software	doPDF Ver 7.3 Build 382 (Windows XP Professional Edition (SP 3) - Version: 5.1.2600 (x86))
Document Lastmod	2016-01-29 11:03:19
Document Title	User Manual

WALL TRANSMITTER
OPERATION AND INSTALLATION INSTRUCTIONS
(Please keep this instruction pamphlet.)
IMPORTANT
YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED LIGHT KIT ON
POSTION BEFORE OPERATING REMOTE CONTROL.
IMPORTANT POINTS TO REMEMBER:
1. Read and save these instructions.
2. Please note that all fixed wiring appliances should be installed by a qualified electrician.
3. The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall
switch.
4. Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.
5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection.
6. This unit is to be used for the control of ceiling fan and in an AC110/120V 60Hz power supply only.
7. Do not install in wee locations or immerse in water.
8. Do not pull on or cut leads shorter.
9. Do not drop or bump the unit.
10. AC 110/120V 60HZ power for transmitter.
11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable
(rheostat) wall control.
INSTALLATION INSTRUCTIONS
CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
1. Ceiling fan must be set at HIGH speed after installation.
2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopy
comes up to cover the receiver and bracket. (FIG 1, 2 and 3)
ACTIVATING THE LEARNING PROCESS
1. After installation is complete, AC power is turned on
and
SWITCH is at ON position within 30
seconds, press and hold the LEARN button for 3
seconds. The receiver will make sound, Bi, once. This
will indicate the receiver has learned the ID that was
previously selected on the transmitter. then the wall
TR228A
transmitter can control the receiver.
2. If user cannot finish the setting within the 30 seconds
FIG. 4
time frame,
the main power must be turned off and re-started again. This will reset
the unit. Repeat step 1 until the LEARNING feature is activated as indicated.
TRANSMITTER
WALL TRANSMITTER OPERATION (FIG.5)
While the fan is on, Press this button to increasing fan speed
(1~6speed).
While the fan is on,Press this button to decreasing fan speed (1~6
speed).
Press this button to turn the fan on or off.
TR228A
Press this button to set fan wind direction up or down.
FIG5
ON/OFF—Press this button and release instantly to turn on or off the light.
DIMMER—Press and hold to dim or brighten lights to the desired level and release.
(Tungsten bulb only)
AC POWER ON/OFF SWITCH, Slide to left to set power off, Slide to right to set power on.
LED indicator，When pressing remote button, the LED indicator on position 1 would
be on. When press fan speed button, the LED indicator on position 2~7 would be on( 1~6 speed).
Installing Wall Control (TRANSMITTER):
Remove wall plate, disconnect and remove the toggle switch
from wall junction box. Using the wire connectors,
make the electrical connections to the wall control
(transmitter) unit. Carefully push all connected wires
inside wall switch box. Secure wall control unit with
2 screws previously removed. Face plate could be screwed
onto the transmitter.
To assure continued FCC compliance:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect
the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or
an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to
operate the equipment.
FCC ID：KUJCE10405
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
IC
This device complies with Industry Canada license‐exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
French:
Cet appareil radio est conforme au CNR‐247 d’Industrie Canada. L’utilisation de ce dispositif
est autorisée seulement aux deux conditions suivantes : (1) il ne doit pas produire de
brouillage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage
radioélectrique reçu, même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum
de 20 cm de distance entre la source de rayonnement et votre corps.
FCC ID Label(有做Part 15B DOC的產品才能有FCC LOGO)
FCC ID: U6OCA012(待)
FCC ID Label(沒有做Part 15B DOC的產品不能有FCC LOGO)

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Page Mode                       : UseNone
XMP Toolkit                     : 3.1-702
Create Date                     : 2015:11:03 16:07:23+08:00
Modify Date                     : 2016:01:29 11:03:19+08:00
Metadata Date                   : 2016:01:29 11:03:19+08:00
Producer                        : doPDF Ver 7.3 Build 382 (Windows XP Professional Edition  (SP 3) - Version: 5.1.2600 (x86))
Format                          : application/pdf
Document ID                     : uuid:3e7549cf-506f-4d76-9e7e-bbb8de94acad
Instance ID                     : uuid:540113dd-df68-4cb2-aca8-acec8916127f
Page Count                      : 3
Page Layout                     : OneColumn

EXIF Metadata provided by EXIF.tools