Chungear Co CE10507 CEILING FAN REMOTE CONTROLLER (TRANSMITTER) User Manual

Chungear Industrial Co Ltd CEILING FAN REMOTE CONTROLLER (TRANSMITTER)

User Manual

DC POWER CEILING FAN REMOTE CONTROL MANUALLEARNING PROCESSNOTE:The Hand Held Remote Control System is equipped with a learning frequency function which hascode combinations to prevent potential interference from other remote units.Step:1.Installthe1.5V/AAA2pcsbatteries.Within30secondsofturningtheReceiversACpowerON.Pressthetransmitter’s“LEARN”button.Step:2.Holdthe“LEARN”buttonforover5seconds,oncethereceiverhasdetectedthefrequency,thereceiverwillmakesound,BiBi,twice. This will indicate the receiver has learned thefrequencythatwaspreviouslyselectedonthetransmitter.NOTE:AftertheACpowerison,donotpressanyotherbuttononthetransmitterbeforepressingthe“LEARN”button,Becausedoingsowillcausetheproceduretofail.Aftercompletingthestepsabove,youshouldbeabletooperatetheceilingfanandlight.Ifthefanisnotrespondingtothetransmitter,please turn the power off to the receiver. And repeat step 1 and 2.NOTE:Removethebatteryifnotusedforlongperiodsoftimetopreventdamage to the hand held remote.LIGHT FUNCTION SELECT SWITCHIf installed energy light onto ceiling fan, please slide the “light function select switch” to “O” position. If installed tungstenlight onto ceiling fan, please slide the “light function select switch” to “D” position.FUNCTIONS OF TRANSMITTER1. FAN SPEED：1: Turn on ceiling fan at 1st speed (lowest speed)2. Turn on ceiling fan at 2nd speed3. Turn on ceiling fan at 3rd speed4. Turn on ceiling fan at 4th speed5. Turn on ceiling fan at 5th speed6. Turn on ceiling fan at 6th speed (high speed): Turn off ceiling fan.2. FAN TIMER: When the fan turned on.2H ：Setting up that the ceiling fan will turn off after 2 hours automatically.4H ：Setting up that the ceiling fan will turn off after 4 hours automatically.8H ：Setting up that the ceiling fan will turn off after 8 hours automatically.Press button can cancel fan timer setting.3. --“F/R” :Hold this button 2 seconds to set fan wind direction up or down.4. -- Natural breeze: Fan speed will modulate to simulate a natural breeze.Press and turn the light on or off. DIMMER-Press and hold to dim or brightenlightto the desired level and release.(Tungsten only and light function select switch on “D” position.)5. Installation of Transmitter Wall Mount Holder with Two screws.TR249A
To assure continued FCC compliance:FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect theequipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or anexperienced radio/TV technician for help.CAUTION:To assure continued FCC compliance:Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operatethe equipment.FCC ID：KUJCE10507This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) this device must accept any interference received, including interference that maycause undesired operation.

Navigation menu