Chungear Co CE10610 Ceiling Fan Remote Controller (Transmitter) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3594175
Application ID	g9IKqovV5EqrIMbPtd/Ijg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	46.59kB (582401 bits)
Date Submitted	2017-10-06 00:00:00
Date Available	2017-10-06 00:00:00
Creation Date	2017-09-29 17:56:29
Producing Software	Microsoft: Print To PDF
Document Lastmod	2017-10-02 13:20:25
Document Title	C:\Users\RD1-Assistant\Desktop\æ‹‚çı—æŒ⁄件\TR214A FCC赗挎\TR214A+JY326B 141203.doc
Document Author:	RD1-Assistant

CEILING FAN REMOTE CONTROLLER
OPERATION AND INSTALLATION INSTRUCTIONS
(Please keep this instruction pamphlet.)
IMPORTANT
YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT KIT
(IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL.
IMPORTANT POINTS TO REMEMBER:
1. Read and save these instructions.
2. Please note that all fixed wiring appliances should be installed by a qualified electrician.
3. The supply to the remote control receiver should be connected through a mains switch, i.e.
existing wall switch.
4. Disconnect from power supply at wall switch before working on remote control receiver or
ceiling fan.
5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection.
6. This unit is to be used for the control of ceiling fan and in an AC110/120V 60Hz power supply
only.
7. Do not install in damp locations or immerse in water. (For indoor use only.)
8. Do not pull on or cut leads shorter.
9. Do not drop or bump the unit.
10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes
place as this will damage the transmitter. Dispose of used battery properly, keep the battery out
of reach of children.
11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any
variable (rheostat) wall control.
INSTALLATION INSTRUCTIONS
CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
1. Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the
“Light Switch” after installation.
2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket.
The canopy comes up to cover the receiver and bracket.
LEARNING PROCESS
1. This unit finished learning process inside manufactory, if replace
transmitter or receiver, user need to redo learning process before using
this unit.
2. Install the battery 12V in transmitter.
3.
After installing the unit and power on and press
key 1~3seconds,
lights will be flashing twice and turn off, which indicate that learning process finished. Learning
effect distance is same with remote’s. Please note that must press the “” within 30sensonds
after power on.
4. Please note that the transmitter can learn in multiple receiver, when doing learning process
please make sure not learn in other receiver. Suggest to separate power switches of fans in 2
meter range.
FUNCTIONS OF TRANSMITTER
: ON/OFF- Press and release immediately to turn on or off the light.
DIMMER-Press and hold over 5 seconds to dim or brighten light
to the desired level and release. (Tungsten only.)
: Turn off the ceiling fan.
:Turn on the fan at high speed
:Turn on the fan at medium speed
TR214A
Installation of
Transmitter Wall Mount
: Turn on the fan at low speed
Holder with two
screws.
To assure continued FCC compliance:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect
the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or
an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to
operate the equipment.
FCC ID：KUJCE10610
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
XMP Toolkit                     : 3.1-702
Create Date                     : 2017:09:29 17:56:29+08:00
Modify Date                     : 2017:10:02 13:20:25+08:00
Metadata Date                   : 2017:10:02 13:20:25+08:00
Format                          : application/pdf
Creator                         : RD1-Assistant
Title                           : C:\Users\RD1-Assistant\Desktop\æ‹‚çı—æŒ⁄件\TR214A FCC赗挎\TR214A+JY326B  141203.doc
Producer                        : Microsoft: Print To PDF
Document ID                     : uuid:585f02d3-9d08-4db8-b3b2-0bd7d2aeb5cd
Instance ID                     : uuid:4d481676-a78c-47bb-95ae-800e54467994
Warning                         : Pages object (2 0 obj) not found at 574661
Author                          : RD1-Assistant

EXIF Metadata provided by EXIF.tools