CipherLab 2220 OMNIDIRECTIONAL PRESENATION SCANNER User Manual 2200 Scanner User Guide v1 00
CipherLab Co., Ltd. OMNIDIRECTIONAL PRESENATION SCANNER 2200 Scanner User Guide v1 00
User manual.pdf
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3682224 |
| Application ID | EECbb9JwbFNgwHeqGrPMAw== |
| Document Description | User manual.pdf |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 37.14kB (464237 bits) |
| Date Submitted | 2017-12-18 00:00:00 |
| Date Available | 2017-12-18 00:00:00 |
| Creation Date | 2017-11-24 17:04:33 |
| Producing Software | Acrobat Distiller 11.0 (Windows) |
| Document Lastmod | 2017-12-11 13:07:43 |
| Document Title | Microsoft Word - 2200 Scanner User Guide_v1.00 |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | gary.lin |
2200 Omnidirectional Presentation Scanner Setup barcodes included. Version 1.00 Copyright © 2017 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. Due to continued product development this information may change without notice. The information and intellectual property contained herein is confidential between CIPHERLAB and the client and remains the exclusive property of CIPHERLAB CO., LTD. If finding any problems in the documentation, please report them to us in writing. CIPHERLAB does not warrant that this document is error-free. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of CIPHERLAB CO., LTD. For product consultancy and technical support, please contact representative. Alternatively, visit our web site for more information. the local sales The CipherLab logo is a registered trademark of CIPHERLAB CO., LTD. All brand, product and service, and trademark names are the property of their registered owners. The editorial use of these names is for identification as well as to the benefit of the owners, with no intention of infringement. CIPHERLAB CO., LTD. Website: http://www.cipherlab.com IMPORTANT NOTICES FOR USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FOR EUROPE This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: - EN 60950-1: 2006+A11:2009+A1:2010+A12:2011+A2:2013 Safety of Information Technology Equipment - EN 301 489-1 V2.1.1: 2016 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements - EN 301 489-3 V2.1.0: 2016 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and 40 GHz - EN 302 208-1 V3.1.1: 2016 Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz with power levels up to 2 W and in the band 915 MHz to 921 MHz with power levels up to 4 W; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU SAFETY PRECAUTIONS DO NOT expose the scanner to any flammable sources. Under no circumstances, internal components are self-serviceable. For AC power adaptor, a socket outlet shall be installed near the equipment and shall be easily accessible. Make sure there is stable power supply for the scanner or its peripherals to operate properly. CARE & MAINTENANCE Use a clean cloth to wipe dust off the scanning window and the body of the scanner. DO NOT use/mix any bleach or cleaner. If finding the scanner malfunctioning, write down the specific scenario and consult the local sales representative. RELEASE NOTES Version Date Notes 1.00 Nov. 24, 2017 Initial Release CONTENTS IMPORTANT NOTICES .......................................................................................................... - 3 For USA ....................................................................................................................................... - 3 For Europe .................................................................................................................................. - 4 Safety Precautions .................................................................................................................. - 4 Care & Maintenance ............................................................................................................... - 4 RELEASE NOTES ...................................................................................................................... - 5 INTRODUCTION .......................................................................................................................... 1 Inside the Package ...................................................................................................................... 2 Product Highlights ....................................................................................................................... 2 Symbologies Supported ............................................................................................................ 3 QUICK START ............................................................................................................................... 5 Enter Configuration Mode ......................................................................................................... 6 Exit Configuration Mode ............................................................................................................ 6 Default Settings ........................................................................................................................... 7 Save User Settings as Defaults......................................................................................... 7 Restore User Defaults ........................................................................................................... 7 Restore System Defaults ..................................................................................................... 7 Read a Setup Barcode ............................................................................................................... 8 Configure Parameters ........................................................................................................... 8 List the Current Settings ................................................................................................... 12 Create One-Scan Setup Barcodes ....................................................................................... 14 1D One-Scan Barcode ........................................................................................................ 14 2D One-Scan Barcode ........................................................................................................ 15 SPECIFICATIONS ..................................................................................................................... 17 FIRMWARE UPGRADE ............................................................................................................ 19 Using RS-232 .............................................................................................................................. 19 Using USB Virtual COM............................................................................................................ 21 HOST SERIAL COMMANDS ................................................................................................... 23 Serial Commands ...................................................................................................................... 23 Example......................................................................................................................................... 24 KEYBOARD WEDGE TABLE................................................................................................... 25 Key Type & Status..................................................................................................................... 27 Key Type .................................................................................................................................. 27 Key Status ............................................................................................................................... 27 Example......................................................................................................................................... 28 2200 Omnidirectional Presentation Scanner User Guide NUMERAL SYSTEMS ................................................................................................................ 29 Decimal System ......................................................................................................................... 29 Hexadecimal System ................................................................................................................ 30 ASCII Table .................................................................................................................................. 31 READING DRIVER LICENSES ............................................................................................. 33 License Parsing Setup .............................................................................................................. 33 File Type................................................................................................................................... 33 Output Sequence Setup .......................................................................................................... 34 Separators and Fields .............................................................................................................. 40 Edit Separators ...................................................................................................................... 41 Edit Fields ................................................................................................................................ 42 KEYBOARD TYPE ONE-SCAN BARCODE ........................................................................ 43 Keyboard Wedge........................................................................................................................ 43 Direct USB HID ........................................................................................................................... 48 INTRODUCTION Equipped with a 2D barcode reader, the scanner is capable of reading 1D and 2D barcodes. The scanner is designed for desktop use with ease of installation. For particular deployment, the scanner can be integrated with other devices, like POS, to achieve systematic data colletion. This manual contains information on operating the scanner and using its features. It is better to keep one copy of the manual at hand for quick reference or maintenance purposes. To avoid any improper disposal or operation, please read the manual thoroughly before use. Thank you for choosing CipherLab products! Update 2200 Omnidirectional Presentation Scanner User Guide INSIDE THE PACKAGE The items included in the package may be different, depending on order. Rich choices of output interfaces are available to enhance the total performance of the scanner. Refer to product specifications. Save the box and packaging material for future use in case it is need to store or ship the scanner. PRODUCT HIGHLIGHTS Small-form-factor and built tough to survive drop test Supports a variety of 2D symbologies Extremely low power consumption Firmware upgradeable Supports most popular barcode symbologies, including GS1-128 (EAN-128), GS1 DataBar (RSS), etc. Supports different scan modes, including Aiming Mode and Multi-Barcode ModeNote Programmable feedback via LED indicator and beeper Beeping tone and duration programmable for Good Read Provides choices of output interfaces, including RS-232, Keyboard Wedge, and USB. Programmable parameters include data output format, editing format, symbologies, etc. Note: In any scan mode other than Multi-Barcode Mode, a barcode acceptable to the scanner can only contain data of 7 KB at most. Enter Setup 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 SYMBOLOGIES SUPPORTED Most of the popular barcode symbologies are supported, as listed below. Each can be individually enabled or disabled. The scanner will automatically discriminate and recognize all the symbologies that are enabled. Refer to Chapter 3 錯誤! 找不到參照來源。 for details of each symbology. Symbologies Supported: Enable/Disable Default Codabar Enabled Code 93 Enabled MSI Disabled Plessey Disabled Telepen Disabled Code 128 Code 2 of 5 Code 128 Enabled GS1-128 (EAN-128) Enabled ISBT 128 Enabled Industrial 25 Enabled Interleaved 25 Enabled Matrix 25 Code 3 of 9 EAN/UPC Code 39 Disabled Enabled Italian Pharmacode Disabled French Pharmacode Disabled EAN-8 Enabled EAN-8 Addon 2 Disabled EAN-8 Addon 511109951 Disabled EAN-13 Enabled EAN-13 & UPC-A Addon 2 Disabled EAN-13 & UPC-A Addon 5 Disabled ISBN Disabled UPC-E0 Enabled UPC-E1 Disabled UPC-E Addon 2 Disabled UPC-E Addon 5 Disabled UPC-A Enabled Code 11 GS1 DataBar Disabled GS1 DataBar Omnidirectional (RSS-14) Disabled Update 2200 Omnidirectional Presentation Scanner User Guide (RSS) GS1 DataBar Truncated Disabled GS1 DataBar Limited (RSS Limited) Disabled GS1 DataBar Expanded (RSS Expanded) Disabled Composite Code Composite CC-A/B Disabled Composite CC-C Disabled 2D Symbologies PDF417 Enabled MicroPDF417 Disabled Data Matrix Enabled Maxicode Enabled QR Code Enabled MicroQR Enabled Aztec Enabled Han Xin Disabled Enter Setup QUICK START The configuration of the scanner can be done by reading the setup barcodes (setup labels) contained in this manual or via the ScanMaster software. This section describes the procedure of configuring the scanner by reading the setup barcodes and provides some examples for demonstration. Note: If RS-232 or USB Virtual COM is selected for output interface, the host can directly send serial commands to configure the scanner. For example, run HyperTerminal.exe and type the 6-digit command located under each setup barcode. Refer to Appendix II Host Serial Commands. Update 2200 Omnidirectional Presentation Scanner User Guide ENTER CONFIGURATION MODE For the scanner to enter the configuration mode, have it read the "Enter Setup" barcode located at the bottom of almost every even page of this manual. The scanner will respond with six beeps and its LED indicator will become flashing red after reading the barcode. Enter Setup For configuring scanner parameters, see “Read a Setup Barcode” below. EXIT CONFIGURATION MODE For the scanner to save settings and exit the configuration mode, have it read the “Update” barcode located at the bottom of almost every odd page of this manual. To exit the configuration mode without saving any changes, have the scanner read the “Abort” barcode instead. Just like reading the “Enter Setup” barcode, the scanner will respond with six beeps and its LED indicator will become flashing red after reading the barcode. Wait for a few seconds for the scanner to restart itself. Update Abort Enter Setup 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 DEFAULT SETTINGS SAVE USER SETTINGS AS DEFAULTS For the scanner to keep the customized settings as user defaults, have it read the “Save as User Defaults” barcode. This is a normal setup barcode, and the scanner will respond with two beeps (low-high tone). After reading the “Update” barcode, the current settings will be saved as user defaults. Save as User Defaults RESTORE USER DEFAULTS For the scanner to restore the user defaults saved earlier, have it read the “Restore User Defaults” barcode. This is a normal setup barcode, and the scanner will respond with two beeps (low-high tone). After reading the “Update” barcode, all the parameters of the scanner will return to their customized values. Restore User Defaults RESTORE SYSTEM DEFAULTS For the scanner to restore the factory defaults, have it read the “Restore System Defaults” barcode. This is a normal setup barcode, and the scanner will respond with two beeps (low-high tone). After reading the “Update” barcode, all the parameters of the scanner will return to their default values. Restore System Defaults Note: The system default value (if there is) for each setting is indicated by an asterisk “*”. Update 2200 Omnidirectional Presentation Scanner User Guide READ A SETUP BARCODE CONFIGURE PARAMETERS For most of the scanner parameters, only one read is required to set them to new values. The scanner will respond with two beeps (low-high tone) when each parameter is set successfully. But for a number of special parameters, multiple reads are required to complete the setting. In this case, the scanner will respond with a short beep indicating it needs to read more setup barcodes. These special parameters may require reading one or more setup barcodes, such as Numeric barcodes, say, for keyboard type, inter-character delay, length qualification Hexadecimal barcodes, say, for character strings as prefix, suffix, etc. When “Keyboard Wedge” or “USB HID” is configured as the interface, Key Type and Key Status will then become applicable. Decide whether or not to change key status when “Normal Key” is selected for Key Type. To complete the configuration of these special parameters, it requires reading the “Validate” barcode, and then the scanner will respond with two beeps (low-high tone) to indicate the input values are validated. Enter Setup 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 The example below shows how to save settings as “User Default” to restore user defaults later: Steps Action Scanner Feedback if Successful Power on the scanner… The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will be flashing red. Read a Setup barcode… The scanner will respond with two beeps (low-high tone) if reading a normal setup barcode. For example, Exit the Configuration Mode… Same as for Enter the Configuration Mode. OR The scanner will automatically restart itself… Same as for Power on the scanner. When any configuration error occurs... The scanner will respond with one long beep (low tone). Update 2200 Omnidirectional Presentation Scanner User Guide The example below shows how to set numeric parameters: Steps Action Scanner Feedback if Successful Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red. Read a Setup barcode... The scanner will respond with two beeps (low-high tone) if reading a normal setup barcode. For example, Normal setup barcode Normal setup barcode The scanner will respond with one short beep if reading a special setup barcode such as “Max. Length”, indicating the setup requires reading more barcodes. Special setup barcode Read the “Decimal Value” barcode(s). Decimal barcodes Refer to System” Appendix IV “Decimal The scanner will respond with two beeps (low-high tone) when the input values are validated. Exit the Configuration Mode… Same as for Enter the Configuration Mode. OR The scanner will automatically restart itself… Same as for Power on the scanner. 10 Enter Setup 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 The example below shows how to set string parameters: Steps Action Scanner Feedback if Successful Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red. Read a Setup barcode... The scanner will respond with one short beep if reading a special setup barcode such as “Prefix Code”, indicating the setup requires reading more barcodes. For example, Special setup barcodes When “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. Decide whether or not to change key status when “Normal Key” is selected for Key Type. Refer to Appendix III Read the “Hexadecimal Value” barcodes for the desired character string. For example, read “2” and “B” for the scanner to prefix the character “+”. Hexadecimal barcodes Refer to Appendix IV “Hexadecimal System” The scanner will respond with two beeps (low-high tone) when the input values are validated. Exit the Configuration Mode… Same as for Enter the Configuration Mode. OR The scanner will automatically restart itself… Same as for Power on the scanner. 11 Update 2200 Omnidirectional Presentation Scanner User Guide LIST THE CURRENT SETTINGS The current settings of all scanner parameters can be sent to the host computer for user inspection. The listing includes pages as shown below. Select the page of interest by having the scanner read the “List Page x” barcode. The scanner will respond with two beeps (low-high tone) and send the selected page to the host immediately. Lists settings regarding Firmware Version, Serial Number, Interface, Buzzer, and Other Scanner Parameters Lists settings regarding Prefix, Length Code Setting (1/2) Suffix, Lists settings regarding Prefix, Length Code Setting (2/2) Suffix, List Page 1 and List Page 2 and List Page 3 Lists settings regarding Code ID List Page 4 Lists settings regarding: Readable Symbologies (1/2) List Page 5 Lists settings regarding: Readable Symbologies (2/2) List Page 6 Lists settings regarding Symbology Parameters (1/3) List Page 7 Lists settings regarding Symbology Parameters (2/3) List Page 8 Lists settings regarding Symbology Parameters (3/3) List Page 9 Reserved List Page 10 12 Enter Setup 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Lists settings regarding Editing Format 1 (1/2) List Page 11 Lists settings regarding Editing Format 1 (2/2) List Page 12 Lists settings regarding Editing Format 2 (1/2) List Page 13 Lists settings regarding Editing Format 2 (2/2) List Page 14 Lists settings regarding Editing Format 3 (1/2) List Page 15 Lists settings regarding Editing Format 3 (2/2) List Page 16 Lists settings regarding Editing Format 4 (1/2) List Page 17 Lists settings regarding Editing Format 4 (2/2) List Page 18 Lists settings regarding Editing Format 5 (1/2) List Page 19 Lists settings regarding Editing Format 5 (2/2) List Page 20 Lists settings of Driver License parsing List Page 22 13 Update 2200 Omnidirectional Presentation Scanner User Guide CREATE ONE-SCAN SETUP BARCODES Most of the scanner parameters require only one read for setting new values. To facilitate configuring the scanner, create One-Scan setup barcodes for use. 1D ONE-SCAN BARCODE The requirements of a One-Scan setup barcode are: a prefix of the “#@” characters the six digits of command parameters a suffix of the “#”character For example, the scanner needs reading three setup barcodes for the command parameter “109952” to take effect: Enter Setup List Page 3 Update Now, it requires only one read: One-Scan Setup Barcode for 109952 Note: The scanner will restart automatically upon reading the One-Scan setup barcode for changing the interface. It will respond with a long beep and its LED will come on-off shortly. 14 Enter Setup 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2D ONE-SCAN BARCODE Users can also scan a single 2D barcode combining with a series of serial commands to configure the scanner. For example, if you want to change the suffix character to ‘#’, you will need to input the serial commands in sequence as follows (underlining the digits is to make them more readable): #@CipherLab101231109902109903109994 Command Purpose #@CipherLab Enter Setup 101231 Configure suffix 109902 Give the first hexadecimal digit of 0x23 109903 Give the second hexadecimal digit of 0x23 for taking ‘#’ as the suffix 109994 Validate the settings The serial commands above can be combined to form a single 2D barcode: 2D One-Scan Setup Barcode for configuring suffix 15 Update 2200 Omnidirectional Presentation Scanner User Guide 16 Enter Setup SPECIFICATIONS Optical Characteristics 2200 Scan Engine 2D Imager Light Source Aiming pattern: 520~532nm LED Illumination: 616~625nm LED Physical Characteristics Indication Tri-color LED (Red/Green/Blue) and beeper Interface Options Keyboard Wedge, RS-232, USB HID, USB Virtual COM Weight Approx. 320g (2D Barcode Reader only); 380g (RFID included) Dimensions 150 x 83 x 80 mm Environmental Characteristics Temperature Humidity (Non-condensing) Operating 0 °C to 40 °C Storage -40 °C to 60 °C Operating 10% to 90% Storage 5% to 95% 17 Update 2200 Omnidirectional Presentation Scanner User Guide Resistance Splash / Dust Resistance IP 52 Electrostatic Discharge ± 15 kV air discharge, ± 8 kV contact discharge Programming Support Configuration via Setup Barcodes Use setup barcodes or host serial commands. Software Windows®-based ScanMaster Firmware upgradeable Download firmware updates via the download utility. Accessories (means “supported”) Keyboard Wedge Cable RS-232 Cable USB Cable Dual-USB Cable 18 Enter Setup Appendix I FIRMWARE UPGRADE USING RS-232 1) Connect the RS-232 cable between the scanner and the computer, and join the power supply cord. 2) Read the following barcodes in sequence to configure the scanner to use RS-232 as download interface. Enter Setup Activate RS-232 115200 bps Update 3) Read the following barcodes in sequence for the scanner to enter the download mode. The scanner will respond with beeps to indicate it is ready for downloading. Enter Setup Download 19 Update 2200 Omnidirectional Presentation Scanner User Guide 4) Run the download utility “ProgLoad.exe” on the computer. Kernel Program User Program K250x_V*.shx STD250x_V*.shx For the communication settings, select “RS-232” and the correct COM port for RS-232 or USB Virtual COM interface. For RS-232, select 115200 bps for baud rate; for USB Virtual COM, ignore the baud rate setting. For the file option, click [Browse] to select the target file for firmware update. Click [OK]. 5) After upgrading kernel, you will need to restart the scanner manually. After upgrading the user program, the scanner will automatically restart itself once the download is completed successfully. Note: The output interface remains unchanged as specified in step 2 (= RS-232 or USB Virtual COM). For RS-232, the baud rate setting is still 115200 bps! 20 Enter Setup Appendix I 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 USING USB VIRTUAL COM 1) Connect the USB cable between the scanner and the computer. If using USB Virtual COM for the first time, you must install its driver beforehand. 2) For Windows platform, read the following barcodes in sequence to configure the scanner to use USB VCOM_CDC as download interface. Enter Setup Activate Direct USB VCOM_CDC Update For non-Windows platform, read the following barcodes in sequence to configure the scanner to use USB Virtual COM as download interface. Enter Setup Activate Direct USB VCOM Update 3) Read the following barcodes in sequence for the scanner to enter the download mode. The scanner will respond with beeps to indicate it is ready for downloading. Enter Setup Download 4) Run the download utility “ProgLoad.exe” on the computer. 21 Update 2200 Omnidirectional Presentation Scanner User Guide Kernel Program User Program K250x_V*.shx STD250x_V*.shx For the communication settings, select “RS-232” and the correct COM port for RS-232 or USB Virtual COM interface. For RS-232, select 115200 bps for baud rate; for USB Virtual COM, ignore the baud rate setting. For the file option, click [Browse] to select the target file for firmware update. Click [OK]. 5) After upgrading kernel, you will need to restart the scanner manually. After upgrading the user program, the scanner will automatically restart itself once the download is completed successfully. Note: The output interface remains unchanged as specified in step 2 (= RS-232 or USB Virtual COM). For RS-232, the baud rate setting is still 115200 bps! 22 Enter Setup Appendix II HOST SERIAL COMMANDS SERIAL COMMANDS Purpose To disable the scanner. Remarks “D” Purpose To enable the scanner. Remarks “E” #@ nnnnnnPurpose To configure the scanner. Remarks nnnnnn – the six digits of command parameters. For example, “109952” is to list the current Code ID settings. List Page 3 Serial Command “0x23” + “0x40” + “0x31” + “0x30” + “0x39” + “0x39” + “0x35” + “0x32” + “0x0d” Note: After configuring the scanner, send the serial command “#@109999” to save the settings. #@ - - - - Purpose To halt the scanner. Remarks “0x23” + “0x40” + “0x2d” + “0x2d” + “0x2d” + “0x2d” + “0x0d” #@ . . . . Purpose To resume operation. Remarks “0x23” + “0x40” + “0x2e” + “0x2e” + “0x2e” + “0x2e” + “0x0d” #@//// Purpose To respond with a beep. Remarks “0x23” + “0x40” + “0x2f” + “0x2f” + “0x2f” + “0x2f” + “0x0d” 23 Update 2200 Omnidirectional Presentation Scanner User Guide #@TRIGOFF Purpose Disable software trigger Remarks “0x23” + “0x40” + “0x54” + “0x52” + “0x49” + “0x47” + “0x4f” + “0x46” + “0x46” + “0x0d” #@TRIGON Purpose Enable software trigger Remarks “0x23” + “0x40” + “0x54” + “0x52” + “0x49” + “0x47” + “0x4f” + “0x4e” + “0x0d” EXAMPLE Run HyperTerminal.exe on the host computer to send serial commands to the scanner via RS-232 or USB Virtual COM. For the scanner to stop immediately – For the scanner to resume working – For the scanner to change the beeper to medium volume and beep – #@101011 #@//// For the scanner to change the beeper to minimal volume and beep – #@101010 #@//// For the scanner to change the beeper frequency to 8 kHz (for Good Read Beep only) and beep – #@101001 #@//// For the scanner to change the beeper length to longest (for Good Read Beep only) and beep – #@101008 #@//// For the scanner to save the settings, send the serial command “#@109999” – #@101011 #@109999 Note: Configure more than one scanner connected to the host via RS-232 or USB Virtual COM. To identify the scanner, please end the serial command to have it respond with a beep. 24 Enter Setup Appendix III KEYBOARD WEDGE TABLE “Apply” Special Keyboard F2 SP INS F3 DLT F4 Home F5 End F6 Up F7 Down F8 Left F9 BS F10 HT F11 LF F12 Right ESC PgUp Exec CR CR* PgDn F1 Dly ENTER* Note: (1) ~: Digits of numeric keypad. (2) CR*/ENTER*: ENTER key on the numeric keypad. 25 Update 2200 Omnidirectional Presentation Scanner User Guide “Bypass” Special Keyboard SP BS HT LF Dly ESC CR Note: (1) ~: Digits of numeric keypad. (2) CR*/ENTER*: ENTER key on the numeric keypad. 26 Enter Setup Appendix III 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 KEY TYPE & STATUS KEY TYPE If “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. *Normal Scan Code KEY STATUS Decide whether or not to change key status when “Normal Key” is selected for Key Type. Add Shift Add Left Ctrl Add Right Ctrl Add Left Alt Add Right Alt 27 Update 2200 Omnidirectional Presentation Scanner User Guide EXAMPLE KEY TYPE = NORMAL For example, if you want to program the character “!” as the prefix code: 1. Read the “Configure Prefix” barcode. 2. Read the “Hexadecimal Value” barcode on page 30 for “2” and “1”. 3. Read the “Validate” barcode to complete this setting. KEY TYPE = SCAN CODE For example, if you want to program the character “a” (= “1C” on the scan code table) as the prefix code: 1. Read the “Configure Prefix” barcode. 2. Read the “Scan Code” barcode. 3. Read the “Hexadecimal Value” barcode on page 30 for “1” and “C”. 4. Read the “Validate” barcode to complete this setting. KEY TYPE = NORMAL + KEY STATUS = SHIFT For example, if you want to program the character “!” (= “Shift” + “1” on keyboard) as the prefix code: 1. Read the “Configure Prefix” barcode. 2. Read the “Add Shift” barcode. 3. Read the “Hexadecimal Value” barcode on page 30 for “3” and “1”. 4. Read the “Validate” barcode to complete this setting. KEY TYPE = NORMAL + KEY STATUS = CTRL For example, if you want to program “Ctrl+A” and “Ctrl+$” as the prefix code: 1. Read the “Configure Prefix” barcode. 2. Read the “Add Left Ctrl” barcode. 3. Read the “Hexadecimal Value” barcode on page 30 for “4”, “1” (= “A”). 4. Read the “Add Left Ctrl” barcode. 5. Read the “Hexadecimal Value” barcode on page 30 for “2”, “4” (= “$”). 6. Read the “Validate” barcode to complete this setting. 28 Enter Setup Appendix IV NUMERAL SYSTEMS DECIMAL SYSTEM Decimal Validate the Values Validate Update Abort 29 2200 Omnidirectional Presentation Scanner User Guide HEXADECIMAL SYSTEM Hexadecimal 30 Enter Setup Appendix IV 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Validate the Values Validate ASCII TABLE DLE SP SOH DC1 STX DC2 ETX DC3 EOT DC4 ENQ NAK ACK SYN BEL ETB BS CAN HT EM LF SUB VT ESC FF FS CR GS SO RS SI US DEL Update Abort 31 2200 Omnidirectional Presentation Scanner User Guide 32 Enter Setup Appendix V READING DRIVER LICENSES The scanner is capable of reading 2D driver’s licenses and other American Association of Motor Vehicle Administrators (AAMVA) compliant ID cards. For compliant 2D licensed card scanning, it decodes the information embedded in the ID cards to a formatted data. This appendix provides the setup barcodes required while ScanMaster utility provides GUI setup that is oganized and easy-to-use. Note: The configured settings are saved in flash memory for access once a driver’s license is read. LICENSE PARSING SETUP *License Parse Disable License Parse Enable Parse Field Clear FILE TYPE You can check the file type of ANSI by scanning the barcode as below. *Enable Disable Update Abort 33 2200 Omnidirectional Presentation Scanner User Guide OUTPUT SEQUENCE SETUP The scanner supports arranging the sequences of license embedded data via separators and fields. In order to present data in a consistent format, some barcodes (ex. First Name, Middle Name/Initial, Last Name, Name suffix, Name Prefix, Birth Date and so on) will return data based on the calculated actual data contained in the ID barcode. Full Name Last Name First Name Middle Name/Initial Name Suffix Name Prefix Mailing Address Line1 Mailing Address Line2 Mailing Address City Mailing Address State 34 Enter Setup Appendix V 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Mailing Address Postal Code Home Address Line1 Home Address Line2 Home Address City Home Address State Home Address Postal Code License ID Number License Class License Restrictions License Endorsements Height (Feet and/or Inches) Height (Centimeters) Update Abort 35 2200 Omnidirectional Presentation Scanner User Guide Weight (Pounds) Weight (Kilograms) Eye Color Hair Color License Expiration Date Birth Date Gender License Issue Date Issue Timestamp Number of Duplicates Medical Codes Organ Donor 36 Enter Setup Appendix V 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Nonresident Customer ID Social Security Number AKA Birth Date AKA Social Security Name AKA Full Name AKA Last Name AKA First Name AKA Middle Name/Initial AKA Name Suffix AKA Name Prefix Weight Range Update Abort 37 2200 Omnidirectional Presentation Scanner User Guide Document Discriminator Country Federal Commission Codes Place of Birth Audit Information Inventory Control Race/Ethnicity Std Vehicle Class Std Restrictions Std Endorsements Class Description Endorsement Description 38 Enter Setup Appendix V 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Restrictions Description Permit Class Permit Expiration Date Permit ID Number Permit Issue Date Permit Restrictions Permit endorsements Issuer ID Number Family Name Truncation First Name Truncation Middle Name Truncation Update Abort 39 2200 Omnidirectional Presentation Scanner User Guide SEPARATORS AND FIELDS Define the separators that separate fields during the transmission sequence of data scanning. In addition to the built-in data elements, you can also specify up to 5 Additional Fields with 4 bytes characters. Program the transmission sequence by reading the desired fields as additional fields. Note: Up to 5 separators can be assigned. Separator 1 (1 byte) *“Space” Separator 2 (1 byte) *“Enter” Separator 3 (1 byte) *“,” Separator 4 (1 byte) *“.” Separator 5 (1 byte) *“-” Additional Field 1 (4 bytes) Additional Field 2 (4 bytes) Additional Field 3 (4 bytes) Additional Field 4 (4 bytes) Additional Field 5 (4 bytes) 40 Enter Setup Appendix V 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 EDIT SEPARATORS All the driver license fields can be split with a pre-selected separator, for example, “-” as First Name-Last Name or “:” as First Name:Last Name. Edit Separator 1 Edit Separator 2 Edit Separator 3 Edit Separator 4 Edit Separator 5 1) Read the barcode above to apply separator to driver license information separately, and follow steps 2~3. 2) Read the “Hexadecimal Value” barcode for the desired character string. For example, read “3” and “A” for the separator to split the data with character [:]. 3) Read the “Validate” barcode on the same page to complete this setting. Update Abort 41 2200 Omnidirectional Presentation Scanner User Guide EDIT FIELDS Up to five additional fields can be created for each editing format; each of them is numbered from Additional 1 to Additional 5 accordingly. If “Bluetooth® HID” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. You may decide whether or not to apply Key Status when “Normal Key” is selected for Key Type. Key Type Key Status Scan Code Up to 2 scan code values are allowed. N/A Normal Key Up to 4 character strings are allowed. Add Shift Add Left Ctrl Add Left Alt Add Right Ctrl Add Right Alt Refer to Keyboard Wedge Table. Edit Additional Field 1 Edit Additional Field 2 Edit Additional Field 3 Edit Additional Field 4 Edit Additional Field 5 1) Read the barcode above to specify an additional field, one at a time. 2) Read the “Hexadecimal Value” barcode for the desired additional field. 3) Read the “Validate” barcode on the same page to complete this setting. 42 Enter Setup Appendix VI 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Appendix VI KEYBOARD TYPE ONE-SCAN BARCODE KEYBOARD WEDGE PCAT (US) PCAT (French) PCAT (German) PCAT (Italian) PCAT (Swedish) PCAT (Norwegian) PCAT (UK) PCAT (Belgium) Update Abort 43 2200 Omnidirectional Presentation Scanner User Guide PCAT (Spanish) PCAT (Portuguese) PS55 A01-1 PS55 A01-2 (Japanese) PS55 A01-3 PS55 001-1 PS55 001-81 PS55 001-2 PS55 001-82 44 Enter Setup Appendix VI 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 PS55 001-3 PS55 001-8A PS55 002-1, 003-1 PS55 002-81, 003-81 PS55 002-2, 003-2 PS55 002-82, 003-82 PS55 002-3, 003-3 PS55 002-8A, 003-8A IBM 3477 Type 4 (Japanese) Update Abort 45 2200 Omnidirectional Presentation Scanner User Guide PS2-30 IBM 34XX/319X, Memorex Telex 122 Keys User-defined table PCAT (Turkish) PCAT (Hungarian) PCAT (Swiss German) PCAT (Danish) PCAT (Russian) PCAT (Cyrillic on Russian) 46 Enter Setup Appendix VI 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 PCAT (Armenian) PCAT (Thai) Update Abort 47 2200 Omnidirectional Presentation Scanner User Guide DIRECT USB HID PCAT (US) PCAT (French) PCAT (German) PCAT (Italian) PCAT (Swedish) PCAT (Norwegian) PCAT (UK) PCAT (Belgium) PCAT (Spanish) 48 Enter Setup Appendix VI 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 PCAT (Portuguese) PS55 A01-2 (Japanese) User-defined table PCAT (Turkish) PCAT (Hungarian) PCAT (Swiss German) PCAT (Danish) PCAT (Russian) PCAT (Cyrillic on Russian) Update Abort 49 2200 Omnidirectional Presentation Scanner User Guide PCAT (Armenian) PCAT (Thai) 50 Enter Setup
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2017:12:11 13:07:43+08:00 Create Date : 2017:11:24 17:04:33+08:00 Metadata Date : 2017:12:11 13:07:43+08:00 Format : application/pdf Title : Microsoft Word - 2200 Scanner User Guide_v1.00 Creator : gary.lin Producer : Acrobat Distiller 11.0 (Windows) Document ID : uuid:a9b1c235-0061-41a4-8fa5-cbdcbdd57f89 Instance ID : uuid:74e7fc85-2718-4245-bce9-687cfcf58fc0 Page Count : 58 Author : gary.linEXIF Metadata provided by EXIF.tools