Chungear Co CE10610 Ceiling Fan Remote Controller (Transmitter) User Manual

Chungear Industrial Co Ltd Ceiling Fan Remote Controller (Transmitter)

User Manual

CEILING FAN REMOTE CONTROLLEROPERATION AND INSTALLATION INSTRUCTIONS(Please keep this instruction pamphlet.)IMPORTANT POINTS TO REMEMBER:1. Read and save these instructions.2. Please note that all fixed wiring appliances should be installed by a qualified electrician.3. The supply to the remote control receiver should be connected through a mains switch, i.e.existing wall switch.4. Disconnect from power supply at wall switch before working on remote control receiver orceiling fan.5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection.6. This unit is to be used for the control of ceiling fan and in an AC110/120V 60Hz power supplyonly.7. Do not install in damp locations or immerse in water. (For indoor use only.)8. Do not pull on or cut leads shorter.9. Do not drop or bump the unit.10.PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takesplace as this will damage the transmitter. Dispose of used battery properly, keep the battery outof reach of children.11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with anyvariable (rheostat) wall control.INSTALLATION INSTRUCTIONS1. Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the“Light Switch” after installation.2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket.The canopy comes up to cover the receiver and bracket.IMPORTANTYOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT KIT(IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL.CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
LEARNING PROCESS1. This unit finished learning process inside manufactory, if replacetransmitter or receiver, user need to redo learning process before usingthis unit.2. Install the battery 12V in transmitter.3. After installing the unit and power on and press key 1~3seconds,lights will be flashing twice and turn off, which indicate that learning process finished. Learningeffect distance is same with remote’s. Please note that must press the “” within 30sensondsafter power on.4. Please note that the transmitter can learn in multiple receiver, when doing learning processplease make sure not learn in other receiver. Suggest to separate power switches of fans in 2meter range.FUNCTIONS OF TRANSMITTER: ON/OFF- Press and release immediately to turn on or off the light.DIMMER-Press and hold over 5 seconds to dim or brighten lightto the desired level and release. (Tungsten only.): Turn off the ceiling fan.:Turn on the fan at high speed:Turn on the fan at medium speed: Turn on the fan at low speedFEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouragedto try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connectthe equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer oran experienced radio/TV technician for help.CAUTION:Any changes or modifications not expressly approved by the grantee of this device could void the user's authority tooperate the equipment.FCC ID：KUJCE10610This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.To assure continued FCC compliance:Installation ofTransmitter Wall MountHolder with twoscrews.TR214A

Navigation menu