CipherLab 1661 BT Barcode Scanner User Manual 1660 Barcode Scanner
CipherLab Co., Ltd. BT Barcode Scanner 1660 Barcode Scanner
UserManual.wiki
>
CipherLab
>
1661 User Manual
manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![2 Enter Setup 1660 Barcode Scanner User Guide GETTING FAMILIARIZED WITH 1660/1661 AND 3610 INSTALLING BATTERIES TO 1660/1661 1) Hold the scanner face down in one hand. 2) Press the battery lid release and slide the battery lid. 3) Remove the battery lid by the other hand. 4) Hold the scanner still and insert the battery or batteries into the battery compartment. For 1660, install two AAA Alkaline batteries into the battery compartment, each in the right direction. 5) Replace the battery lid and lock it firmly. 6) Hold down the [Power/Delete] key for about 2 seconds to turn on the scanner. The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. Note: (1) To turn off the scanner, press the [Power/Delete] key for 2 seconds. The scanner will respond with two short beeps (high tone) and the LED will finally become solid red. Release the key then. Otherwise, let the scanner turn off automatically in specific circumstances. Refer to settings of “Auto Power Off”. (2) For shipping and storage purposes, save the scanner and the batteries separately. This will keep the batteries in good condition for future use.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-10.png)
![3 Update 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 CHARGING THE BATTERY FOR 1661 The battery may not be charged to full for shipment. When you first receive the package, you will need to charge the battery to full before using the scanner. For 1661, use the Direct USB cable to connect the scanner to PC for charging. Note: Battery charging stops when the temperature drops below 0°C or exceeds 40°C. It is recommended to charge the battery at room temperature (18°C to 25°C) for optimal performance. It takes approximately 4 hours to charge the battery to full. 1) Install the battery to 1661. 2) Connect 1661 to your computer or notebook via the USB cable. 3) The scanner LED will be flashing red during charging. When the charging is done, the LED will turn off. When charging error occurs, the LED will turn solid red.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-11.png)
![5 Update 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 USING 3610 The BT Transponder (3610) is specifically designed for the scanner to communicate with a host computer wirelessly. The connection between the scanners and 3610 is made easy and reliable. Refer to 3.1.1 Connect to 3610. There is one LED indicator provided for communications status. Communication LED Meaning --- Blue, solid Initialize Red, solid --- Failed to establish a USB connection Red, solid Blue, flashing Serial command mode with USB Virtual COM: wait 3 seconds for starting a serial command Red, flashing Blue, flashing Serial command mode with USB HID: wait 3 seconds for pressing [Num Lock] or [Caps Lock] 5 times via keyboard --- Blue, flashing Wait for connection request from the scanner (Slow flash at 0.5 Hz) --- Blue, flashing Connected with the scanner (Fast flash at 1 Hz) Red, solid Blue, flashing Failed to send data to host via USB Virtual COM (Fast flash at 1 Hz) Red, flashing --- Enter Download Mode](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-13.png)
![7 Update 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 SYMBOLOGIES SUPPORTED Most of the popular barcode symbologies are supported, as listed below. Each can be individually enabled or disabled. The scanner will automatically discriminate and recognize all the symbologies that are enabled. Refer to Chapter 4 Changing Symbology Settings for details of each symbology. Symbologies Supported: Enable/Disable Default Codabar Enabled Code 93 Enabled MSI Disabled Plessey Disabled Telepen Disabled Code 128 Code 128 Enabled GS1-128 (EAN-128) Disabled ISBT 128 Enabled Code 2 of 5 Industrial 25 Enabled Interleaved 25 Enabled Matrix 25 Disabled Code 3 of 9 Code 39 Enabled Italian Pharmacode Disabled French Pharmacode Disabled EAN/UPC EAN-8 Enabled EAN-8 Addon 2 Disabled EAN-8 Addon 5 Disabled EAN-13 Enabled EAN-13 & UPC-A Addon 2 Disabled EAN-13 & UPC-A Addon 5 Disabled ISBN Disabled UPC-E0 Enabled UPC-E1 Disabled UPC-E Addon 2 Disabled UPC-E Addon 5 Disabled UPC-A Enabled](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-15.png)
![9 Update The configuration of the scanner can be done by reading the setup barcodes contained in this manual or via the ScanMaster software. This section describes the procedure of configuring the scanner by reading the setup barcodes and provides some examples for demonstration. Configuration Mode 1. Hold down the [Power/Delete] key for about 2 seconds to turn on the scanner. It will respond with a long beep and its LED will come on-off shortly. 2. Have the scanner read the “Enter Setup” barcode. It will respond with six beeps and its LED indicator will become flashing red after reading the barcode. 3. Have the scanner read more setup barcodes… Most of the setup barcodes are normal, and the scanner will respond with two beeps (low-high tone). For special setup barcodes, it requires reading more than one setup barcode to complete the setting. 4. Have the scanner read the “Update” or “Abort” barcode. It will respond with six beeps and its LED indicator will become flashing red after reading the barcode. 5. The scanner will restart automatically upon reading the “Update” or “Abort” barcode. It will respond with a long beep and its LED will come on-off shortly. Note: Refer to Appendix II Host Serial Commands for how to configure the 3610 dongle by having the scanner read 3610-related setup barcodes or using serial commands. QUICK START](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-17.png)
![11 Update 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 ENTER CONFIGURATION MODE For the scanner to enter the configuration mode, you must have it read the "Enter Setup" barcode, which can be located at the bottom of almost every even page of this manual. The scanner will respond with six beeps and its LED indicator will become flashing red after reading the barcode. Enter Setup For configuring scanner parameters, see “Read a Setup Barcode” below. EXIT CONFIGURATION MODE For the scanner to save settings and exit the configuration mode, you must have it read the “Update” barcode, which can be located at the bottom of almost every odd page of this manual. If you want to exit the configuration mode without saving any changes, have the scanner read the “Abort” barcode instead. Just like reading the “Enter Setup” barcode, the scanner will respond with six beeps and its LED indicator will become flashing red after reading the barcode. Wait for a few seconds for the scanner to restart itself. Update Abort](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-19.png)
![13 Update 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 READ A SETUP BARCODE CONFIGURE PARAMETERS For most of the scanner parameters, only one read is required to set them to new values. The scanner will respond with two beeps (low-high tone) when each parameter is set successfully. Refer to Create One-Scan Setup Barcodes. But for a number of special parameters, multiple reads are required to complete the setting. In this case, the scanner will respond with a short beep to indicate it needs to read more setup barcodes. These special parameters may require reading one or more setup barcodes, such as Numeric barcodes, say, for keyboard type, inter-character delay, length qualification Hexadecimal barcodes, say, for character strings as prefix, suffix, etc. When “BT HID” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. You may decide whether or not to change key status when “Normal Key” is selected for Key Type. To complete the configuration of these special parameters, it requires reading the “Validate” barcode, and the scanner will respond with two beeps (low-high tone) to indicate the input values are validated.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-21.png)
![15 Update 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 The example below shows how to set numeric parameters: Steps Action User Feedback if Successful 1 Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. 2 Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red. 3 Read a Setup barcode... For example, The scanner will respond with two beeps (low-high tone) if reading a normal setup barcode. The scanner will respond with one short beep if reading a special setup barcode such as “Max. Length”, indicating the setup requires reading more barcodes. Read the “Decimal Value” barcode(s). Refer to Appendix IV “Decimal System” The scanner will respond with two beeps (low-high tone) when the input values are validated. 4 Exit the Configuration Mode… OR Same as for Enter the Configuration Mode. 5 The scanner will automatically restart itself… Same as for Power on the scanner. Normal setup barcode Special setup barcode Decimal barcodes Normal setup barcode](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-23.png)
![17 Update 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 LIST THE CURRENT SETTINGS The current settings of all scanner parameters can be sent to the host computer for user inspection. The listing includes pages as shown below. You can select the page of interest by having the scanner read the “List Page x” barcode. The scanner will respond with two beeps (low-high tone) and send the selected page to the host immediately. List settings regarding Firmware Version, Serial Number, Interface, Buzzer, and Other Scanner Parameters List Page 1 List settings regarding Prefix, Suffix, and Length Code Setting List Page 2 List settings regarding Code ID List Page 3 List settings regarding: Readable Symbologies List Page 4 List settings regarding Symbology Parameters (1/3) List Page 5 List settings regarding Symbology Parameters (2/3) List Page 6 List settings regarding Symbology Parameters (3/3) List Page 7 List settings regarding Editing Format 1 List Page 8 List settings regarding Editing Format 2 List Page 9 List settings regarding Editing Format 3 List Page 10](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-25.png)
![19 Update 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 CREATE ONE-SCAN SETUP BARCODES The fact is most of the scanner parameters require only one read for setting new values. To facilitate configuring the scanner, you may create One-Scan setup barcodes for use. The requirements of a One-Scan setup barcode are: a prefix of the “#@” characters the six digits of command parameters a suffix of the “#”character For example, the scanner needs reading three setup barcodes for the command parameter “109952” to take effect: Enter Setup List Page 3 Update Now, it requires only one read: One-Scan Setup Barcode for 109952 Note: The scanner will restart automatically upon reading the One-Scan setup barcode for (1) changing the interface or (2) setting memory mode, enable or disable. It will respond with a long beep and its LED will come on-off shortly.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-27.png)
![21 Update This chapter explains the features and usage of the barcode scanner. IN THIS CHAPTER 1.1 Battery ...................................................................... 21 1.2 Memory ..................................................................... 26 1.3 LED Indicator ............................................................. 29 1.4 Beeper....................................................................... 31 1.5 Send "NR" to Host ....................................................... 35 1.6 Scan Modes ................................................................ 36 1.7 Scanner Time-out ....................................................... 41 1.8 Delay between Re-read ................................................ 42 1.9 Read Redundancy for All Symblogies ............................. 43 1.10 Addon Security for UPC/EAN Barcodes ......................... 44 1.11 Negative Barcodes..................................................... 45 1.12 Effective Decoding Area ............................................. 46 1.1 BATTERY The scanner is battery-powered: 1660 uses two AAA Alkaline batteries, while 1661 uses a rechargeable 3.7 V/850 mAh Li-ion battery. For intensive data collection, you may prepare spare battery or batteries for non-stop operation. Note: (1) The rechargeable battery for 1661 may not be charged to full for shipment. We suggest charging it to full before use. (2) The scanner can be configured to save battery power. Refer to settings of “Auto Power Off & Power-Saving”, “Sniff Mode”, as well as “Low Battery Alarm”. 1.1.1 HOW TO OPERATE THE SCANNER Turn on the scanner… Press the [Power/Delete] key for about 2 seconds. The scanner will respond with a long beep (high tone), and its LED indicator will become solid red and go off quickly. Turn off the scanner… Press the [Power/Delete] key for about 2 seconds. The scanner will respond with two short beeps (high tone) and the LED will finally become solid red. Release the key then. Otherwise, let the scanner turn off automatically in specific circumstances. Chapter 1 UNDERSTANDING THE BARCODE SCANNER](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-29.png)
![22 Enter Setup 1660 Barcode Scanner User Guide Delete the last collected data when in memory mode … Press the [Power/Delete] key. The scanner will respond with two short beeps (high tone) and the LED will become solid red. Before the LED goes off (within 1 second), press the [Power/Delete] key again to confirm the deletion. Note: For the scanner to restore system defaults during operation, use key combination in the following sequence: Hold down the [Power/Delete] key until its LED indicator becomes solid red, and without releasing the key, you must press the [Trigger] key simultaneously for 3 seconds. Then, the scanner will respond with a long beep (high tone), and the indicator will go off.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-30.png)
![23 Update Chapter 1 1.1.2 AUTO POWER OFF & POWER-SAVING The scanner will stay active at power-on, which may be followed by a transition from full CPU speed to low CPU speed (Power-Saving) to auto shutdown (Auto Power Off). Power-Saving (1~254 min.; 0= Disable): By default, it is set to stand by at full-speed for 2 minutes before it enters low-speed mode. If this feature is not desired, set it to 0. Auto Power Off (1~254 min.; 0= Disable): By default, it is set to automatically shut down after 10 minutes. If this feature is not desired, set it to 0. Note: The Power-Saving setting will not take effect when a WPAN connection has been established successfully, via BT HID or SPP. Before establishing a WPAN connection successfully… 1. The scanner will stay active for a specified period of time (2 minutes by default) for the following scenarios. Its CPU is running at full speed, and the LED is flashing blue (On/Off ratio 0.5 s: 0.5 s). (a) waiting for a connection request from the host (BT SPP Slave Mode) (b) trying to connect to the host (BT HID or BT SPP Master Mode) (c) trying to connect to 3610 2. If it fails to connect within 2 minutes, the scanner will become inactive to save power for the remaining period of time (the specified value minus 2 minutes). Its CPU is running at low speed, and the LED is flashing red (On/Off ratio 0.3 s: 2.5 s). Press the [Trigger] key to wake up the scanner when it becomes inactive, and the scanner will stay active again. 3. If it fails to connect again and again, and finally stays inactive until the specified time interval for Auto Power Off has elapsed, the scanner will automatically turn off in order to conserve battery power. Hold down the [Power/Delete] key for about 2 seconds to turn it on. Note: For scenarios (a) and (b) in step 1, on your computer you may need to search for the scanner again.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-31.png)
![24 Enter Setup 1660 Barcode Scanner User Guide After establishing a WPAN connection successfully… 1. Once a WPAN connection is established successfully, the scanner will stay active for a specified period of time (2 minutes by default) for data transmission. Its CPU is running at full speed, and the LED is flashing blue (On/Off ratio 0.02 s: 3 s). 2. If it is idle within 2 minutes, the scanner will become inactive to save power for the remaining period of time (the specified value minus 2 minutes). Its CPU is running at low speed, and the LED is flashing red (On/Off ratio 0.3 s: 2.5 s). Press the [Trigger] key to wake up the scanner when it becomes inactive, and the scanner will stay active again. For BT HID or SPP, there is no transition from full CPU speed to low CPU speed. However, when connecting with 3610, the scanner will go through the transition in order to save power. 3. If it is idle and finally stays inactive until the specified time interval for Auto Power Off has elapsed, the scanner will automatically turn off in order to conserve battery power. You will hear three short beeps, tone descending from high to low. Hold down the [Power/Delete] key for about 2 seconds to turn it on. For BT HID, the scanner will resume connection with the host upon powering on again, as long as the host application is running. You will hear three short beeps, tone ascending from low to high. If the scanner fails to resume connection, it will try every 5 seconds to re-connect to the host unless you have the scanner read the “Reset Connection” barcode. For BT SPP Slave Mode, the scanner must wait for the host to re-connect. For BT SPP Master Mode, the scanner will resume connection with the host upon powering on again, as long as the host application is running. You will hear three short beeps, tone ascending from low to high. If the scanner fails to resume connection, it will try every 5 seconds to re-connect to the host unless you have the scanner read the “Reset Connection” or “Restore System Defaults” barcode. With the use of 3610, the scanner will try re-connecting to 3610 unless you turn off the scanner.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-32.png)
![29 Update Chapter 1 1.3 LED INDICATOR The triple-color LED on top of the scanner is used to provide user feedback. For example, the LED becomes solid red and goes off quickly upon powering on or running out of transmit buffer. You may tell the difference by the beeps – you will hear a long beep of high tone when powering on the scanner, and a long beep of low tone when the transmit buffer becomes full. Scanner LED Meaning Red, on-off --- --- Power on, with one long beep (high tone, LED on for 1 second) Data saved to buffer when transmit buffer is enabled and the scanner is out of range, with two short beeps (high-low tone) Transmit buffer full, with one long beep (low tone) Transmit buffer disabled, with one long beep (low tone) Delete the last collected data in memory mode, with two short beeps (high tone, LED on for 1 second) Memory full in memory mode, with two short beeps (high-low tone) Red, flashing --- --- Flashing red (On/Off ratio 0.3 s: 2.5 s) indicates the scanner is inactive and its CPU running at low speed to save power (because no WPAN connection is established after waiting for two minutes) Configuration Mode (On/Off ratio 0.5 s: 0.5 s) --- --- Green, on-off Good Read, with one short beep (high tone) and beeper pitch and duration programmable --- Blue, flashing --- First, flashing blue (On/Off ratio 0.5 s: 0.5 s) for two minutes indicates the scanner is waiting for connection, and goes off if no connection is established, then flashing red (On/Off ratio 0.3 s: 2.5 s) indicates the scanner is inactive. It is ready for connection only while the LED is flashing blue — SPP Slave: waiting host to connect HID or SPP Master: trying to connect to host Using 3610: trying to connect to 3610 --- Blue, flashing --- Flashing blue (On/Off ratio 0.1 s: 0.1 s) indicates the scanner receives a PIN code request from host (flashing more quickly than waiting connection). --- Blue, flashing --- Flashing blue (On/Off ratio 0.02 s: 3 s) indicates the scanner has established a WPAN connection successfully. --- Blue, flashing Green, flashing Flashing blue and green (On/Off ratio 0.1 s: 0.1 s) indicates an error occurs while entering the PIN code. Press the [Trigger] key to get ready for re-connecting.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-37.png)
![49 Update In order to establish a proper connection between your computer and the scanner, we suggest that you follow these instructions – 1) Install batteries and hold down the [Power/Delete] key for about 2 seconds to turn on the scanner. 2) Have the scanner read the “Enter Setup” barcode to enter the configuration mode. 3) Have the scanner read the associated barcodes to activate the desired interface. See the following sections for output interfaces supported. 4) Have the scanner read the barcodes for related settings. 5) Have the scanner read the “Update” barcode to exit the configuration mode. 6) Turn on your computer or laptop and establish a WPAN connection with the scanner. Refer to Chapter 3 – Setting up a WPAN Connection. Note: By default, the output interface is set to “BT HID”. IN THIS CHAPTER 2.1 BT HID ...................................................................... 50 2.2 BT SPP Slave .............................................................. 61 2.3 BT SPP Master ............................................................ 63 2.4 USB HID via 3610 ....................................................... 67 2.5 USB Virtual COM via 3610 ............................................ 76 Chapter 2 SELECTING OUTPUT INTERFACE](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-57.png)
![51 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 BT HID By default, the keyboard type is set to PCAT (US). The following keyboard types are supported — No. Keyboard Type No. Keyboard Type 64 PCAT (US) 71 PCAT (Belgium) 65 PCAT (French) 72 PCAT (Spanish) 66 PCAT (German) 73 PCAT (Portuguese) 67 PCAT (Italy) 74 PS55 A01-2 (Japanese) 68 PCAT (Swedish) 75 User-defined table 69 PCAT (Norwegian) 76 PCAT (Turkish) 70 PCAT (UK) 2.1.2 RESET CONNECTION For BT HID, you can only have the scanner connected to one computer at a time. If you want to connect the scanner to another host, you must have it read the “Reset Connection” barcode so that the current connection record will be cleared. Then, the scanner will restart itself automatically. Go through the whole process in 3.2.3 Connect to Dongle to establish a new connection. Reset Connection Note: The “Restore System Defaults” barcode will have the current connection record cleared as well.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-59.png)
![53 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 US Keyboard Style – Normal QWERTY layout, which is normally used in western countries. Select “Lower Row” for the “Digits Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style. Select “Upper Row” for the “Digits Layout” setting for the lower row is for special characters. German Keyboard Layout – QWERTZ German layout; see below for German Keyboard Style. Select “Lower Row” for the “Digits Layout” setting for the upper row is for special characters.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-61.png)
![54 Enter Setup 1660 Barcode Scanner User Guide Digits Layout Select a proper layout that matches the alphabets layout. The scanner will make adjustments according to this setting. Options Description Normal Depends on the [Shift] key or [Shift Lock] setting Lower Row For QWERTY or QWERTZ keyboard Upper Row For AZERTY keyboard *Normal Upper Row Lower Row Note: This setting is to be used with the Character Substitution setting when support to certain keyboard types (languages) is unavailable but required.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-62.png)
![55 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Capital Lock Type & Setting In order to send the alphabets with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabets being transmitted. Cap Lock Type Description Normal Normal type Capital Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters. However, this does not affect the number or punctuation keys. Shift Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters. In addition, this affects the number or punctuation keys. *Normal Shift Lock Capital Lock Capital Lock State Description Capital Lock OFF Assuming that the status of Caps Lock on the keyboard is OFF, transmitted characters are exactly the same as in the barcode (when "case-sensitive" is selected for Alphabets Transmission). Capital Lock ON Assuming that the status of Caps Lock on the keyboard is ON, transmitted characters are exactly the same as in the barcode (when "case-sensitive" is selected for Alphabets Transmission). Refer to the Capital Lock Type above. Auto Detection The scanner will automatically detect the status of Caps Lock on the keyboard before data is transmitted; transmitted characters are exactly the same as in the barcode (when "case-sensitive" is selected for Alphabets Transmission). This setting is not supported on PDAs. Auto Detect Capital Lock ON](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-63.png)
![57 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Alphabets Transmission By default, the alphabets transmission is case-sensitive, meaning that the alphabets will be transmitted according to their original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabets transmitted according to the status of Caps Lock on the keyboard only. Ignore Case *Case-sensitive Refer to 5.1 Letter Case.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-65.png)
![59 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.1.4 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the delay time is, the slower the transmission speed will be. Value Delay Time Value Delay Time 0 Disable 195 ~ 204 200 millisecond 1 ~ 14 10 millisecond 205 ~ 214 210 millisecond 15 ~ 24 20 millisecond 215 ~ 224 220 millisecond 25 ~ 34 30 millisecond 225 ~ 234 230 millisecond 35 ~ 44 40 millisecond 235 ~ 244 240 millisecond 45 ~ 54 50 millisecond 245 ~ 254 250 millisecond … … Inter-Function Delay… (*0~254) 1) Read the barcode to specify the inter-function delay. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。 for the desired inter-function delay (millisecond). 3) Read the “Validate” barcode on the same page to complete this setting. 2.1.5 HID CHARACTER TRANSMIT MODE By default, HID interface sends data to the host in batch. You may have the scanner read the “By Character” barcode to process data one character at a time. *Batch Processing By Character Note: “By Character” transmit mode is required when working with iPhone or iPad.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-67.png)
![60 Enter Setup 1660 Barcode Scanner User Guide 2.1.6 KEYPAD SUPPORT FOR IPHONE/IPAD When the scanner has been successfully connected to iPhone or iPad for data collection, the onscreen keypad of iPhone or iPad will disappear. You may have the scanner read the “Use POWER Key to Show or Hide Keypad” barcode in advance. Then, it will allow pressing the [Power/Delete] key to show or hide the onscreen keypad. Note: This function only works for (1) iPhone 4 and 3GS version 4.1 or later, and (2) iPad version 4.2 or later. *Normal Use POWER Key to Show or Hide Keypad Instead of using the [Power/Delete] key, you may have the scanner read the following barcode to show or hide the keypad. Show or Hide Keypad](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-68.png)
![61 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.2 BT SPP SLAVE For BT SPP Slave, refer to Chapter 3 – Setting up a WPAN Connection for related connection settings. 2.2.1 ACTIVATE BT SPP SLAVE MODE This is SPP Slave Mode. Activate BT SPP, Slave Mode 2.2.2 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the delay time is, the slower the transmission speed will be. Value Delay Time Value Delay Time 0 Disable 195 ~ 204 200 millisecond 1 ~ 14 10 millisecond 205 ~ 214 210 millisecond 15 ~ 24 20 millisecond 215 ~ 224 220 millisecond 25 ~ 34 30 millisecond 225 ~ 234 230 millisecond 35 ~ 44 40 millisecond 235 ~ 244 240 millisecond 45 ~ 54 50 millisecond 245 ~ 254 250 millisecond … … Inter-Function Delay… (*0~254) 1) Read the barcode above to specify the inter-function delay. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。 for the desired inter-function delay (millisecond). 3) Read the “Validate” barcode on the same page to complete this setting.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-69.png)
![63 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.3 BT SPP MASTER As a SPP master device, the scanner will be able to resume connection with the host upon powering on again, as long as the host application is running. If the scanner fails to resume connection, it will try every 5 seconds to re-connect to the host unless you have the scanner read the “Reset Connection” or “Restore System Defaults” barcode. For BT SPP Master, refer to 3.2.2 Configure Related Settings for related connection settings. Note: In SPP Master Mode, if it fails to re-connect within the specified period of time (2 minutes by default), the scanner will become inactive to save power. Once the re-connection is established successfully, the scanner will not go through transition from full CPU speed to low CPU speed even though it is idle during the specified time interval for Auto Power Off. It will automatically turn off when the time is up. Refer to 1.1.2 Auto Power Off & Power-Saving. 2.3.1 ACTIVATE BT SPP MASTER MODE This is SPP Master Mode. Activate BT SPP, Master Mode How to connect with the target device? Produce two setup barcodes for the target SPP slave device, just like what we do for 3610. “Set Connection” “MAC ID” Note: The “MAC ID” barcode must have a prefix of two characters, either “0x” or “0X”, followed by the real MAC address of the target device. Usage: 1. Read the “Activate BT SPP, Master Mode” barcode above and barcodes for connection settings, such as authentication and preset PIN. Skip this step if no connection settings are desired. 2. Read the “Set Connection” and “MAC ID” barcodes. The scanner will respond with one beep upon reading each of the barcodes. Set Connection Prefix “0X” to target MAC address](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-71.png)
![65 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.3.2 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the delay time is, the slower the transmission speed will be. Value Delay Time Value Delay Time 0 Disable 195 ~ 204 200 millisecond 1 ~ 14 10 millisecond 205 ~ 214 210 millisecond 15 ~ 24 20 millisecond 215 ~ 224 220 millisecond 25 ~ 34 30 millisecond 225 ~ 234 230 millisecond 35 ~ 44 40 millisecond 235 ~ 244 240 millisecond 45 ~ 54 50 millisecond 245 ~ 254 250 millisecond … … Inter-Function Delay… (*0~254) 1) Read the barcode above to specify the inter-function delay. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。 for the desired inter-function delay (millisecond). 3) Read the “Validate” barcode on the same page to complete this setting.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-73.png)
![67 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.4 USB HID VIA 3610 For USB HID, connect 3610 to the USB port of PC, and then connect the scanner to 3610. Run any text editor on your computer, and the scanned data will be transmitted to the computer. HID Settings Defaults Keyboard Type PCAT (US) Digits Layout Normal Capital Lock Type Normal Capital Lock State Off Alphabets Transmission Case-sensitive Digits Transmission Alphanumeric keypad Inter-Function Delay 0 (ms) 2.4.1 ACTIVATE USB HID & SELECT KEYBOARD TYPE When USB HID interface is activated, you will have to select a keyboard type to complete this setting. Activate 3610 USB HID & Select Keyboard Type… 1) Read the barcode above to activate USB HID and select a keyboard type. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。. Refer to the table below for the number of desired keyboard type. 3) Read the “Validate” barcode on the same page to complete this setting. USB HID By default, the keyboard type is set to PCAT (US). The following keyboard types are supported — No. Keyboard Type No. Keyboard Type 64 PCAT (US) 71 PCAT (Belgium) 65 PCAT (French) 72 PCAT (Spanish) 66 PCAT (German) 73 PCAT (Portuguese) 67 PCAT (Italy) 74 PS55 A01-2 (Japanese) 68 PCAT (Swedish) 75 User-defined table 69 PCAT (Norwegian) 76 PCAT (Turkish) 70 PCAT (UK)](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-75.png)
![69 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 US Keyboard Style – Normal QWERTY layout, which is normally used in western countries. Select “Lower Row” for the “Digits Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style. Select “Upper Row” for the “Digits Layout” setting for the lower row is for special characters. German Keyboard Layout – QWERTZ German layout; see below for German Keyboard Style. Select “Lower Row” for the “Digits Layout” setting for the upper row is for special characters.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-77.png)
![70 Enter Setup 1660 Barcode Scanner User Guide Digits Layout Select a proper layout that matches the alphabets layout. The scanner will make adjustments according to this setting. Options Description Normal Depends on the [Shift] key or [Shift Lock] setting Lower Row For QWERTY or QWERTZ keyboard Upper Row For AZERTY keyboard *Normal Upper Row Lower Row Note: This setting is to be used with the Character Substitution setting when support to certain keyboard types (languages) is unavailable but required.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-78.png)
![71 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Capital Lock Type & Setting In order to send the alphabets with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabets being transmitted. Cap Lock Type Description Normal Normal type Capital Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters. However, this does not affect the number or punctuation keys. Shift Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters. In addition, this affects the number or punctuation keys. *Normal Shift Lock Capital Lock Capital Lock State Description Capital Lock OFF Assuming that the status of Caps Lock on the keyboard is OFF, transmitted characters are exactly the same as in the barcode (when "case-sensitive" is selected for Alphabets Transmission). Capital Lock ON Assuming that the status of Caps Lock on the keyboard is ON, transmitted characters are exactly the same as in the barcode (when "case-sensitive" is selected for Alphabets Transmission). Refer to the Capital Lock Type above. Auto Detection The scanner will automatically detect the status of Caps Lock on the keyboard before data is transmitted; transmitted characters are exactly the same as in the barcode (when "case-sensitive" is selected for Alphabets Transmission). Auto Detect Capital Lock ON](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-79.png)
![73 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Alphabets Transmission By default, the alphabets transmission is case-sensitive, meaning that the alphabets will be transmitted according to their original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabets transmitted according to the status of Caps Lock on the keyboard only. Ignore Case *Case-sensitive Refer to 5.1 Letter Case.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-81.png)
![75 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.4.3 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the delay time is, the slower the transmission speed will be. Value Delay Time Value Delay Time 0 Disable 195 ~ 204 200 millisecond 1 ~ 14 10 millisecond 205 ~ 214 210 millisecond 15 ~ 24 20 millisecond 215 ~ 224 220 millisecond 25 ~ 34 30 millisecond 225 ~ 234 230 millisecond 35 ~ 44 40 millisecond 235 ~ 244 240 millisecond 45 ~ 54 50 millisecond 245 ~ 254 250 millisecond … … Inter-Function Delay… (*0~254) 1) Read the barcode above to specify the inter-function delay. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。 for the desired inter-function delay (millisecond). 3) Read the “Validate” barcode on the same page to complete this setting. 2.4.4 HID CHARACTER TRANSMIT MODE By default, HID interface sends data to the host in batch. You may have the scanner read the “By Character” barcode to process data one character at a time. *Batch Processing By Character](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-83.png)
![77 Update Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.5.3 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all three attempts fail without any notification, data loss will occur. ACK/NAK Time-out after … (*0~99) 1) Read the barcode above to specify the time interval for the scanner to send data and wait for a response from the host. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。. For example, read “1” and “0” for the scanner to automatically shut down after being idle for 1 second. 3) Read the “Validate” barcode on the same page to complete this setting. ACK/NAK Error Beep Enable Error Beep *Disable Error Beep Note: We suggest enabling the error beep so that you will be notified of such data loss and have the scanner re-read data.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-85.png)
![87 Update Chapter 3 3.2.3 CONNECT TO DONGLE The procedure goes through associating devices for establishing a WPAN connection, which is pretty much the same except for the software you are using. If your computer is running Microsoft® Windows® XP Service Pack 3 (SP3) or Windows Vista® Service Pack 1 (SP1), you can use the software support that Windows® includes, or you can use the driver that the device manufacturer provides. Now, let’s try using the software support that Windows® XP Service Pack 2 includes. BT HID Procedure By default, BT HID is activated on the scanner, and the keyboard type is set to PCAT (US). When BT HID is re-activated, you will have to select a keyboard type to complete this setting. The procedure is the same as for BT SPP. Refer to steps 1~11 below. BT SPP Slave Procedure 1. Turn on the Bluetooth® function on your computer, running Windows XP SP2. 2. Double-click the Bluetooth® icon from the lower right of the taskbar. Alternatively, you may go to Control Panel > Bluetooth Devices. 3. Click [Add] to search devices nearby.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-95.png)
![88 End Programming Format 1660 Barcode Scanner User Guide 4. Turn on the scanner with correct WPAN settings, such as select BT SPP or BT HID, broadcasting enabled, authentication enabled, and PIN code specified, etc. Select the check box of [My device is set up and ready to be found] on your computer. 5. Click [Next]. 6. Wait for a few seconds for the Wizard to search available devices nearby. The scanner will appear with its “serial number” as the device name. You may double-check the “Serial Number” label on the scanner to ensure connecting with the correct scanner. Select the target scanner. If the target scanner does not appear on the list, click [Search Again] to refresh the list. The scanner might enter Suspend Mode now, and you can press the trigger to have it active again (=discoverable). It will then stay active for a specified period of time (2 minutes by default) and wait for PC to establish a connection. 7. Click [Next].](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-96.png)
![89 Update Chapter 3 8. Enter the passkey for authentication, which must be exactly the same as configured for the scanner. 9. Click [Next]. Wait for a few seconds for Windows to exchange passkeys.](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-97.png)
![91 Update Chapter 3 Note: When Bluetooth security is enabled without providing a pre-set PIN code, dynamic input of PIN code is supported. 10. Click [Finish]. 1660/1661 as BT SPP Slave 1660/1661 as BT SPP Master](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-99.png)
![95 Update Optical Characteristics 1660 1661 Scan Engine Non-contact type Optical Sensor CCD, 2500 pixels Light Source Visible red LED RF Characteristics WPAN Module Wireless PAN BT Class 3 compliance Coverage (line-of-sight) 10 meters with 3610 Interface Supported Serial Port Profile (BT SPP) Human Interface Device Profile (BT HID) 3610 Physical Characteristics Memory 1 KB for transmit buffer 256 KB flash for memory mode Switch Push-button switch for [Trigger] key, plus [Power/Delete] key Indication Triple-color LED (Red/Green/Blue) and beeper Dimensions 95 mm (L) 35 mm (W) 20 mm (H) Weight Approx. 50 g SPECIFICATIONS](https://usermanual.wiki/CipherLab/1661/User-Guide-1392203-Page-103.png)
