Chungear Co CE10612 Ceiling Fan Remote Controller (Transmitter) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3654613
Application ID	UNdH5iq48fXZQJ54M56ZIw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.31kB (428914 bits)
Date Submitted	2017-11-28 00:00:00
Date Available	2017-11-28 00:00:00
Creation Date	2017-11-22 11:42:43
Producing Software	Microsoft: Print To PDF
Document Lastmod	2017-11-23 17:28:02
Document Title	C:\Users\RD1-Assistant\Desktop\æ‹‚çı—æŒ⁄件\TR292A FCC赗挎\è¡łæŸŁæ‘’ä¾ł\TR292AèªªæŸ”æł¸.doc
Document Author:	RD1-Assistant

DC POWER CEILING FAN REMOTE CONTROL MANUAL
LEARNING PROCESS
NOTE：The Hand Held Remote Control System is equipped with a learning frequency function
which has code combinations to prevent potential interference from other remote units
Step: 1 Open the remote battery cover and install DC3V,CR2032 2pcs batteries
Step: 2 Within 30 seconds of turning the Receivers AC power ON.
Step: 3 Press and hold remote “LEARN” key for over 5 seconds, once the receiver has
detected the frequency, the receiver will make sound, Bi Bi, twice. This will
indicate the receiver has learned the frequency that was previously selected on
the transmitter.
NOTE: After the AC power is on, do not press any other button on the transmitter
before setting learning. Doing so will cause the procedure to fail. After completing the
steps above, you should be able to operate the ceiling fan and light. If the fan is not
responding to the transmitter, please turn the power off to the receiver. And repeat step
1 and 2.
NOTE: Remove the battery if not used for long periods of time to prevent damage to the hand held remote.
FUNCTIONS OF TRANSMITTER
1.
：To turn the fan on or off.
LED indicator speed position
2. + : Press this button to increasing fan speed and LED indicator would be on the position
of fan speed. (1~6 speed)
3.
- :
Press this button to decreasing fan speed and LED indicator would be on the
position of fan speed.(1~6 speed)
4. FAN TIMER:
2hr：Setting up that the ceiling fan will turn off after 2 hours automatically.
4hr：Setting up that the ceiling fan will turn off after 4 hours automatically.
8hr：Setting up that the ceiling fan will turn off after 8 hours automatically.
Press fan speed button to deactivate
5.
6.
: To set fan wind direction up or down.
: Tap once to activate. Light on ceiling fan blinks once to confirm Walk
Away Delay is active. The light turns off after 1 minute. Press any key to cancel function.
7.
TR292A
: Home Shield--Press and hold button to activate. Light on ceiling fan blinks two times to confirm
Home Shield is active. Fan remains off and the light randomly turns on for a minimum of 5 minutes and a
maximum of 20 minutes. The light remains off for 60 minutes between events. To deactivate press any
button once
8.
: “NATURAL FLOW”, press the button for set fan speed change automatically. If fan speed is on 1st, 2nd,
or 3rd, press this button for low fan speed changing automatically. If fan speed is on 4th, 5th, or 6th, press
this button for high fan speed changing automatically. Press Fan Speed to deactivate.
9.
：To turn on and turn off the light.
10. When pressing remote button, the LED indicator on position 1 would be on. If you press remote button and
LED indicator would not be on, you should change new DC3V,CR2032 2pcs batteries.
To assure continued FCC compliance:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult
the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to
operate the equipment.
FCC ID：KUJCE10612
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-702
Create Date                     : 2017:11:22 11:42:43+08:00
Modify Date                     : 2017:11:23 17:28:02+08:00
Metadata Date                   : 2017:11:23 17:28:02+08:00
Format                          : application/pdf
Creator                         : RD1-Assistant
Title                           : C:\Users\RD1-Assistant\Desktop\æ‹‚çı—æŒ⁄件\TR292A FCC赗挎\è¡łæŸ�æ‘’ä¾ł\TR292AèªªæŸ”æł¸.doc
Producer                        : Microsoft: Print To PDF
Document ID                     : uuid:2d73ae58-66df-45e3-ac63-e30402c8973b
Instance ID                     : uuid:048f4350-10f6-4281-a3ea-e54908af34b6
Page Count                      : 2
Author                          : RD1-Assistant

EXIF Metadata provided by EXIF.tools