Chungear Co CE9908 Ceiling Fan Remote Controller (Transmitter) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1395349
Application ID	esFEVxz5rRssAgDfnUGyUA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.93kB (86571 bits)
Date Submitted	2010-12-22 00:00:00
Date Available	2010-12-22 00:00:00
Creation Date	2010-12-15 09:46:11
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2010-12-15 09:49:48
Document Title	untitled

CEILING FAN REMOTE CONTROLLER
OPERATION AND INSTALLATION INSTRUCTIONS
(Please keep this instruction pamphlet.)
IMPORTANT
YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT KIT (IF ANY)
TO ON POSITION BEFORE OPERATING REMOTE CONTROL.
IMPORTANT POINTS TO REMEMBER:
1.
Please read and save these instructions.
2.
Please note that all fixed wiring appliances should be installed by a qualified electrician.
3.
The supply to the remote control receiver should be connected through a mains switch, i.e. existing
wall switch.
4.
Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.
5.
Install receiver into the ceiling fan canopy of the fan to ensure proper protection.
6.
This unit is to be used for the control of ceiling fan and in an AC120V 60Hz power supply only, rated
max 1.25A for fan, max 300W for light.
7.
Do not install in damp locations or immerse in water. (For indoor use only.)
8.
Do not pull on or cut leads shorter.
9.
Do not drop or bump the unit.
10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place
as this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach of
children.
11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable
(rheostat) wall control.
INSTALLATION INSTRUCTIONS
CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
1.
Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the “Light
Switch” after installation.
2.
Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The
canopy comes up to cover the receiver and bracket.
CODE SWITCH
1.
CODE SWITCH: Codes are set by pushing dip switches up or down. It is imperative that the code
used for both transmitter and receiver is exactly the same, otherwise remote controller will not work.
Please note the code switch will enable you to operate a second remote controller independently. For
example, if you have two ceiling fans with 2 remote control units, set 2 different codes for each set of
transmitter/receivers. This means you can operate each ceiling fan independently.
2.
Your remote control is ready for use after battery installation(need 12V battery 1pc).
TO OPEN BATTERY HOUSING
COVER BY PRESS DOWN AND
SLIDE OUT
ON DIP
DIP SWITCH
RECEIVER
ANTENNA
FUNCTIONS OF TRANSMITTER
TRANSMITTER
OFF : Turn off the ceiling fan.
HI
:Turn on the fan at high speed
MED
:Turn on the fan at medium speed
LOW
: Turn on the fan at low speed
L.LOW : Turn on the fan at lowest speed
LIGHT ON/OFF: Press and release immediately to turn on or off the light.
DIMMER
:Press and hold to dim or brighten lights to the desired level and
release. (Only for the tungsten bulb.)
Ceiling Fan Remote Control
Wiring Connection
To install the Transmitter
Wall Mount Holder with two
screws.
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to
operate the equipment.
FCC ID：KUJCE9908
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 3
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:7c68a342-4b45-4e53-9a64-67eca17b3e91
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2010:12:15 09:46:11+08:00
Modify Date                     : 2010:12:15 09:49:48+08:00
Metadata Date                   : 2010:12:15 09:49:48+08:00
Document ID                     : uuid:50b51a8b-2251-4d36-aa50-fcab8357af24
Format                          : application/pdf
Title                           : untitled

EXIF Metadata provided by EXIF.tools